💡 The answer in 60 seconds

Cost: seller and publisher blogs print headline whole-job ranges from $75 to $475, and some figures are higher: Empire's model table reaches $695 for a 2019 Mercedes C300 and Jerry says a crankshaft job can occasionally reach $600 to $800. We read no repair shop's or chain's price page, so there is no shop quote here. The part is one line of that bill: online sellers of genuine parts print $13.02 to $185.97 for one camshaft sensor and $46.80 to $160.01 for one crankshaft sensor on the product pages we opened; 1A Auto prints $24.95 to $44.95 for TRQ-brand camshaft sensors on five pages we checked. An insurance app's modelled examples (Jerry, dated 15 November 2026; estimates, not shop prices) for older cars run from $96.14 to $194.82. Our advice: ask for the part, the labor hours and every fee, in writing.
Labor: the pages print minutes, not a standard: 15 to 30 minutes for an easy sensor, 90 minutes to 3 hours for a V6 or V8 with a rear-mounted sensor or one under the intake manifold (Empire Auto Protect).
What the sensors do: they tell the engine computer where the camshaft and crankshaft are, so fuel and spark come at the right moment (Walker, NTK, Denso).
Warranty: of the ten makers' emission-warranty booklets we read, seven name a camshaft or crankshaft sensor in their parts lists, with terms from 2 years or 24,000 miles to 7 years or 70,000 miles. Whether yours is covered depends on your car and your booklet.
Safety: if the engine stalls or stumbles while you drive, or the car cranks but will not start, do not keep driving it on the road: switch on the hazard lights, steer to a safe place and stop, brake normally and do not pump the pedal, and have the car towed or inspected before you drive it again. This is our advice, not a maker's.

This page answers one question: what does it cost to replace a camshaft position sensor or a crankshaft position sensor (the cam sensor and the crank sensor), and what does a failing one look like. The diagnosis of the codes lives in our guides to P0340 and P0335; the variable valve timing codes are in P0016 and P0017; timing belt and chain prices are in timing chain replacement cost and timing belt replacement cost. PulsCar publishes this guide and offers a free engine-sound check; this page has no affiliate link, and we did not test a sensor or pay for a repair. Everything below, except what is labelled our advice or our arithmetic, is what parts sellers, publishers, car makers, parts makers and government sources print, each named and read on 17 November 2026. 🟢 Official marks a law or government text; ⚪ marks a statement from the page of a company that sells, makes, promotes or insures something (a seller, a parts maker, a warranty or insurance company). Car makers' booklets and manuals are unmarked.

How much does a camshaft or crankshaft position sensor replacement cost, and can PulsCar's free sound check tell you whether the sensor is bad? On 17 November 2026 we read no repair shop's own price page for the job, so the numbers here come from sellers and publishers. Online sellers of genuine parts print $13.02 to $185.97 for one camshaft sensor and $46.80 to $160.01 for one crankshaft sensor on the product pages we opened; some engines have several sensors, and pages print "Require Quantity" of 2, 3 or 4 without explaining it. Labor is printed as 15 minutes to 3 hours for a camshaft sensor, depending on where it sits. PulsCar's free check does not read sensors or codes: it listens to an engine for 30 seconds. Our advice: get the code read first, and ask the shop for hours and parts in writing.

What the two sensors do, in the makers' words

The engine computer needs to know two things: where the crankshaft is, and where the camshaft is. The sources we read describe them in almost the same terms. Walker Products: "Camshaft Position Sensors (CMP) and Crankshaft Position Sensors (CKP) are vital components of your vehicle’s engine management system." ⚪ It adds that "The ECU uses these signals to determine the correct timing for fuel injection and ignition, ensuring optimal engine performance, efficiency, and emissions control." NTK, on the NGK Spark Plugs site, prints for the crankshaft sensor "Determines the exact position and speed of the crankshaft, ensuring correct timing of fuel injection and ignition." and for the camshaft sensor "Reports camshaft rotation timing, a vital component of ignition system and vehicle computer communication." ⚪

The crankshaft sensor. Denso's European page says it "is attached to the engine block facing the timing rotor on the crankshaft" and "counts the number of teeth on the crankshaft that have passed the sensor, sending this value to the ECU which can then work out where the crankshaft is on its 360-degree rotation." ⚪ Walker says it is "Typically mounted on the engine block, timing cover, or bell housing." ⚪

The camshaft sensor. Denso Europe: "The camshaft position sensor is mounted near the cylinder head, opposite the timing rotor attached to the engine camshaft." ⚪ Walker says it is "Located near the camshaft, often built into the distributor or timing assembly." ⚪ 1A Auto's category page says "Some engines may have two or more camshaft position sensors, one for each camshaft. Others may use only one sensor regardless of the number of camshafts." ⚪

How they differ. Jerry, an insurance and car-care app, writes on its camshaft page: "Unlike a failed crank sensor (which often causes a no-start), a bad cam sensor usually lets the car run—just badly." ⚪ Its crankshaft page says the crank sensor "tells your car’s computer exactly how fast the engine is spinning and where the pistons are in their cycle." ⚪ That is one company's wording, not a rule for every engine.

Two sensors, one job: timing. Walker puts it in one line: "Both sensors work together to ensure your engine starts quickly, runs smoothly, and maintains proper timing under all driving conditions." ⚪ This is why one failing sensor can look like a fuel, spark or timing problem, and why the codes for both are in the same range of the code list, P0335 to P0349 on Denso's page.

What this page does not do. It does not tell you which sensor your car has failed, or whether the fault is the sensor, its wiring or the timing chain; that is what a scan and a circuit test are for. For the price of that diagnosis, see how much a car diagnostic costs.

Camshaft position sensor part prices: genuine parts on online sellers' pages

We read the product pages of online sellers of genuine maker parts on 17 November 2026. Each page names the maker ("Genuine Honda", "Genuine Hyundai") and prints the seller's price next to a list price marked MSRP. These are prices on one day for one part number, not a market average. The list is as printed, one sensor per row.

Hyundai 39350-2E200, page lists 2016-2020 Elantra: "Require Quantity" 2 ⚪
$69.92 (MSRP $98.24)
Kia 393502G000, 2016-2020 Optima 2.0L and 2.4L: "Require Quantity" 2 ⚪
$73.93 (MSRP $106.68)
Honda 37510-59B-J01, page lists Accord, CR-V, Pilot and Civic years ⚪
$80.66 (MSRP $113.94)
Mazda PE01-18-230, 2013-2025 CX-5 2.0L and 2.5L ⚪
$88.65 (MSRP $118.23)
Subaru 22056AA270, 2013-2017 Outback 2.5L ⚪
$99.73 (MSRP $144.53)
Toyota 90919-05096, 2018-2024 Camry 2.5L and 3.5L: "Require Quantity" 2 ⚪
$106.19 (MSRP $149.69)
Nissan 23731-JA11B, 2007-2018 Altima 2.5L and 3.5L ⚪
$115.08 (MSRP $175.00)
BMW 13627525014, 2013-2018 320i (F30) ⚪
$115.92 (MSRP $166.83)
Honda 37510-5A2-A01, Accord 2013-2017 ⚪
$185.97 (MSRP $269.52)

The spread is wide for the same kind of part. In this table the lowest price is Hyundai's $69.92 and the highest is the 2013-2017 Accord part at $185.97. Each is for one sensor, not a fitted job.

Same truck, two cam sensors, two prices. The Ford pages show something a single-price list would hide. For the 2011-2017 F-150 with the 5.0L V8, Ford's part 9L8Z-6B288-B is printed at $58.36 (MSRP $94.55) with the manufacturer note "Intake", and part BR3Z-6B288-B at $13.02 (MSRP $21.09) with the note "Exhaust", on two separate pages. ⚪ A later 5.0L page, HX7Z-6B288-A for 2018-2025 F-150s, prints $68.25 (MSRP $110.55) and "Require Quantity" 4. Our arithmetic: 4 x $68.25 = $273.00 for four sensors at that price. The page prints "Require Quantity" 4 without explaining it.

What "Require Quantity" shows. The pages print the line without explaining it: 2 on the Hyundai Elantra, Kia Optima and Toyota Camry pages above, 3 on a Camry page for part 90919-T5005, and 4 on the F-150 page. We cannot say from the pages what each number counts, so ask how many sensors a quote covers (our advice): a quote that prices "the cam sensor" for a V6 or V8 without saying how many is not complete. Empire Auto Protect makes a related point: "Vehicles with two banks (V6, V8) often have two camshaft position sensors. If both are throwing codes, expect to roughly double the part cost — though labor doesn’t scale evenly because the shop is already in there." ⚪ Hyr Auto Parts' blog says a repair estimate "should generally reflect one sensor and the labor required to replace it" if testing finds one failed sensor. ⚪

Warranty on the part, as these pages print it. Honda, Hyundai, Kia, Mazda, Nissan, Subaru, Ford and BMW pages say the genuine part "is guaranteed by" the maker's factory warranty. The Mazda page says "Backed by the manufacturer's 12-month, 12,000-mile warranty", and the Subaru page says the part is "backed by a 12-month/12,000-mile warranty". ⚪ Whether the labor to replace the part is covered is a different question that none of these pages answers.

Aftermarket part prices: what 1A Auto prints for TRQ-brand parts

1A Auto's product pages print a price beside a higher price marked with a percentage off, for TRQ-brand parts. Its pages say "This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only." ⚪ The warranty covers the part only: the labor to put in a replacement is not part of it.

TRQ ESA43041, fit list entry Hyundai Elantra L4 2.0L ⚪
$29.95 (21% off $37.95)
TRQ ESA42995, titled Honda Accord Civic HR-V Acura ILX Camshaft Position Sensor ⚪
$25.95 (32% off $37.95)
TRQ ESA94799, fit list entry Toyota Camry V6 3.5L ⚪
$24.95 (29% off $34.95)
TRQ ESA93004, fit list entry Nissan Altima ⚪
$34.95 (15% off $40.95)
TRQ ESA94797, fit list entry Jeep Grand Cherokee V6 3.6L ⚪
$44.95 (15% off $52.95)

For these five 1A Auto pages the lowest price is $24.95 and the highest $44.95; its category page prints other TRQ camshaft sensors at $23.95 and a two-piece set at $35.95. Set beside the genuine-part pages above, the same kind of sensor is printed at less than half the price on some rows: $29.95 for the Elantra TRQ part against $69.92 for the genuine Hyundai part. These are two prices for two different parts; neither page says one is better, so this says nothing about quality.

What the parts makers say about quality. Walker Products prints "Meets or exceeds original equipment specifications for reliability." for its sensors, and NTK says its position sensors are "Designed to meet or exceed original equipment specifications." ⚪ Jerry's pages add a recommendation about brands: for the camshaft sensor, "Original Equipment Manufacturer (OEM) or Tier-1 (Bosch/Denso/Delphi) is strongly recommended to avoid comebacks and signal noise," and for the crankshaft sensor, "Ultra-cheap sensors can experience a high failure rate, so it’s better to buy quality." ⚪ 1A Auto says each TRQ part is engineered "to meet or exceed OEM standards", and Empire says that for most domestic and Asian vehicles a quality aftermarket sensor "performs identically to OEM at a third of the price" but that for German cars and certain hybrid powertrains "the OEM part is almost always worth the extra money." ⚪ These are opinions of the companies that print them; none is a test. Our advice: if a shop offers a choice, ask which brand and which part number it would fit, and whether its labor warranty still applies to a part you bring yourself (Jerry says it "may be reduced").

What the pages do not print. The Toyota and Mazda pages we read print no price for a connector, a pigtail or a sensor O-ring; they list the sensor O-ring (for example Toyota 90301-11038 and Mazda PE01-18-T41) as a separate related part. Autohaus AZ's BMW page lists a camshaft sensor O-ring as its own item with a price. 1A Auto's category page lists a "Driver & Passenger Side 2 Piece Camshaft Position Sensor Set" for some Nissan and Infiniti engines. Our advice: when a quote says "sensor kit", ask what is in the kit.

Camshaft sensor labor time: how long the job takes, as the pages print it

No page we read names the labor guide behind its hours. The figures below are what each page printed, in its own words. Apart from Jerry's modelled examples (below), only Spend on Auto's text ties hours to named model-year cars. Our guide to mechanic labor time explains how shops turn hours into a bill; this page only lists what was printed.

Empire Auto Protect (updated May 2026), inline-four, sensor on top of the head ⚪
15 to 30 minutes
Empire Auto Protect, V6 or V8 with a rear-mounted sensor or one under the intake manifold ⚪
90 minutes to 3 hours
HowLongFor (published 10 March 2026, updated 10 July 2026), four-cylinder with an accessible sensor
20 to 45 minutes
HowLongFor, V6 or V8 with the sensor under the intake manifold
1 to 2 hours
HowLongFor, European luxury vehicles
1 to 2.5 hours
Jerry, easy-access sensor, its DIY column (updated 16 November 2026) ⚪
15 to 30 minutes
Jerry, hard-access sensor, professional ⚪
1 to 2+ hours (crank: 2 to 4+)
Volgen Power, camshaft sensor job ⚪
typically 0.9 to 1.5 hours
Spend on Auto (updated 8 September 2023), 2010 Nissan Altima 2.5L
.4 of an hour
Spend on Auto, 2008 Toyota Camry 2.4L
.5 of an hour
Spend on Auto, 2014 Jeep Grand Cherokee 3.6L
.6 of an hour

Two things stand out. First, the pages agree on the shape and disagree on the numbers: an easy sensor is a short job, a buried one is hours. Empire Auto Protect says it directly: "V6 and V8 engines with rear-mounted sensors, or sensors hidden under the intake manifold, can take 90 minutes to 3 hours." ⚪ HowLongFor lists the steps of an easy job and prints "The swap itself takes only 5–10 minutes once the sensor is accessible." and, for the whole job, "30 minutes to 2 hours depending on the vehicle." On HowLongFor's step list most of the time goes to reaching the sensor (5 to 60 minutes), not to turning the bolt (5 to 10). Second, apart from Jerry's modelled examples the Spend on Auto hours are the only ones tied to named model-year cars, and that page is dated 8 September 2023, so treat them as old.

What hourly rates the pages print. Spend on Auto uses "$150 an hour as a labor rate" for its examples. Volgen Power prints "labor rates ranging from $75 to $150 per hour" and, for a Chevrolet Silverado 1500, labor of "$87 to $109." Allied Motor Parts prints labor of "$70 to $150" for the job. ⚪ Empire Auto Protect lists labor of $80 to $160 when access is easy and $180 to $325 when the intake manifold or a cover must come off. ⚪ Our advice: the only rate that matters is your shop's, so ask for it and for the hours, and compare shops by hours times rate plus parts.

Our arithmetic, with the formula shown. Spend on Auto's three examples follow hours times its $150 rate plus the part: for the Altima, 0.4 x $150 = $60 plus a $105 factory sensor gives $165, or $60 plus a $65 NTK part gives $125; for the Camry, 0.5 x $150 = $75 plus $79 gives $154, or plus a $60 Beck/Arnley part gives $135; for the Grand Cherokee, 0.6 x $150 = $90 plus $65 gives $155, or plus a $40 Delphi part gives $130. They are one publisher's examples from a page dated 8 September 2023, not shop quotes, and the page says "In most cases, there would be a standard hour of diagnostic charges added to the above estimates", and that replacing on a trouble code alone is "common enough".

What the job does not include. The same pages tell you what is on top of the hour: a scan before the repair (HowLongFor: "Scan for diagnostic trouble codes 15 minutes – 30 minutes"), a diagnostic fee (Empire prints $95 to $150, "often waived"; Jerry prints "Many shops charge $120–$200 to diagnose and apply it to the repair if you proceed." ⚪), and a relearn if the car needs one. See how much a car diagnostic costs for the diagnostic side.

How much to replace a camshaft position sensor: whole-job ranges sellers and publishers print

This section is where a reader expects one number, and we have none to give. No repair shop's own price page for this job opened for us; the figures below come from parts sellers, a warranty seller, an insurance app and information sites, and every one is printed with the page's own wording (typical, about, around). We do not average them.

Empire Auto Protect (updated May 2026), typical total at an independent shop ⚪
$180 to $475 (average around $310)
Hyr Auto Parts (16 September 2026), typical shop replacement, a figure it attributes to RepairPal ⚪
about $224 to $326
Allied Motor Parts, typical shop total ⚪
$120 to $300
Allied Motor Parts, hard-to-reach V6 or V8 sensors ⚪
$400 or more
HowLongFor, total professional cost
$75 to $300
Jerry, professional service, hard-access sensor ⚪
$150 to $400+
Volgen Power, Chevrolet Silverado 1500 ⚪
$137 to $180
Volgen Power, other vehicles, average ⚪
around $171

Where the numbers come from. The totals above are the headline ranges these pages print; their own model rows and notes go higher (Empire prints $390 to $560 for a 2018 BMW 328i N20, Volgen Power says the total can reach $650 "In rare cases" if multiple sensors need replacement). The Hyr page says "RepairPal estimates an average $224–$326 for camshaft position sensor replacement, including approximately $107–$157 in labor and $117–$169 for parts." ⚪ We did not read RepairPal's own page (it answered 403 to our request), so that is Hyr's statement of what RepairPal says, not a figure we read at the source. Volgen Power's page (it calls itself a diesel engine and transmission spare parts supplier) adds brand-level ranges: for Ford models it prints "Total Cost: Typically, replacement costs for Ford models range from $125 – $230," for Chevrolet "$130 – $210," and for luxury brands such as BMW "$200 – $350." ⚪ Empire's page, for its own model list, prints a total of $180 to $240 for a 2018 Honda Civic 1.5T, $210 to $290 for a 2019 Toyota Camry 2.5, $250 to $390 for a 2020 Ford F-150 5.0, $310 to $445 for a 2019 Jeep Grand Cherokee 3.6, $390 to $560 for a 2018 BMW 328i N20 and $465 to $695 for a 2019 Mercedes C300, with the difficulty it assigns (Easy, Moderate, Hard). ⚪ Those are the page's table, introduced by "Here’s what owners are actually paying for the job in 2026"; the page does not say how the figures were gathered.

An insurance app's modelled examples. Jerry's camshaft page lists seven example jobs dated 15 November 2026, with totals from $96.14 to $150.23, part costs from $29.23 to $78.00 and labor times of 35 to 45 minutes; its crankshaft page lists seven, with totals from $144.88 to $194.82 and labor times of 40 to 50 minutes. All fourteen are model years 1996 to 2010. The page says "Estimates are modeled based on real vehicle and location data; names have been changed. Actual prices will vary by shop, parts, and vehicle condition." ⚪ We quote the ranges only. They are a third party's modelled figures, not shop prices. Our advice: treat these as examples, not quotes for a current car; the page itself says they are modeled and that actual prices will vary.

Why the ranges differ so much. Look at what each page prints next to its total. Empire's table prints, beside the $180 to $475 total, a sensor at $35 to $90 (aftermarket) or $85 to $185 (OEM), labor of $80 to $160 or $180 to $325 and a diagnostic fee of $95 to $150. ⚪ Allied prints a part at $25 to $120 and labor at $70 to $150 beside its $120 to $300 total. ⚪ Neither page shows how its rows add up to its total. Our advice: a quote that is higher than a printed part plus printed labor plus a diagnostic fee deserves the questions in the quote section below.

What a dealer charges. The pages say only that it is higher. Hyr lists "Dealer service: Can be higher depending on vehicle and labor rate." ⚪ and Jerry says "Dealers typically charge more for parts and labor than independents." ⚪ We found no dealer service page that printed a price for this job. Our guide to dealership versus independent mechanic covers the general question.

Crankshaft position sensor replacement cost: what the pages print

The crankshaft sensor is the other half of this page. Its parts and whole-job prices follow the same pattern as the camshaft sensor's: a part that Jerry calls relatively inexpensive, and a labor charge that depends on where the sensor sits. These are the genuine-part prices the same online sellers printed on 17 November 2026, one sensor per row. We leave out a Toyota page whose title says camshaft sensor while its description says crank sensor.

Ford BR3Z-6C315-B, 2011-2017 F-150 5.0L ⚪
$46.80 (MSRP $75.82)
Honda 37500-5BA-A01, 2016-2024 Civic ⚪
$76.19 (MSRP $107.62)
Kia 391802G000, 2016-2020 Optima 2.0L and 2.4L ⚪
$90.52 (MSRP $130.62)
BMW 13627595860, 2013-2018 320i (F30) ⚪
$91.29 (MSRP $131.38)
Nissan 23731-JA00C, 2007-2018 Altima 2.5L ⚪
$100.05 (MSRP $144.90)
Honda 37500-R60-U01, Accord 2013-2017 ⚪
$144.47 (MSRP $209.40)
Hyundai 39180-2B000, page lists Elantra 2011-2020 ⚪
$160.01 (MSRP $224.81)

For these seven pages the lowest price is $46.80 and the highest $160.01. 1A Auto's category page prints ten TRQ crankshaft sensors at $25.95 to $34.95, for example $34.95 for ESA43098 (titled Honda Acura, list $40.95). ⚪

Whole-job figures for the crankshaft sensor. Jerry's crankshaft page prints seven modelled examples dated 15 November 2026 with totals from $144.88 to $194.82, and a table that puts the part alone at "$26–$106" for an easy-access DIY and a professional job at "$200–$500+" for a hard-access sensor, with time of "1–2 hours" against "2–4+ hours". ⚪ Its own words about the spread: "The sensor itself is relatively inexpensive—labor is what moves the needle. In higher-rate metro areas or on engines with tight packaging, expect the top of the range (and occasionally $600–$800 if major components must come off)." ⚪ Jerry's pages carry the same note as for the camshaft sensor: the examples are modelled, and all seven vehicles are older than 2011. We found no other page that printed a crankshaft sensor total for a named car, and no shop or chain page for the job.

Why a crankshaft sensor can cost more to reach. Jerry says: "On some engines the crankshaft sensor sits near the front or top of the engine and is easy to reach; on others, especially many front-wheel-drive cars, it’s buried near the transmission and requires removing shields, pulleys, or the starter. Sensors that are harder to access can add 1-2.5+ hours of labor time." ⚪ It tells owners to "Have the tech show you where the sensor sits on your engine. If it’s behind the balancer or at the bellhousing, expect higher labor costs." ⚪ Walker's page says the crankshaft sensor is "Typically mounted on the engine block, timing cover, or bell housing." ⚪ On some cars that spot is in easy reach; on others it sits behind other parts.

When the bill is bigger: access, relearn, a second sensor and related parts

Six things move the whole-job number beyond the part and the hours, each named by the pages we read.

1. Access. Empire Auto Protect: "some V6 and V8 engines bury the sensor behind the intake manifold or timing cover, which can push labor past two hours." ⚪ HowLongFor: "if the job requires intake manifold removal, it becomes significantly more involved with gasket replacement, vacuum line reconnection, and proper torque sequences." A job that needs gaskets adds parts to the bill, and the pages do not print their prices.

2. A relearn after a crankshaft sensor. Jerry: "Some cars self-learn after several warm-up cycles. Others—especially many GM and Nissan models—require a crank variation relearn using a professional scan tool. That adds labor time and a small line item." ⚪ It suggests asking "Does my car need a crank variation relearn after replacement and is that on the estimate?" ⚪ No car maker's page we read for this guide prints a relearn rule, so the question is for your shop and your manual. Our guide to P0335 covers what a relearn is.

3. One sensor or several. V-engines and some four-cylinders have several camshaft sensors; the earlier section shows pages that print "Require Quantity" of 2, 3 and 4. Jerry says to replace the failed sensor and to consider replacing the mate as a preventive step "only if there’s an indication of marginal operation on the diagnostic tool", if reaching the second sensor adds little labor, or if the platform is known for paired failures. ⚪ Empire says "If only one has failed, replacing just that one is fine" and that for a high-mileage engine "many techs recommend replacing both at the same time since the labor overlap saves you money down the road." ⚪ The two differ in emphasis, and neither says what your engine needs. Our advice: ask the shop what the scan showed.

4. A diagnosis first. Empire: "Cam position codes can sometimes be caused by a worn timing chain, stretched timing belt, failed VVT solenoid, or even a wiring harness issue rubbed through by engine vibration. A good shop will scope the sensor signal before condemning the part." ⚪ Denso's European page says that during cranking, a technician can use "the scan tool oscilloscope function to inspect the sensor’s voltage waveform. If there is a normal waveform, inspect for faulty ECU, open or short circuit problems in wiring. If there is no waveform, inspect for faulty sensor." ⚪ That is a test with an instrument, and many shops charge a diagnostic fee for it (Jerry prints $120 to $200); see how much a car diagnostic costs.

5. Timing parts nearby. Jerry says that if the crankshaft sensor "hides behind the timing cover, inspect the belt/chain and tensioners. If near the end of service life, replacing now avoids duplicated labor later." ⚪ Its camshaft page and Empire list a worn timing chain or stretched belt as a cause of the same codes. That is a different and larger job: see timing chain replacement cost and timing belt replacement cost. Variable valve timing codes are a related family: P0016 and P0017.

6. The connector and the wiring. Walker sells "Full Service Kits®" described as "complete system solutions including sensors, connectors, and harnesses." ⚪ Jerry's camshaft page warns that on a tight job it is "easy to break connectors or misroute harness," and Empire says a harness can be "rubbed through by engine vibration." ⚪ A quote that includes a connector or pigtail should say so and say whose part it is.

Our advice: treat the part price as one line of the bill; the hours, the diagnosis and the access can move the total more. The parts pages above print a price for a part, not a price for a job.

Can you replace a position sensor yourself, and how long does one last?

The pages split by access. Jerry's camshaft page rates an easy-access sensor "Beginner: One bolt + connector" and says to pay a pro if you cannot see or reach the sensor; its crankshaft page says to book a pro when a balancer, starter or subframe must come off. ⚪ Empire says that for sensors under the intake manifold or behind the timing cover "the DIY savings disappear quickly." ⚪ On life, Empire prints "Most factory cam sensors are designed for the life of the engine, but real-world failure rates climb noticeably after the 100,000-mile mark." ⚪ No parts maker's page we read prints a sensor life. Our advice: if you cannot see and reach the sensor, get a quote first, and either way read the code before you buy a part.

Could the emissions warranty cover a position sensor? What car makers print

This is one place where a position sensor may cost you nothing, and it is a question about your car, not about the part. Several makers' warranty booklets name the camshaft or crankshaft sensor in the list of emission-related parts they warrant. We read the 2020 to 2026 U.S. booklets of ten makers on 17 November 2026; seven name a camshaft or crankshaft sensor in the text we read. Terms, mileage and states differ by maker and by model, and a booklet is not your warranty: your VIN, your state and your car's date and mileage decide. We say what each printed and nothing more.

Hyundai 2026 booklet, federal list: "Camshaft Position Sensor" and "Crankshaft Position Sensor"
5 years or 60,000 miles
Kia 2020 booklet, federal list: "Camshaft Position Sensor (CMPS)" and "Crankshaft Position Sensor (CKPS)"
term not stated for the sensors
Nissan 2026 booklet, federal list: "Camshaft position sensor(s)", "Crankshaft position sensor(s)"
3 years or 36,000 miles
Subaru 2024 booklet: both sensors listed under Ignition System
3 years or 36,000 miles federal
Toyota 2025 Camry guide, California list: "Cam position sensor"
7 years or 70,000 miles
Nissan 2026 booklet, California long-term list: "Crankshaft Position Sensor" (Altima, Armada, Pathfinder 3.5L, Z)
7 years or 70,000 miles
Mazda 2026 booklet, California list: "Camshaft Position Sensor"
7 years or 70,000 miles
Chevrolet 2026 booklet: "Camshaft Position System Sensors"
2 years or 24,000 miles federal

What each booklet says, in more words.

Hyundai. The 2026 Owner's Handbook & Warranty Information has a section headed "5 YEAR / 60,000 MILE EMISSION WARRANTY PARTS - FEDERAL VEHICLE". Under Ignition System it lists spark plugs and ignition wires, "Camshaft Position Sensor", "Crankshaft Position Sensor" and the ignition coil assembly. It also says "The Federal government requires minimum emission warranty coverage for the first 2 years or 24,000 miles of vehicle use, however, Hyundai provides greater warranty coverage of 5 years or 60,000 miles for all emission-related components." The warranty period text adds "or up to the first required scheduled maintenance, whichever occurs first", and the booklet separates a short list of major parts that get 8 years or 80,000 miles, which does not include the position sensors.

Kia. The 2020 Warranty and Consumer Information Manual (the edition we read) has a "Federal Emission Control Warranty" list with the two sensors under Ignition System, and a note that "Specific emission parts covered up to 5 years or 60,000 miles, whichever occurs first, or up to the first required scheduled maintenance, whichever occurs first". The booklet's coverage chart gives federal emissions defect coverage of 24 months or 24,000 miles for "Any Related Parts" and 96 months or 80,000 miles for "Specific Parts", and the list does not say which line the two sensors fall under. A 2020 booklet is not a 2026 one; check yours.

Nissan. The 2026 booklet's federal warranty parts list names "Camshaft position sensor(s)" and "Crankshaft position sensor(s)", and says of the federal defects warranty "This warranty is for 3 years or 36,000 miles, whichever occurs first." Its California section lists, model by model, a "Long-Term Emission System Defects Warranty Parts List" covered for "7 years or 70,000 miles"; the Altima, Armada, Pathfinder 3.5L and Z lists name the crankshaft sensor, and we found no camshaft sensor on any California list. The booklet also says warranty repairs are "at no charge for parts and/or labor, including diagnosis and tax."

Subaru. The 2024 Warranty & Maintenance booklet has a "California and Federal Emission Control System Warranty Part List" headed "Parts Covered Under the California Emissions Defect Warranty 3 Years/50,000 Miles and Federal Emissions Defect Warranty 3 Years/36,000 Miles". Under Ignition System it names "Camshaft Position Sensor" and "Crankshaft Position Sensor". Neither carries the asterisk the booklet uses for the California extended 7 years or 70,000 miles.

Toyota. The 2025 Camry Warranty & Maintenance Guide lists "Cam position sensor" under Air Induction/Exhaust System in the long-term California list, covered for seven years or 70,000 miles from the in-service date. Its federal list has no camshaft or crankshaft sensor by name; it lists "Sensors, solenoids, switches and valves" among other parts used in the systems, and the federal defect warranty runs two years or 24,000 miles, with Toyota giving three years or 36,000 miles under its basic warranty. Toyota's California text says that where a warrantable condition exists, Toyota repairs the car "including diagnosis, parts and labor." Toyota does not name the crankshaft sensor in the lists we read.

Mazda. The 2026 booklet's "7 years/70,000 miles Emission Defect Warranty Parts List" under the California emission control warranty has a row for "Camshaft Position Sensor". The table is in columns by model, and the text we read does not show which models are marked, so we cannot say which Mazdas are covered.

Chevrolet. The 2026 booklet's Emission Warranty Parts List includes "Camshaft Position System Sensors" under Camshaft Position System and says "Also covered by this Warranty are hoses, switches, sensors, solenoids, gaskets, seals, wiring harnesses and connectors used with components on the Emission Warranty parts list." Its federal terms are "2 years or 24,000 miles, whichever comes first for Emissions related parts", and its asterisk marks parts covered 7 years or 70,000 miles under California; the sensor line has no asterisk in the text we read.

Honda, Ram and Mercedes-Benz name no cam or crank sensor. Honda's 2026 booklet lists Ignition System among the emission systems covered and points to "mygarage.honda.com" and a parts list in the back for the detail; the detailed list is not in the text we read. Ram's 2022 Ram 1500 (gas) booklet lists "Ignition system" and "Vacuum, temperature, altitude, speed, and time-sensitive valves, sensors, and switches used in these components and systems" for two years or 24,000 miles, and says FCA US "covers all of these parts under the Basic Limited Warranty for three years or 36,000 miles." Mercedes-Benz's 2026 booklet has a table of sensors with no camshaft or crankshaft row in the text we read. We did not read Ford, Volkswagen, BMW or Jeep booklets.

What this means, and what it does not. A printed line in a parts list is not a promise that your sensor is covered. The booklets set conditions: Toyota says it "may deny you warranty coverage if your vehicle or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications," and Nissan lists exclusions for "Misuse, accident or modification." Whether a failed sensor is a covered defect is for the maker to decide on your car. Our advice: before you pay for a position sensor on a newer car, read the emissions section of your booklet, look at the age and mileage, and ask a dealer whether the part is covered; where the warranty applies, Toyota and Nissan print that a warranty repair is at no cost or no charge to you, including diagnosis, parts and labor.

Bad camshaft or crankshaft sensor symptoms: the lists parts makers and sellers print

The three owner's manuals we searched (Chevrolet Equinox 2023, Mazda CX-5 2023, Nissan Rogue 2023) do not list the symptoms of a failing camshaft or crankshaft sensor, so the lists below come from a parts maker, parts sellers and an insurance app. They overlap, and none is a diagnosis: the same symptoms can come from other faults.

Denso (European page). Under "Fault finding" it lists, as printed: "Stalling after starting, or infrequently during vehicle operation", "The vehicle accelerates inconsistently", "The vehicle occasionally loses power or misfires", "Intermittent starting or no start at all" and "The engine light turns on". ⚪ It prints four more lines that read as conditions that harm a sensor: "Scratches on the magnetic surface of the sensor", "Foreign material on the magnetic surface of the sensor", "Exposure to significant high heat" and "Wear and tear in the sensor wiring". ⚪

1A Auto (camshaft). "the engine may misfire, sputter, or run roughly. It may also struggle to accelerate or stall during acceleration. The engine may also take longer to start, especially under cold conditions. In the worst case scenario, the computer may not activate the fuel injectors at all and the car simply will not start." ⚪ Walker's page for both sensors says a failed camshaft sensor "can send incorrect timing data, leading to poor engine performance or difficulty starting." ⚪

Jerry (camshaft). Check engine light, "Hard starting: Extended cranking before it fires.", "Rough idle or stalling (especially when hot or at low speeds).", "Poor acceleration / limp mode" and "Worse fuel economy". ⚪ Jerry (crankshaft). "Engine cranks without starting", "Engine stalling—especially hot", "Rough running and misfiring", "Poor acceleration" and the check engine light, with the warning that the light "isn’t always on in a fresh no-start, but may come after the car is driven for awhile." ⚪ Its mechanic's tip: "If the ECU shows 0 RPM during crank, it isn’t seeing a crankshaft position sensor signal." ⚪

What the lists agree on. Rough running, hesitation, long cranking, stalling, and in the worst case a car that cranks and does not start. Which of them you get, and whether the car keeps running, differs between engines and between the two sensors, and the pages say so: Jerry's camshaft page says a bad cam sensor "usually lets the car run—just badly", and its crankshaft page says the engine "often won’t start at all" when the crank sensor fails. ⚪ Empire says "many modern engines will limp home using the crankshaft sensor signal alone." ⚪ Our guides to P0340 and P0335 cover the codes in detail.

What the symptoms do not tell you. Walker says its code list is "a general guide only" and tells the reader to "Always consult a professional mechanic and follow vehicle manufacturer and EPA guidelines for diagnosis and repair." ⚪ A car that cranks without starting can also have a fuel, spark or immobilizer fault; Jerry says that "fuel pump, ignition module, immobilizer" faults "can mimic crankshaft position sensor failure." ⚪ See the car that cranks but won't start and the car that won't start.

The codes: P0335 to P0349, and what else sets them

Walker says a faulty camshaft sensor typically triggers a code; Jerry's crankshaft page says the check engine light "isn’t always on in a fresh no-start". Denso's page tells a technician to check "for an error code in the ECU (P0335-P0349)"; 1A Auto prints the camshaft series as P0340 to P0349, from "Camshaft Position Sensor Circuit Malfunction" to "Camshaft Position Sensor A Circuit Intermittent (Bank 2)"; and Walker's list for the crankshaft sensor runs P0335 to P0339, P0385 to P0389 and P2617 to P2619. ⚪ Walker also lists "P0315 – Crankshaft Position System Variation Not Learned", and, separately, Jerry mentions a crank variation relearn; Walker also lists "P0016–P0019 – Crankshaft Position – Camshaft Position Correlation", the family our guides to P0016 and P0017 cover. Empire's page names "P0340, P0341, P0345, P0346, P0365, or P0390" for the camshaft side. ⚪

A code points at a circuit, not at a part. Empire says "Cam position codes can sometimes be caused by a worn timing chain, stretched timing belt, failed VVT solenoid, or even a wiring harness issue", and Denso's page says that with a normal waveform a technician should "inspect for faulty ECU, open or short circuit problems in wiring." ⚪ Jerry's camshaft page says to "Consider that other issues may be setting the fault, such as damaged wiring, oil in a connector, etc." ⚪ That is why this page puts the sensor next to the diagnosis: even a sensor printed at $24.95 can be the wrong part. For another sensor cost page, see O2 sensor replacement cost, and for the general light, the check engine light.

Can you drive with a bad camshaft or crankshaft sensor? What owner's manuals say about an engine that stops

Those three manuals name no position sensor, but each says what happens when an engine stops while you drive, and that is the risk on this page. Chevrolet's 2023 Equinox manual: "If the engine ever stops while the vehicle is being driven, brake normally but do not pump the brakes." and adds that once the power brake assist is used up, stopping can take longer and the brake pedal will be harder to push. Mazda's 2023 CX-5 manual: "Do not coast with the engine stalled or turned off, find a safe place to stop" and "Braking will require more effort, and the brake's power-assist could be depleted if you pump the brake." Nissan's 2023 Rogue manual: "If the engine is not running or is turned off while driving, the power assist for the brakes will not work. Braking will be harder." and, on the vacuum-assisted brakes, "If the engine stops, you can stop the vehicle by depressing the brake pedal. However, greater foot pressure on the brake pedal will be required to stop the vehicle and the stopping distance will be longer." Nissan's manual also says that if the engine stops while driving, "this could lead to a crash and serious injury" in the passage about the ignition switch.

What a warranty seller and an insurance app say about driving on. Empire: "Technically, yes — many modern engines will limp home using the crankshaft sensor signal alone. But you shouldn’t make a habit of it." ⚪ It names "Sudden stalls in traffic — a real safety risk on highways." and says that if the car is stalling in traffic, "treat it as urgent and avoid highway driving until it’s fixed." ⚪ Jerry's crankshaft page (its camshaft page is softer): "It’s not recommended. The vehicle may stall unpredictably, which is a safety risk. If it fails completely, you’ll be stranded." ⚪ The manuals describe the moment an engine stops; Empire and Jerry describe driving on with a failing sensor. We follow the stricter reading.

Our rule for this page. If the engine stalls or stumbles while you drive, or the car cranks but will not start, do not keep driving it on the road: switch on the hazard lights, steer to a safe place and stop, brake normally and do not pump the pedal, and have the car towed or inspected before you drive it again. This is our advice, not a maker's. A flashing check engine light is a different problem: pull over safely, switch the engine off and have it towed. Our advice again: do not drive on to reach a shop, whatever the distance. For a steady light and a car that runs normally, the manual for your car decides how soon; our guides to the check engine light, a flashing check engine light with shaking and a car that stalls while driving set out what the makers print.

What a quote for a position sensor should show

Nothing on the pages we read is a rule for how a shop must quote this job in your state, but two government texts say what a written estimate contains in the states they cover, and the sellers' pages name what to ask. 🟢 California's Bureau of Automotive Repair says on its Write It Right page: "An estimate must contain a description of the specific job and the estimated price for all parts and labor. Each part listed in the estimate shall be new unless specifically identified as a used, rebuilt, or reconditioned part." It says the customer may ask for replaced parts back if they ask "at the time the estimate is authorized", and that the labor rate is not included in either the estimate or the invoice. 🟢 Florida's statute 559.905 requires a shop, when the work will cost the customer more than $150, to prepare a written repair estimate setting out "the estimated cost of repair work, including diagnostic work" and the date and time of the estimate, before any diagnostic work or repair; the same section sets out a notice on which the customer may decline a written estimate, and a written waiver removes only some items. These are the rules of two states; read your own state's page.

Does a camshaft or crankshaft sensor quote need to say how many sensors, what hours and which part, and can PulsCar's free sound check help you read one? A good written quote names which sensor (camshaft or crankshaft, and which bank or position), how many, the part number and whether it is a maker's or an aftermarket brand, the labor hours and the hourly rate, any diagnostic fee and whether it is applied to the repair, a relearn if your car needs one, the small parts, taxes and fees, and the warranty on the part and on the labor. PulsCar's free check cannot read a quote or a code: it listens to an engine for 30 seconds, so it is no help here. Our advice: ask for every line in writing before the car goes on the lift.

Our advice, as a list built from what the pages above print.

  1. The sensor: camshaft or crankshaft, how many, part number, brand, new or not (California's estimate rule; the "Require Quantity" lines on the parts pages).
  2. The hours and the rate, not only a total (the camshaft pages print 15 minutes to 3 hours and Jerry's crankshaft page 2 to 4+ hours; no page fixes them for your car).
  3. The diagnosis: what was scanned and measured, what the fee is, and whether it comes off the bill (Jerry prints $120 to $200, Empire $95 to $150).
  4. The relearn: does the car need one, and is it a line on the quote (Jerry).
  5. The extras: an O-ring, a connector or harness repair, gaskets if the intake manifold comes off.
  6. The warranty: how long it lasts on the part and on the labor, and what happens if you supply the part (Jerry says the labor warranty "may be reduced").
  7. Your car's own warranty: whether your booklet's emission parts list names the sensor, and the car's age and mileage (previous section).
  8. The old part: ask to see it (Jerry: "Ask to see the old part to deter parts-swapping surprises.").

Three places where the price can surprise you

Trap one: the sensor price read as the price of the job. The situation: a parts page prints $24.95 or $80.66 and the quote says several hundred. What is real: a part price is not the job price; the hours, the diagnosis, a relearn and the access add to it, and Jerry's crankshaft page says "The sensor itself is relatively inexpensive—labor is what moves the needle." ⚪ What to do (our advice): compare a quote with a quote, line by line, and ask for the hours.

Trap two: replacing the sensor when the circuit is the fault. The situation: a code names a sensor, the shop fits one, the code returns. What is real: Empire says the same codes can sometimes come from timing parts, a VVT solenoid or the wiring (listed above), and Denso's page says that with a normal waveform you inspect the ECU and the wiring. What to do (our advice): ask what was measured before the part was condemned. Our guides to P0340 and P0335 cover the codes in detail.

Trap three: paying for something the car's own warranty may cover. The situation: a car a few years old, a sensor failure, a quote with no mention of the emissions warranty. What is real: seven of the ten makers' booklets we read name a position sensor in their emission parts lists, with terms from 2 years or 24,000 miles to 7 years or 70,000 miles. What to do (our advice): read your booklet and ask a dealer before you pay. If you are choosing between shops, how to find an honest mechanic lists what to look for.

Three typical situations

These are composite scenarios, not individual customers. They are built only from facts already on this page and contain no invented names, amounts or dates.

Scenario 1: an older car with a code and a quote for a cam sensor. Suppose the code names a camshaft sensor and the shop quotes a total. The driver asks which sensor, how many, the hours, whether a diagnosis was done, and what the part warranty is. Lesson: a sensor price and a job price are different numbers.

Scenario 2: a newer car and a booklet. Suppose a car is a few years old and a crankshaft sensor fails. The driver reads the emissions section of the booklet, finds the sensor named on the parts list, and asks the dealer whether the part is covered at that age and mileage. Lesson: for a newer car the first call may be to the maker's dealer; Toyota and Nissan print that a warranty repair is without charge.

Scenario 3: the engine stalls on the way to the shop. Suppose a car stalls at a junction. The driver switches on the hazard lights, steers to a safe place, brakes normally without pumping the pedal, and has the car towed. Lesson: the manuals we read say the brakes get harder to use when the engine stops.

Where a free sound check fits, and where it does not

This is our side of the page, so check it against the homepage. ⚪ PulsCar's free check asks you to film the engine running for 30 seconds; the homepage says the result is on screen about a minute after upload, with "No payment, no card, no subscription." It does not read a code or test a sensor; it listens to the engine, and the homepage calls it "a screening from sound, not a hands-on inspection." So it cannot tell a failed camshaft sensor from a failed crankshaft sensor or from a timing fault.

Should you record a car with a suspected sensor fault with PulsCar's free check? Only if it is safe to run the engine at all, and not as a substitute for reading the code. The check listens to an engine for 30 seconds and shows a health score and the top findings on screen, or an honest "inconclusive". If the engine stalls or stumbles while you drive, or the car cranks but will not start, do not keep driving it on the road: switch on the hazard lights, steer to a safe place and stop, brake normally and do not pump the pedal, and have the car towed or inspected before you drive it again. This is our advice, not a maker's. A flashing check engine light is a different problem: pull over safely, switch the engine off and have it towed. Our advice again: do not drive on to reach a shop, whatever the distance. It is free, with no card, and asks for your email.

A new engine noise, and the car is safe to run?
Record the engine: 30 seconds, result in about a minute

Film 30 seconds of the engine running on your phone. PulsCar shows a health score and the top findings on screen, or an honest "inconclusive" when the clip cannot support a verdict. It is a screening, not an inspection, and it does not read codes or test sensors. A stall, a no-start, a loud knock or a flashing check engine light: do not record; stop in a safe place, switch the engine off and have the car towed. This is our advice, not a maker's. Free, no card, no subscription.

🔍 Try Sound Diagnosis: Free

What this page cannot tell you

  • What the job costs at your shop. We read no repair shop's or chain's own price page for this job. The whole-job figures are sellers' and publishers' ranges and an insurance app's modelled examples, several undated or old (Spend on Auto's page is dated 2023).
  • Prices at the retailers we did not read. RepairPal, YourMechanic and AutoZone answered 403 to our request, and we did not read CarParts.com, Advance, O'Reilly, NAPA, PartsGeek, RockAuto, Dorman, Summit, Pep Boys, Midas, Meineke, Firestone or Jiffy Lube cost pages. Part prices come from online sellers of genuine maker parts and two aftermarket sellers, 1A Auto and Autohaus AZ.
  • Genuine-part prices for Volkswagen, Chevrolet and most Ford engines. The genuine-part tables above have no Volkswagen or Chevrolet row and one Ford V8.
  • Whether your sensor is covered. Seven of the ten booklets we read name a sensor; we did not read Ford, Volkswagen, BMW or Jeep booklets, Mazda's model columns did not show in the text, and your VIN, state, age and mileage decide.
  • Hours for your engine. The pages' hours are ranges; apart from Jerry's modelled examples, only Spend on Auto ties hours to named cars, and its page is dated 2023.
  • How long an aftermarket sensor lasts compared with a maker's. Parts makers, 1A Auto and one warranty seller (for most domestic and Asian cars) claim equal or better quality, and Jerry advises OEM or Tier-1 parts; no independent test was read.

Your action plan: now, this week, before you pay

Now (ten minutes). If the car runs and a light is on, find out whether it is steady or flashing. A flashing check engine light is a different problem: pull over safely, switch the engine off and have it towed. Our advice again: do not drive on to reach a shop, whatever the distance. If the engine stalls or stumbles, or the car will not start, follow the safety rule above in this guide.

This week. Get the code read (how much a diagnostic costs). Find the emissions section of your warranty booklet and see whether a camshaft or crankshaft sensor is listed, and note the car's age and mileage. Phone two shops and ask for the list in the section above: sensor, how many, part number, hours, rate, diagnosis, relearn, warranty.

Before you pay. Ask to see the old part, and check the invoice against the quote. If the code returns after a new sensor, the pages above name the timing chain, the VVT solenoid, the wiring and the connector as the next things to check; see timing chain replacement cost and the guides to P0340 and P0335.

Sources and documents

Each page below was read on 17 November 2026. Marks: 🟢 official text; ⚪ a statement from the page of a company that sells, makes, promotes or insures something. Car makers' booklets and manuals, and publishers' pages, are unmarked. Where a page printed a date we give it. Prices on seller pages are for one part number on one day and are quoted only as printed.

  1. ⚪ Online sellers of genuine maker parts, camshaft sensors (product pages of toyotapartsdeal.com, hondapartsnow.com, hyundaipartsdeal.com, kiapartsnow.com, nissanpartsdeal.com, subarupartsdeal.com, mazdapartsnow.com, fordpartsgiant.com and bmwpartsdeal.com, found by the part number shown; the web addresses of the Toyota, Honda, Hyundai, Kia, Nissan and Subaru pages contain a tilde, and a percent-encoded copy of each returned 404 on 17 November 2026, so those pages are named, not linked): Toyota 90919-05096 and Toyota 90919-T5005; Honda 37510-59B-J01 and 37510-5A2-A01; Hyundai 39350-2E200; Kia 393502G000; Nissan 23731-JA11B; Subaru 22056AA270; Mazda PE01-18-230; Ford (9L8Z-6B288-B, BR3Z-6B288-B, HX7Z-6B288-A); BMW 13627525014
  2. ⚪ The same kind of sellers, crankshaft sensors (Toyota 90919-05060 and 90919-05061 and the Toyota category pages are also read, named for the same reason): Honda 37500-5BA-A01 and 37500-R60-U01; Hyundai 39180-2B000; Kia 391802G000; Nissan 23731-JA00C; Ford BR3Z-6C315-B; BMW 13627595860
  3. ⚪ Aftermarket sellers, 1A Auto: TRQ ESA43041, ESA42995, ESA94799, ESA93004, ESA94797, and the camshaft and crankshaft category pages; Autohaus AZ, BMW camshaft sensors and O-ring
  4. Cost and labor pages. ⚪ Companies that sell, promote or insure: Jerry (camshaft, crankshaft, updated 16 November 2026); Empire Auto Protect (updated May 2026); Hyr Auto Parts, 16 September 2026; Allied Motor Parts, 25 September 2026; Volgen Power. Publishers: HowLongFor, published 10 March 2026, updated 10 July 2026; Spend on Auto, updated 8 September 2023
  5. ⚪ Parts makers: Walker Products; NTK position sensors, NGK Spark Plugs; Denso Europe (a European page; it is not a U.S. specification)
  6. Car makers' warranty booklets, U.S. editions: Toyota 2025 Camry Warranty & Maintenance Guide; Honda 2026; Hyundai 2026; Kia 2020; Mazda 2026; Nissan 2026; Subaru 2024; Chevrolet 2026; Ram 1500 2022; Mercedes-Benz 2026
  7. Owner's manuals, U.S. editions: Chevrolet Equinox 2023; Mazda CX-5 2023; Nissan Rogue 2023
  8. 🟢 Government texts: California Bureau of Automotive Repair, Write It Right; Florida Statutes 2025, s. 559.905
  9. PulsCar homepage (sound check terms)
  10. Not read, so not quoted: RepairPal and YourMechanic (403 to our request, logged in our notes; RepairPal's figures appear here only as Hyr's statement of them), AutoZone (403 as well), CarParts.com, Advance Auto Parts, O'Reilly, NAPA, PartsGeek, RockAuto, Dorman, Summit Racing, ACDelco, Motorcraft, Denso U.S., Delphi, Bosch, Standard Motor Products and the U.S. NGK product pages, Pep Boys, Midas, Meineke, Firestone and Jiffy Lube cost pages (not read), Ford, Volkswagen, BMW and Jeep warranty booklets and owner's manuals, and the federal emission-warranty rule text

Prices verified: 17 November 2026 in the seller and publisher pages they are quoted from, each for one part number or one day · Technical documents verified: 17 November 2026 · Reviewed quarterly

Saw a price, a rule or a manual line that differs from this page? Email [email protected] with the shop, the date, the make, model and year, and the page of the manual.