💡 The answer in 60 seconds

Your car's manual decides first, and it is nearly silent on the material. We searched 29 owner's manuals from 14 car brands and none names ceramic, semi-metallic or any other material for pads; General Motors says to use approved parts, and Nissan and Infiniti say brake parts they do not recommend may stop the stability system from operating properly. Then the pad makers' own pages line up like this. Where they compare the types, ceramic is described as quieter and lower in dust and as gentler on rotors; semi-metallic is described as made for heat, heavy loads and severe duty. The makers disagree on heat, on life and even on what the words mean: a General Motors page calls its ceramic pads non-asbestos organic, and one Australian maker says its ceramic pads contain copper but no steel. Our advice: ask for the friction material the maker prints for the exact part number, or ask a dealer parts counter what pad the car came with. Brake pads are a safety part: if the brake pedal feels soft or sinks toward the floor, or the red brake warning light comes on or stays on while you are driving with the parking brake released, stop driving and have the car towed. We did not test any brake pad. PulsCar sells no brake pads and no brake brand pays us; there is no affiliate link on this page.

Which is better, ceramic or semi-metallic brake pads, and does PulsCar have a view? PulsCar has none, and says so before anything else: PulsCar sells no brake pads and no brake brand pays us; there is no affiliate link on this page. We did not test any brake pad, so nothing here says that one type stops shorter, lasts longer or is safer than the other. What the page does is line up three kinds of document: what your car maker's manual prints about brake pads, what pad makers print on their own pages about their ceramic, semi-metallic, low-metallic and hybrid lines, and what standards and state laws cover. Where the makers agree, as on ceramic being described as quieter and cleaner, the page says so. Where they disagree, as on heat and pad life, it shows both sides and leaves the decision to the manual for your car.

This is the comparison page. Our best brake pads guide already covers how AAA, a trade article and a tire maker compare the two types, the friction code, the copper leaf mark and a shortlist by use, so none of that is repeated here. This page uses different material: the makers' own product pages and technical articles, and the car makers' owner's manuals.

Every figure below names its source, and we read each page on 15 November 2026. 🟢 Official marks a government or standards text; ⚪ Maker's claim marks a pad maker's or car maker's own statement about its own product or vehicles, which is a claim, not proof. Most maker pages print no date, and we give a date where one is printed. Makers are listed alphabetically, never ranked. No maker page we read printed a brake pad price in dollars, so this page prints none; our brake pad replacement cost guide covers shop prices.

When your car's manual decides, and what 29 manuals say

What does my car's manual say about ceramic or semi-metallic pads? For almost every car, nothing. We searched the full text of 29 owner's manuals from 14 car brands (Cadillac, Chevrolet, Genesis, Hyundai, Infiniti, Jeep, Lexus, Mazda, Mercedes-Benz, MINI, Nissan, Subaru, Toyota and Volkswagen) for the words ceramic, semi-metallic, low-metallic, metallic pads, low-steel, non-asbestos, copper-free, NAO, organic pads and friction material, and read the brake chapters of Acura's and Kia's manuals as well. None of them names a pad material as required, recommended or better. The only hit is an equipment line in the Mercedes-Benz EQS manual that names a Mercedes-AMG ceramic high-performance composite brake system, which is a brake system, not a statement about pad choice.

What the manuals do print is narrower. Two families of car makers say that the replacement parts matter, and both tie it to a consequence.

Chevrolet Equinox 2026, Silverado 2025 and Cadillac Escalade 2025: "Always replace brake system parts with new, approved replacement parts. If this is not done, the brakes may not work properly. The braking performance can change in many ways if the wrong brake parts are installed or if parts are improperly installed." The Equinox EV 2026 and Cadillac LYRIQ 2025 manuals print the same text. ⚪
approved parts
Chevrolet Equinox 2026, Silverado 2025 and Cadillac Escalade 2025, pad life system: "This may be necessary if aftermarket brake pads without wear sensors are installed." The manuals describe turning the Brake Pad Life System off for that case. The Equinox manual adds "Brake pad life sensors must be replaced at the same time as the brake pads." ⚪
sensors
Infiniti QX60 2025: "If brake related parts such as brake pads, rotors and calipers are not INFINITI recommended or are extremely deteriorated, the ABLS system may not operate properly and the slip indicator light may illuminate." The manual prints the same condition for its VDC system. ⚪
stability system
Nissan Rogue 2026, LEAF 2026, Frontier 2024: "If brake related parts such as brake pads, rotors and calipers are not NISSAN recommended or are extremely deteriorated, the VDC system may not operate properly and the slip indicator light may illuminate." The Frontier manual also prints it with ABLS in place of VDC. ⚪
stability system

Read these for what they say and what they do not. General Motors says parts must be approved and that wrong parts can change braking performance; Nissan and Infiniti name their stability systems (VDC, vehicle dynamic control, and ABLS, active brake limited slip) and say the slip indicator light may come on. Neither says which pads are approved or recommended, and neither says a ceramic or a semi-metallic pad as such is wrong. They say the maker's choice is the reference point, and that the car's electronics can depend on it.

The remaining manuals (Genesis, Hyundai, Jeep, Lexus, Mazda, Mercedes-Benz, MINI, Subaru, Toyota and Volkswagen, and the Kia and Acura chapters) print no sentence about which pads to buy. Several send you to a dealer or workshop for pad replacement: Toyota and Lexus say "Have the brake pads checked and replaced by your Toyota dealer as soon as possible" (the Lexus manual says Lexus dealer), Subaru says "We recommend that you have your SUBARU dealer replace the brake pad," and the Volkswagen Tiguan manual says to go to "a correspondingly qualified workshop immediately" when the brakes are believed worn. ⚪ Three more makers print general advice, not specific to brakes: MINI's manual says the manufacturer "recommends the use of parts and accessory products approved by the manufacturer", and Mazda's says non-genuine parts or accessories "could affect your vehicle's performance or safety systems" and that the Mazda warranty does not cover this; Toyota's manual warns against non-genuine products too. ⚪ One misreading to avoid: the Toyota 2025 Corolla guide says "Warranty coverage is not dependent upon the use of any particular brand of replacement parts and you may elect to use parts that are not Toyota Genuine Parts for maintenance and repairs." That sentence sits in the federal emission-control warranty section and is about emission-control parts, not brakes. ⚪

The only car maker's pages we found that name pad types are the brake support pages of Cadillac, Chevrolet, GMC and Buick, which print the same Q&A about GM vehicles (undated). The answer to the question whether metallic pads shorten rotor life begins "Yes. Pads with higher metal content will tend to operate with more abrasive friction, where hard metal particles in the pad interact directly with the brake rotor surface." and continues "Use of metallic pads will create more brake dust and will shorten the rotor life. Most GM vehicles in North America use non-asbestos organic pads (also known as ceramic pads)." ⚪ That is one maker's statement about its own vehicles, and the Chevrolet, Cadillac and GMC pages close by sending you to the owner's manual for your vehicle. It is not a general verdict on semi-metallic pads, and it is a car maker's view of its own cars, not an independent one.

So the order is simple. Our advice: look in your own manual for the words approved, recommended or genuine near brake; if it has them, treat them as the limit. If it has none, which is the usual case, the manual has not ruled on the pad material, and the rest of this page tells you what pad makers print about each type.

The same words, different pads: what each maker means by ceramic and semi-metallic

Before comparing the two types, check that a maker's word means what you think it means. The sources do not use the words the same way, and the differences are printed on the makers' own pages. The grid shows what each one says it puts in the pad, alphabetically by maker.

ATE, ceramic: "In contrast to conventional brake pads, ATE Ceramic brake pads contain mild abrasives and no steel components." ⚪
no steel
Bendix (Australian site), ceramic: "synthetic glass fibres, aramid fibres, and natural fibres as the main reinforcing ingredients" plus organic modifiers "as well as metals such as copper, but no steel". ⚪
copper, no steel
Bendix (Australian site), semi-metallic and low-metallic: "Semi Metallic brake pads contain high amounts of steel and iron"; low-metallic pads "contain some ceramic materials but are designed for performance and high-speed driving styles." ⚪
steel and iron
General Motors support page: "Most GM vehicles in North America use non-asbestos organic pads (also known as ceramic pads)." ⚪
ceramic = NAO
Power Stop, semi-metallic and low-metallic: semi-metallic pads "contain anywhere from 30-65 percent metal"; low-metallic pads "are made of roughly 10-30 percent metal." Its own street lines are printed as ceramic or carbon-fiber ceramic. ⚪
30-65% / 10-30% metal
Raybestos, hybrid: "Element3 brake pads are engineered to combine the best of ceramic & semi-metallic formulations all into one brake pad." The same sentence is printed on an Element3 part whose specification line reads "Friction Material: Metallic". ⚪
hybrid or metallic
Wagner, semi-metallic SD: "Semi-metallic carbon-based friction material engineered in-house to deliver long lasting braking performance for the toughest applications"; Wagner's low-copper page says "Copper had long been a key ingredient of ceramic friction materials." ⚪
carbon-based

Four things follow from the grid. First, the ceramic pad is not defined the same way everywhere: ATE says its ceramic contains no steel, Bendix says its ceramic contains copper and no steel, and Wagner says copper was long a key ingredient of ceramic friction materials, so "ceramic" does not mean "no metal". Second, the semi-metallic bracket is a range, not a number: Power Stop prints 30 to 65 percent metal, and its own low-metallic bracket (10 to 30 percent) is a separate category. Third, General Motors uses the word ceramic for what it also calls non-asbestos organic pads, while Bendix files ceramic and non-asbestos organic in one group and calls low-metallic a different one; a car maker's use of the word and a pad maker's use of the word are not interchangeable. Fourth, makers add their own names (Akebono Ceramic Technology, Power Stop's carbon-fiber ceramic, Brembo's BRM X L01 compound, which Brembo says is made of over 30 different components); those are product vocabulary.

Raybestos does something no other maker does on the pages we read: its part pages print a "Friction Material" line (ceramic, semi-metallic, metallic or hybrid on the pages we read), usually next to an FMSI number (a fit number, not a material). If a maker prints no material, the type is unknown, not ceramic by default. For any pad you are quoted, our advice: ask which friction material the maker prints for that exact part number.

Who sells which: makers that print one type, both, or a hybrid

Your choice between the two types is first limited by what a maker sells. Reading each maker's own pages shows that several brands print only one side of the comparison.

Akebono: "Akebono manufactures ceramic brake pads in three distinct brands, each specifically formulated for domestic and Asian, European, or performance vehicles." No semi-metallic line named; its Severe Duty page prints "Vehicle-optimized ceramic formulas", and its pages call its pads an upgrade or replacement for semi-metallic pads. ⚪
ceramic, three brands
Bendix (Australian site): three compound groups, ceramic and non-asbestos organic, low-metallic and semi-metallic, in one bulletin that prints the date 05/09/22. ⚪
all three
Bosch: the Bosch brake pages we read name no pad material for QuietCast, Blue or Severe Duty. ⚪
material not printed
Brembo: Prime and Xtra each appear in a standard version and a ceramic version; the standard compounds are not described as semi-metallic on the pages we read. The Xtra ceramic page says the pads "are not meant for use on track." ⚪
standard and ceramic
Hawk: a Performance Ceramic compound and Ferro-Carbon street compounds (HPS, LTS, SD); the word semi-metallic appears on Hawk's pages only in a sentence about other brands. ⚪
ceramic and Ferro-Carbon
Power Stop: its street lines are printed as ceramic or carbon-fiber ceramic, and so is its Z37, listed for "Fleet, Pursuit Vehicles"; "carbon-fiber metallic" appears for its Track Day pad, and its fleet Z47 is printed as "Carbon-Fiber Semi-Metallic". ⚪
ceramic incl. pursuit; Z47 semi-metallic
Raybestos: "Application-matched ceramic or semi-metallic friction for everyday repair needs." Its Specialty Truck pad set is listed in a ceramic version and a semi-metallic version. ⚪
both, plus hybrid
Wagner: ThermoQuiet is titled "ThermoQuiet™ Reduced Noise Ceramic Brakes" and SD is the semi-metallic line; ES, QS and OEx do not name a material on their pages. ⚪
ceramic and semi-metallic

A maker whose pages print only ceramic, such as Akebono, describes a semi-metallic pad only as the thing you may be replacing. Wagner describes ceramic for everyday driving and semi-metallic for severe duty, and Bendix describes semi-metallic for heavy loads; Raybestos prints both for everyday repair and a ceramic Specialty Truck pad for "heavy duty performance". That is how the makers frame the choice, not a measurement. Other makers and retailers we tried (Centric, EBC, StopTech, Wearever, Carquest, NAPA and TMD Friction's own site) refused access or did not connect, so their lines are not covered here.

Does PulsCar recommend a pad type or a brand? PulsCar does not, because it sells no brake pads, tested none, and gets no payment from any maker. The grid above only shows what each maker chose to print about its own lines, and none of it ranks the makers: a maker that prints one type describes what it sells, and a maker that prints both says which of its lines it positions for which use. If you are choosing between two boxes, the maker's printed specification page for your exact vehicle, together with your manual, is the document to compare, and, our advice, the shop's invoice should name the line, the part number and the friction material, so that you can check all three against the maker's own page before you pay for anything.

Noise: what makers print, and what manuals call normal

Is a ceramic pad quieter than a semi-metallic one? The makers that compare them say yes.

ATE, ceramic against low-metallic: "ATE Ceramics are also less noisy and have a longer service life." ⚪
ceramic quieter
Ferodo, any pad: "Brake noise typically originates from vibration on a part within the wheel end section of the vehicle"; "Noise is often blamed on the brake pad itself, but can come from any part". ⚪
not only the pad
Hawk, other brands' semi-metallic: "Some brands of semi-metallic brakes are more likely to experience brake squeal due to the metallic ingredients in the brake pads." ⚪
some brands
Power Stop, semi-metallic and low-metallic: semi-metallic pads "can be noisier, especially when cold." Low-metallic pads "can be noisier than ceramic or NAO pads and tend to wear out faster"; in electric cars semi-metallic pads "are usually louder, which can be noticeable in an EV." ⚪
ceramic quieter
Textar epad+ ceramic: "Up to 30% quieter" than competitors, with no comparison method in the page text. ⚪
unnamed baseline
Wagner, semi-metallic and the system: semi-metallic pads "can be noisy"; "Vibration is the main source of noise in a brake system." Its ThermoQuiet ceramic pad "integrates the friction material, backing plate and insulator into a single high strength component." ⚪
pad and system

The makers agree on the direction, and the claims behind it are their own. They also say that noise is not only a property of the material: Wagner puts the cause in vibration and advises "Replace all anti-rattle clips, springs and pins which can lose their spring tempering due to the higher brake heat." ⚪ Ferodo says the pad is often blamed when another part is the source.

The car makers add what they call normal. The manuals separate noise they call expected, or not a fault, from the sound that means the pads are worn.

Chevrolet Equinox 2026: "Some driving conditions or climates can cause a brake squeal when the brakes are first applied, clearing up following several applications. This does not mean something is wrong with the brakes." ⚪
clears up: not a fault
Mazda MX-5 2023: "In high humidity weather conditions, brake noises, such as brake squeak or brake squeal can be heard. It does not indicate a malfunction." ⚪
humidity: not a fault
Nissan Rogue 2026: "Occasional brake noise during light to moderate stops is normal and does not affect the function or performance of the brake system." ⚪
occasional: normal

None of these sentences mentions a pad material, so no manual we read ties normal noise to ceramic or semi-metallic. And none of them calls the wear indicator's sound normal: Chevrolet says "The brake wear warning sound means that soon the brakes will not work well. That could lead to a crash. When the brake wear warning sound is heard, have the vehicle serviced." ⚪ The signs that a squeal has become the wear warning are in our when to replace brake pads guide, and what a grind means is in our grinding noise when braking guide. Our advice, not a maker's: whatever the material, a noise that persists or changes is a reason for an inspection, not for a change of pad type; for a soft pedal, see the stop rule in the wear-signals section.

Dust: makers, a car maker's support page and a manual

Which makes more dust? The pad makers that compare ceramic with metallic pads say metallic, and one car maker's page agrees. The wording differs from one maker to the next.

ATE: "ATE Ceramic pads create less brake dust than Low Met pads." ⚪
ceramic less
Brembo Greenance: "Designed to reduce particulate emissions by up to 80%"; the footnote says the values refer to the complete disc and pad system, the Greenance kit. ⚪
kit, not a pad type
General Motors support page: "Use of metallic pads will create more brake dust and will shorten the rotor life." ⚪
metallic more
Kia (2024 manual, disc brakes wear indicator): "Brake dust may accumulate on the wheels, even under normal driving conditions. Some dust is inevitable as the brakes wear and contribute to brake noise." ⚪
all pads make some
Power Stop: "Ceramic brake pads are known for producing the least amount of dust, compared to metallic or semi-metallic pads." Semi-metallic dust "is typically darker and more prone to sticking to wheels." Its Euro-Stop pads "produce an equivalent amount of brake dust to the OE product." ⚪
ceramic least; OE-match = OE dust
Textar epad+ ceramic: "Significant reduction in brake dust", with no baseline in the page text. ⚪
unnamed baseline
Wagner: semi-metallic pads "do create more dust than ceramic brake pads"; ceramic pads "produce very little dust or noise and are long lasting." ⚪
ceramic less

Where the makers compare the two types, the direction is the same. The caution is in two rows. Power Stop says its European-style pads, made to match the original, make as much dust as the original pad does, and Kia's manual says some dust is inevitable as the brakes wear; the other manuals that mention dust (Volkswagen's, Mercedes-Benz's and Jeep's) are about cleaning it. Volkswagen says "Remove brake dust with a suitable wheel rim cleaner or with Volkswagen Genuine wheel rim cleaner." and Mercedes-Benz says "Do not use acidic alloy wheel cleaners to remove brake dust. This could damage wheel bolts and brake components." ⚪ A dust or emissions claim (Brembo's 80 percent, Textar's "significant reduction") is only as useful as the baseline it names, and in these quotes the baseline is either the whole kit or unnamed.

Wear: pads, rotors and the claims nobody measured for you

Do ceramic pads wear rotors less, and do they last longer? On rotors the makers that speak to it lean one way. On pad life they print claims for both, each about its own line.

Akebono Pro-ACT (a leaflet with a 2019 copyright line): "Akebono Pro-ACT Brake Pads are gentler on your rotors over time." ⚪
ceramic, rotors
ATE ceramic: says its ceramic pads wear less than conventional low-metallic pads (pad wear), "especially when braking under everyday conditions", and that after a short running-in phase a transfer film develops on the disc. ⚪
ceramic, pad wear
Bendix (Australian site), ceramic: processing "dramatically increases the durability of the pads while also delivering low levels of dust, noise and rotor wear". ⚪
ceramic, durability
Bendix (Australian site), heavy-duty semi-metallic: "use more steel and iron to deliver high temperature performance and longevity", with "high integrity of the brake pad at temperature without lowering rotor life." ⚪
semi-metallic, longevity
General Motors support page: metallic pads "will shorten the rotor life"; non-asbestos organic pads "develop a transfer film, which is a layer of material on the pad and rotor surface that acts as a cushion (at a microscopic scale) between the pad and rotor." ⚪
metallic, rotors
Power Stop: "Brake pads that rely primarily on adherent friction can last longer because the pads do not grind down solely the rotor's surface. They also tend to have less brake dust." The same page says "There are no pads available that rely solely on either abrasive friction or adherent friction (although some may rely on one mechanism more than the other)." ⚪
friction mechanism
Wagner: semi-metallic pads are made of "friction materials that are harder than most others, so they may have more aggressive wear to your brake rotors." Its OEx line is "engineered to deliver up to two times longer pad life*, less dust, and reduced rotor wear", where the footnote reads "*Results based on internal testing comparing new Wagner OEx to other Wagner offerings." ⚪
semi-metallic, rotors; own-line test

Two points stand out. Wagner, General Motors and Power Stop describe one mechanism from different sides: harder or metallic material abrading the rotor, versus a transfer film cushioning it. Power Stop adds that no pad relies solely on either mechanism, so none of these sentences is a rule about any one pad. And the figures that look like measurements are not comparisons between types: Wagner's "up to two times longer pad life" compares its own OEx line with its other lines, on internal testing, and Bendix's durability sentence names no baseline. Hawk's blog of 09/03/2025 prints a general life figure for high-performance street pads and rotors and qualifies it: "High performance street brake pads and rotors may theoretically endure 25,000-30,000 miles and 50,000-75,000 miles, respectively. We say theoretically, because this life depends largely on your own personal driving style". ⚪ That is one maker's general range for performance street pads, with its condition attached; it is not an average for either type, and no page we read prints one.

Heat, towing and hard use: where the makers' own pages stop short

Is semi-metallic the right pad for towing? The makers do not answer with one voice. Several print semi-metallic for the hardest duty; others print ceramic for towing; and two print that one of their ceramic lines is not for racing. The grid shows what each prints, and what the same page sets as the limit.

ATE ceramic: "The ATE Ceramic is not suitable for high performance or racing!" The pad is designed for normal road traffic. ⚪
ceramic: not for racing
Bendix (Australian site), semi-metallic: "provide consistency of stopping power in high temperature conditions." ⚪
semi-metallic: heat
Brembo Xtra ceramic: studied "for a road sporty use", and "not meant for use on track." ⚪
ceramic: road sport
Hawk (2026 catalog): its SD line has "High fade resistance with superior high temperature and high inertia capabilities for heavy towing"; its LTS line lists "Strong and balanced initial bite, hot or cold" and "Ferro-Carbon friction". Of SD it also says "This product is not recommended for personal or recreational trucks and SUVs." ⚪
heavy towing, fleets; not personal trucks
Power Stop, towing page: "Ceramic brake pads are known for their durability and low dust production, making them a popular choice for towing." It adds "However, always be sure to stay within the manufacturer's recommended gross vehicle weight rating (GVWR)." ⚪
ceramic for towing
Power Stop, Jeep page: carbon-fiber ceramic pads "create less brake dust than many semi-metallic options" and "Their ability to withstand extreme heat helps prevent brake fade during demanding drives." ⚪
ceramic for off-road
Wagner SD, semi-metallic: "They are the ideal solution for frequent stopping, gear hauling and heavy payloads." ⚪
semi-metallic: heavy duty

Where the makers compare, they split. Power Stop positions its ceramic pads for towing and off-road, with a warning to stay within the manufacturer's gross vehicle weight rating. Wagner and Bendix position semi-metallic compounds for heavy payloads and commercial vehicles; for pursuit vehicles Raybestos prints a semi-metallic pad and Power Stop a ceramic one (Z37). ATE says its ceramic pads are not for racing, Brembo says the same of its Xtra ceramic pads, and Hawk sells Ferro-Carbon pads for towing and fleets, a compound it does not label semi-metallic on the pages we read. The extremes of use are where the makers disagree, and a general article cannot settle it for your truck.

The manuals say what to do when heat builds, and none ties the advice to a pad type. Hyundai's Elantra manual: "Applying the brakes continuously will cause the brakes to overheat and could result in a temporary loss of braking performance." ⚪ Acura's MDX guide says "Constantly using the brake pedal while going down a long hill builds up heat, which reduces the brake effectiveness." ⚪ Subaru's Outback manual says that with only the foot brake on a descent "the brakes may start working improperly because of brake fluid overheating, caused by overheated brake pads." ⚪ All three say to use a lower gear or engine braking instead. On the load side, Kia's manual lists "Using for towing or camping and driving with loading on the roof" and "Driving on uphill, downhill, or mountain road repeatedly" among its severe usage conditions, and says that if any applies "you should inspect, replace or refill more frequently, using the severe usage maintenance schedule instead of the normal usage maintenance schedule." ⚪ Jeep's Wrangler manual says that if a trailer weighs more than 1,000 lb loaded, it "should have its own brakes and they should be of adequate capacity", and that failing to do this "could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances." ⚪

If you tow, the first documents are your manual's towing section and its severe-duty maintenance line, which no pad type changes. If the brakes fade on a long descent, pull over safely and let them cool, then have the car checked (our advice), and if the brake pedal feels soft or sinks toward the floor, or the red brake warning light comes on or stays on while you are driving with the parking brake released, stop driving and have the car towed.

Life, warranty and price as printed

How long a pad lasts, what a maker's warranty covers and what the pad costs are what buyers ask, and the makers' pages give little on them. We read no pad price in dollars on any maker page, so this page prints none. Warranty terms, as printed, are below; a life statement for electric cars follows the table.

Akebono, warranty page: "Any product that does not comply with this limited warranty must be returned to the immediate seller/installer within thirty (30) days of purchase along with proof of purchase. Thereafter the warranty is void." ⚪
30 days to return
ATE, FAQ: asked whether its ceramic pads carry the same warranty as its normal pads, the page answers "Yes, there is no difference here between original ATE and ATE Ceramic." ⚪
same warranty
Hawk, 2026 catalog: "LIMITED LIFETIME WARRANTY"; the same page excludes "normal wear" and "improper installation or service." ⚪
lifetime, with exclusions
Power Stop, warranty page: for rotors and pads bought separately: "Power Stop LLC warrants its rotors and pads (excluding Track Day and Track Day Spec pads) to be free from defects in materials or workmanship for 90 days from the purchase date or 3,000 miles of use, whichever occurs first." The same page gives its performance kits "3 years from the purchase date or 36,000 miles of use" and its replacement kits "2 years from the purchase date or 24,000 miles of use." ⚪
separate pads 90 days; kits longer

Three cautions. First, Power Stop's warranty page gives different terms for the same brand depending on how the parts were bought: 90 days or 3,000 miles for pads bought separately, 2 or 3 years for kits, and 30 days for its Track Day pads. Its 60-day exchange for kits requires an invoice from a professional technician's installation and that the required break-in procedure was carried out. Second, none of these terms is comparable with another: a lifetime promise with exclusions (Hawk), a 30-day return window (Akebono) and a 90-day, 3,000-mile defect warranty (Power Stop pads) cover different risks, and none promises a pad life in a driver's hands. Third, the car makers treat pads as a wear item. Toyota's 2025 Corolla guide lists "Replacement of worn wiper blades, brake pads/linings and clutch linings" among normal maintenance not covered by its new-vehicle warranty, and Kia's 2020 warranty manual lists "Replacement or repair of parts intended to wear including the friction wear parts of the brakes, including brake pads and shoes" as not covered. ⚪ Kia's manual also excludes "Damaged brake rotors and drums resulting from failing to replace brake pads and/or shoes before they have worn sufficiently to damage such rotors and drums." ⚪ Not every maker draws the line in the same place: Rivian's 2024 R1T and R1S guide lists "brake pad/lining replacements;" among items covered in the first year or 12,000 miles when an adjustment is required by a defect in material or workmanship, and a 2015 Volkswagen booklet lists pads worn below manufacturer specifications as covered up to one year or 12,000 miles. ⚪ Those are warranty terms for particular vehicles and years; they say nothing about the pad type.

A life statement for electric cars comes from a pad maker: Wagner's article on servicing electric-vehicle brakes says "Since the conventional brake pads aren't used as much, they typically last longer than the pads on a conventional vehicle with an internal combustion engine (ICE)." ⚪ The section on electric and hybrid cars below says what the car makers add. Which type costs more: our best brake pads guide reports the price order that AAA and a tire maker print (ceramic costs more), and its cold-weather row covers first bite. For what a brake job costs at a shop, read our brake pad replacement cost guide.

What standards can and cannot compare

Is there a standard that says whether ceramic or semi-metallic is better? We found none; the SAE abstract disclaims it, and the others we read are silent on pad type. Four documents come up when pads are discussed, and each does a narrower job than the label suggests.

49 CFR 571.135 (the federal brake standard): applies to "passenger cars manufactured on or after September 1, 2000" and to light trucks, buses and multi-purpose vehicles up to 7,716 pounds made on or after September 1, 2002. Its wear-status rule says the wear of all service brakes must be shown by "Acoustic or optical devices warning the driver at his or her driving position when lining replacement is necessary" or by "A means of visually checking the degree of brake lining wear" from outside or underneath the vehicle. The text we read does not name ceramic or semi-metallic pads. 🟢
tests the vehicle
SAE J866 (friction code): the abstract says it "does not establish friction requirements for brake linings" and that "the friction codes obtained from this document cannot reliably be used to predict brake system performance." 🟢
a label, not a rating
FMSI numbers: FMSI says it created "a standardized part numbering system for brakes and clutch facings", so that "From manufacturer through retailer / installer one part number is used as the standard and as a common language." The page we read describes a numbering system, not a friction material or a performance rating. 🟢
fit, not material
ECE R90 (as Power Stop and Textar describe it): Power Stop says its Euro-Stop pads are "ECE-R90 certified" and that this "assures that brake components match OE tolerances and performance within 15%." Textar says its pads "exceed ECE R90 requirements and meet strict OE specifications". We did not read the regulation. ⚪
OE match, maker's word

What this adds up to: no standard we read ranks ceramic against semi-metallic. The federal standard governs the vehicle, as built; the SAE code is a label for a material's friction level; FMSI is a fitting system; Wagner says its OEx pad was validated on a dynamometer to SAE J2521 (noise) and J2522 (effectiveness), which we read only through the maker. None says which type suits your driving.

Copper: state laws, both pad types

Does copper law favour ceramic or semi-metallic pads? It does neither, and the makers' own pages show why. Washington and California limit copper in brake pads sold there, whatever the pad is called. Washington's Better Brakes law, as the state's Department of Ecology summarizes it, says brake pads and shoes manufactured after 1 January 2015 must contain 0.1 percent or less by weight of asbestos, hexavalent chromium, mercury, cadmium and lead; after 1 January 2021, "less than 5% copper by weight"; after 1 January 2025, "less than 0.5% copper by weight." 🟢 California's Bureau of Automotive Repair says SB 346 "prohibits the sale of motor vehicle brake friction materials containing more than 5% copper by weight" from 1 January 2021, as the second of three milestones toward less than 0.5 percent by 2025. 🟢 Washington's page also says a 2015 agreement between manufacturers, the federal Environmental Protection Agency and the Environmental Council of the States "means that every new brake pad sold in the United States will meet the standards of the Better Brakes Law"; a Washington House bill report (2017) calls that understanding voluntary and not intended to be legally binding. 🟢 We read no federal copper rule. Our best brake pads guide explains the LeafMark, the copper-level leaf symbol on the box.

The makers' pages show that copper does not line up with the type. Power Stop says semi-metallic pads are "composed of metals like copper, iron, steel, and graphite." ⚪ Bendix says its ceramic pads include "metals such as copper, but no steel", and Wagner says copper was long a key ingredient of ceramic materials. ⚪ On the other side, Wagner's undated low-copper page says "Wagner QS, Wagner SD and all brake shoes contain zero copper, which is not required until 2015. Wagner OEX and Wagner TQ use low-copper friction formulations that are not required until 2021." ⚪ SD is the semi-metallic line and TQ is the ceramic one, so on that page the semi-metallic pad is the zero-copper one and the ceramic pad is described as low-copper. Wagner's own pages differ, though: the SD and TQ product pages both print a zero-copper formulation, so check the page for the exact line. Brembo calls its Prime ceramic pads "copper-free", and Textar says its epad+ ceramic pads are "100% free of copper and antimony". ⚪ The practical reading: copper content is a labelled property of a particular line, not of ceramic or semi-metallic as a type.

Changing from one type to the other: what is printed

Can I fit ceramic pads on a car that came with semi-metallic ones, or the reverse? No page we read forbids it outright, and several say it needs care. What the sources print is below. Where a source speaks for a maker, the maker is named.

Akebono: its ceramic technology "can restore the original equipment ceramic brakes on your vehicle or be used as an upgrade for vehicles originally equipped with semi-metallic brake pads by delivering low-dust braking performance." ⚪
maker calls it an upgrade
ATE: "Use on just one axle is possible. To get the best result in terms of low brake dust production, however, ATE recommends that ATE Ceramic is used on both axles together with new brake discs." Also: "We do not recommend using Ceramic brake pads with sports brake discs." ⚪
both axles; not sports discs
Chevrolet and Cadillac manuals: "Always replace brake system parts with new, approved replacement parts. If this is not done, the brakes may not work properly." ⚪
approved parts
Nissan and Infiniti manuals: brake-related parts such as pads, rotors and calipers that are "not NISSAN recommended" (Infiniti: "not INFINITI recommended") may keep the VDC or ABLS system from operating properly. ⚪
stability system
Power Stop: "When replacing OE components with something comparable, you can generally switch from one brand to another without much consequence", and the same page says that although mixing brands is possible, "using the same brand offers certain advantages." This is about brands, not about pad material. ⚪
brand, not type

Read the grid as a map of who has said what. Akebono says its ceramic pads can be an upgrade for semi-metallic ones; ATE says its Ceramic pads are easy to install in place of standard pads, with two recommendations. The car makers that speak to parts (General Motors: approved; Nissan and Infiniti: recommended by the maker) tie it to the brakes working properly and, for Nissan and Infiniti, to the stability system. No page we read gives a test result for switching type, and no manual names a pad material, so none speaks to mixing materials between axles. Our advice, not a maker's: if you want to change type, make it a decision for the whole axle, ask the shop for the line, the part number and the friction material it prints, check the manual for the words approved, recommended or genuine, and on a Nissan or Infiniti ask the dealer what pad it recommends for the stability system. And never change pad type to cure a soft pedal: if the brake pedal feels soft or sinks toward the floor, or the red brake warning light comes on or stays on while you are driving with the parking brake released, stop driving and have the car towed.

Axle sets, rotors and bedding: the same rule for both types

The makers do not split by pad type on the next three points, which is itself a finding. Replace by the axle: Chevrolet's Equinox manual says "Brake pads should be replaced as complete axle sets." ⚪ Hyundai's Elantra, Elantra Hybrid and Santa Fe manuals and Genesis's GV70 manual say "Always replace brake pads as complete front or rear axle sets." ⚪ Kia's manual says "Always replace the front or rear brake pads as pairs." ⚪ Akebono's warranty page says "Install Akebono Disc Brake Pads only as a complete axle set". ⚪ Power Stop says "It's not advisable to replace the brake pads on only one side" and Hawk says pad and rotor replacement "should include both units, at the front and rear axle as a whole set". ⚪ A ceramic pad and a semi-metallic pad are fitted on the same terms: both pads on an axle, together.

Rotors come with pads. ATE says "As a general rule we recommend replacing the brake discs and the brake pads at the same time." ⚪ Power Stop says "Most professional mechanics recommend that vehicle owners replace brake pads and rotors at the same time." ⚪ Hawk's blog of 10/02/2026 says to check rotor thickness "to confirm they are within spec and not below discard depth" and the surface for deep grooves or scoring. ⚪ Wagner's complete-brake-job article says to change the hardware with the pads. ⚪ Whether your rotors are fit is a measurement, and our brake rotor replacement cost guide covers how to ask for it.

Bedding is where the maker pages first name the types. Wagner's break-in page says an effective burnish cycle "requires approximately 200 stops", asks for at least 30 seconds between applications and says "It is critical to follow cool down procedures to avoid damaging NAO, Ceramic and Semi-Met friction material as well as the rotor/drum." ⚪ Hawk says the street routine, in a post dated 10/02/2026, covers its Performance Ceramic, HPS, LTS and SD compounds in one procedure, and that without a transfer film "the brake system is working against itself." ⚪ Chevrolet, Cadillac, Volkswagen, MINI, Mercedes-Benz and Subaru print break-in notes for new pads. The table of those rules and the steps of the job are in our how to change brake pads guide. The point for this comparison is narrow: the sources that print a bedding routine do not print a different one for ceramic and for semi-metallic.

Hybrids and electric cars

Does the pad type matter differently on a hybrid or an electric car? No car maker we read says so. Among pad makers, Power Stop is the one that names a type as a fit for electric cars, in its own words; the other sources are about use, not material.

Brembo EV pads: "Developed for electric and plug-in hybrid vehicles, these pads prevent rust and eliminate noise." The page's composition is not named. ⚪
claim, no material
Power Stop, electric cars: semi-metallic pads "are usually louder, which can be noticeable in an EV"; "Ceramic Brake Pads: These are a great fit for most EV drivers." ⚪
ceramic named a great fit

Wagner and Brembo both describe a rust problem on lightly used brakes: Wagner says the pads "aren't used as much" on electric cars, so "brake pad rust doesn't have a chance to get scraped off", and Brembo says regenerative braking stresses the system less and that this "causes rust to form on the disc surface." ⚪ Toyota's Camry Hybrid manual and the MINI and Volkswagen manuals print wet-pad or low-mileage corrosion warnings. ⚪ No car maker says ceramic or semi-metallic matters more or less on an electric car; the Power Stop page does, and it is one pad maker's description of its own lines. Pad choice for these cars is a question for your manual and the shop. Our best brake pads guide lists the pad lines the makers position for electric cars.

When the pad is not the question: wear signals and the stop rule

A change of pad type cannot fix a worn pad, a leak or a soft pedal, and no warning below depends on the material.

Chevrolet Equinox 2026: "The brake wear warning sound means that soon the brakes will not work well. That could lead to a crash." ⚪
service the vehicle
Hawk (blog, 09/03/2025): "worn out brake pads should not be relied on to save you in high pressure braking situations." It adds that they can "crack or even shatter the friction material." ⚪
do not rely on worn pads
Kia 2024 manual: "Do not ignore high pitched wear sounds from your brakes. If you ignore this audible warning, you will eventually lose braking performance, which could lead to a serious accident." ⚪
do not ignore
Mazda MX-5 2023: "Do not drive with worn disc pads: Driving with worn disc pads is dangerous. The brakes could fail and cause a serious accident." ⚪
do not drive

Whatever the pad is made of, if the brake pedal feels soft or sinks toward the floor, or the red brake warning light comes on or stays on while you are driving with the parking brake released, stop driving and have the car towed. Two manuals are stricter on the light alone. Chevrolet's Equinox manual: if the brake system warning light is still on after the vehicle is pulled off the road and carefully stopped, "have the vehicle towed for service." Mazda's MX-5 manual, for a light that stays on with the parking brake released: "Do not drive with the brake system warning light illuminated." ⚪ A grind, a pull to one side or a pedal that pulses is an inspection, not a shopping trip: see our grinding noise when braking guide, car shakes when braking guide and brake light on dashboard guide. The thickness numbers and inspection intervals are in our when to replace brake pads guide, and they apply to both types.

The traps: three ways a pad-type decision goes wrong

Trap one: treating "ceramic" or "semi-metallic" as one fixed thing. The situation: a quote says ceramic, another says semi-metallic, and the choice looks like a choice between two materials. What is real: ATE says its ceramic contains no steel; Bendix says its ceramic contains copper and no steel; General Motors' support page calls ceramic pads non-asbestos organic ones; Raybestos prints a hybrid sentence on a part whose specification line says metallic. The price: paying for, or avoiding, a name instead of a pad. The defense: ask for the maker's line, the part number and the friction material the maker prints for that part.

Trap two: changing the type to fix something the type does not cause. The situation: the car squeals, shudders or feels different after a brake job, and a different pad type is offered as the cure. What is real: Wagner says vibration is the main source of brake noise; Ferodo says noise is often blamed on the pad but can come from any part; General Motors, Nissan and Infiniti tie the right parts to the brakes working properly and, for Nissan and Infiniti, to the stability system. The price: a second job within months. The defense: ask what was inspected (hardware, rotor, caliper movement), keep the measurements, and if the brake pedal feels soft or sinks toward the floor, or the red brake warning light comes on or stays on while you are driving with the parking brake released, stop driving and have the car towed.

Trap three: buying a comparison that has no baseline. The situation: a box says it is quieter, cleaner or longer-lasting by a figure. What is real: Textar's "Up to 30% quieter" is "than competitors", unnamed; Wagner's "up to two times longer pad life" compares its OEx line with its own other lines on internal testing; Brembo's "up to 80%" particulate figure refers to the whole disc and pad kit; Power Stop's low-dust formulation is "validated through on-vehicle 3rd party tests in the USA" without naming the third party. The price: a premium that rests on a sentence. The defense: a claim with a named test, a named baseline and a number is a fact you can compare; anything less is the maker's description of its own product.

Three typical situations

These are composite scenarios, not individual customers. They are built only from facts earlier on this page.

The commuter whose wheels turn grey. The wish is less dust. The makers that compare the types agree on the direction, and Kia's manual says some dust is inevitable as the brakes wear. The decision is not ceramic or not: it is what the manual says about approved parts, what the original pad was, which friction material the maker prints for the part being quoted, and whether both pads on the axle are being replaced.

The pickup owner who tows a trailer. Here the makers split: Wagner positions its semi-metallic SD line for heavy payloads, and Power Stop its ceramic truck pads for trucks that tow, with a reminder to stay within the vehicle's gross vehicle weight rating. The decision rests on the truck's manual, its towing section and its severe-usage inspection schedule, not on a general article. Our advice: if the brakes fade on a long descent, pull over safely and let them cool, then have the truck checked.

The Nissan owner quoted a "ceramic upgrade". The shop says the ceramic pad is quieter and cleaner, which is how the makers that compare the types describe it. The manual says brake-related parts such as pads, rotors and calipers that are not recommended by Nissan may keep the stability system from operating properly and may turn on the slip indicator light. The decision is to ask the dealer or shop what Nissan recommends for that car, to get the line, the part number and the friction material on the work order, and to have both pads on the axle changed together.

Where a free sound check fits, and where it does not

This is our side of the page, so check it against the homepage. PulsCar's homepage describes a free 30-second engine sound check, with no card, and a result on screen about a minute after upload; it also says the free check is a screening from sound, not a hands-on inspection.

Choosing between ceramic and semi-metallic pads is a decision for your manual, a parts counter and a shop, and a squeal, a grind, a pulsation through the pedal or a pull to one side after a brake job belongs with the shop that did the job.

Can a PulsCar sound check help me choose between ceramic and semi-metallic pads, or when something sounds wrong after I fit them? Not for the choice, and not for brake noise. The check listens to an engine, so it adds nothing to a pad decision and cannot judge pad wear, a seized caliper or a rotor. Its narrow use is an engine noise that was not there before, with the brakes and steering behaving normally. Brakes that feel wrong, steering or wheel noise, a flashing or red warning light: inspect first, do not record. A flashing check engine light is a different problem: pull over safely, switch the engine off and have it towed; the only exception, a flashing light alone on a car that starts and runs normally, is a shop within 2-3 miles, reached gently, under 40 mph with light throttle.

A new engine noise, and the brakes and steering feel normal?
Record the engine: 30 seconds, free

Film 30 seconds of the engine running on your phone. PulsCar's free check listens to the engine for early signs; it does not inspect brakes and cannot see a brake fault. Brakes that feel wrong, steering or wheel noise, a flashing or red warning light: inspect first, do not record. Free, no card.

🔍 Film my engine, free

What this page cannot tell you

We tested no pad, so nothing here says that a ceramic pad stops shorter, lasts longer or wears rotors less than a semi-metallic one, or the reverse; every comparison above is a maker's description of its own product, a car maker's statement about its own vehicles, or a standard's scope. We read no pad price in dollars on any maker page, so the page cannot say what either type costs. We read 29 owner's manuals from 14 car brands, for particular models and years; the Volkswagen Tiguan manual is an India edition (print status 23.07.2021), and the Lexus and two Toyota manuals are copies from Canadian sites. Your car, model year and market may differ, and your own manual is the document that governs. Honda's manual pages refused every request (HTTP 503), and Ford's, Volvo's, Tesla's and BMW USA's own sites and Toyota's asset servers refused access or did not answer, so those makers' statements are missing apart from the Toyota and Lexus manuals listed; Ram, Chrysler, Dodge, Audi and Jaguar Land Rover manuals we did not look for, and for Porsche we read only a quick start guide with no brake-pad text. EBC, Centric, StopTech, Wearever, Carquest, NAPA and TMD Friction's site refused access or did not connect. We did not read NHTSA's brake pages (the site refused access), and the IIHS and EPA pages we tried at addresses we guessed did not exist there, so no federal safety-agency page on pad type is quoted. We read SAE J2521, J2522 and ECE R90 only as the makers describe them, and the copper laws only from Washington and California sources.

Your action plan: before you shop, at the shop, after the fit

Before you shop. Look in your own manual for the words approved, recommended or genuine near brake. In the manuals we read, those words appear in Nissan, Infiniti, Chevrolet and Cadillac manuals; for other cars, ask a dealer parts counter what the original pad was. Note your use (daily, towing, mountain roads) and what the manual says about severe usage. If the brakes already feel wrong, do not shop first: if the brake pedal feels soft or sinks toward the floor, or the red brake warning light comes on or stays on while you are driving with the parking brake released, stop driving and have the car towed.

At the shop. Ask for the line, the part number and the friction material the maker prints for that part; whether the pads replace the original type or change it; whether hardware and wear sensors are in the box (Chevrolet's Equinox manual says pad life sensors must be replaced with the pads); whether both pads on the axle are being replaced; the rotor thickness against the minimum printed on the rotor or in the manual (see our brake rotor replacement cost guide); the warranty terms in writing; and the maker's bedding instructions. For the price of the job, see our brake pad replacement cost guide; to fit the pads yourself, see our how to change brake pads guide.

After the fit. Follow the bedding rule in your manual or the pad maker's sheet, and do any hard stops only where it is safe and legal. A pull, a grind or a pedal that feels different is a reason to go back at once. If the brake pedal feels soft or sinks toward the floor, or the red brake warning light comes on or stays on while you are driving with the parking brake released, stop driving and have the car towed. Keep the receipt with the line and part number.

Sources and documents

Each page below was read on 15 November 2026. Marks: 🟢 government or standards text; ⚪ a pad maker's or car maker's own statement. Most maker pages are undated; where a date is printed we give it.

  1. 🟢 Federal brake standard, 49 CFR 571.135; SAE International, J866 recommended practice abstract; FMSI home page and About FMSI
  2. 🟢 Washington State Department of Ecology, Better Brakes law page; Chapter 70A.340 RCW; House final bill report on SHB 1738 (2017)
  3. 🟢 California Bureau of Automotive Repair, Understanding California's Brake Pad Law, Spring 2021; brake friction materials presentation; enrolled text of SB 346 (2010)
  4. ⚪ General Motors owner's manuals: Chevrolet Equinox 2026, Equinox EV 2026, Silverado 1500 2025, Cadillac Escalade 2025, Cadillac LYRIQ 2025; GM vehicle-support pages on brakes: Chevrolet, Cadillac, GMC, Buick (undated)
  5. ⚪ Nissan owner's manuals: Rogue 2026, LEAF 2026, LEAF 2023, Frontier 2024; Infiniti QX60 2025
  6. ⚪ Hyundai and Genesis owner's manuals: Elantra 2023, Elantra Hybrid 2023, Santa Fe 2023, IONIQ 5 2023, Genesis GV70 2023
  7. ⚪ Kia owner's manual pages: disc brakes wear indicator (2024), power brakes (2023), severe usage conditions (2023), 2020 warranty and consumer information manual
  8. ⚪ Toyota, Lexus, Subaru and Mazda: Toyota Camry Hybrid manual, Toyota RAV4 Hybrid manuals (OM0R193U and OM0R160U, toyota.ca copies), Lexus NX350h 2024 manual, Toyota 2025 Corolla warranty and maintenance guide, Subaru Outback 2024 manual and 2022 manual, Mazda CX-90 PHEV 2024 manual, Mazda MX-5 2023 manual
  9. ⚪ Acura, Jeep, Mercedes-Benz, MINI, Volkswagen and Rivian: Acura MDX 2023 brakes chapter, Jeep Wrangler 2026 manual and 2023 manual, Mercedes-Benz C-Class 2022 and EQS 2022 manuals, MINI Countryman 2025, Volkswagen Tiguan user manual (India edition), Volkswagen USA 2015 warranty and maintenance booklet, Rivian regenerative braking story and R1T and R1S warranty guide (2024)
  10. ⚪ Akebono: home, domestic, EURO, Severe Duty, Pro-ACT leaflet, warranty page; ATE: ceramic brake pads and its FAQ
  11. ⚪ Bosch, brakes; Bendix Brakes Australia, not all pads are the same (prints 05/09/22); Brembo: maintenance FAQ, Prime ceramic, Xtra, Xtra ceramic, Greenance, EV pads; Ferodo, brake noise; Textar: epad+ and brake pads
  12. ⚪ Hawk Performance: 2026 product catalog, FAQ, blog posts bedding brake pads (10/02/2026) and how do I know if it's time to replace my brakes (09/03/2025)
  13. ⚪ Power Stop: brake pads with less dust, brakes for electric vehicles, brake pad options, Z23 versus Euro-Stop, brakes for Jeeps, pads for towing, break-in procedure, replace pads and rotors together, same brand of pads and rotors, Euro-Stop, brake pad range, Z16, Z37, warranty
  14. ⚪ Raybestos: home, Element3 rear hybrid pad set, Element3 rear metallic pad set, Specialty Truck ceramic, Specialty Truck semi-metallic, Specialty Police
  15. ⚪ Wagner: best brake pads to buy, ES, QS, SD, OEx, ThermoQuiet, low-copper page, brake system noise, break-in, PPV testing, electric-vehicle brake service, complete brake job
  16. PulsCar homepage (sound check terms)
  17. What we could not read, and so did not quote: EBC Brakes, Centric, StopTech, Wearever, Carquest, NAPA and TMD Friction (refused access or did not connect); Honda, Ford, Volvo, BMW and Tesla manuals and Toyota's asset-server PDFs (refused access or did not answer); NHTSA's brake pages (refused access); IIHS, EPA and Car Care Council pages at the addresses we tried (did not exist there)

Prices verified: no brake pad prices are printed on this page; none were printed on the pages read, 15 November 2026 · Technical documents verified: 15 November 2026 · Reviewed quarterly

Saw a pad line, a manual statement or a figure that differs from this page? Email [email protected] with the line, the vehicle and the source.