💡 The answer in 60 seconds

How it works: in several of the sources we read, a repair quote is hours multiplied by an hourly rate plus parts. The FTC says the hours come from one of two places: a flat rate, based on an independent or manufacturer's estimate of the time required, or the actual time the technician worked.
Where flat-rate hours come from: labor guides from Mitchell 1, MOTOR and Chilton, and OEM labor times inside ALLDATA. Mitchell 1, MOTOR and Chilton call their hours estimates, averages or a guide; Mitchell 1 and MOTOR list things the hours leave out, such as rust, broken bolts and unexpected diagnostic hurdles, while Chilton says its times account for rust on older vehicles.
What the law we read asks: a written estimate and your approval before the price grows. Massachusetts alone requires the invoice to say whether hours are actual or flat rate (a posted flat charge is exempt). No statute, regulation or attorney-general page we read uses the words book time or labor guide.
What to ask: please write on the estimate, for each job: the hours, the hourly rate, whether the hours are flat-rate hours or actual hours, and which labor guide the hours come from. A quarrel over hours is never a reason to drive a car whose brakes or steering a shop has called unsafe: approve the safety repair, or get a second written quote the same day and have the car towed to that shop (our advice).

This page answers one question: how do shops calculate labor time, how can you check the hours on a quote, and what should the quote show. Whether a total is too high is the subject of our guide to signs a mechanic is overcharging; disputing a bill after the fact is how to dispute a car repair bill; choosing a shop is how to find an honest mechanic; and the gap between shop types is dealership vs independent mechanic. PulsCar publishes this guide, sells no repairs and no labor guides, and has no affiliate link on this page. Everything below is what the named sources print: labor-guide publishers, vehicle makers, a dealers' trade body, AAA, the FTC, state authorities and a few shops, each read on 13 November 2026. 🟢 Official marks a government text; ⚪ marks a statement by a company, publisher, trade body or shop about its own product or service or about the trade. A price or an hour figure is stated only where a saved page printed it, and every figure carries its source.

Four facts at a glance

Two ways to bill. The FTC: a flat rate "based on an independent or manufacturer's estimate of the time required", or the actual time the technician worked 🟢. AAA says hourly pricing is "much less common" in repair shops
flat rate or clock
Four publishers of the hours. Mitchell 1 (a Snap-on division), MOTOR, Chilton (Gale, part of Cengage Group) and ALLDATA's OEM labor times; Identifix carries MOTOR and Chilton ⚪
4 publishers
What the hours leave out. Mitchell 1 lists diagnosis (unless indicated), rust-frozen parts, broken bolts; MOTOR lists severe corrosion, modifications and unexpected diagnostic hurdles ⚪
estimates, not promises
What the law we read requires. Massachusetts: hours and actual-or-flat designation on the invoice. Pennsylvania: hours and price per hour. Florida: flat or hourly stated on the estimate. California: labor rate not included 🟢
varies by state

Flat rate, book time, actual time: the words as printed

The same idea goes by several names, and the sources we read define them in nearly the same words. The Federal Trade Commission's consumer page on auto repair says "Some shops charge a flat rate for labor on auto repairs. This published rate is based on an independent or manufacturer's estimate of the time required to complete repairs. Others charge on the basis of the actual time the technician worked on the repair." 🟢 The page is dated August 2012 on its face, and it gives the consumer one instruction on the subject: "Before you arrange to have any work performed, ask how the shop prices its work."

AAA's 2026 article on labor rates uses the trade names. "Flat rates are generally calculated using a flat-rate manual or computer program that provides industry-standard times for completing tasks. This is also known as book time or flag time." It adds a definition of the manual itself: "A flat-rate manual is a guidebook or computer program that lists typical vehicle service tasks and the average industry hours for each." About the other method, it says "Hourly-rate pricing is when the technician gets paid for every hour worked on the service. It's much less common in auto repair shops because it doesn't incentivize efficiency, and hourly rates can make for unpredictable customer invoices and labor costs for the shop." That is AAA's description of how shops price their work, in an article for consumers, and it does not give a count of shops.

The National Automobile Dealers Association, a dealers' trade body, has a white paper for dealership service managers (copyright 2010, revised 2014). It names four ways a dealership can price labor; three of the definitions are the plainest we found, and the fourth is job or menu pricing, a labor charge based on what competing facilities charge for similar operations. "Flat-rate hours. Customers pay a uniform hourly charge for an operation's time standard according to a flat-rate manual." "Clock-hour rates. Customers pay an established hourly rate for the actual time spent by each technician working on their vehicles." And a variable option, "Variable labor rates (also called multi-level flat-rate hours). Customers pay one of several hourly rates, based on skill or market category, for an operation's time standard found in a flat-rate manual." ⚪ The section we read does not say which guide the manual is.

One more definition comes from a publisher. Chilton's blog, written by Gale's Chilton staff, says "The time it takes to perform an auto repair or service is called the "flat rate," or labor time." So there are four labels for one thing: flat-rate time, labor time, book time and flag time. In this guide, book hours means the hours a guide prints for a job, flat-rate billing means the shop charges those hours whatever the clock says, and actual-time billing means the shop charges the hours worked.

Who writes the hours: four publishers, in their own words

A flat-rate hour has to come from somewhere, and the pages we read name a few publishers that sell it to shops. What follows is what the publishers' own pages print.

Mitchell 1. Its labor-times page says "Mitchell 1 has been publishing labor estimates for the automotive aftermarket service industry in North America since 1946." On how the hours are made, the page is short: "The estimates in Mitchell 1 labor guides are created through a strictly confidential and proprietary methodology that applies hundreds of years of collective industry experience, time studies and industry interactions." The next sentence says: "As a company policy, Mitchell 1 keeps this methodology confidential and does not share it." It adds a disclaimer we will come back to: "Mitchell 1's labor guides are still estimates that may contain individual errors, and Mitchell 1 is not in any way responsible for individual errors within its labor estimates." A 2023 brochure says the guides were "developed by experienced and highly-skilled editors with extensive automotive expertise, using a methodology proven over time." The pages we read do not say who the editors are or how many technicians are timed. The company's own about page says "Mitchell 1 is a division of Snap-on® Incorporated". ⚪

MOTOR. MOTOR describes its method in a 2025 usage-tips document written for shops. It defines a mechanic labor guide as "a data-driven reference that lists the average labor time required to complete specific automotive repairs on particular vehicles" and says it is "Compiled from studies performed by experienced technicians under controlled conditions". The sentence that explains the numbers is this one: "Publishers gather data by assigning experienced technicians to perform repairs on new vehicles with OEM parts and recommended tools. Each task is repeated several times, the results are averaged and a standard labor time is published." That sentence is written about publishers in general, and the document sits on MOTOR's own site. MOTOR's product page for its Estimated Work Times says the times are "researched using OEM procedures and validated by experts to reflect real-world technician experience and average repair durations." ⚪

Chilton. Today the Chilton name is published by Gale, part of Cengage Group, as ChiltonLibrary; a 2023 Gale flyer describes its estimating tool as using "automaker and Chilton's industry-standard proprietary labor times". The Cengage page for the 2013 edition of the Chilton Labor Guide says "Chilton's editors consider warranty times, component locations, component type, the environment in which technicians' work, the training they receive, and the tools they use when calculating a labor time." and that the guide "provides standard and severe service times, plus OEM warranty times." A MOTOR product catalog uploaded in January 2015 says its Labor Guide Manual has "Labor times based on the original labor time database by the Chilton Company", so the two lines share an ancestor. ⚪

ALLDATA. ALLDATA is the odd one out, because its US pages describe a software feature more than a publication. A February 2026 post on ALLDATA's own blog says the Estimator "uses parts and labor sourced from ALLDATA's OEM repair information", and the menu a shop uses to add a job is called "OEM Labor Times". A support page shows shops how to change catalog times: "Labor Time Adjustments are used to automatically increase or decrease catalog labor times by a percentage or fixed amount, based on a range and account type." None of the US pages we could read defines a labor time or says how the OEM times are set, and ALLDATA's consumer product, ALLDATA DIY, lists "Parts & Labor" among its repair-information types without saying whether it shows hours. ⚪

Identifix. Its Direct-Hit service says it "contains both MOTOR and Chilton guides", and a 2016 page says of the MOTOR guide that "Testing and diagnostic times are also included where applicable." That sentence matters later, because Mitchell 1 says its times leave diagnosis out unless indicated. ⚪

Two things follow from these pages. First, none of the three publishers that describe their hours (Mitchell 1, MOTOR and Chilton) claims its hour is a measurement of your job on your car: they call their figures estimates, averages or a guide. ALLDATA's pages we read do not say. Second, they are commercial products: shops buy them, and Mitchell 1 and ALLDATA both print that a shop can edit the times. We return to both.

The makers' own time allowances

Vehicle makers publish their own labor times too, but for a different purpose, and the open web shows little of it. The Chilton blog explains the purpose: "Automaker labor times set the amount of time they agree to pay their dealers for work on vehicles under warranty. By multiplying the labor time by the hourly labor rate, the OEM calculates a predictable labor cost for each warranty job." It adds "Each automaker conducts time studies to create predetermined labor times for every service and repair, specific to the year, make, and model vehicle, sometimes even for specific components." and "The OEM time assumes the job is conducted flawlessly, with all special tools at hand, no waiting for parts, or other issues." ⚪ That is a publisher's description of makers' practice. We did not find a maker's own table of labor times on the open web; the only maker page we read that describes one is GM's, below.

What a driver can read is the sentence in the warranty booklet. When an owner pays for a warranty repair and the maker reimburses it (in nine of the ten makers, an emergency repair or one under the emissions warranty), ten makers' booklets we read base the labor reimbursement on two things: the maker's own recommended time allowance and an hourly rate that fits your area. Toyota's guide for the 2022 Prius, which says it of repairs covered by warranty that the owner paid for and presents to a dealer, says "warranted labor at a geographically appropriate hourly rate multiplied by Toyota's recommended time allowance for the repair." Subaru's 2024 booklet says the maker is "not obligated to reimburse you ... for labor charges which are higher than SOA's recommended time allowance for the repair multiplied by a labor rate per hour appropriate for your location." Honda, Nissan, Hyundai, Mazda, General Motors (the 2026 Cadillac booklet), FCA US LLC (Ram and Jeep emission-warranty booklets), Kia and Mitsubishi print the same two ingredients in similar words. ⚪

In the reimbursement clauses we read, none prints a table of hours or a worked job, and none defines the words flat rate. They are about reimbursement, not about what a shop may bill you in an ordinary repair. They do show the shape of the system in a line: a time the maker sets, and an hourly rate that depends on where you are.

A word on GM, the only maker whose labor-time guide we found described on a public page. In an April 2021 article for its dealer technicians, GM TechLink describes new add-times in GM's warranty Labor Time Guide for internal repairs of GM automatic transmissions: "Diagnosis Time – 0.0-1.0 hr." and "Cleaning and Inspection – 0.0-2.0 hr."; the diagnosis time may be claimed "depending on actual time to perform diagnosis", and "technician comments and punch times" are required to support the extra time. ⚪ Those are GM's warranty add-times for one family of transmissions, not a price list, but they show how a time guide works: a base time for the job as written, and ranges that depend on what the technician actually did.

What a book hour leaves out, guide by guide

A flat-rate hour describes a job under stated conditions, and the publishers state different ones. Mitchell 1's Estimate Guide FAQ answers a question from a user in the Rust Belt, and the answer is a list. "The conditions can be variable depending on the age of the vehicle, geographic location, etc. Therefore, Mitchell 1 doesn't factor in the following issues into our labor times:" The list reads "Disposal of hazardous materials (unless indicated)", "Diagnosis (unless indicated)", "Machine operations", "Removal of locking lug nuts or wheel covers", "Time necessary to free up parts frozen by rust or corrosion", "Broken bolts, studs, etc.", "Excessive grease, tar and undercoating removal or any other materials that could interfere with operation." and "Cleaning areas of the vehicle which may have been contaminated by failure of the component on which the operation is being performed." ⚪

MOTOR's usage tips say the same kind of thing in fewer words: a standard labor time "does not account for extraordinary circumstances such as severe corrosion, aftermarket modifications or unexpected diagnostic hurdles, which you may need to adjust for in your labor estimates." MOTOR's text defines the standard time as "the vetted number of hours it should take a qualified technician with the proper tools to finish a specific repair." ⚪

Chilton's publisher draws the line in a different place. The Gale blog says the Chilton times "work from OEM benchmarks and account for factors like lack of OEM equipment, tools, training, parts, and experience, as well as particular issues older vehicles have, such as wear, damage, dirt, rust, and modifications." MOTOR's product page says its labor times carry "distinctions between standard and severe duty applications when applicable." ⚪

Put the three side by side and a reader can see why the question "does the book time cover rust?" has no one answer. Mitchell 1 says its times do not factor in time to free rust-frozen parts. The Chilton blog says its times account for rust on older vehicles. MOTOR's usage tips say a standard labor time does not account for severe corrosion. These are three publishers' own statements, one of them about guides in general, on the dates we read them; we did not compare any single job in the three guides, and we have no source that says which guide your shop uses.

The diagnosis line is its own subject, and we give it a section below; here it is enough to say that the publishers' statements on it differ too.

One more exclusion is a deliberate design choice. Mitchell 1's FAQ asks why its times say "DOES NOT include alignment" on many repair estimate times, such as suspension jobs, and answers: "If the labor time allowance to perform the wheel alignment was built into each individual component replacement, the estimated time to replace multiple components within that system would be exceedingly high and inaccurate." So a separate alignment line is how at least one guide is built; the price of the alignment is in our wheel alignment cost guide. ⚪

Why the same job can carry two hours

The sources above show three ways the same job can carry different hours: a guide's own documented procedures, a guide's own editions and, according to one estimating company, differences between publishers.

The first reason is the procedure. Mitchell 1's FAQ, answering a question about why a guide lists two times for the same operation, says "There are occasions where there are two or more acceptable, documented procedures to perform a specific repair on a vehicle." The example it prints is a 2003 Chevrolet Trail Blazer with the 4.2L engine, cylinder head gasket, remove and replace: the original procedure removes the front cover, a later maker bulletin introduced a special tool that avoids that step, and the guide lists both. "The updated procedure, using the special tool, is 9.0 hours versus the original procedure time of 23.1 hours for the 4WD Trailblazer." ⚪ That is the one job in this guide for which a publisher prints the hours of two documented procedures side by side, and it is a 2003 model; we offer it as an illustration of how big the gap between two documented procedures can be, not as a typical difference.

The second reason is the edition. MOTOR's flyers for its Labor Guide Manual in 2014 and 2015 each print, on the back, a table headed "Labor Time Increases", introduced as "a sampling of labor time increases from the previous edition". The rows are MOTOR's own and list only increases, so they say nothing about how many times went down. Four of them show the size of the changes:

Audi A7, 2012-13, fuel filter, renew. 2013 Edition 0.4 hours; 2014 Edition 1.8 hours ⚪
0.4 to 1.8 hours
Chevrolet Camaro, 2010-13, 6.2L, camshaft position sensor, renew. 2013 Edition 0.4; 2014 Edition 2.7 ⚪
0.4 to 2.7 hours
GM pickup, 2007-14, 6.6L, fuel injectors. 2014 Edition 4.8 hours; 2015 Edition 15.7 hours ⚪
4.8 to 15.7 hours
Jeep Liberty, 2002-07, heater core. 2014 Edition 6.0 hours; 2015 Edition 8.0 hours ⚪
6.0 to 8.0 hours

The flyers do not say why each time changed, and they are more than a decade old; we show them only because they are the publisher's own printed proof that the same job's hours move between editions of one guide. A quote that cites last year's book may differ from one that cites this year's, even with the same publisher.

The third reason, from one source, is the publisher. A RepairPal knowledge-base page written for shops, last updated 3 July 2024, says its estimator's labor times come from MOTOR and adds "There can be discrepancies between the two systems in some cases, and in rare cases ours may be the lesser of the 2." The same passage says MOTOR's times are "which more closely aligns with ALLDATA than Mitchell." ⚪

The practical consequence is modest. If a second shop quotes different hours for the same job, that is not by itself proof of a problem: guides, editions and procedures can differ. Ask which guide, and which procedure, the hours come from, and ask for the guide name in writing (the wording is in the section on what a quote should show).

Related jobs: combination times, overlap and add-ons

The second place a quote can differ from a headline book time is the jobs done together. Mitchell 1's term is combination time: "Combination time: additional labor times to be used when performing tasks which are directly related to the original operation and are conveniently done along with it." Its example is "when performing a timing belt R & R, you could replace a number of components in "combination" with the timing belt operation." The pages we read never use the word overlap for Mitchell 1's guide. MOTOR does: its Estimated Work Times product sheet from 2016 says "Optional operations account for overlap", and its 2014 and 2015 Labor Guide Manual flyers say each chapter has "hundreds of individual and overlap mechanical repair operations." ⚪

What these sentences say, in plain words, is that the guides carry their own times for related jobs done together (Mitchell 1: additional labor times; MOTOR: optional operations that account for overlap). The pages do not print how a combination time compares with the separate times, or the rule for any specific pair, and we cannot tell you whether your quote applied one. That is a question for the shop: ask whether the jobs share any removal, and whether the guide's combination time was used.

MOTOR also warns shops against leaving related work off. MOTOR's usage tips say "Related operations—rotor resurfacing, caliper hardware replacement—may be listed separately. Include them to avoid underbilling." and "Swapping a water pump often requires belt removal and coolant replacement. Omitting these additional labor items results in underbilling and rushed technicians." ⚪ Both can be true at once: a guide can carry a combination time for jobs done together, and it can list related operations on separate lines that a shop adds because the guide lists them. A line you do not recognize is a reason to ask what it is for, not proof that the shop padded the bill. For signs that a bill is padded, see our guide on signs a mechanic is overcharging, which covers the red flags; this page covers only the hours.

From hours to dollars: the arithmetic and the rounding

Several of the sources we read describe the same arithmetic. MOTOR's usage tips say each guide entry "assigns a labor hour figure you can multiply by your shop's hourly labor rate to produce a quick, defensible quote." The Chilton blog gives a worked illustration of its own, which is a hypothetical and not a real job: "the labor cost to replace brake pads with a 2-hour labor time at an hourly rate of $130 would be $260." The AAA 2021 magazine column says the same of the customer's side: "Customers are quoted the flat-rate time multiplied by the shop's hourly labor rate". ⚪ So the labor line on a flat-rate quote has two numbers that matter, the hours and the rate, and a quote that shows only the total does not let you check either.

The rate is the shop's own. AAA's 2026 article says "A mechanic's labor rate is influenced by several factors, like wage costs, location, business expenses, regulations and the type of repair shop. You should know that the mechanic who does the work doesn't receive the entire hourly labor rate customers pay." So the hourly rate on a quote covers more than the technician's pay.

With actual-time billing the arithmetic has a different pinch point, which is rounding. One shop page we read, from AGCO Automotive in Baton Rouge, says "We bill for diagnosis, like all work performed by AGCO, by the amount of time spent, or actual time billing. Our service rate is $125.00 per hour and we bill in 1/10 hour increment." ⚪ It then prints a table in which 0.1 hour is $12.50. The page is one shop's, and it does not say what other shops do. Maine's law, which we come back to, requires a shop's posted notice to include a blank for the rounding rule: "We round off the time to the nearest ." That is a state rule printed as a blank, so each shop fills in its own. 🟢 If you are billed by the clock, ask what increment the shop bills in.

A third piece is how a dealership arrives at the rate it calls its own. A 2025 California New Motor Vehicle Board document (protest PR-2803-22, its pages headed "Proposed Decision Following Remand"), in a case about one dealer group's warranty reimbursement, quotes Vehicle Code 3065.2(a)(2): "The franchisee shall calculate its retail labor rate by determining the total charges for labor from the qualified repair orders submitted and dividing that amount by the total number of hours that generated those charges." 🟢 For that warranty purpose, then, a retail labor rate is dollars of labor divided by hours billed. The decision also records that the group "generally priced repairs using retail labor rates between $220/hour and $250/hour, multiplied by time allowances in commercial guides (independent third-party guides)" before 2020, and that for diagnostic-only jobs advisors were instructed to quote "a "flat fee" of $250.00, with a "sold hour" time of .5 hour ($500/hour)." These are findings about one dealer group in a contested case, not about the market. 🟢

Hourly rates printed on dated pages

The printed hourly rates we found are thin and do not agree with each other, which is why we do not give you one number.

AAA, 2026 article on labor rates. The average mechanic labor rate varies "from less than $100 to over $200 per hour"; "Almost half of all auto repair shops price their labor between $120 and $159 per hour", citing the 2025 PartsTech Report ⚪
$120 to $159 (almost half)
MOTOR, 2025 usage tips. "General repair facilities in the United States typically charge $75-$125 per hour, while specialty or high-end dealerships may exceed $150." A publisher's own marketing document ⚪
$75 to $125 (typical)
AAA magazine column, 1 May 2021. A dealer's rate "just under $200"; shop rates "can range from $50 to $220 an hour" ⚪
$50 to $220
AGCO Automotive, Baton Rouge (own page, read 13 Nov 2026). "Our service rate is $125.00 per hour", billed by actual time ⚪
$125.00 per hour
California New Motor Vehicle Board document, 2025. One dealer group "generally priced" repairs at these retail labor rates before 2020, in a contested case 🟢
$220 to $250 (one group)

The AAA 2026 article also prints a table of "average cost of labor" by state, from $211.26 (Michigan) to $281.53 (Connecticut), credited to World Population Review. The table carries no unit and its figures are higher than AAA's own $120 to $159 band, so we do not read it as hourly rates. The article's claim that dealer mechanics "generally cost more than independent mechanics, often by 25 percent or more" is worked through in our dealership vs independent mechanic guide.

Three states print a posting rule for the rate itself, so you can see it before you ask. Connecticut's statute says a shop's sign "shall state: (1) The hourly charge for labor". 🟢 Maine's statute prescribes the notice "WE CHARGE $ PER HOUR FOR LABOR." 🟢 Alaska requires "an authorized dealer" to post "a notice of the authorized dealer's retail labor rate in a place conspicuous to service customers." 🟢 California goes the other way for ordinary repair shops: the Bureau of Automotive Repair says of the labor rate "No, the labor rate is not included in either the estimate or the invoice", with two exceptions: vehicle safety systems inspection stations must post the inspection price, and Smog Check stations must post a list of prices and an hourly labor rate. 🟢 Georgia's consumer page says plainly that "there is no statute in Georgia that requires dealers to publicly post their hourly repair rates." 🟢

Flat rate or actual time: what each does to a bill

The sources describe flat-rate billing as a trade, and it helps to state what each side gets. Chilton's blog states it from the maker's side: "Whether the job actually takes less or more time, the OEM still pays the same labor time." AAA's 2021 column states it from the technician's: "Techs are paid the flat-rate time multiplied by their hourly wage" and "If they do the job faster than the flat-rate time, they'll effectively earn a higher wage. If rookies take longer, they'll earn less. Either way, the customer pays the quoted amount." ⚪ A shop's own page, from Kwik Kar Spring Valley (a blog dated 27 May 2026), puts the same point from the customer's side: "A brake caliper replacement listed at 1.4 hours gets billed as 1.4 hours whether the technician completes it in 50 minutes or 90 minutes." That sentence is the shop's illustration of the method and not a guide's printed time. ⚪

So under flat-rate billing the customer pays the book hours whether the technician is fast or slow. Andy's Automotive and Truck Services, a shop whose July 2022 post breaks down a bill, says "In most cases, a national labor guide determines how long the job should take and how much time to charge the customer for." and that "In some cases, higher mileage vehicles with extensive rust may take longer than "the labor guide" recommended time. And a quality mechanic would make you aware of this potential extra charge ahead of time and get your approval for the repair." ⚪ That is what one shop says a good shop does, and it matches the rules we read on approval.

The sources do not agree on whether flat rate is good for the customer. MOTOR's usage tips, written for shops, call guide hours a way to produce a "defensible quote". Maine's attorney general writes the other way: "Be cautious if a repair shop charges by a flat rate, which could inflate the time usually needed for a repair." 🟢 AAA says of the hourly method that it "doesn't incentivize efficiency, and hourly rates can make for unpredictable customer invoices and labor costs for the shop." We read these as one trade-off: flat rate gives a predictable bill and a possible gap between hours billed and hours worked; actual time ties the bill to the clock and makes the total less predictable. The FTC's advice, to ask how the shop prices its work, fits either method.

What the law we read says about labor on an estimate or invoice

Auto-repair rules are state rules, and they differ a great deal. We read the statute, regulation or attorney-general page of sixteen states: Florida, Massachusetts, Pennsylvania, Maine, Connecticut, Alaska, Illinois (the attorney general's page only), New York, New Jersey, Minnesota, Washington, California, Texas, Colorado, Arizona and Georgia. We could not read Michigan, Virginia, Oregon, Ohio, New Hampshire, Maryland or Wisconsin (the pages were blocked or did not load), so this guide says nothing about them. A few of the texts (Massachusetts, New York and New Jersey regulations) were read on Cornell's Legal Information Institute copy because the state sites refused us; those are marked in the sources. What each prints about how labor is stated differs, and the five most specific are in the grid.

Massachusetts, 940 CMR 5.05(9)(g). The invoice must show the hours, whether they are actual hours or flat-rate hours, the price per hour and the labor total 🟢
hours + actual or flat rate
Pennsylvania, 37 Pa. Code 301.5. The invoice must show the number of hours, the price per hour and the labor total 🟢
hours + price per hour
Florida, s. 559.905. The estimate must state whether the customer is charged a flat rate, an hourly rate or both 🟢
flat or hourly stated
Maine, 29-A MRS 1805 and 1802. A posted notice with the hourly rate and, where flat rates are charged, a flat-rate warning; the same labor rate method in the estimate and the bill 🟢
posted rate, same method
California, BAR "Write It Right". Labor rate not included in the estimate or the invoice; the job and the price for parts and labor are 🟢
rate not included

Massachusetts is the only text we found that makes the shop say both how many hours and what kind. Regulation 940 CMR 5.05 lists what an invoice must contain, and item (g) reads "The number of hours of labor charged for the repair work, a designation of such hours as actual hours worked or flat rate hours, the price charged to the customer for each such hour and the total amount charged to the customer for labor;" There is an exception: if the price is a flat charge for the particular repair that was in a posted schedule of charges when the vehicle was delivered, the shop "need not list the price of each part supplied, the number of hours charged or the charge for each hour of labor." The same regulation calls it an unfair or deceptive act to charge for repairs without the customer's written authorization listing the specific repairs and the total price (it lists alternatives, such as posted charges, a notification where the repairs are not yet known, or a signed waiver), and to go more than $10.00 above the authorized price without telling the customer and getting authorization to continue. 🟢

Pennsylvania asks for the hours and the hourly price but not the kind of hours: the invoice must show "The labor charge for the repair work, setting forth the number of hours, the price charged for each hour and the total amount charged the customer for labor;" with the same sort of exception for a posted single charge. Where the specific repairs or their costs are not known when the vehicle is delivered, the code lists options for the customer, one of which allows repair to be authorized without a price limit "provided the customer is informed of the hourly labor rate prior to commencement of repairs." 🟢

Florida's statute requires a shop to prepare a written estimate when the repair will exceed $150, unless the customer declines it on the statutory form, and one of the items the estimate must contain is "A statement as to whether the customer is being charged according to a flat rate or an hourly rate, or both." The statute does not require the number of hours or the rate to be on the estimate. The Florida Attorney General's own leaflet says $100 where the statute says $150; we print both and take the statute as the law. On overruns, section 559.909 makes it unlawful to charge more than the written estimate plus "$10 or 10 percent, whichever is greater, but not to exceed $50" without the customer's authorization. 🟢

Maine's text is about the method itself. Its notice, to be posted, includes the line "WE CHARGE $ PER HOUR FOR LABOR." and, where the shop also charges flat rates, says "PLEASE ASK US WHETHER WE WILL CHARGE YOU BY THE HOUR OR BY A FLAT RATE. We use the same labor rate method in any estimate we provide and any bill you receive." Section 1802 says a repair facility "shall charge a customer by using the same labor rate per hour and shop supplies calculation as is used in any estimate the repair facility provides." Maine's attorney general tells consumers "Be sure to ask your repair shop the basis for the estimate, including how many hours of work they estimate the repair will take and the hourly labor rate." 🟢

Connecticut wants a sign stating the hourly charge for labor and written authorization with an estimate of the maximum cost of parts and labor; it says nothing about flat rate. Alaska asks only dealers to post a retail labor rate. New Jersey's auto body rule asks the estimate to give the labor charge or "the total number of hours estimated to perform all the requested repairs, together with the hourly labor rate", while its mechanical-repair rule lists alternatives for the estimate, including a not-to-exceed price and a written breakdown of parts and labor. New York's regulation says an estimate on request must contain "the labor charge for each repair together with the costs of each labor charge". 🟢

Minnesota and Washington print the general rule in statute: an estimate that includes labor, and a 110 percent limit unless the customer authorizes more. Minnesota lists "(e) labor charges;" among the estimate's contents, which the shop gives on the customer's request; Washington's attorney general says the invoice should include "the total amount charged for all labor". Colorado's attorney general says a shop may not charge more than the estimate plus ten percent or twenty-five dollars, whichever is less, without consent. Texas, Arizona and Georgia give advice rather than a rule: Texas's page says the initial work order should clearly specify "the work to be done, fees, completion date, terms of payment, and more"; Arizona's says an estimate "should identify the problem to be repaired, the parts needed and the anticipated labor charge"; Georgia's says it "includes the condition to be repaired, the parts needed, and the anticipated labor rate." None of the six says whether labor is flat rate or hourly. 🟢

Illinois's attorney general page says an estimate must include "Method for Calculation of Labor Costs". We could not read the Illinois statute, so we take the attorney general's heading as printed and do not say what the statute itself requires. 🟢

The words the law does not use

No statute, regulation or attorney-general page we read uses the words "book time" or "labor guide". The pages that come closest are Massachusetts (a designation of flat-rate hours) and Florida (flat rate stated) and the Maine notice (flat rate explained to the customer). In practice, a shop that declines to name its guide, or to show you its page, is not necessarily breaking any rule we read; and a shop that names it is doing more than the law we read asks.

It also bears on what to expect in the reverse direction. In states with an overrun rule, the lever you hold is the approval of the number, not the guide. Florida's $10 or 10 percent up to $50, Massachusetts's $10, the 110 percent of Washington and Minnesota and Colorado's 10 percent or $25 whichever is less are all measured against the estimate or the price you authorized. In plain terms, once you have a written estimate with hours and a rate, charges above it, beyond the margins those rules allow, need your authorization first in these states. No source we read says that a bill above the guide's hours is unlawful by itself, and we do not say it. 🟢

California's Bureau of Automotive Repair says an estimate "must contain a description of the specific job and the estimated price for all parts and labor", and that the labor rate is not included; the page does not say a shop may not show it, so you can still ask. The page does not require the rate, but it says an estimate and invoice "should itemize and describe all parts and labor for a specific job in a manner that the customer can easily understand what was purchased." 🟢

Diagnosis: the hours a guide may not cover

The guides were built around repair jobs, and Mitchell 1 lists diagnosis among the things it leaves out, while MOTOR lists unexpected diagnostic hurdles. The sources we read say it in three ways.

The publishers: Mitchell 1 says its times do not factor in "Diagnosis (unless indicated)"; MOTOR's tips list "unexpected diagnostic hurdles"; Identifix says of the MOTOR guide "Testing and diagnostic times are also included where applicable." The makers: GM's technician newsletter describes diagnosis as an add-time of 0.0 to 1.0 hour in GM's warranty Labor Time Guide for internal transmission repairs, to be claimed by actual time and supported with technician comments and punch times, and several of the warranty booklets we read say that for an emergency repair the owner paid for elsewhere, or a repair under the emissions warranty, the maker reimburses diagnosis (Hyundai says "including diagnostic charges", Nissan "including diagnosis"). AAA: "Not all services can be estimated using the flat-rate system. Diagnostic work is a good example because every troubleshooting process is unique." It describes a basic diagnostic charge with a maximum time limit, after which "they will contact you, describe what has been done to that point and ask for more time (and money) to do further diagnosis." ⚪

Three state sources add to this. Florida's estimate rule covers "diagnostic work" by name: the written estimate is to be prepared "before effecting any diagnostic work or repair" when the cost will exceed $150. 🟢 The Texas Attorney General's page lists among practices to watch out for "The shop charges for a computer diagnosis without telling you in advance it was required." 🟢 And Connecticut's posted sign must state "the charge, if any, for a diagnosis." 🟢

Whether diagnosis is a separate line or a book time depends on the shop and the guide: AAA describes a basic charge with a time limit, AGCO bills the clock, Mitchell 1 leaves diagnosis out unless indicated, and Identifix says the MOTOR guide includes it where applicable. The prices of diagnosis are covered in our guide to how much a car diagnostic costs; the question for this page is narrower: is the diagnosis line on your quote billed by the clock, by a flat fee, or by a book time? Ask which, and ask whether the diagnosis fee is credited if you go ahead with the repair. Most of the texts we read do not say whether it is credited; the one rule we read that speaks to it is New Jersey's mechanical-repair rule, which says "No cost of diagnosis which would have been incurred in accomplishing the repair shall be billed twice if the customer elects to have the dealer make the repair". 🟢

What a quote should show about labor

The list below is our own, built from what the publishers, the FTC and the states above print, and it says where each item comes from. A shop is not obliged to give you all of it in the states we read, and we do not say it is. It is the set of lines that lets you, or a second shop, check the hours and the rate without guessing.

  • Each job on its own line, in plain words. The California Bureau of Automotive Repair says an estimate and an invoice should "itemize and describe all parts and labor for a specific job in a manner that the customer can easily understand what was purchased." 🟢
  • The hours for each job, and the hourly rate. Massachusetts and Pennsylvania require both on the invoice; Maine's attorney general says to ask for both. 🟢
  • Whether the hours are flat-rate or actual. Massachusetts requires the designation on the invoice, Florida requires the estimate to say flat rate or hourly or both, and Maine requires the same labor rate method in the estimate and the bill. 🟢
  • Which labor guide, and which edition. No state text we read requires it. The publishers' times differ, and MOTOR's flyers print the same job's hours changing between editions, so the name and edition are what let you compare two quotes on the hours. Kwik Kar tells customers to ask which guide a shop uses.
  • Whether a combination or overlap time was used when two jobs share a teardown. Mitchell 1 defines combination times as additional times for related tasks, and MOTOR says its optional operations account for overlap; neither prints how they compare with separate jobs, so the line is a question, not a verdict.
  • The diagnosis line, separate, and how it is billed: by the clock, by a fixed charge with a time limit, or by a book time; and whether it is credited if you go ahead.
  • The rounding rule, if the shop bills by the clock. AGCO bills in 1/10 hour increments; Maine's notice has a blank for it.
  • The approval line. The FTC says the written estimate "should state that the shop will contact you for approval before they do any work exceeding a specified amount of time or money. State law may require this." and "Make sure you get a signed copy." 🟢

Items marked 🟢 have an official page behind them; the others are questions we think are worth asking, with the sources' own words as the reason.

How to ask for the hours, and what you can and cannot get

The request we suggest is one sentence, and the wording is the same wherever we use it in this guide: please write on the estimate, for each job: the hours, the hourly rate, whether the hours are flat-rate hours or actual hours, and which labor guide the hours come from. It is our wording and not the law's; it combines the FTC's advice to ask how the shop prices its work, Maine's attorney general's advice to ask for the hours and the rate, and the question that a shop page we read tells customers to ask: Kwik Kar says "Ask the shop which labor time guide they use (Mitchell1, Chilton, or All Data are the most common)." and lists the question "What guide time are you using?" followed by "A specific number tied to a named guide". ⚪

What you may not get is the page itself. Mitchell 1 says it "keeps this methodology confidential", and the publishers sell guides to shops (Gale's blog mentions library subscriptions). Prices we saw: the Cengage page for the 2013 Chilton labor guide on CD-ROM lists a price "starting from" $249.95, and ALLDATA's consumer product, ALLDATA DIY, lists a one-year plan at $59.99 (and $19.99 for a month) and names "Parts & Labor" among its repair-information types, without saying whether the labor hours are shown. ⚪ Kwik Kar tells readers to "Check the listed hours against a public labor guide or ask the service advisor to explain the source." We did not find a free public page that prints the guides' hours for your car's job (the free pages we read print a few sample rows only), so for most readers the second half of that sentence is the practical one. MOTOR's usage tips, written for shops, say "Attach the labor guide reference to the repair order so technicians know the expected labor hours. Sharing this data with customers reinforces transparency and builds trust." That is advice to shops from a publisher, not a rule, and it shows what a shop that wants to cooperate can do.

How do you check the hours on a repair quote, and does PulsCar have a tool for it? You ask in writing, and you compare. Please write on the estimate, for each job: the hours, the hourly rate, whether the hours are flat-rate hours or actual hours, and which labor guide the hours come from. No law we read requires all four, and the publishers' guides are sold to shops, so you will rarely see the page itself. A second shop's written quote, with its own hours, rate and guide name, is the check anyone can run, and a gap between the two is a reason to ask both shops a question, not a verdict. PulsCar publishes this guide and sells no repairs or labor guides; its free check listens to an engine for 30 seconds and does not estimate labor, so the written quote and a second shop's quote are the tools here.

Three answers are worth recognizing. A shop that names a guide and shows the hours has told you something you can check against a second quote. A shop that says the hours are actual time has told you to ask for the rate and the rounding. A shop that will not say how it prices leaves you nothing to compare, and the FTC's advice stands: "Before you arrange to have any work performed, ask how the shop prices its work."

When the hours legitimately differ from the book

A shop can have honest reasons to bill more or fewer hours than the headline guide time, and the sources say so in their own words, which is why we do not treat a gap as proof of a problem. Mitchell 1 and MOTOR each list the conditions their times do not cover (rust-frozen parts, broken bolts, severe corrosion, unexpected diagnostic hurdles), and MOTOR writes "which you may need to adjust for in your labor estimates." The publishers' own wording about their numbers is cautious: "still estimates that may contain individual errors" (Mitchell 1), "Standard labor times are averages, not promises" (MOTOR) and "The times are a guide, not an absolute" (Chilton's publisher). ⚪

Shops can also edit the times in the software. Mitchell 1's estimating page says "You can adjust estimates by editing labor times, adding parts, or grouping items." An ALLDATA support page describes "Labor Time Adjustments" that "increase or decrease catalog labor times by a percentage or fixed amount". MOTOR's usage tips say, of shops: "Many shops add a labor matrix or percentage uplift for older vehicles or complex repairs to keep margins intact." ⚪ It is in the publishers' own pages. It means that the number on your quote may be the guide's time, the guide's time adjusted by a rule, or a time the shop typed, and the only way to know is to ask.

Can a shop bill more hours than the labor guide shows, and what does PulsCar say about it? The guides call their hours estimates and averages, shops can edit them, and no source we read says billing above a guide is unlawful; what the rules we read ask is a written estimate and your approval before the price grows. If the hours differ from a guide you have seen, ask for the reason in writing. PulsCar publishes this guide, sells no repairs and has no affiliate link on this page; its free engine-sound check does not estimate labor. A quarrel over hours is never a reason to drive a car whose brakes or steering a shop has called unsafe: approve the safety repair, or get a second written quote the same day and have the car towed to that shop (our advice).

The fairest test, in our reading, is when the reason arrives. Andy's Automotive and Truck Services says of a higher-mileage car with rust that goes past the guide: "a quality mechanic would make you aware of this potential extra charge ahead of time and get your approval for the repair." Approval before extra charges is what the state rules we read ask for. A reason given after the bill is the moment our guide on how to dispute a car repair bill starts from, and we do not repeat its steps.

Where PulsCar fits, and where it does not

This page has no call to action, because PulsCar's free sound check does not bear on a labor quote.

How do shops calculate labor time, and where does PulsCar fit? In several of the sources we read, shops multiply hours by an hourly rate, and the hours come from a flat-rate guide published by Mitchell 1, MOTOR or Chilton, or from the clock. PulsCar publishes this guide, sells no repairs and no labor guides, and has no affiliate link on this page. Its homepage describes a free 30-second engine sound check and says it is "a screening from sound, not a hands-on inspection." ⚪ The free check does not estimate labor, so for the hours and the rate, the questions above and a second written quote are the tools. This page gives no hours for your job and no single rate for the same reason: the sources we read do not support one.

Three traps in a labor line

Trap one: the lump. The situation: a quote shows a single labor total with no hours and no rate. What is real: California's page says the labor rate is not included in the estimate or the invoice, and Florida asks only for a statement of flat rate or hourly. What to do: use the one-sentence request above; a lump cannot be checked against a second quote.

Trap two: comparing unlike hours. The situation: two shops quote different hours for one job. What is real: guides differ by publisher, edition and procedure, one shop may bill flat-rate hours and the other the clock, and a flat fee can be booked as a fraction of an hour. What to do: ask each shop which guide and method, then compare.

Trap three: treating book time as a law. The situation: a customer says the guide shows less, so the bill is illegal. What is real: no source we read says billing above a guide is unlawful, and the publishers call their hours estimates. What to do: ask for the reason in writing; where an overrun rule exists, check whether you approved the extra.

Three typical situations

These are composite scenarios, not individual customers. They are built only from facts already on this page and contain no invented names, hours or amounts.

Scenario 1: two quotes, two guides. Suppose a driver gets two written quotes with different hours for the same repair. The driver asks each shop which guide and which procedure the hours come from. One names a documented procedure that needs a special tool. Lesson: Mitchell 1 prints two documented procedures for the same operation, so the gap may be a procedure, not padding.

Scenario 2: a quote with one labor figure. Suppose a shop in a state where the rate need not be written down hands over a single labor total. The driver asks the shop to write the hours, the rate, flat-rate or actual, and the guide. Lesson: the request is yours to make; the law we read for that state does not make it.

Scenario 3: extra hours mid-job. Suppose a shop that bills by the clock calls to say rust has slowed the job. The driver asks for the extra hours and the rate in writing before saying yes. Lesson: Mitchell 1 and MOTOR list rust and corrosion as things the book hours leave out, and the rules we read ask for approval before the price grows.

What this page cannot tell you

  • How many hours your job takes (our transmission replacement cost guide lists the labor times makers print for that one job). No page we read prints a verified time for a named job on a named car except the examples quoted above (Kwik Kar's example hours are the shop's own illustration), and your car's job sits in an edition of a guide we cannot see.
  • Which guide, edition or method your shop uses, or whether it edited the time.
  • Whether your shop's hourly rate is fair. The pages we read disagree, and the shop's own rate is on its estimate.
  • The law of seven states we could not read (Michigan, Virginia, Oregon, Ohio, New Hampshire, Maryland, Wisconsin), and the Illinois statute, which we did not read.
  • State safety or emissions inspection prices, which are a different bill: see car inspection cost.
  • What technicians are paid, or the maker-only labor tables. The government wage pages, Ford's and GM's dealer manuals and the Tesla service pages were blocked or off the open web.

Your action plan: now, this week, before you pay

Now (ten minutes). Find your shop's last invoice. Does the labor line show hours and a rate? Write down what is missing.

This week. Before the next job, phone two shops and ask how each prices its work: flat rate or actual time, the hourly rate, and the guide. When you get an estimate, ask: please write on the estimate, for each job: the hours, the hourly rate, whether the hours are flat-rate hours or actual hours, and which labor guide the hours come from.

Before you pay. Compare the invoice with the signed estimate. Charges above the signed estimate usually need your approval first. If the hours look high, ask for the reason in writing, then read our guide on how to dispute a car repair bill. A quarrel over hours is never a reason to drive a car whose brakes or steering a shop has called unsafe: approve the safety repair, or get a second written quote the same day and have the car towed to that shop (our advice).

Sources and documents

Each page below was read on 13 November 2026. Marks: 🟢 official text; ⚪ a company's own statements. Where a page printed its own date, we give it.

  1. ⚪ Labor-guide publishers: Mitchell 1, labor times, Estimate Guide FAQs, Estimate Guide brochure, estimating and about us; ALLDATA, repair, blog, 3 February 2026, support: parts and labor, labor time adjustment and ALLDATA DIY; MOTOR, Estimated Work Times, 2016 product sheet, usage tips, 2025, 2014 flyer, 2015 flyer and 2015 catalog; Chilton, Cengage's 2013 labor guide page, a Gale flyer, 2023 and the Gale blog; Identifix Direct-Hit and its 2016 MOTOR and Chilton page; RepairPal's estimator page for shops (3 July 2024)
  2. ⚪ Vehicle makers: warranty documents of Toyota (2022 Prius), Honda 2024, Hyundai 2026, Nissan 2025, Subaru 2024, Mazda 2025, Cadillac 2026, Ram 2500 2021, Jeep Cherokee 2020, Kia 2020 and Mitsubishi 2021; GM TechLink, 29 April 2021
  3. ⚪ Trade body, AAA and shops: NADA, Managing Your Service Department for Profit (rev. 2014); AAA, labor-rate article 2026 and magazine column, 1 May 2021; shops, Kwik Kar, 27 May 2026, Andy's Automotive, 20 July 2022 and AGCO Automotive
  4. 🟢 Federal and state texts: FTC, Auto Repair Basics (page dated August 2012); California, Write It Right and the New Motor Vehicle Board document, protest PR-2803-22 (headed Proposed Decision Following Remand; the page returned an error when we tried to re-read it later the same day, so the quotes are from the saved extract); Florida 559.905, 559.909 and the attorney general's leaflet; Massachusetts 940 CMR 5.05, New York 15 NYCRR 82.5 and New Jersey 13:45A-26C.2 and 13:21-21.10 (read on Cornell's copy); Pennsylvania 37 Pa. Code 301.5; Maine section 1805, section 1802 and the attorney general; Connecticut chapter 246; Alaska 45.27.250; Illinois attorney general; Minnesota 325F.56 and 325F.58; Washington attorney general and RCW 46.71.025; Texas, Colorado, Arizona and Georgia attorney-general or consumer pages
  5. PulsCar homepage (sound check description)
  6. Not read, so not quoted: the Bureau of Labor Statistics and Department of Labor pages on technician pay, Ford's and GM's dealer labor-time manuals, Tesla's service pages, BBB, Consumer Reports, Edmunds, Kelley Blue Book, YourMechanic, RepairPal's methodology pages, the statutes of Michigan, Virginia, Oregon, Ohio, New Hampshire, Maryland and Wisconsin, and the Illinois statute (blocked, off the open web or not loading)

Prices verified: 13 November 2026 in the pages they are quoted from, each as printed on the page quoted · Technical documents verified: 13 November 2026 · Reviewed quarterly

Saw a rate, a rule or a labor-guide statement that differs from this page? Email [email protected] with the source and the date.