💡 The answer in 60 seconds

Your car's manual decides first, and the manuals do not agree with each other. The federal standard sets DOT 4 higher minimum boiling points than DOT 3: 230 °C against 205 °C dry, 155 °C against 140 °C wet. On mixing the printed answers split: Subaru says to avoid mixing DOT 3 and DOT 4, Kia and the Nissan Rogue 2026 specification table say never to mix different types of fluid, and Motul and TRW print that their fluids mix with other DOT 3 and DOT 4 fluids, Lucas Oil that its DOT 4 is compatible with other glycol-based fluids, while Castrol prints compatibility and adds avoid mixing. Among the 15 car brands whose manuals we read, Toyota (4Runner, Tacoma), Nissan, Infiniti, Mazda (CX-5), Ram and Jeep name DOT 3; General Motors, most Hyundai and Kia manuals and Genesis name DOT 4; Subaru, Honda UK and the Lexus RX specifications table name DOT 3 or DOT 4; Mercedes-Benz names an approval number and MINI's manual has no brake fluid text. DOT 5 silicone fluid is a different fluid and no source we read allows mixing it. PulsCar sells no brake fluid, no brand pays us and we tested none. Brakes are a safety system: If the red brake warning light stays on with the parking brake released, if the level is under the MIN mark, or if the brake pedal feels soft or spongy, sinks toward the floor or travels farther than it used to: stop driving. Pull over safely, switch the engine off and have the car towed. Do not add fluid, and do not drive on.

Which is better, DOT 3 or DOT 4 brake fluid, and does PulsCar have a view? PulsCar has none, and says so before anything else: PulsCar sells no brake fluid and no brake fluid brand pays us; there is no affiliate link on this page. We did not test any brake fluid, so nothing here says that one grade stops better, lasts longer or is safer than the other. What the page does is line up three kinds of document: the federal standard and the SAE abstract pages for J1703 and J1704, what brake fluid makers print about their own DOT 3 and DOT 4 products, and what car makers' owner's manuals name for the car. Where the documents agree, as on DOT 4 carrying the higher minimum boiling points, the page says so. Where they disagree, as on mixing the two grades, it shows each maker's own words and leaves the decision to the manual for your car.

This is the comparison page for the two grades. Our best brake fluid guide covers which bottle to buy, and our when to change brake fluid guide covers the intervals, so neither is repeated here: this page prints no interval and no shopping list. It stays with the pair: what the standard prints for DOT 3 and DOT 4, how makers print them on their own products, which grade the manuals name, and whether the two can be mixed or swapped.

Every figure below names its source, and we read each page on 17 November 2026. 🟢 Official marks the text of a government regulation or the abstract page of a standards body; ⚪ Maker's claim marks a car maker's or a brake fluid maker's own statement about its own vehicles or products, which is a claim, not proof. A trade-press article is named as one and carries no mark. Makers are listed alphabetically, not ranked. No page we read printed a dollar price for brake fluid, so this page prints none; our brake fluid flush cost guide covers what the service costs, our how to check brake fluid guide covers the level check and the top-up rule, and our how to bleed brakes guide covers the steps.

When your car's manual decides, and what 15 car brands print

Which grade does my car's manual name? It depends on the car, and the manuals of one maker can differ from each other. We read owner's manuals, or the maker's online manual pages, of 15 car brands: Chevrolet, Genesis, Honda (the UK online manual), Hyundai, Infiniti, Jeep, Kia, Lexus, Mazda, Mercedes-Benz, MINI, Nissan, Ram, Subaru and Toyota. Thirteen of them name a grade for at least one model; Mercedes-Benz prints an approval number and no DOT grade, and MINI's Countryman manual contains no brake fluid text at all. Ford's manual site refused access or did not load, so nothing on this page is a statement about Ford. The grid shows what each prints, alphabetically by maker, with the model and market where the document says them.

Chevrolet (Equinox 2026, Equinox EV 2026, Silverado 1500 2025, Silverado EV 2025, US): "GM approved DOT 4 brake fluid", and "Use only GM approved DOT 4 brake fluid from a clean, sealed container." The Equinox and Silverado manuals add "The wrong or contaminated brake fluid could result in damage to the brake system. This could result in the loss of braking leading to a possible injury. Always use the proper GM approved brake fluid."
⚪ DOT 4
Genesis (GV70 2023, US): "Use only hydraulic brake fluid conforming to DOT 4 specification."; the specifications table prints "SAE J1704 DOT0-4LV, FMVSS116 DOT4, ISO4925 CLASS-6" (the "DOT0-4LV" is as printed).
⚪ DOT 4, LV, Class 6
Honda (Prelude 2026 and Super-N 2026, UK online manual): "Specified fluid: Brake Fluid with DOT 3 or DOT 4", and "Brake fluid marked DOT 5 is not compatible with your vehicle's braking system and can cause extensive damage." The Honda US manuals did not load for us.
⚪ DOT 3 or DOT 4
Hyundai (Elantra 2023, Elantra Hybrid 2023, IONIQ 5 2023, Santa Fe 2023, Tucson Hybrid 2022, US): "Use only hydraulic brake fluid conforming to DOT 4 specification."; the Elantra table's footnote reads "(Standard : SAE J1704 DOT-4 LV, ISO4925 CLASS-6 and FMVSS 116 DOT-4)". The Nexo 2023 manual prints DOT-4LV in its capacities table and "Use only hydraulic brake fluid conforming to DOT 3 or DOT 4 specification." in its maintenance text.
⚪ DOT 4 (Nexo: both)
Infiniti (QX60 2025, US): the specification table prints "Genuine NISSAN Super Heavy Duty Brake Fluid or equivalent DOT 3".
⚪ DOT 3
Jeep (Wrangler 2027, US/Canada edition): "We recommend using Mopar® DOT 3 Brake Fluid, SAE J1703."
⚪ DOT 3
Kia (CL4 2026, LQ2 2027 and LQ2AH 2027 pages, US): "Only use hydraulic brake fluid that conforms to DOT 4 specifications." The MQ4KH 2023 lubricants table prints "DOT 4". The CL4 lubricants table prints "SAE J1704 DOT-4 LV, ISO4925 CLASS-6, FMVSS116 DOT-4". The SK3 2024 page prints a different line: "(Classification :SAE J1703, FMVSS116 DOT-3 or DOT-4)".
⚪ DOT 4; SK3: either
Lexus (RX350 and RX350L, OM0E088U, US/Canada edition): the maintenance step prints "FMVSS No.116 DOT 3 or SAE J1703 brake fluid"; the specifications table prints that line and also "FMVSS No. 116 DOT 4 or SAE J1704".
⚪ DOT 3; table: both
Mazda (CX-5 2021, US): the capacities table prints "SAE J1703 or FMVSS116 DOT-3". The CX-90 PHEV 2024 manual prints "Mazda Genuine Brake Fluid or equivalent" and no DOT grade.
⚪ DOT 3; CX-90: no grade
Mercedes-Benz (C-Class 2022, GLE 2022, EQS 2022, US): "Only use a brake fluid approved by MercedesBenz according to MB-Freigabe or MB-Approval 331.0." No DOT grade is printed.
⚪ Approval number
MINI (Countryman 2025, US): the manual we read says nothing about brake fluid.
⚪ Nothing printed
Nissan (Rogue 2023 and 2026, Frontier 2023, LEAF 2026, Ariya 2025, US): "add Genuine NISSAN Super Heavy Duty Brake Fluid or equivalent DOT 3 fluid up to the MAX line".
⚪ DOT 3
Ram (1500 2026 and 2027, US/Canada edition): "We recommend using Mopar® DOT 3 Brake Fluid, SAE J1703."
⚪ DOT 3
Subaru (Outback and Legacy manuals MSA5M2204A, copyright 2021, and MSA5M2403A, edited 2022, US; the text we read prints no model year): the fluids table prints "FMVSS No. 116, DOT 3 or DOT 4". The 2016 BRZ quick reference guide prints "fresh DOT 3 or 4 brake fluid".
⚪ DOT 3 or DOT 4
Toyota (4Runner OM35A83U and Tacoma 2015, US/Canada edition): "FMVSS No.116 DOT 3 or SAE J1703 brake fluid". The RAV4 Hybrid manuals print two lines side by side, "FMVSS No.116 DOT 3 or SAE J1703" and "FMVSS No.116 DOT 4 or SAE J1704".
⚪ DOT 3; RAV4 Hybrid: both

Read the grid for what it says and what it does not. The same standard vocabulary is used for different answers: Toyota's 4Runner and Tacoma, Nissan, Infiniti, Mazda's CX-5, Ram and Jeep print DOT 3 only; General Motors, most Hyundai manuals, Genesis and most Kia pages print DOT 4 only; Subaru, Honda UK, Kia's SK3 page and Toyota's RAV4 Hybrid print DOT 3 or DOT 4. Two manuals disagree with themselves, and we say so rather than choose: the Hyundai Nexo 2023 capacities table says DOT-4LV while its maintenance text says DOT 3 or DOT 4, and the Lexus RX manual's maintenance step names DOT 3 while its specifications table lists both. The Kia SK3 2024 and CL4 2026 pages name different grades. A neighbour's car is not a source.

Several lines name a maker's product or approval rather than a bare grade: General Motors says GM approved, Nissan and Infiniti say Genuine NISSAN Super Heavy Duty Brake Fluid or equivalent DOT 3, and Mercedes-Benz an approval number. For those cars the letters DOT alone are not the whole instruction. Our advice: copy the whole line from the manual, with every standard number it prints, and read it against the whole line on the bottle.

The difference between DOT 3 and DOT 4: what the federal standard prints

What does the standard itself say? The US rule is Federal Motor Vehicle Safety Standard No. 116, in the Code of Federal Regulations as 49 CFR 571.116. Its stated purpose is "to reduce failures in the hydraulic braking systems of motor vehicles which may occur because of the manufacture or use of improper or contaminated fluid." 🟢 Its section S5.3 says each passenger car, multipurpose passenger vehicle, truck, bus, trailer and motorcycle with a hydraulic brake system must be equipped with fluid manufactured and packaged in conformity with the standard. It specifies three grades, DOT 3, DOT 4 and DOT 5, and the grid shows the numbers it prints for each. The standard states them as minimums or maximums for a fluid tested by its own procedures.

Equilibrium reflux boiling point, dry (S5.1.1): not less than 205 °C (401 °F) for DOT 3, 230 °C (446 °F) for DOT 4, 260 °C (500 °F) for DOT 5.
🟢 FMVSS 116
Wet equilibrium reflux boiling point (S5.1.2): not less than 140 °C (284 °F) for DOT 3, 155 °C (311 °F) for DOT 4, 180 °C (356 °F) for DOT 5. The eCFR text prints a stray "1" in front of the DOT 5 value, and we read it as 180 °C.
🟢 FMVSS 116
Kinematic viscosity (S5.1.3): neither less than 1.5 mm²/s at 100 °C (212 °F) nor more than 1,500 mm²/s at minus 40 °C for DOT 3, 1,800 mm²/s for DOT 4, 900 mm²/s for DOT 5.
🟢 FMVSS 116
pH (S5.1.4): not less than 7.0 nor more than 11.5, except DOT 5 silicone fluid.
🟢 FMVSS 116
Low-temperature fluidity (S5.1.7, Table II): after 144 hours at minus 40 °C the air bubble must travel to the top of the sample in no more than 10 seconds, and after 6 hours at minus 50 °C in no more than 35 seconds; the table makes no difference between grades.
🟢 FMVSS 116
Colour (S5.1.14): "DOT 3, DOT 4, and DOT 5.1 non-SBBF—colorless to amber"; "DOT 5 SBBF—purple."
🟢 FMVSS 116

Two things follow from the grid, and both are printed in the standard. First, DOT 4 has higher minimum boiling points than DOT 3, dry and wet, and a higher viscosity ceiling at minus 40 °C: the DOT 4 limits are 25 °C higher dry and 15 °C higher wet, and the DOT 4 viscosity ceiling is 1,800 against 1,500. Second, the standard has no LV grade, no DOT 6 and no DOT 7: its section S5 says it specifies requirements for "DOT 3, DOT 4 and DOT 5 brake fluids", and it treats DOT 5.1 as a labelling distinction within the DOT 5 grade. What the standard does not print is a rule about which car takes which grade, and no sentence about mixing grades in a car; the nearest it comes is the warning that every packaged DOT fluid must carry, "FOLLOW VEHICLE MANUFACTURER'S RECOMMENDATIONS WHEN ADDING BRAKE FLUID." 🟢

The standard also says what its tests are not. The compatibility requirement in S5.1.10, tested under S6.10, mixes the fluid under test with an equal volume of a reference Compatibility Fluid and looks for sludge, sediment, crystals and separation; the standard calls it "an indication of the compatibility of the test fluid with other motor vehicle brake fluids at both high and low temperatures." 🟢 That is a laboratory test against one reference fluid. It is not a statement that a DOT 3 fluid may be mixed with a DOT 4 fluid in a given car, and we read no sentence in the standard that says so.

Dry and wet: what the two boiling points measure

Which boiling point matters, dry or wet? Both are printed, for different states of the fluid. The dry figure is measured on the fluid itself: 60 millilitres are boiled under reflux in a flask, and the average temperature of the boiling fluid at the end of the reflux period is the equilibrium reflux boiling point, or ERBP. 🟢 The wet figure is measured after the fluid has been humidified in a laboratory: the sample sits in a desiccator in an oven held at 50 °C (122 °F) until a reference fluid in the same desiccator reaches "3.70 ±0.05 percent by weight" water, after which the sample's water content and ERBP are measured. 🟢 So the standard's wet figure is a laboratory state with a stated water content, not a prediction for any particular car or year.

The brake fluid makers print the same idea in plain words, and their numbers for the wet state differ. Motul prints "The wet boiling point is measured after moistening the product with 3% water in order to be representative of the state of the fluid after 1 year of use." ⚪ Castrol's Australian page says a wet boiling point is the temperature at which a fluid begins to boil "after it has absorbed 3.7% Water by volume (equates roughly to 2 years service)". ⚪ Hella and Liqui Moly print 3.5 percent water. ⚪ Those are three different water figures, two of them tied to a time, and none is a rule for your car: the standard does not tie its wet condition to a number of months.

Why do the makers bring water into it at all? Because the fluid takes it up from the air. ATE prints "Brake fluids are hygroscopic. This means that over time they absorb water." and goes on to say that because braking creates high temperatures, in extreme cases the liquid can boil, and "Compressible steam bubbles form in the brake lines as a result." ⚪ The car makers print the same warning. Toyota's 4Runner and RAV4 Hybrid manuals say "Brake fluid can absorb moisture from the air. Excess moisture in the brake fluid can cause a dangerous loss of braking efficiency. Use only newly opened brake fluid." ⚪ Subaru's say "Brake fluid absorbs moisture from the air. Any absorbed moisture can cause a dangerous loss of braking performance." ⚪ The Mercedes-Benz C-Class manual says "The brake fluid constantly absorbs moisture from the air. This lowers the boiling point of the brake fluid." ⚪ Ram's and Jeep's manuals say that brake fluid in an open container absorbs moisture from the air, "resulting in a lower boiling point" and possible "sudden brake failure." ⚪ This applies to both grades. Nothing we read says DOT 3 or DOT 4 is the one that avoids the problem; how often to change the fluid is on our when to change brake fluid guide.

Same grade, different numbers: what makers print on their own products

If two bottles both say DOT 4, are they the same? They meet the same minimums, and the makers print different figures for their own products. The grid sets the figures as each maker prints them, alphabetically, for its DOT 3 and DOT 4 products where it prints both. These are the makers' own numbers, some marked minimum and some marked typical, and they are not the standard's numbers. Wet and dry are as the page prints them, in the unit the page uses.

ATE (brochure of 2013; technical data sheets TD 006 and TD 007 of 12.2017): the brochure prints a DOT 3 fluid at 245 °C minimum boiling point, 150 °C minimum wet boiling point and 1,500 mm²/s at minus 40 °C, and a DOT 4 fluid (SL) at 260 °C, 165 °C and 1,400 mm²/s. TD 006 prints its DOT 4 TYP 200 at "Boiling point min. 280° C /536° F; Wet boiling point min. 198° C / 388,4° F" and a maximum of 1,400 mm²/s at minus 40 °C. TD 007 prints its DOT 4 SL.6 at minimum 265 °C and 175 °C and a maximum of 700 mm²/s.
⚪ Maker's figures
Bosch (brochure 2022; ESI6 flyer 2021): the 2022 brochure prints its DOT 4 at 230 °C or more dry, 155 °C or more wet and 1500 mm²/s or less at minus 40 °C; the ESI6 flyer table prints for the DOT 3 and DOT 4 columns 401 and 446 °F dry, 284 and 311 °F wet, 1500 and 1800 mm²/s. The brochure's 1500 is Bosch's product; the flyer's 1800 is the DOT 4 grade column.
⚪ Maker's figures
Brembo (US product page): a table sets Brembo's DOT 3 at 215 °C or more dry, 140 °C or more wet and 1500 cSt maximum, against a base requirement of 205 °C, 140 °C and 1500 cSt; and its DOT 4 class 4 at 245 °C, 157 °C and 1500 cSt, against 230 °C, 155 °C and 1800 cSt maximum.
⚪ Maker's figures
Castrol (DOT 4 product data sheet of 19 July 2018, UK): typical ERBP 260 °C, wet ERBP 165 °C and 1200 mm²/s kinematic viscosity at minus 40 °C. The sheet says the fluid "far exceeds the requirements of the SAE J1703, SAE J1704, FMVSS 116 DOT 4, ISO 4925 and Jis K 2233 specifications."
⚪ Maker's figures
Hella (technical page, parts maker): a table of minimums with Hella's own test results in brackets: dry boiling point over 205 °C (229) for DOT 3 and over 230 °C (268) for DOT 4; wet over 140 °C (149) and over 155 °C (163); viscosity at minus 40 °C under 1500 (1200) and under 1800 (1315).
⚪ Maker's figures
Lucas Oil (product data sheets, last updated 2/9/2026): DOT 3 typical dry 478 °F and wet 339 °F, 1,179 cSt at minus 40 °C; DOT 4 typical dry 476 °F and wet 325 °F, 842 cSt.
⚪ Maker's figures
Motul (sheets dated 10/17 and 01/22): DOT 4 typical dry 257 °C / 494 °F, wet 162 °C / 323 °F, 1288 mm²/s; the DOT 3 and 4 sheet prints typical dry 245 °C / 473 °F, wet 158 °C / 316 °F, 1,350 mm²/s.
⚪ Maker's figures
Prestone (12 fl oz label, Lowe's-hosted): a DOT 3 label prints "DOT 3 460° F Dry Boil Point for Extended Fluid Life and Added Margin of Safety" and "Minimum Wet Boiling Point 284°F (140°C)."
⚪ Maker's figures
TRW (brochure): DOT 3 spec 205 °C dry, 140 °C wet, 1500 mm²/s maximum against TRW 240 °C, 150 °C, 1270; DOT 4 spec 230 °C, 155 °C, 1800 against TRW 270 °C, 163 °C, 1315.
⚪ Maker's figures
Valvoline Australia (DOT 3 sheet effective 04-09-2021, Super Performance DOT 4 sheet of 04-09-2021): DOT 3 ERBP 230 minimum, wet ERBP 140 minimum, 1500 maximum at minus 40 °C; DOT 4 ERBP 280 minimum, wet 180 minimum, 1260 at minus 40 °C. The sheets say the figures apply to products made in Australia.
⚪ Maker's figures

How should a reader use the grid? Two points the makers' own pages support. A figure marked typical, such as Castrol's, Lucas Oil's and Motul's, describes that product, while a figure marked minimum is the maker's stated floor for it. Neither is the standard's figure. Read beside the standard, the grid shows that "meets DOT 4" tells you a product reached the standard's floor, not where it sits above it. Our advice: do not choose a grade by the highest figure on any one bottle.

What SAE and ISO print, and what LV and Class 6 mean

Is the DOT grade the only standard on the bottle? No. Bottles also carry the SAE and ISO numbers, and the manuals for some cars name them. SAE International's page for SAE J1703 says the standard "covers motor vehicle brake fluids of the nonpetroleum type, based upon glycols, glycol ethers, and appropriate inhibitors" for any motor vehicle such as a passenger car, truck, bus or trailer, and adds "These fluids are not intended for use under arctic conditions." 🟢 The page for SAE J1704 covers fluids based on "glycols, glycol ethers, borates of glycol ethers, and appropriate inhibitors". 🟢 We could read only these abstract pages, not the standards; SAE's abstract for J1707, on servicing these fluids, says "Vehicle manufacturer's recommendations should always be followed." 🟢 Toyota's RAV4 Hybrid manuals print the pair as matching sets, DOT 3 with J1703 and DOT 4 with J1704, while Mazda, Ram and the Jeep Wrangler 2027 manual print only J1703 and Hyundai, Genesis and Kia's CL4 page print J1704 beside DOT 4.

The International Organization for Standardization has its own standard, ISO 4925, with classes. We could not read the ISO text itself. What we can report is how the makers print it. ATE prints ISO 4925 Class 3 beside its DOT 3 fluid, Class 4 beside its DOT 4 fluids and Class 6 for its SL.6, which it calls a low-viscosity fluid; Castrol and Liqui Moly print Class 3 for a DOT 3 fluid; Castrol, Pentosin and Valvoline Australia print Class 4 for DOT 4 products; and Brembo, ATE and Liqui Moly, among others, tie Class 6 to a low-viscosity DOT 4, while Motul, Mobil and Comma list Classes 3, 4 and 6 together for theirs. ⚪ ATE's data sheet puts the cold viscosity at "max. 700 mm²/s which is approximately half that of many other commercially available DOT 4 fluids", which it ties to "ISO specification 4925 for brake fluids with low viscosity at low temperatures (class 6)". ⚪ Brembo's table prints a 750 cSt limit for its DOT 4 LV class 6, against 1500 for its DOT 4 class 4. ⚪

Where does that leave a car whose manual says DOT 4 LV? Hyundai's, Genesis's and some Kia manuals print DOT 4 LV beside ISO 4925 Class 6 and FMVSS 116 DOT 4 for the car, and the Elantra's own footnote spells out "SAE J1704 DOT-4 LV, ISO4925 CLASS-6 and FMVSS 116 DOT-4". ⚪ A trade article in Vehicle Service Pros of 7 December 2022, by Kevin McCartney, states that any Class 6 fluid also meets DOT 4 but most DOT 4 fluids do not meet Class 6, and that "low viscosity (LV)" is a marketing term that is not well defined. It is an author's statement, not a standard. ATE says its SL.6 "replaces Super DOT 4", and Pentosin's sheet lists a "SUPER DOT 4" at ISO Class 4 beside a separate "DOT 4 LV" at Class 6, so the labels around DOT 4 do not mean the same across brands. ⚪ Our advice: if the manual prints LV or Class 6, treat that as part of the grade, and ask what the bottle prints for ISO 4925.

Can DOT 3 and DOT 4 be mixed? Car makers first

Can I mix DOT 3 and DOT 4 brake fluid? Nobody prints one answer, so this page prints each one. Start with the car makers, because the manual is the car maker's own instruction. Of the manuals we read, only three makers' say anything about mixing: Subaru's names DOT 3 and DOT 4, and Kia's and Nissan's (Rogue 2026) say never to mix different types of fluid. The grid lists every one we found, alphabetically, with the manual and market.

Chevrolet (Equinox 2026, Silverado 1500 2025, US): "Always use the proper GM approved brake fluid." The same warning says wrong or contaminated brake fluid "could result in damage to the brake system" and in a loss of braking. No sentence about mixing grades.
⚪ Use the approved fluid
Honda (Prelude 2026, Super-N 2026, UK): no sentence about mixing DOT 3 with DOT 4; it says "Brake fluid marked DOT 5 is not compatible with your vehicle's braking system and can cause extensive damage."
⚪ DOT 5 not compatible
Hyundai and Genesis (Elantra 2023, IONIQ 5 2023, GV70 2023, US): the Elantra manual says "Don't put in the wrong type of fluid. A few drops of mineralbased oil, such as engine oil in your brake system can damage system parts."; the IONIQ 5 manual says "Do not use the wrong type of brake fluid." and the GV70 manual "Do not use the incorrect type of brake fluid." No sentence about mixing DOT 3 with DOT 4.
⚪ Wrong type named: mineral oil
Kia (CL4 2026, LQ2 2027, LQ2AH 2027, SK3 2024, MQ4KH 2023, US): "Never mix different types of fluid." The SK3 2024 page, which names "DOT-3 or DOT-4" for the car, prints the same sentence.
⚪ Never mix types
Nissan and Infiniti (Rogue 2026, LEAF 2026, Ariya 2025, US; the Frontier 2023 and QX60 2025 print the warning without the comma): "Use only new fluid from a sealed container. Old, inferior or contaminated fluid may damage the brake system. The use of improper fluids can damage the brake system, and affect the vehicle's stopping ability." The Rogue 2026 specifications table adds "Never mix different types of fluids."
⚪ Improper fluids; never mix types
Ram and Jeep (Ram 1500 2026; the Jeep Wrangler 2027 manual prints the warning with small word changes, US/Canada edition): "Use only manufacturer's recommended brake fluid. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance."
⚪ Use only the recommended fluid
Subaru (Outback and Legacy manuals MSA5M2204A, copyright 2021, and MSA5M2403A, edited 2022, US; the text we read prints no model year): "Never use different brands of brake fluid together. Also, avoid mixing DOT 3 and DOT 4 brake fluids even if they are the same brand."
⚪ Avoid mixing DOT 3 and DOT 4
Toyota and Lexus (4Runner, Tacoma 2015, RAV4 Hybrid, RX): no sentence about mixing grades or about DOT 5 in the manuals we read.
⚪ No mixing sentence

Two of these lines matter for the question as asked. Subaru names both grades for the car, DOT 3 or DOT 4, and in the same manual tells the owner to avoid mixing them, even within one brand. Kia's SK3 page names both grades as well and says never to mix different types of fluid. So a manual that allows either grade is not a manual that allows a blend of the two. Our advice, labelled as ours: where your manual allows both grades, choose one for a fill and keep to it, and where it says to avoid mixing, a flush and refill with one grade keeps to one grade, while topping up with the other grade mixes the two. The manuals do not say how much of the other grade is too much, and we read no maker that does.

Toyota's, Mazda's, Hyundai's and General Motors' manuals say nothing about mixing grades, and silence is neither permission nor a ban. Hyundai's and General Motors' manuals print that the wrong fluid can damage the system; Toyota's and Mazda's name the specified fluid.

Can DOT 3 and DOT 4 be mixed? What the fluid makers print

What do the brake fluid makers say about mixing the two grades? Most print that their own fluid is compatible with the neighbouring grade. They do not all say the same, and the sentences carry conditions. The grid gives them alphabetically, each as printed, for the product named.

ATE: SL.6 (data sheet TD 007): "The ATE brake fluid SL.6 can also be mixed with other brake fluids which meet the specifications ISO 4925 Class 6, DOT 5.1 or DOT 4. However, the optimum ESP functionality, also at very low temperatures, is best ensured with fluids meeting the requirements of the specification ISO 4925 Class 6." SecuBrake: "Miscible with DOT 3, DOT 4 and DOT 5.1; replacement for DOT 3, rubber compatibility ensured - except at extremely low sub-zero temperatures (lower viscosity at –40 °C)".
⚪ Maker's statement
Bosch: the ESI6 flyer says "Use with DOT 3, DOT 4, or DOT 5.1" and "Coverage excludes DOT 5 silicone based brake fluid which is limited to military and racing applications". The range brochure carries the footnote "Not suitable for mineral oil or silicone based systems."
⚪ Maker's statement
Castrol: the DOT 4 data sheet (UK, 2018) says the fluid "is fully compatible with other fluids meeting FMVSS 116 DOT3 and DOT4 however, in order to maintain the superior performance characteristics of Castrol Brake Fluid DOT4, avoid mixing with other brake fluids products." Castrol's Australian page says its DOT 4 is "Compatible with all other brake fluids that meet either DOT 3 or DOT 4 Specification." Its Australian DOT 3 page says "Fully compatible with other brake fluids meeting FMVSS 116 DOT 3, DOT 4."
⚪ Maker's statement
Comma and Mobil (data sheets for DOT 4 ESP, UK): Mobil "Can be mixed safely with other DOT 3 and DOT 4 fluids."; Comma "Can be mixed safely with DOT 4 fluids".
⚪ Maker's statement
Liqui Moly (technical information sheet, 11/2018): "DOT 3 ... should not be mixed with brake fluids of other standards, as the fluid with DOT 4 is much more aggressive and rubber seals in DOT 3 brake systems can swell as a result, which in the worst case can lead to failure of the brake system." The sheet says another standard can be problematic: "If the standard is too low, the boiling point may be too low and cause problems. If the standard is too high, seals and other materials may be attacked by the additives."
⚪ Maker's statement
Lucas Oil (data sheets, 2026): DOT 3 "Compatible with all brake system rubber components and other DOT 3 Brake Fluids." DOT 4 "Compatible with all brake system rubber components and other DOT 4 or DOT 3 Brake Fluids."
⚪ Maker's statement
Motul (four sheets, 2017 to 2024): "Mixable with DOT 3, DOT 4 and DOT 5.1 NON SILICONE BASE products." and "Do not mix with silicone (DOT 5 silicone base) or mineral base" fluids (LHM).
⚪ Maker's statement
Prestone (DOT 3 label): "Safe to mix with any DOT 3 brake fluid."
⚪ Maker's statement
TRW (brochure): "Our conventional DOT fluids will also mix safely with all other fluids conforming to DOT 3, DOT 4 and DOT 5.1."
⚪ Maker's statement

The grid shows the split plainly. One group says its fluid is compatible with the other glycol grades: ATE, Mobil, Motul and TRW, Castrol with a caution, and Lucas Oil's DOT 4; Comma and Prestone speak of one grade only. Bosch's sentence is a statement of use, not of mixing. Even inside that group the sentences carry conditions: ATE says the optimum ESP functionality at very low temperatures is best ensured with Class 6 fluid, and Castrol says to avoid mixing. Liqui Moly's technical sheet says the opposite for DOT 3, and gives a reason: that DOT 4 is more aggressive and rubber seals in a DOT 3 system can swell. Liqui Moly's DOT 4 LV page adds that "optimum product performance is only possible when the product is used unmixed", and its 4-in-1 page says "Optimum effect only in unmixed condition." ⚪ Where a car maker says to avoid mixing, as Subaru does, the fluid makers' sentences about compatibility describe their own products. They do not override the car's manual.

What the standard adds is only the laboratory compatibility test described above. Our reading, labelled as ours: when a bottle says it is compatible with another grade, that describes the maker's formula and the maker's view of the risk, not your car's rubber parts, and the car maker's statement is the one that applies.

Can I mix DOT 3 and DOT 4 brake fluid, and what does this PulsCar guide conclude? It concludes nothing for your car, because the documents split. Subaru's tells the owner to avoid mixing DOT 3 and DOT 4, and Kia's and the Nissan Rogue 2026 manuals say never to mix different types of fluid. The fluid makers' sentences describe their own products: Motul, TRW, Mobil and ATE print that their fluids mix with fluids of the neighbouring grades, Castrol adds avoid mixing, and Liqui Moly's technical sheet says a DOT 3 fluid should not be mixed with other standards. The federal standard prints a laboratory compatibility test against a reference fluid and the warning to follow the vehicle manufacturer's recommendations. No document we read allows DOT 5 silicone fluid to be mixed with them. Our advice: your manual's line is the instruction, and the dealer's answer in writing is the check. This PulsCar guide recommends no grade and sells no brake fluid.

Can you use DOT 4 instead of DOT 3, or DOT 3 instead of DOT 4?

Can I use DOT 4 in a car that calls for DOT 3? The documents we read give three kinds of answer, and none of them is "yes for every car". The manuals, first: where a manual names only DOT 3, we found no sentence in it that allows DOT 4. That covers Toyota's 4Runner and Tacoma, Nissan's Rogue, Frontier, LEAF and Ariya, Infiniti's QX60, Mazda's CX-5 and the Ram and Jeep manuals, and it is a finding about the pages we read, for the models and years we read. Where a manual names DOT 4 only, as General Motors, Hyundai (the Nexo apart), Genesis and most Kia pages do, we found no sentence that allows DOT 3. Where a manual names both, it allows either grade, subject to any mixing sentence.

The fluid makers, second. Several print that their fluid serves either grade: Castrol's Australian page says its DOT 4 is "Suitable for use in all brake fluid systems in cars, motorcycles, and light commercial vehicles (LCV's) requiring either a DOT 3 or DOT 4 product (excluding brake systems where a mineral based fluid is specified)." ⚪ Lucas Oil's DOT 4 sheet says "Automotive and Truck Brake Systems (and hydraulic clutch) which specify DOT 3 or DOT 4 Brake Fluid." ⚪ ATE prints its SecuBrake as a "replacement for DOT 3", with the exception we quoted at extremely low temperatures. ⚪ Against them, Lucas Oil's DOT 3 sheet says "Not recommended for applications requiring DOT 4 Brake Fluid." ⚪ and Liqui Moly warns about the seals in DOT 3 systems. These are statements about the makers' own products, not the car maker's.

The label, third. Every packaged DOT fluid in the US must carry "FOLLOW VEHICLE MANUFACTURER'S RECOMMENDATIONS WHEN ADDING BRAKE FLUID." 🟢 So the one sentence that is printed on every bottle sends the buyer back to the car maker. Our advice: do not change the grade your manual names on your own reading of these pages, and do not accept "it is the same thing" from a counter without the manual's line in hand. Where a manual names one grade and a fluid maker says another is compatible, the manual's line is the instruction. Ram's manual adds that the proper type for the vehicle is "also identified on the original factory installed hydraulic master cylinder reservoir." ⚪ Our best brake fluid guide covers how to read a bottle in the shop.

DOT 5 is not DOT 5.1: the digit changes the fluid

Is DOT 5 the same as DOT 5.1? The standard says no. It defines a silicone-base brake fluid, abbreviated SBBF, as one "which consists of not less than 70 percent by weight of a diorgano polysiloxane", and it requires the label to read DOT 5 SILICONE BASE or DOT 5.1 NON-SILICONE BASE. 🟢 DOT 5 silicone fluid must be purple; the other DOT fluids must be "colorless to amber". 🟢 So the digit after the point separates a silicone fluid from a non-silicone one, and neither is a third kind of DOT 3 or DOT 4.

What do the makers say about silicone fluid and the two grades? Motul prints "Do not mix with silicone (DOT 5 silicone base) or mineral base" fluids (LHM). ⚪ Bosch's flyer says its coverage excludes DOT 5 silicone fluid. ⚪ Brembo's article says "DOT and LHM fluids must never be combined." ⚪ Liqui Moly says of its 4-in-1 fluid "Not suitable for vehicles requiring silicone-based DOT 5 brake fluid." ⚪ Penrite's DOT 3 sheet says "Do not mix this product with SILICONE DOT 5 or MINERAL type brake fluids." ⚪ The car makers: Honda's UK manual says DOT 5 is not compatible, and none of the US manuals we read asks for DOT 5 or silicone fluid. ⚪ The standard also says the mineral-oil fluids that some systems use are a separate thing: its label for hydraulic system mineral oil says it is "NOT COMPATIBLE with the rubber components of brake systems designed for use with DOT brake fluids." 🟢 Hyundai's, Genesis's and Kia's manuals warn that a few drops of mineral-based oil, such as engine oil, can damage the brake system. ⚪

The practical point is about labels: a bottle that says DOT 5 is silicone, and one that says DOT 5.1 is non-silicone. Liqui Moly prints "The DOT 5.1 is a glycol-based fluid compatible with DOT 3 and DOT 4." ⚪ That is a maker's description of its own fluid, and the Subaru, Kia and Honda UK manuals do not name DOT 5.1 for their cars. The trade article we mentioned says DOT 5 "cannot be mixed with any other fluid or substituted for any other fluid"; we found no such sentence in a car maker's manual, and report it only as that article's statement. Our advice: if a bottle says only "DOT 5", put it back unless the manual for your car names it.

Hybrids and electric cars: the same two grades, the same rule

Do hybrids and electric cars use something different? In the manuals that name a grade they name the same two. Toyota's RAV4 Hybrid manuals print both DOT 3 and DOT 4 lines. Hyundai's Elantra Hybrid and Tucson Hybrid, and the IONIQ 5, print DOT 4 LV. Chevrolet's Equinox EV and Silverado EV print GM approved DOT 4. Nissan's LEAF and Ariya print DOT 3 for the brake fluid (Genuine NISSAN Super Heavy Duty Brake Fluid or equivalent), and Mercedes-Benz's EQS prints only its approval number. ⚪ Kia's MQ4KH table, which mentions a PHEV, prints DOT 4. The Hyundai Nexo, a hydrogen car, is the manual that disagrees with itself. We found no hybrid or electric manual that prints a third grade of its own, and no sentence that a hybrid or electric car may use a different grade from the one its manual names. The manuals we read still tell the owner of these cars to use the specified fluid. Whether the fluid needs bleeding by a technician is on our how to bleed brakes guide.

What the bottle must print, and what the cap and colour do not tell you

Does the label tell you the grade? It must, and the standard says how. A packaged DOT fluid has to carry "DOT—MOTOR VEHICLE BRAKE FLUID" with the grade filled in, the minimum wet boiling point in Fahrenheit, the packager's name, the lot and date, and four safety warnings. 🟢 The first is "FOLLOW VEHICLE MANUFACTURER'S RECOMMENDATIONS WHEN ADDING BRAKE FLUID." The second is "KEEP BRAKE FLUID CLEAN AND DRY. Contamination with dirt, water, petroleum products or other materials may result in brake failure or costly repairs." The third says to store it only in its original container, tightly closed to prevent absorption of moisture, and the fourth says not to refill the container or use it for other liquids (not required on containers over 19 litres). 🟢 A container of 177 millilitres or more must have a resealable closure with an inner seal and a tamper-proof feature. 🟢 So the wet boiling point on a standard bottle is a stated minimum, not a measurement of the bottle.

What the label does not print is the rest of the line your manual may name. LV, Class 6, a maker's approval number or a maker's own brand are not in the standard, and a bottle may print them or not. Colour is not a grade marker either: the standard requires DOT 3, DOT 4 and DOT 5.1 fluids to be colorless to amber, and only silicone DOT 5 to be purple. 🟢 TRW prints that its packaging is "colour coded with red for DOT 3, blue for DOT 4 and yellow for DOT 5.1", while ATE sells its DOT 3 fluid as "ATE DOT 3 Blue". ⚪ Blue is the DOT 4 packaging colour at one maker and part of a DOT 3 product's name at another; those are makers' choices for their own products. Our advice: read the words on the bottle, not the colour of the cap or of the liquid.

Handling: paint, skin, eyes, containers and disposal

Do the warnings differ between DOT 3 and DOT 4? The manuals print them for brake fluid in general, and we found none that treats the grades differently. Toyota's manuals say "Take care as brake fluid can harm your hands and eyes and damage painted surfaces." ⚪ Subaru's say "Never let brake fluid contact your eyes because brake fluid can be harmful to your eyes." and "Never splash the brake fluid over painted surfaces or rubber parts." ⚪ Kia's say "Do not allow brake fluid to come into contact with the vehicle's body paint, as it will damage the paint." ⚪ Nissan's manual says brake fluid "is poisonous and should be stored carefully in marked containers out of the reach of children." ⚪ Ram's and Jeep's say overfilling can spill fluid on hot engine parts and cause a fire. ⚪

The printed first aid for the eyes differs. Hyundai's manuals say to flush the eyes with clean water "for at least 15 minutes" and get immediate medical attention. ⚪ Prestone's label says "If in eyes, flush thoroughly with water for at least 20 minutes. Seek immediate medical attention." and prints "WARNING: CAUSES SEVERE EYE IRRITATION. CAUSES SKIN IRRITATION. HARMFUL IF SWALLOWED." ⚪ Where documents differ, our advice is to follow the longer printed time and get medical help.

The safety data sheets add classifications for some DOT 4 fluids. ATE says boric acid esters are the reason "conventional DOT 4 brake fluids are labelled as hazardous substances" and sells a DOT 3/4 fluid without them that carries no GHS classification H361fd, the code for suspected damage to fertility and to the unborn child. ⚪ Castrol's US safety data sheet for its DOT 4 lists "Suspected of damaging the unborn child." ⚪ Both are statements about those makers' products, and we did not read a data sheet for every product. On wiping, Castrol says "Do not wipe" spilled fluid and Mobil and Comma say "Do not rub", rinsing with water. ⚪ On disposal, Liqui Moly says brake fluid is considered hazardous waste and must be disposed of in a proper system, Bosch says to dispose of it at specialized waste-management facilities, and Hyundai's manual says fluid exposed to open air for an extended time should be disposed of properly. ⚪ Our advice: wear gloves and eye protection, wash spills off paint at once, and take old fluid to a collection point.

Where the fluid is not the problem: the stop rule

Can the right grade fix a soft pedal? No, and no document we read says it can. The maker pages we read treat the grade as a specification; the warnings about the pedal and the lamp are about the brake system. ATE describes the worst case of water in the fluid in these words: "In the worst case, the brake pedal drops right down to the floor, and the driver is no longer able to stop the vehicle." ⚪ Honda's UK manual says that if the level is at or below MIN, have a dealer inspect the vehicle for leaks or worn brake pads as soon as possible; its trigger includes a level at MIN, and Honda is the only maker we read that prints "at or below" for the brake fluid level. ⚪ The Mercedes-Benz C-Class message for low fluid level says "Do not continue driving under any circumstances." and adds "Do not add brake fluid." ⚪ General Motors' Equinox 2026 manual says "Do not top off the brake fluid." ⚪ Subaru's manual says that if the vehicle needs frequent refilling there may be a leak. ⚪ Those are the makers' words, and our wording is never softer than any of them:

If the red brake warning light stays on with the parking brake released, if the level is under the MIN mark, or if the brake pedal feels soft or spongy, sinks toward the floor or travels farther than it used to: stop driving. Pull over safely, switch the engine off and have the car towed. Do not add fluid, and do not drive on.

Changing the grade, adding fluid or flushing the system is not a way to test whether the car is safe to drive: it is a job for the technician after the car has been towed.

Questions this page leaves to its neighbours

This page is only the DOT 3 versus DOT 4 question, and each neighbouring question has its own page. How often to change the fluid is on our when to change brake fluid guide, and which bottle to buy is on our best brake fluid guide. What a fluid change costs is on our brake fluid flush cost guide, the level and top-up rules are on our how to check brake fluid guide, and the steps, with the cases where a technician must do it, are on our how to bleed brakes guide.

The traps: three ways a grade decision goes wrong

Trap one: reading DOT 4 as the better DOT 3. The situation: the shelf has both, DOT 4 is the one with the higher numbers, and the bottle looks like the safer choice. What is real: the standard does set higher minimum boiling points for DOT 4, 230 °C dry and 155 °C wet against 205 °C and 140 °C. 🟢 The manuals of Toyota's 4Runner and Tacoma, Nissan, Infiniti, Mazda's CX-5, Ram and Jeep still name DOT 3 and, in the pages we read, no sentence that allows DOT 4. ⚪ Liqui Moly warns that the additives of a higher standard can attack seals in a system built for a lower one. ⚪ The price: a fluid the maker of the car did not name, bought for a number the car was not designed around. The defense: the whole line in your manual, copied down.

Trap two: buying by the largest figure on the label. The situation: a bottle headlines a high dry boiling point or a low viscosity. What is real: the figures on the pages we read are the makers' own, some typical and some minimum, and the standard's figure is a floor. Prestone's DOT 3 label headlines "460° F Dry Boil Point" while its minimum wet boiling point is the DOT 3 figure of 284 °F, and for a car whose manual prints LV or Class 6, the class is a separate line in the manual. The price: paying for a figure the car's manual does not ask for, and missing the line it does. The defense: compare the standard numbers and the manual's classes, then the bottle's whole line.

Trap three: topping up with whatever is in the garage. The situation: the level is low and a bottle of the other grade is open on the shelf. What is real: Subaru says to avoid mixing DOT 3 and DOT 4; Kia and the Nissan Rogue 2026 specification table say never to mix different types; GM says to use only approved DOT 4 from a clean, sealed container; and a low level is itself a printed warning sign: Honda UK sends the owner to a dealer to look for leaks or worn pads, Mazda says a low level is dangerous, and Mercedes-Benz says not to continue driving. The price: an unknown blend in a system that may already have a fault. The defense: treat a level under MIN as the stop rule above, not as a shopping job.

Three typical situations

These are composite scenarios, not individual customers. They are built only from facts earlier on this page.

The Subaru owner with a spare bottle. The manual names DOT 3 or DOT 4 and tells the owner to avoid mixing the two. Our advice: do not ask which grade is better; find out what is in the car, and have the fill done with one grade. If the level is under MIN, the stop rule comes first.

The Ram owner offered DOT 4 at the counter. The Ram manual says "We recommend using Mopar® DOT 3 Brake Fluid, SAE J1703." and "Use only manufacturer's recommended brake fluid." A fluid maker may print that its DOT 4 serves systems requiring DOT 3 or DOT 4, but that is the fluid maker's sentence. Our advice: ask the dealer, and get the answer on the work order, before accepting a different grade.

The Hyundai owner and the "DOT 4" bottle. The manual prints DOT 4 LV, ISO 4925 Class 6 and FMVSS 116 DOT 4 for the car. A bottle labelled DOT 4 and ISO 4925 Class 4 meets the grade word and not the whole line. Our advice: read the bottle's ISO class against the manual's line.

What this page cannot tell you

Does PulsCar recommend a grade or a brand of brake fluid? PulsCar does not, because it sells no brake fluid, tested none, and gets no payment from any maker. The grids above only show what each maker chose to print about its own products, and none of it ranks the makers: a maker that prints figures describes what it sells, and a maker that prints compatibility speaks for its own fluid. If you are choosing between two bottles, the grade and the whole line in your car's manual are the document to compare, together with the label the federal standard requires on every bottle, and, our advice, the work order should name the fluid used, so that you can check it against the manual before you pay for the job. This PulsCar guide is no substitute for the manual, a dealer or a technician, and where the pedal or the warning light is the problem, no choice of fluid is the answer.

We tested no brake fluid, so nothing here says that DOT 3 or DOT 4 stops better, lasts longer or is safer, and every comparison above is a standard's number, a maker's description of its own product, or a car maker's statement about its own vehicles. We read the text of the federal standard and the abstract pages of SAE; we could not read ISO 4925 itself, because ISO's site refused our request, and we could not read the SAE standards behind the abstracts. We read owner's manuals, or the maker's online manual pages, of 15 car brands, plus a Volkswagen UK page, for particular models and years: the Toyota and Lexus files include Canadian copies, the Honda pages are UK pages, and the Volkswagen page is a UK maker page that names a Volkswagen standard and no DOT grade. Honda's US manual pages, Acura's, and the manual sites of Ford, Tesla, Volvo and BMW refused access or did not load, and Cadillac, Chrysler, Dodge, Fiat, Mitsubishi, Rivian and Land Rover manuals we did not find at addresses we could use, so nothing on this page is a statement about them.

No page we read printed a price. Your car, model year and market may differ from every manual here, and your own manual is the document that governs.

Your action plan: before you buy, at the counter, after the job

Before you buy. Find the brake fluid line in your own manual, in the specifications or fluids chapter and in the maintenance chapter, and copy all of it: the DOT grade, any SAE or ISO class, any LV mark and any approval number. General Motors' manuals say the reservoir is filled with GM approved DOT 4 fluid "as indicated on the reservoir cap", and Ram's and Jeep's say the type is also identified on the factory-installed reservoir, so the reservoir is a second place to look. Our advice: use it as a check on the manual's line, not a replacement. If the manual and the reservoir disagree, as in the Hyundai Nexo and Lexus RX manuals, ask a dealer which applies. Do not choose the grade from a friend's car or from a general article, this one included. If the brakes already feel wrong, do not shop first. If the red brake warning light stays on with the parking brake released, if the level is under the MIN mark, or if the brake pedal feels soft or spongy, sinks toward the floor or travels farther than it used to: stop driving. Pull over safely, switch the engine off and have the car towed. Do not add fluid, and do not drive on.

At the counter or the shop. Compare the bottle's whole front label with the manual's line: grade, ISO class, LV or Class 6 if the manual prints it, and a new, sealed container with the packager's lot and date. Ask what is in the car now, and whether the system is being flushed or topped up, because Subaru, Kia and Nissan (Rogue 2026) print rules about mixing. Ask for the fluid name and grade on the work order. For the price of the job and what the quote should show, see our brake fluid flush cost guide; for which bottle suits which job, see our best brake fluid guide.

After the job. Keep the work order and the bottle's label details with the car's records. If the pedal feels different, a warning light comes on or the level falls between two checks, tell the shop at once, and if any sign in the rule below is present, do not drive there. If the red brake warning light stays on with the parking brake released, if the level is under the MIN mark, or if the brake pedal feels soft or spongy, sinks toward the floor or travels farther than it used to: stop driving. Pull over safely, switch the engine off and have the car towed. Do not add fluid, and do not drive on. For when the fluid is next due, see our when to change brake fluid guide.

Sources and documents

Each page below was read on 17 November 2026. Marks: 🟢 government text or the abstract page of a standards body; ⚪ a car maker's or brake fluid maker's own statement; the trade article is named as one. Most maker pages are undated; where a date is printed we give it. Several brake fluid sheets were read as copies hosted on retailers', distributors' or regional sites, and we name the host.

  1. 🟢 Federal brake fluid standard, 49 CFR 571.116 (Cornell LII copy) and the eCFR text
  2. 🟢 SAE International abstract pages: J1703 (October 2025 revision), J1704 (October 2025 revision), J1707 (June 2021)
  3. ⚪ General Motors owner's manuals: Chevrolet Equinox 2026, Equinox EV 2026, Silverado 1500 2025, Silverado EV 2025
  4. ⚪ Hyundai and Genesis owner's manuals: Elantra 2023, Elantra Hybrid 2023, IONIQ 5 2023, Nexo 2023, Santa Fe 2023, Tucson Hybrid 2022, LX3 2026 brake fluid page, Genesis GV70 2023
  5. ⚪ Kia owner's manual pages: CL4 2026 and its lubricants table, LQ2 2027, LQ2AH 2027, MQ4KH 2023, SK3 2024 and its lubricants table
  6. ⚪ Toyota and Lexus: 4Runner manual, Tacoma 2015 manual (toyota.ca copy), RAV4 Hybrid manual OM0R074U and OM0R160U (toyota.ca copy), Lexus RX manual OM0E088U (lexus.ca copy)
  7. ⚪ Nissan and Infiniti: Rogue 2023, Rogue 2026, Frontier 2023, LEAF 2026, Ariya 2025, Infiniti QX60 2025
  8. ⚪ Mazda, Subaru and Honda: Mazda CX-5 2021, Mazda CX-90 PHEV 2024, Subaru Outback and Legacy manual MSA5M2204A and MSA5M2403A, Subaru BRZ 2016 quick reference guide, Honda UK online manuals for the Prelude 2026 and Super-N 2026
  9. ⚪ Ram, Jeep, Mercedes-Benz, MINI and Volkswagen: Ram 1500 2026 and 2027, Jeep Wrangler 2027, Mercedes-Benz C-Class 2022, GLE 2022 and EQS 2022, MINI Countryman 2025, Volkswagen UK brake fluid page
  10. ⚪ ATE: brake fluids flyer 2025, brochure 2013, TD 007 SL.6, TD 006 TYP 200, SecuBrake, brake fluid page; Bosch: brake fluids brochure 2022, ESI6 flyer (a Bosch host with a test-environment name)
  11. ⚪ Brembo: US product page, article on brake fluid; Castrol: Australian brake fluids page, DOT 4 data sheet (copy hosted on a Shopify store), DOT 4 safety data sheet (distributor copy); Comma: DOT 4 ESP data sheet; Hella: brake fluid technical page
  12. ⚪ Liqui Moly: technical information sheet (copy hosted on a distributor's site), brake fluid 4-in-1, DOT 4 LV page; Lucas Oil: DOT 3 data sheet and DOT 4 data sheet; Mobil: DOT 4 ESP data sheet (distributor copy); Motul: DOT 4, DOT 3 and 4, DOT 4 LV, DOT 5.1
  13. ⚪ Penrite: DOT 3 sheet; Pentosin (FUCHS): brake fluids sheet (Slovenian FUCHS site, English sheet); Prestone: DOT 3 label, 12 fl oz (copy hosted by a retailer); TRW: fluid brochure; Valvoline Australia: Heavy Duty DOT 3 and Super Performance DOT 4 product information sheets
  14. Trade press: Vehicle Service Pros, Kevin McCartney, New Class 6 and Class 7 brake fluids are here (7 December 2022)
  15. Our own pages linked above: best brake fluid, when to change brake fluid, brake fluid flush cost, how to check brake fluid, how to bleed brakes
  16. What we could not read, and so did not quote: ISO 4925 itself and ISO's catalogue pages (refused access); the SAE standards behind the abstract pages; Ford, Tesla, Volvo, Honda US, Acura, BMW, Porsche and Audi manual pages (refused access or did not load); Amsoil, the Motorcraft DOT 4 LV page and Mopar and ACDelco pages, and retailer copies of Pentosin sheets (refused access); Pentosin's own site (did not load); Raybestos, Valvoline's US product pages and Wagner's product pages (did not exist at the addresses we used or were not read)

Prices verified: no brake fluid prices are printed on this page; none were printed on the pages read, 17 November 2026 · Technical documents verified: 17 November 2026 · Reviewed quarterly