Buy by engine size as the maker prints it for that unit, not by the biggest amp number, and read these printed things too: the kind of battery inside, the safety protections, the temperature and recharge rules, the use limits, and the warranty. The makers name their amp figures differently (peak, cranking, start assist, starting, instant) and print different engine sizes for the same peak number, so the figures cannot be compared across brands. Do not jump-start a battery that is frozen, cracked, bulging, leaking, low on fluid or smells of rotten eggs; have it replaced or serviced instead. The override or boost button switches the unit's safety protections off. Use it only if your unit's manual says to, only on a 12-volt lead-acid battery, and only after you have checked that the clamps are on the right posts. Do not leave a lithium jump starter in direct sunlight, on a hot dashboard or in a parked car in hot weather, and stay inside the temperature limits in its manual. Stop using a jump starter that swells, gets very hot, smells, leaks or has been damaged, keep it away from anything that can burn, and contact the maker. If the engine does not start after three tries, stop: the car probably needs service, not another jump. This page names no best jump starter and ranks none, PulsCar sells no jump starters, and no link here is an affiliate link. Our advice: if a maker prints no engine size for a unit, ask the maker. Our jump-start guide covers the steps.
This page answers one question: which jump starter should you buy, what should you compare, and when is it not enough. It is not about using one step by step (our jump-start guide covers the cable order, hybrids and electric cars, and the federal recall records), why your battery died (why a car battery keeps dying), how to test it (how to test a car battery) or which battery to buy (the car battery buying guide). PulsCar publishes this guide; it sells no jump starters, chargers or batteries. We did not test any jump starter. Everything below is what makers, a battery trade body, a standards owner, federal agencies, car makers, a roadside club and one independent tester print, each named. 🟢 Official marks federal pages and data. We print no prices. Where sources disagree, we show both and do not average them.
The seven things to compare, and where each is printed
The rest of this page takes each in turn, with the makers' exact words where they matter. The units in every table are in alphabetical order by maker; that is not a ranking, and no table says which unit is better. Where a maker's own documents disagree with each other, we print both.
Pick the chemistry first: lithium, capacitor or lead-acid
The pages we read describe three kinds of power source. Most current units are lithium. Milwaukee's M18 HotShot runs on an M18 tool battery and uses internal capacitors. The oldest document we read, a Black+Decker manual copyrighted 2009, describes a sealed lead-acid unit.
One safety standard covers packs built on batteries or capacitors. UL Standards & Engagement describes UL 2743 as covering "portable and movable power packs provided with one or more batteries, electrochemical capacitors, or electrochemical capacitor modules." For a pack with a booster function, UL's scope says it is "used for providing a temporary power source to a depleted land vehicle battery, rated 24 V dc maximum, to provide emergency starting power." UL's page is a catalog page for the standard; it does not list which products pass.
Read the claims about that standard closely. Clore's JNC325 page lists "Certifications: Conforms to UL2743", and its manual's approvals line reads "SGS (Conforms to UL2743)." Antigravity's page says "UL listed battery cells." A claim that a unit conforms to a standard, a claim that its cells are listed, and a claim that the whole unit is listed by a testing laboratory are three different statements. When a box uses one of them, ask which.
The car battery's chemistry also limits what the unit is for. NOCO's user guide says: "The product is only compatible with 12-volt lead-acid batteries only." Clore's manual says: "Use the Jump Starter for jump starting lead-acid batteries only." Topdon's manual says the jump-starting function is "only applicable to 12V lead-acid battery vehicles." Gooloo's FAQ says its units "can only jump-start 12V battery." Antigravity's manual says its unit "is for jump-starting 12-volt starter batteries only." NOCO adds: "Do not jump start a battery if you are unsure of the battery's specific chemistry or voltage." If your car has anything other than a plain 12-volt lead-acid starting battery, the box does not settle it: your owner's manual does, and for hybrids and electric cars our jump-start guide reads what the car makers print.
The amp number: one box, five names
The figure printed biggest on a jump starter's box is an amp rating, and the pages we read call it by different names. Battery makers have a defined rating for batteries: Interstate Batteries explains cold cranking amps (CCA) as "the amount of amperage a battery can supply at zero degrees (-17.8 C) for 30 seconds while sustaining a voltage of at least 7.2 volts." The Battery Council International glossary defines the same rating as the load that a new, fully charged and conditioned battery at 0 °F can continuously deliver for 30 seconds while holding at least 7.2 volts on a 12-volt battery. That is a test with a temperature, a time and a voltage floor. We read no page from a jump-starter maker that gives a test for its own number. The independent tester we could read says: "a jump starter is generally rated by cold cranking amps (CCA) or sometimes peak amps (PA). But that doesn't mean you can easily figure out what types of vehicles a given model is actually capable of starting."
Three things stand out. First, one maker can print several numbers for one unit and they do not agree. For the XP-10-HD, Antigravity's page and sheet give a starting current of 300 A and its manual gives a start current of 400 A, with a peak of 650 A in all three. Antigravity's FAQ says the heavy-duty model "puts out an additional 50 Cranking Amps" over the XP-10, a third name. We cannot tell you which is the one to use; that is for the maker to say. Second, Clore prints a second number only on some units: the JNC660 shows peak and cranking amps, while the JNC325 title carries 2000 A and 450 SAA (its own "Start Assist Amps"). Third, the oldest document we read prints a figure with a time attached: Black+Decker's 2009 manual gives 450 amps instant and 300 amps at 5 seconds.
What follows for a buyer is narrow. The word on the box matters, a number from one maker cannot be set against a number from another, and no page we read says how the big number was measured. When a page prints two figures, ask which one the engine size is tied to; none of the pages we read says plainly.
The engine size each maker prints, side by side
The makers also print the engine sizes their units can start. We list them as printed, for the specific units named, with the rating the same page or manual gives. Nothing here is averaged or reconciled, and the table does not say that any unit will start any engine: starting depends on the car, the battery and the weather, and Clore's manual says as much about the number of starts (see below).
Read across the rows: the pairing of rating and engine differs by maker. At 1,200 peak amps, Schumacher prints up to 8.0 L gas and 6.0 L diesel, while Battery Tender's table prints 6.0 L gas and 4.0 L diesel (and another Battery Tender post says its 1,200-amp units cover most diesel engines up to 3.0 L). At 2000 peak amps, Milwaukee prints 8.1 L gas and 3.0 L diesel, Topdon 8.0 L and 6.0 L, Battery Tender 8.0 L and 6.5 L. At 3000 amps, three Gooloo units print three different diesel sizes (8, 7 and 6.5 L). Antigravity prints diesel up to 7.3 L, or 7 L in its table, for a peak of 600 to 650 A, while Battery Tender's table prints diesel sizes of 2.0 L for its 600-amp and 800-amp units and 3.0 L for its 1,000-amp unit. Every maker above that prints separate gas and diesel sizes prints the smaller figure for diesel.
What we can conclude is limited. The engine size on a maker's page is that maker's claim for that unit, and the claims do not line up with the peak numbers, so a buyer who sorts by peak amps sorts in an order the makers' own engine claims do not follow. The independent tester we could read adds that the power needed "also depends on the state of the battery and when the vehicle was designed and built," and that "older models will likely need more power than newer ones" of a similar size. Our advice: take your engine size and fuel from your owner's manual, find the line on the maker's page that names that size and that fuel, and if the page prints only a gas size and you drive a diesel, ask the maker before buying. That advice is ours; the rows above are what the makers print.
Capacity and the number of starts: printed in different ways
Beside the amp rating, the pages print a battery capacity (74 Wh for the Clore JNC325, 59.2 Wh for the Topdon JumpSurge 2000 Pro, 88.8 Wh for the Gooloo GP4000 and the Topdon JumpSurge 3000, and "CAPACITY: 18,000 mAh / 66.75 Wh" in the Antigravity XP-10 manual) and a number of starts. The makers print starts per charge in different forms, with different conditions:
Pages also set a minimum charge before you start. Clore's manual says: "When using as a jump starter, it is recommended that the unit be at or near 100% state of charge as indicated on the unit's display." Topdon's manual tells the user to regularly check the battery level and ensure it is above 50%. Antigravity's manual says: "Do not Jump-Start with less than 3 lights lit on Capacity Indicator." The independent tester calls capacity a "pretty pointless metric" for choosing a jump starter, because it does not set which engine a unit can start; it reflects only how many times the device can perform a start. It estimated that a large pickup needed about 0.25 Ah to start. That is one tester's view from one vehicle. The cautious reading: the number of starts is a claim with conditions, and the manual's minimum charge before you start is a rule.
Safety protections and the override button
Most of what a buyer sees about safety is a list of protections, in each maker's own words. Clore's JNC325 page lists "reverse polarity protection, backfeed protection, over-voltage protection, short circuit protection and overheat protection." Milwaukee prints "Spark Proof, Reverse Polarity, & Overheat Protection." Antigravity says its clamps "prevent reverse polarity connection, over-charge, over-discharge, short-circuit and back-charge." Gooloo's FAQ describes an "Over-Start Protection" that switches off the clamps if you start the vehicle more than 4 times in 2 minutes. A protection list does not tell you how well each works. The independent tester we could read connected units to the wrong posts on purpose, and wrote that the protection "confirms that each clamp is on the correct post before completing the circuit" and that "On models with no safety protection, the sparks were a sure sign that a model deserved dismissal." That guide has not been maintained since February 2023 and covers products we do not name.
The part that deserves a buyer's attention is the override button, called Manual Override (NOCO), override (Clore, Milwaukee, Schumacher) or BOOST (Antigravity, Gooloo, Topdon). It exists because a protected unit will not connect to a battery that is too flat to be detected. The makers print different thresholds, and Antigravity, Clore, NOCO and Topdon say it switches the protections off:
The makers print the line at 2 volts, 3 volts, 1.2 volts and 1.0 volt, so read your unit's manual and not a chart. NOCO's GB40 guide adds: "IF YOU ARE UNSURE ABOUT USING THIS MODE, DO NOT ATTEMPT AND SEEK PROFESSIONAL HELP." The rule we use on this page: The override or boost button switches the unit's safety protections off. Use it only if your unit's manual says to, only on a 12-volt lead-acid battery, and only after you have checked that the clamps are on the right posts.
One more rule belongs beside it. Clore's manual says: "Never use an output cable/clamp assembly other than the one that was included with your unit." Topdon's says: "ONLY use the battery clamps that come with this product." The makers' rule is to use the set that came in the box.
Heat, cold and storage: the printed limits
The makers print temperature limits differently. Each limit below is as printed, for the unit named.
Several of these sentences matter for where you keep the unit. Antigravity's manual says: "Do not leave the product in or expose product to extremely high temperatures such as direct hot sunlight, or on dashboards or other extremely hot areas above 110°F (43°C). Swelling may occur." Topdon's manual says: "DO NOT put the product under direct sunlight or in high temperature areas." Antigravity's FAQ adds that a car parked in direct sunlight can reach between 131 and 172 degrees Fahrenheit on an 80 to 100 degree day, and that if you store the unit in the car out of the sun, such as the glovebox or the trunk, "in many areas it will very likely get too hot to just be left in the car." Clore and Gooloo print limits up to 140°F (Gooloo also says not to store its unit in a vehicle parked in hot weather for long periods), and NOCO says its units are meant to be stored indoors. Our advice, which no maker prints in these words: check the limit in your unit's manual against the hottest day in your area, and take the unit indoors when it is hotter. The rule we use on this page: Do not leave a lithium jump starter in direct sunlight, on a hot dashboard or in a parked car in hot weather, and stay inside the temperature limits in its manual.
Cold is the other half. Battery Tender's blog says: "Lithium jump starters perform best at temperatures above 32°F" and to warm a very cold unit inside the vehicle for 10 to 15 minutes. Clore's manual says the unit "may be used under any weather condition – rain, snow, hot or cold temperatures," and also that for optimum performance "do not store your Jump Starter below 50°F when using as a jump starter." We cannot reconcile these for you; your unit's manual says how a cold unit behaves.
When the unit is damaged: what OSHA, the makers and the EPA say
OSHA's safety bulletin on lithium batteries (🟢 Official, SHIB 06-20-2019) says they are normally safe, but "may cause injury if they have design defects, are made of low quality materials, are assembled incorrectly, are used or recharged improperly, or are damaged." It tells readers to inspect devices for "bulging/cracking, hissing, leaking, rising temperature, and smoking" before use, and: "Immediately remove a device or battery from service and place it in an area away from flammable materials if any of these signs are present." The bulletin is general and does not mention jump starters.
The makers say the same in their own terms. NOCO's guide says: "If the product battery is excessively hot, emitting an odor, deformed, cut, or is experiencing or demonstrating an abnormal occurrence, immediately stop all use and contact NOCO." Antigravity's manual says to stop use if swelling occurs and contact the manufacturer; its FAQ lists three typical causes of swelling (a very hot place such as a car interior or dashboard, overuse such as starting a motor larger than the unit was intended to start or starting several times in a row without cooling, and over-discharge or a very long time unused). Clore's manual says: "If the Jump Starter receives a sharp blow or is otherwise damaged in any way, have it checked by a qualified service person." The rule we use on this page: Stop using a jump starter that swells, gets very hot, smells, leaks or has been damaged, keep it away from anything that can burn, and contact the maker.
At the end of its life the unit is a lithium battery product. The EPA's page (🟢 Official) says lithium-ion batteries and devices containing them "should NOT go in household garbage or recycling bins," and that they should be taken to separate recycling or household hazardous waste collection points. The rule we use: Do not put a lithium jump starter in household trash or the recycling bin; take it to a battery recycling point.
Keeping it charged: the printed rules, and where they disagree
A jump starter that is flat when you need it is the same problem you bought it to solve. The makers print their own recharge rules, and they are not the same:
The clearest disagreement: Clore says to keep its lithium unit at full charge and recharge it every three months; Battery Tender says storing at 100% for extended periods accelerates lithium cell degradation and recommends 50 to 80% for storage. Schumacher says a lithium unit can be ready after up to a year in storage, and Antigravity says up to 6 months. The independent tester says to assume any battery pack loses 2 to 5 percent of its charge every month it sits. We do not choose between them. Our advice: write the maker's interval for your unit in your calendar on the day you buy it, and recharge after every use, a rule Clore, Battery Tender and Black+Decker all print.
The warranty, and what quietly voids it
The warranty terms are printed in the manuals and on warranty pages, and they differ in length and in conditions:
Two things follow. First, a warranty can depend on who sold you the unit: Antigravity's manual voids its warranty if the unit was not bought from an authorized dealer or not registered within 30 days, and Schumacher's page voids its warranty if the unit is resold through an unauthorized retailer. Our advice: before you buy, find the maker's page on authorized sellers, and register the unit on the day it arrives if the warranty asks. Second, length is not the only term: NOCO's guide excludes damage from operating the product outside its published guidelines, which it says include its technical specifications and user manuals. We cannot say what any maker will do in a real claim.
The use limits the makers print (not the steps)
The cable order and the clamp that goes last are in our jump-start guide, which reads car makers and two jump-pack makers on the steps. What a buyer should know before choosing is the set of limits each maker prints for its own unit, because they decide how forgiving the unit is on a bad morning:
The numbers differ, and the logic is mostly the same: a short window and, from most makers, a rest and a limit on tries (Clore's four and NOCO's five in 15 minutes are looser than our three-tries rule). Clore gives its reason for the fourth-attempt rule: "either the unit does not have sufficient power to start the vehicle or there is a more extensive problem with the vehicle than simply a depleted battery." Black+Decker's manual says: "If the engine fails to start after the recommended number of attempts, discontinue jump-start procedure and look for other problems that need to be corrected." The rule we use on this page: If the engine does not start after three tries, stop: the car probably needs service, not another jump.
Black+Decker's manual says to read the vehicle manual before jump-starting a vehicle with on-board computerized systems "to confirm that external-starting assistance is advised." Your owner's manual decides what is allowed on your car.
The shortlist, by situation, from what each maker prints
This is not a ranking and not a list of products we recommend. Each group is a situation; inside each group the units are alphabetical by maker. Each row gives only what the maker's own page or manual prints, and says what the page does not print. We verified none of it by use.
You already own a cordless tool battery system. Milwaukee's M18 HotShot 3841-20 is the one unit we read that runs on a tool battery: it is powered by an M18 battery and uses internal capacitors, so its page prints a -4°F to 122°F performance range and "no maintenance or pre-charging" for the unit; the page names M18 REDLITHIUM XC5.0 and above as the batteries it is optimized for. Our advice: read the manual of the M18 battery you use.
You want a small lithium unit. The rows differ in what they print about engine size.
You drive a larger engine or a diesel, as the makers print it. These pages name a gas size of 8 L or more (Milwaukee's 8.1 L is in the tool-battery row above).
NOCO's GB70 prints "Peak Current Rating: 2000A" and no engine size, so it is not in this group.
You want a shop-style unit that stays plugged in. Clore's JNC660 prints a built-in charger for staying plugged in; at 18 lbs it is the heaviest weight any page we read prints.
You also want a charger in the same box. Battery Tender's blog describes its Charge N Start units as a lithium-ion jump pack with a smart charger. It says the charger side handles "all 12V battery types, including standard, AGM, GEL, and lithium." The same blog table prints the Charge N Start 1100 at 1,000 A with 5.0 L gas and 3.0 L diesel, and the 1120 at 1,200 A with 6.0 L gas and 4.0 L diesel.
Which jump starter should you buy, and does PulsCar sell or rank any? PulsCar publishes this guide and does not sell jump starters, chargers or batteries, no link on this page is an affiliate link, and we did not test any jump starter, so we name no best one. The printed pages give you a short list to compare: the engine size the maker prints for the unit and fuel, which you check against your own manual; the kind of battery inside and what the maker says about lead-acid or 12-volt compatibility; the safety protections and the override button; the temperature, recharge and use limits; and the warranty with its conditions about the seller and registration. The makers disagree on what the same peak number can start, so no rating is a safe shortcut. Where a source said something different from another, we printed both.
What a jump starter cannot do
A jump starter does one thing: it supplies enough current for one start. The pages we read say, in several ways, what it does not do.
It does not charge the battery. Optima's page says that jump starters, jumper cables and jump packs "are great tools to use in emergency situations, but none of them are battery chargers." After a jump the battery "is still deeply-discharged and needs to be fully-recharged to at least 12.6 volts with a battery charger as soon as possible." Optima sells batteries and chargers, so it has an interest; Battery Tender, which sells both packs and chargers, also says that a standalone jump starter only solves the emergency. Which charger to buy is a question for a different page.
It does not fix a battery that is frozen or damaged. Clore's manual says "NEVER charge or jump start a frozen battery," and NOCO's guide says "Do not jump start a frozen battery." The rule we use on this page: Do not jump-start a battery that is frozen, cracked, bulging, leaking, low on fluid or smells of rotten eggs; have it replaced or serviced instead.
It does not fit every battery or every car. The compatibility lines above (12-volt lead-acid, or 12-volt only) are printed in the manuals. Battery Tender's blog says that "Hybrids and EVs often restrict 12V jump points, so check the owner's manual first." Kia's and Hyundai's manuals say to use only a 12-volt power supply; our jump-start guide reads the hybrid and electric-car sections of many manuals. Follow your owner's manual; if it shows no jump procedure, ask roadside assistance or the dealer (our advice).
It does not tell you why the battery died. A unit that starts the car once does not say whether the battery is worn out, whether the alternator is charging, or whether something is draining it overnight. Our pages on why a car battery keeps dying, how to test a car battery, how to test an alternator and how long a car battery lasts cover that; the unit is a way to move the car to a place where the test can happen. If the car will not start with a jump starter attached, or starts and dies, the cause may be more than a flat battery: our clicking no-start guide covers what the sounds can mean.
Will a jump starter fix a battery that keeps dying, and can PulsCar's free sound check help? A jump starter gets a car with a flat battery through one start, and whether the battery then holds a charge is a question for a battery test, not for the unit in your hand. PulsCar's free sound check, where you film 30 seconds of the engine and get a result in about a minute according to the PulsCar home page read on 15 November 2026, does not test a battery and does nothing for a jump starter. The reason the battery died, and whether it will start the car tomorrow, is for a battery test, an alternator check and a look for something draining it overnight. If the car will not turn over, or only clicks, a battery test comes first, and the sound check is not a substitute for it.
What car makers, roadside clubs and fleets say about packs
Of the manuals our jump-start guide read, the ones that name a pack include Kia, whose Niro page speaks of "a 12V booster pack or jumper cables from another vehicle's 12V battery," and Hyundai, whose Nexo manual uses the same words. A manual that says nothing about packs is not saying no, and it is not saying yes. Your car's owner's manual and your jump starter's own manual decide; where they differ from this page, follow them.
Two outside readings add a caution. AAA's Central Pennsylvania club, in a blog about how its roadside providers jump a battery, says jump boxes are "the safer, more convenient option" compared with jumper cables, and that if the car dies again after the box is disconnected, "this points to a more significant issue with your battery." That is a regional club's blog, not a standard. North Carolina's Department of Transportation, in a safety procedure for its own vehicle fleet, makes UL-certified jump boxes, which it defines as units that meet UL 2743, the required primary method, and says traditional jumper-cable jump-starting is restricted and may be used only as a controlled last-resort contingency when an approved box is not available.
Recalls and fires: where to check a model
A jump starter is a lithium battery that can deliver a very large current, and recalls of such units exist. Our jump-start guide reads NHTSA's records of four equipment recalls of jump starters from 2015 to 2017, and we do not repeat them here. The Consumer Product Safety Commission keeps its own recall data. We searched its recall data service (🟢 Official, read 15 November 2026) for jump starter in recall descriptions and jumpstart in product names, and found two recalls, both from 2015:
Each recall covers certain units of one model, not a brand, and neither is today's status. The service finds records by the words in them, so there may be other recalls. The CPSC website itself refused our requests, so we read its data service, not the recall pages. Before you buy, and again if the unit is old, search the maker's name and model on the CPSC and NHTSA recall sites; both notices above say to stop using a recalled unit.
Flying with one
If you travel with a jump starter, the lithium rules for passengers apply. The FAA's page (🟢 Official) says spare lithium-ion batteries, "including power banks and cell phone battery charging cases, must be carried in carry-on baggage only," that lithium-ion batteries are "limited to a rating of 100 watt hours (Wh) per battery," with airline approval for larger ones in a narrow range, and that damaged or recalled batteries likely to create sparks or heat must not be carried aboard unless the battery has been removed or made safe. The page does not name jump starters. Antigravity's FAQ says its Micro-Start units meet the FAA criteria for carry-on, cannot be in checked baggage, and are under the 100 Wh limit, with the figure printed on each. The jump-starter capacities we read in watt-hours are all below 100 Wh, but no page says a given jump starter is accepted by an airline. Our advice: check the watt-hour figure on the label and ask the airline.
The one independent test we could read
We found one independent test of portable jump starters that was readable. It is Wirecutter's guide, The Best Portable Jump Starter, which carries this notice: "As of February 2023, we are no longer maintaining this guide." Its text says that it researched 40 lithium-ion jump starters and tested 12; its first tests were in spring 2017, and the last update came before February 2023. The page says Wirecutter may earn a commission when readers buy through its links, and its products are from those years, so we name none of its picks and none of its prices. What is useful is how it tested and what it says to look for.
On how it tested, the guide says its first round drained a Jeep's battery to between 9 and 10.5 volts before each test and recorded the current each unit delivered with a digital clamp meter; it calls this "not a perfect measurement." On a 5.7 L V8 pickup, one unit delivered "a little over 200 amps" and started it, and "Of the five jump starters we tested on that truck, only three managed to revive it." That is one tester, a few vehicles and several years ago; it is evidence that engine size on a box is a claim, not a promise.
On what to look for, the guide's criteria line up with what the makers print: starting power rated in CCA or peak amps that does not easily translate to vehicles; reverse-polarity protection as the feature that makes the unit easier to use; clamps and cables of uneven quality (it reports that seven of the 12 clamp sets it tried were made by the same factory or to the same design); and capacity, which it calls a "pretty pointless metric" for choosing. It also reports one maker's advice to fully charge its models every three to six months. We cannot say whether any current unit meets any of this; use the guide as a list of questions to ask about any unit.
Three traps that leave you with the wrong unit or a flat one
Trap one: reading the biggest amp number as a promise for your engine. The pages we read print the rating under five names and tie the same number to different engines: Schumacher's 1200 peak amps goes with 8.0 L gas and 6.0 L diesel, Battery Tender's 1,200 amps with 6.0 L gas and 4.0 L diesel, Milwaukee's 2000 peak amps with 8.1 L gas and 3.0 L diesel. A buyer who sorts by peak amps is sorting by a number the makers do not define. The way out is on the page itself: your engine and fuel from your owner's manual, and the line on the maker's page that names that size.
Trap two: treating the unit as something that stays ready on its own. Clore says to keep its lithium unit at full charge and recharge every three months, Battery Tender says to store lithium cells at 50 to 80%, and Antigravity's FAQ says a car parked in the sun can reach 131 to 172 degrees Fahrenheit on an 80 to 100 degree day, above the 110 degree storage limit Antigravity's manual prints. A unit that spends a summer on a hot dashboard, or a year in a trunk with no check, is a unit you have not tested. Our advice: put the first recharge date in your calendar on the day you buy, and recharge after every use. Do not leave a lithium jump starter in direct sunlight, on a hot dashboard or in a parked car in hot weather, and stay inside the temperature limits in its manual.
Trap three: treating the jump as the repair, or the override as the first resort. A jump gets one start. AAA's club says that a car that dies again after the box is disconnected points to a more significant issue with the battery, and Optima says the battery is still deeply discharged and needs a charger. The override button is for a battery too flat to be detected, and Antigravity, Clore, NOCO and Topdon print that it switches the protections off. The override or boost button switches the unit's safety protections off. Use it only if your unit's manual says to, only on a 12-volt lead-acid battery, and only after you have checked that the clamps are on the right posts. On a battery that is frozen, swollen or leaking, do not jump at all: Do not jump-start a battery that is frozen, cracked, bulging, leaking, low on fluid or smells of rotten eggs; have it replaced or serviced instead.
Three typical situations
These are composite scenarios, not individual customers. They are built only from facts already on this page.
The diesel pickup. A driver with a diesel pickup reads the engine-size table and finds that the maker's page for the unit they like prints no engine size at all. They check their own manual for the engine size, ask that maker in writing which diesel size the unit is rated for, and do not buy until they have the answer. They treat the peak number as a label, not a promise.
The glovebox in a hot place. A driver in a hot climate keeps a lithium unit in the glovebox. They read Antigravity's FAQ on car interiors reaching 131 to 172 degrees and the 110 degree storage limit in its manual, compare it with their own unit's manual, and move the unit indoors for the summer. They recharge after each use and set a calendar date for the check.
The second jump in a week. A driver whose car needed a jump on Monday needs another on Friday. The unit started the car both times, and the driver does not read that as a fix: AAA's club and Optima both point to the battery. They get the battery tested and charged with a charger, as Optima says. If the unit swells, gets very hot, smells, leaks or has been damaged, they stop using it, keep it away from anything that can burn and contact the maker.
What this page cannot tell you
We did not test any jump starter, any amp rating or any engine claim, and we name no best one. We cannot say that any unit starts the engine its maker says it starts, that any protection works, or that any certification is genuine. We found one independent test we could read, and it has not been maintained since February 2023; Consumer Reports and three car and consumer-technology publishers had no page at the addresses we tried, and we did not get around any of them. Several pages we read are blog posts that describe a line of products and not one unit; we say so where it matters.
We could not read the product pages of Battery Tender, Gooloo, Schumacher and the US Topdon site, because they limited our requests, and we did not get around that; we read those makers' blogs, FAQs and warranty pages and, for Topdon and NOCO, their manuals. NOCO's website refused us, so we used its PDF guides for the GB40 and GB70, which print no engine sizes. We did not find the Schumacher manuals at the addresses we tried. DeWalt's and Craftsman's product pages gave us no text, and a Harbor Freight page refused us. We read no car manual for this page except the lines reused from our jump-start guide: your own owner's manual decides.
What could we not read for this page, and does PulsCar fill the gap? We could not read four makers' product pages, NOCO's website, the CPSC website itself, or any independent test newer than 2023: pages limited our requests, refused us or were not where we looked, and we did not get around any of them. PulsCar does not fill the gap: its free sound check, where you film 30 seconds of the engine and get a result in about a minute according to the PulsCar home page read on 15 November 2026, does not test a battery and does nothing for a jump starter. For a unit we could not read, the maker's own manual and the box win over anything printed here; the best use of this page is its questions: what engine and fuel does the maker print, what is the rating called, what battery is inside, and what do the heat, recharge and warranty lines say.
Your action plan: now, before you buy, and every few months
Now (ten minutes). Find your engine size and fuel in your owner's manual, and the manual's page on jump-starting: what it says about a booster pack, and about hybrid, start-stop or electric systems if your car has one.
Before you buy. For each unit, write down five things from the maker's own page or manual: the name of the amp rating, the engine and fuel size the maker prints, the battery kind and its compatibility line, the temperature and recharge rules, and the warranty with its conditions. If a page does not print the figure you need, treat that as an unanswered question for the maker. Check the model against recall lists, and whether the seller is an authorized one if the warranty asks.
The week it arrives. Register the unit if the warranty asks, charge it fully, put the recharge date in your calendar, and keep it where the heat limit allows. Read the override paragraph of its manual once, with the unit in your hand. The override or boost button switches the unit's safety protections off. Use it only if your unit's manual says to, only on a 12-volt lead-acid battery, and only after you have checked that the clamps are on the right posts.
When you use it. Follow the order in your owner's manual and the unit's manual; our jump-start guide reads the order the makers print. If the engine does not start after three tries, stop: the car probably needs service, not another jump. Do not jump-start a battery that is frozen, cracked, bulging, leaking, low on fluid or smells of rotten eggs; have it replaced or serviced instead.
Afterwards. Recharge the unit. Get the battery tested and charged with a battery charger; see how to test a car battery and why a car battery keeps dying. Stop using a jump starter that swells, gets very hot, smells, leaks or has been damaged, keep it away from anything that can burn, and contact the maker. Do not put a lithium jump starter in household trash or the recycling bin; take it to a battery recycling point.
Sources and documents
Every page below was read. Pages marked 5 November 2026 were read for our jump-start guide or our car battery buying guide and re-used here; the others were read on 15 November 2026. Marks: 🟢 federal text or data. Maker, trade body, standards-owner, club and publisher documents are named in words.
- UL 2743, Portable Power Packs, scope and edition summary (UL Standards & Engagement catalog page)
- 🟢 OSHA Safety and Health Information Bulletin, SHIB 06-20-2019, lithium battery fire and explosion injury
- 🟢 FAA PackSafe, lithium batteries (spare lithium ion batteries and power banks)
- 🟢 US EPA, Used Lithium-Ion Batteries
- 🟢 CPSC recall data service, search for jump starter (recall 15070) and for jumpstart (recall 15123)
- Battery Council International, battery terms (glossary, CCA) (read 5 November 2026)
- Interstate Batteries, Understanding CCA in Car Batteries (read 5 November 2026)
- Optima Batteries, the difference between a battery charger and a jump starter (blog, 28 September 2022) (read 5 November 2026)
- AAA Central Pennsylvania, emergency roadside assistance: jumping a battery (blog) (read 5 November 2026)
- North Carolina Department of Transportation, SOP 11E-7 Vehicle Jump-Start Procedures (read 5 November 2026)
- Kia Niro owner's manual, jump starting page (2026 edition) (read 5 November 2026)
- Hyundai Nexo owner's manual, 2023, jump starting pages (read 5 November 2026)
- Antigravity Batteries, XP-10-HD Micro-Start product page
- Antigravity Batteries, XP-10 Micro-Start product page
- Antigravity Batteries, XP-10-G2 Micro-Start product page
- Antigravity Batteries, XP-10-HD product sheet (PDF)
- Antigravity Batteries, Micro-Start XP-10-HD user manual (PDF, with the limited warranty)
- Antigravity Batteries, Micro-Start XP-10 user manual (PDF)
- Antigravity Batteries, FAQ: Micro-Start PPS
- Battery Tender, How to Use a Jump Starter Safely (blog)
- Battery Tender, How to Jumpstart a Battery: Portable Jump Starter Guide (2026) (blog)
- Black+Decker START-IT 450 Amp Jump-Starter/Air Compressor, VEC012CBD instruction manual (copyright 2009)
- Clore Automotive, Jump-N-Carry JNC325 product page
- Clore Automotive, JNC325 operator's manual (PDF)
- Clore Automotive, Jump-N-Carry JNC660 product page
- Gooloo, frequently asked questions
- Gooloo, About Jump Starter (blog)
- Milwaukee Tool, M18 HOTSHOT Jump Starter 3841-20 product page
- NOCO, Boost GB40 user guide and warranty (PDF, file code 03.07.2025A)
- NOCO, Boost GB70 user guide and warranty (PDF, file code 03.07.2025A)
- Schumacher Electric, Advantages of Lithium Jump Starters (blog, dated 6 December 2024)
- Schumacher Electric, warranty and registration page
- Topdon, JumpSurge 2000 Pro user manual (PDF)
- Topdon, JumpSurge 2000 user manual (PDF)
- Topdon, JumpSurge 3000 product profile (PDF)
- Wirecutter (The New York Times), The Best Portable Jump Starter (guide no longer maintained since February 2023)
- PulsCar home page (read 15 November 2026)
Pages we could not read, and did not get around: NOCO's website (access refused); the product pages of Battery Tender, Gooloo, Schumacher and the US Topdon site (requests limited); the Schumacher manuals (not found at the addresses we tried); the DeWalt and Craftsman product pages (no text); a Harbor Freight page (access refused); the CPSC website (access refused; its recall data service was read instead); test pages from Consumer Reports, Popular Mechanics, Car and Driver and Tom's Guide (not found at the addresses we tried).
Prices verified 15 November 2026: this page quotes no jump starter prices. Technical documents verified 15 November 2026. Written by PulsCar, which publishes this guide and sells no jump starters.

