The answer in 60 seconds

Hand the job to a shop if the car has an electric parking brake on the axle you are working on, if it is a hybrid or an electric car, if your car maker's manual or service information says a dealer or technician should replace the pads, or if you have no jack stands or no torque wrench. None of the 18 owner's manuals we read prints a pad-change procedure; Toyota, Subaru, Volkswagen and Mercedes-Benz send pad work on worn or suspect brakes, or service and repair in general, to a dealer or a qualified workshop, and Brembo says its product is intended to be installed only by a skilled, qualified professional. If none of that fits, the pad makers' order is:

  1. Loosen the wheel nuts about one turn while the wheel is on the ground, then lift the car on firm, level ground. Never get under a car, or work on a wheel, with the car held up by a jack alone. Lift it at the jack points in your owner's manual, set jack stands under it, chock the wheels that stay on the ground, and keep the engine off.
  2. Take the wheel off and look at the caliper, guides, hose, rotor and wheel bearing.
  3. Open the reservoir cap before you push the pistons back, watch the level, wipe up any spill at once, and do not top the reservoir off beforehand.
  4. Take one caliper off at a time and hang it from the chassis, not from the hose; push the piston back with the right tool; lubricate only where the maker says; fit the new pads the right way round. Replace the pads on both wheels of an axle together, never one side only.
  5. Refit the caliper to the torque your vehicle maker prescribes (not in the owner's manuals we read), then refit the wheel.
  6. Lower the car so its tires carry its weight, then tighten the wheel nuts or bolts with a torque wrench to the number in your owner's manual, in a criss-cross pattern; never use an impact wrench on them above its lowest setting, and never oil or grease the threads.
  7. Before the car moves, press the brake pedal several times until it is firm. If the pedal is soft, sinks, or stays low, or the red brake warning light stays on, do not drive the car: have it towed. New pads brake weaker until they are bedded in; leave extra distance.

We make PulsCar, which has a free engine sound check. This page sells nothing, has no affiliate links, and does not offer the sound check for brakes: a noise from a wheel, a soft pedal or a brake warning light needs a hands-on inspection first. Everything here is what other people print, read on 11 and 12 November 2026 and saved as text. We changed no brakes and tested no pad.

The question is narrow: you have decided the pads are due and want the steps, what the makers print about the dangerous parts, and when to stop. When pads are due is the subject of when to replace brake pads; which pads to buy is best brake pads; prices and the rotor question are in brake pads replacement cost and brake rotor replacement cost; fluid work is how to bleed brakes and how to check brake fluid.

We searched the full text of 18 owner's manuals from 11 makers (Chevrolet, Genesis, Hyundai, Infiniti, Mazda, Mercedes-Benz, MINI, Nissan, Subaru, Toyota and Volkswagen) for the pads, the parking brake, the brake fluid, the jack and the wheel nuts. For the steps we read the pad makers: Brembo's installation instructions, Wagner's technical tips, DBA's bedding bulletin, a Hella page and Power Stop's support page, plus a federal workplace rule on brake dust and an AAA page. We could not read the manuals of Tesla, Ford and Honda (refusal or service error) and did not get around them; we did not look for Jeep, Ram, BMW or Volvo. "The makers" here means the makers we could read.

Stop first: who should not change these pads at home

Hand the job to a shop if the car has an electric parking brake on the axle you are working on, if it is a hybrid or an electric car, if your car maker's manual or service information says a dealer or technician should replace the pads, or if you have no jack stands or no torque wrench. The last two conditions are plain: without stands the job cannot be done safely, and without a torque wrench the wheel nuts cannot be tightened as the makers print. The electric parking brake and the hybrid and electric clauses are this page's cautious rule, not a maker's blanket ban; the sections on those cars show what the papers say and where they are silent. Three of the five brake makers say their instructions are for professionals, and they are still the best steps we found.

Three of the five brake makers we read say it is for professionals, and the other two point you to one. Brembo's instructions open with this danger notice: "This Product is intended to be installed only by a skilled, qualified professional who has been trained and/or is experienced in the installation and use of this Product". DBA: "We recommend that brake parts should only be fitted by a qualified technician"; a Hella page says its information is for suitably qualified personnel. Wagner's tips say they should not be used in lieu of advice from a certified technician or mechanic, and Power Stop calls its installation guide reference only.

The car makers send the work to a dealer or a workshop when pads are worn or the brakes are suspect. Toyota's Camry Hybrid manual, on a squeal or scrape from the wear indicators: "Have the brake pads checked and replaced by your Toyota dealer as soon as possible." Subaru's Outback manual: "We recommend that you have your SUBARU dealer replace the brake pad." Volkswagen: "go to a correspondingly qualified workshop immediately and have the brake system checked and have any worn brake pads replaced. Volkswagen recommends using a Volkswagen dealership." Mercedes-Benz is broader: for "Safety-relevant works", "Service and maintenance work" and "Repair work" it says "always have your vehicle checked at an authorized Mercedes-Benz Center", and MINI says to have a worn-pad warning checked at an authorized or other qualified service center. None of these is a procedure, and none of the 18 manuals prints one. AAA: "Fixing your own brakes saves on labor fees, but complex setups mean you should rely on an Automotive Service Excellence (ASE) certified technician."

If any of these fits you, stop here and hand the job over.

  1. The car has an electric parking brake on the axle you are working on, or is a hybrid or an electric car (sections below).
  2. Your car maker's manual or service information says a dealer or technician should replace the pads (Toyota, Subaru and Volkswagen do).
  3. You cannot lift the car safely on jack stands, on firm, level ground, at the points your owner's manual shows, or you have no torque wrench.
  4. The pedal is already soft, the red brake warning light is on, or you can see fluid wet around a wheel. Do not drive the car to a shop that way: have it towed.

If none fits, the rest of the page is the conventional job.

What you need: the tools, parts and protection the makers name

No document we read prints a full shopping list for a pad job (Brembo's EV-kit page names a torque spanner, an expanding tool and pull-out hooks; Power Stop's guide opens with a tools step we could not read in full), so this list is assembled from what the pad makers and car makers say. It is the minimum their words imply, not a certified kit.

To hold the car up. A jack, and jack stands. Nissan's do-it-yourself section, in its engine-oil change steps, says: "Raise and support the vehicle using a suitable floor jack and safety jack stands." And wheel chocks, which one of Brembo's danger notices lists: "chock the wheels not being worked on, jack up the vehicle and ensure that the vehicle is in a stable position."

To take the wheel off and put it back. The wheel wrench and, for the end of the job, a torque wrench. Brembo's page on tightening torques says "Tightening of the wheels must be performed with the use of a torque wrench" and allows a pulse wrench only on its lowest setting, and only if the tool's torque cannot exceed the required torque, or a wrench with a torque-limiting function.

To push the piston back. The right tool for your caliper. Brembo: "Ensure that the pistons and seals are not damaged during retraction by using the correct tool to retract." The papers we read name no tool beyond "the correct tool"; which one fits yours is a question for the caliper's maker or the service manual.

To clean and lubricate. DBA's bulletin names "a suitable brake cleaner product and clean cloth or paper towel" for oil or metal filings on an uncoated rotor; Brembo adds "Do not use products that could damage the rubber parts such as nitro thinner, petroleum etc." The lubricants section below sets Brembo and Wagner side by side.

New hardware. Brembo says to replace worn or damaged shims, the pad springs with every pad replacement, and corroded guide bolts. Power Stop's support page says it supplies new hardware with its kits, with two named exceptions.

To protect yourself. Brembo: "Always use a respirator or other suitable equipment to prevent the inhalation of dust raised during cleaning of the parts and components."

Holding the car up: what the car makers print about the jack

Most of the jack warnings in the manuals are written for the jack in the trunk and a flat tire; Nissan, Infiniti and Subaru also print the safety-stand sentence in their maintenance precautions. A pad job keeps the car up much longer, with a wheel off. That is why this page is stricter than any single sentence below.

Hyundai Elantra 2023 — "Never place any portion of your body under a vehicle that is supported by a jack." The jack label adds: set the parking brake, stop the engine, firm level ground
Never under a jacked car
Chevrolet Equinox 2026 — "Never get under a vehicle when it is supported only by a jack."
Not under a jack alone
Nissan Rogue and Infiniti QX60 — "Never get under the vehicle while it is supported only by the jack. If it is necessary to work under the vehicle, support it with safety stands."
Safety stands
Subaru Outback 2022 and 2024 — "Never get under the vehicle supported only by a jack. Always use safety stands to support the vehicle." Its flat-tire section adds: "Contact a SUBARU dealer when jacking up the vehicle using a garage jack."
Safety stands
Toyota Camry Hybrid — "Use a jack stand if it is necessary to get under the vehicle." Also: do not start the hybrid system while the car is on the jack
Jack stand
Mercedes-Benz C-Class 2022 — the jack is not for "maintenance work under the vehicle"; "Never lie under the vehicle."
Jack is not for work under
MINI Countryman 2025 — "do not lie under the vehicle" with it raised on the jack; "Do not place supports under the jack."
No blocks under the jack
Mazda MX-5 2023 — "Never go under the vehicle while it is jacked up"
Never go under
Volkswagen Tiguan — "Never start the engine when the vehicle is jacked up."
Engine off

Mercedes-Benz says its jack "is only designed for raising and holding the vehicle for a short time while a wheel is being changed and not for maintenance work under the vehicle." Nissan and Subaru name the alternative: safety stands. Subaru's manuals go further: "Contact a SUBARU dealer when jacking up the vehicle using a garage jack." On a Subaru, ask a dealer first.

Never get under a car, or work on a wheel, with the car held up by a jack alone. Lift it at the jack points in your owner's manual, set jack stands under it, chock the wheels that stay on the ground, and keep the engine off. The manuals say "under the vehicle"; "work on a wheel" is this page's addition, for a job that keeps a wheel off for an hour or more. Loosen the wheel nuts first, with the wheel on the ground: Chevrolet's tire-change steps say "Turn the wheel wrench counterclockwise to loosen all the wheel nuts, but do not remove them yet." before the jack goes in.

Hyundai's jack label says to use the jack on "firm level ground", and Hyundai and Nissan say not to leave anyone inside the car on the jack. The lifting points are in your manual.

Wheel off: look before you unbolt anything

With the wheel off you can see what the pads were telling you, and the papers give a short list of what to check before a bolt comes out.

Pads, rotor and lines. Nissan's maintenance list: "Brake pads and rotors: Check for wear, deterioration and fluid leaks. Replace any deteriorated or damaged parts immediately." And for lines: "Check for chafing, cracks, deterioration, and signs of leaking." Brembo: "If the disc surface shows cracking or deep streaking, replace the disc." Wagner says to compare the rotor's minimum thickness with the maker's specification, and to replace it if it is not within it. What a shop charges, and how the rotor decision is made, are in our rotor replacement cost guide.

Caliper, guides, bearing. Brembo: "Check brake caliper, all other moving parts and sliding/guide elements to ensure they are not worn out and are working properly." For fluid on a caliper: "If there are signs of fluid contamination or other damage to the caliper, replace it with a new caliper." A caliper wet with fluid points to a leak, which is a stop case from the first section. Brembo also says: "Check all steering and wheel suspension elements as well as wheel bearings for play and wear." Our guide to grinding noise when braking lists the wheel bearing among the causes of a noise people take for the brakes.

What is left of the pad. The numbers makers print for "worn out" differ, and this page does not choose between them; when pads are due is the subject of our guide on when to replace brake pads.

Brembo installation instructions (pad maker) — "If the thickness of friction material remaining on a pad is less than 2 mm or the wear indicator releases, replace all the pads on an axle."
2 mm
Subaru Outback (specifications) — "Brake pad wear limit" 0.06 in (1.5 mm)
1.5 mm (0.06 in)
Toyota Camry Hybrid (specifications) — "Brake pad wear limit" 0.04 in. (1.0 mm)
1.0 mm (0.04 in)

Brembo's 2 mm is from its installation instructions; our guide on when to replace brake pads quotes another Brembo page that says about 3 mm, and this page does not reconcile the two. Brembo adds "or the wear indicator releases, replace all the pads on an axle." Hyundai says "Always replace brake pads as complete front or rear axle sets.", Chevrolet "Brake pads should be replaced as complete axle sets.", Brembo "The pads must always be replaced throughout the vehicle axle." Replace the pads on both wheels of an axle together, never one side only.

Caliper and old pads out, one side at a time

Brembo's caution on the order of work: "Complete the installation on one side of the axle before beginning installation on the other side of the axle." And: "Install one brake at a time." The other side is a visual comparison for how the parts go back. Also: "Note the position of all the components disassembled or partially disassembled to ensure correct refitting."

Two warnings come before the first bolt: "Never apply the brake pedal or parking brake when working on the brake system, as this may cause damage to the system." And: "During all the operations described, the caliper liquid inlet hose must NOT be disconnected."

Brembo prints two routes, depending on caliper design. In the first, the caliper stays on the car and the pads come out of it:

  1. Remove the dust cap cover, if provided.
  2. Disconnect the wear indicator connector, if provided. Take off the retaining clips, fixing pins, springs or screws that hold the pads. Brembo warns that "The springs that retain-push the pads are under load; they must be released in a controlled manner".
  3. On a fixed caliper, extract the pads, using a retractor if necessary. On a floating caliper, push the caliper body against the support, remove the pad on the piston side first, then push the body toward the disc until the other pad comes out.
  4. Check the plates and replace them if damaged; inspect any shims and replace them if worn or damaged.

In the second route the caliper is partly taken apart: unscrew its fixing screws or guides and extract the pads. A hanging caliper hangs from the chassis: "Hook the caliper to the vehicle chassis by mean of appropriate supports so as to prevent damage to the flexible hose."

Which screws come out depends on the caliper; Brembo says only "According to the caliper configuration, disassemble or unscrew the fixing screws/guides etc." Which route applies depends on the caliper too, which is why Brembo says: "These assembly instructions are a general guide that can vary from one braking system to another. Please also follow the instructions provided by the vehicle and/or caliper manufacturer." If your car has a wear sensor, Chevrolet's Equinox manual adds that its pad life sensors "must be replaced at the same time as the brake pads."

Pushing the piston back: the fluid, the paint and the screw-type piston

This is where the brake fluid enters the job.

The level goes up. Brembo: "Open the brake fluid reservoir cap, checking the fluid level. The retraction of the pistons described below causes an increase in the brake fluid level in the reservoir. Ensure that the fluid level is not such as to cause a leak which would damage the painted parts of the vehicle." Hyundai: "Do not allow brake/clutch fluid to contact the vehicle's body paint, as it will result in paint damage." Open the reservoir cap before you push the pistons back, watch the level, wipe up any spill at once, and do not top the reservoir off beforehand.

Why not top it off first. The level may be low because the linings were worn; our guide on how to check brake fluid quotes the makers on that. Hyundai: "The level will fall with accumulated mileage. This is a normal condition associated with the wear of the brake linings." Chevrolet's Equinox EV manual goes furthest: "Do not top off the brake fluid. Adding fluid does not correct the issue if the linings are worn. Fluid level will return to normal when new linings are installed." and "Add brake fluid only when work is done on the brake hydraulic system." Chevrolet's Equinox manual puts the consequence in one sentence: "If fluid is added when the linings are worn, there will be too much fluid when new brake linings are installed." The makers do not all say the same for ordinary use: Hyundai says "If the level is low, add fluid to the MAX level." For the pad job this page follows Chevrolet on not topping off first and Brembo on watching the level, because the level rises when the pistons go back; Brembo's danger notice says to keep the level between the minimum and maximum marks at all times, and its operating checks say to top up after the job if necessary. If the level is already below the minimum before you start, stop: Chevrolet says low fluid may be lining wear or a leak, and Subaru says that if its brake warning light comes on and the level is below the minimum mark, do not drive; treat it as the leak case in the first section.

Brake fluid is not harmless. Hyundai: "If brake fluid gets in your eyes, flush your eyes with clean water for at least 15 minutes and get immediate medical attention."

The right tool, not force. Brembo: retract all the pistons of a two- or four-piston caliper at the same time with the correct tooling, and on brakes that combine a mechanical parking brake and adjustment feature, bring the pistons back by turning them or by the adjustment screws. Keep your foot off the pedal while the system is open, and do not take apart plates or caps that are firmly connected to the piston (Brembo).

Cleaning and lubricating: where the grease goes and where it never goes

On this step the two pad makers we read give different instructions. We cannot tell from the papers which fits your car, so this page sets them side by side. If your pads came with a sheet, follow it together with your car maker's and caliper maker's instructions, and where they disagree, do not guess: ask the caliper maker or a shop. Hella's page says "The enclosed assembly instructions must also be followed in the same manner as the special repair instructions of the vehicle and brake manufacturers."

Brembo. Clean the pad seat with a damp cloth, and the bracket, caliper body and guides with a non-mineral-oil detergent, but "Do not remove grease from guides and springs that require specific lubrication for correct operation." "If the kit includes a sachet of grease, apply the grease only on the side of the metal part of the pads and /or on the back of the pads, as indicated by the vehicle manufacturer." For floating calipers: "if necessary, moisten the caliper body slide guides with the enclosed grease, and follow the directions of the vehicle or caliper manufacturer." And: "Ensure that the friction surfaces do not become greasy".

Wagner. Wash all rotors, including new ones, with soap and hot water; remove rust from caliper brackets and guides with a wire brush or blasting; lubricate metal-to-metal contact points with molybdenum disulfide lube, guide pins to boots with silicone lube, and the pad-to-piston area of a shimmed pad; and "DO NOT lubricate or apply any compounds on the backing plate of Wagner TQ® with Integrally Molded Insulator (IMI™)". Its page on chemicals says, for the back of a pad shim: "Chemical compounds such as moly lube or other products that have a petroleum base should not be used." On the same page the caliper rails get moly lube and the guide pins silicone lubricant, because moly lube or petroleum products "will adversely affect the rubber guide pin boots."

Where they agree. Nothing petroleum-based on rubber. Brembo also says the friction surfaces must stay free of grease and the pads must move freely; Wagner warns that too much grease smears onto the rotor. Wagner: a petroleum-based grease on the piston dust boots makes them "swell up causing the brake pads to hang on the rotors which can cause brake drag." Brembo: "Once the pads have been fitted, they must be able to move freely in their seat."

Where they differ. Wagner says to wire-brush or blast rust from brackets; Brembo warns against hard brushes. Brembo greases the metal back of the pad, as the vehicle maker indicates, and, if necessary, the slide guides of a floating caliper; Wagner lubricates the rails, the guide pins and the pad-to-piston area of a shimmed pad; its own pages differ on moly lube for guide pins (the service checklist allows approved moly lube, the chemicals page rules it out). So work from the papers that came with your pads and your car.

Wipe, do not blast. Brembo: "Do not clean the braking system components with compressed air, hard brushes or similar." The dust section below adds the workplace rule.

Electric parking brakes: why the rear axle may be a shop job

Some cars apply the parking brake with a switch and a motor, an electric parking brake or EPB, instead of a lever and a cable. Brembo describes calipers that combine a mechanical parking brake with the adjustment of the piston (it does not say whether motor-driven ones are included), and on those calipers pushing the piston back is not the simple step described earlier. The documents we read are thin here, and the thinness is itself the finding.

The owner's manuals. We searched all 18 for the parking brake together with the words service, replace, dealer, workshop, pad, piston, retract and adjust. None prints a way for an owner to put an electric parking brake into a service position or to retract its piston. What they print are fault instructions, wheel-change steps that say to apply the parking brake before raising the car, and one raised-car warning; none is a pad-service instruction. Subaru, for a brake that will not release, under "If the Electronic Parking Brake Cannot Be Released": "Contact your SUBARU dealer and have your SUBARU dealer release the electronic parking brake." Chevrolet, for a warning light: "there is a problem with the Electric Parking Brake. Take the vehicle to a dealer as soon as possible." Mercedes-Benz, with the car raised: "Do not start the vehicle and do not release the electric parking brake."

The pad makers. Brembo: "For brakes that combine a mechanical parking brake and adjustment feature, the pistons must be brought back to their original position by turning manually or by means of adjustment screws, depending on their type." And: "For calipers with parking brake or with system for automatic recovery of clearance – Operate a few times to restore the usual clearance (return). Follow the directions of the vehicle or caliper manufacturer." Hella says some pad sets carry instructions about "the necessity of a diagnostics device". No pad maker we read says how to retract an electric parking brake piston.

Scan-tool makers sell a function for this job (see our review of Autel's tools); it is not a procedure for yours.

Subaru's battery sentence. In its caution about replacing the pad, Subaru recommends disconnecting the battery, calls that dangerous in the next sentence, and recommends its dealer. It does not say why.

The rule on this page follows. If the car has an electric parking brake on the axle you are working on, hand the job to a shop. If you cannot tell which axle carries the parking brake, treat the axle as having one. Do not apply or release the electric parking brake while the brake system is open. That is this page's rule: Brembo's caution covers applying it, and Mercedes-Benz says not to release it with the car raised. Hyundai's jack label says to set the parking brake when using the jack, and Brembo says never to apply it while working on the brake system; on an axle with an electric parking brake both cannot be followed, which is one more reason it is a shop job.

Hybrids and electric cars: what the manuals say and what they leave out

Five of the manuals we read are for such cars: the Toyota Camry Hybrid, the Hyundai Elantra Hybrid, the Nissan LEAF, the Chevrolet Equinox EV and the Mercedes-Benz EQS. The MINI Countryman manual also describes mild-hybrid versions, and the Mercedes-Benz C-Class manual describes versions with a 48 V on-board system whose high-voltage components, it says, must be worked on at a qualified specialist workshop; if your car is any kind of hybrid, treat it under this rule. This page's cautious rule is: if the car is a hybrid or an electric car, hand the job to a shop. It is our rule, not a maker's ban; here is the evidence for it, and against it.

None of these five manuals forbids a pad change. The high-voltage parts that the Toyota and Nissan manuals list (battery, motor, inverter, compressor, service plug, orange cables) do not include the brakes. Toyota's pad sentence is the same dealer sentence as for any car, and the LEAF's pad-wear warning has the same words as the Rogue's.

Toyota, Nissan and Chevrolet say never to touch the high-voltage system. Toyota: "Never touch, disassemble, remove or replace the high voltage parts, cables or their connectors." Nissan's LEAF manual: "Never touch, disassemble, remove or replace high-voltage parts and cables as well as their connectors". Chevrolet's Equinox EV manual: "The high voltage components in the vehicle can only be serviced by technicians with special training." and "High voltage cable or wiring has orange covering." A pad job does not need those parts; the manuals' point is that they are not for owners. Chevrolet's Equinox EV manual adds a warning for any service with a wheel off the ground: "Unexpected wheel motion and/or direction when one or more wheels are off the ground for service work may result in injury." It says to turn the vehicle off or place it in Service Mode before lifting.

The brakes work differently. Hyundai's hybrid manual says that when the regenerative brake does not operate, "The operation of the brake pedal may be more difficult than normal and the braking distance may increase." The service bulletins quoted in our guide on how to bleed brakes name special tools or scan tools for several hybrids and electric cars.

Because the owner's manuals say nothing about how the friction brakes of these cars are serviced, and Brembo, DBA and Hella say they write for professionals, this page treats these cars as a shop job. If your manual or the maker's service information describes a pad change as an owner's job, that comes before this page. We found none that does.

Putting it back: pads, springs, caliper and the order Brembo prints

Brembo's instructions have you reverse the removal steps. These are the points it adds, with Wagner's where Wagner has one.

  1. Pads the right way round. Brembo: "The pads must be inserted with friction material facing the disc." For directional pads the arrow "indicates the vehicle forward rotation"; directional pads without markings go back in the position of the original. Wagner's page on the D-1414 pad says its sets have an inboard pad (two humps on the backing plate) and an outboard pad (smooth arched backplate); swapped, you can get a soft pedal, a hard pedal, or a wheel that binds and overheats.
  2. Springs, pins, clips and the wear indicator. "Check the correct positioning of any springs in the pad seats." "Ensure correct fixing of the pads." "If present, reconnect the wear indicator cable." And "Once the pads have been fitted, they must be able to move freely in their seat."
  3. Caliper screws to the maker's number. "Refit the caliper and tighten the fixing screws, applying the closing torque prescribed by the vehicle manufacturer." For a caliper with radial fitting, it says to tighten the screws by hand, operate the brake a few times, then tighten to the prescribed torque, which pulls against its caution never to apply the brake pedal or parking brake when working on the brake system. The instructions do not reconcile the two; follow your caliper maker's.
  4. The other side, the same way, one side at a time, then refit the wheel following the vehicle manufacturer's instructions.

The caliper torque is the missing number. None of the 18 owner's manuals prints a torque for the caliper bracket or slide-pin bolts. The word caliper appears from none to four times in each, and never beside a torque figure. Brembo: "As a general rule, closely follow the instructions contained in the original literature of the vehicle manufacturer. Do not use an impact screwdriver, observe torques, always replace self-locking screws/nuts/safety elements." Chevrolet, on its pad life sensors: "See the Service Manual for replacement instructions." Chevrolet's Equinox EV manual says "If doing some of your own service work, use the proper service manual." and "To order the proper service manual, see Publication Ordering Information". We did not read any service manual, so we cannot print the number; if you do not have it for your car from the maker, the job is not ready to finish.

Wheel nuts: the torque each maker prints, side by side

The wheel nut torque is in the owner's manual, and the manuals we read print numbers from 76 to 140 lb-ft. These are examples of what is printed, not recommendations, and they must not be used for another car.

Toyota Camry Hybrid — printed as 76 ft-lbf (103 N-m, 10.5 kgf-m)
76 lb-ft (103 N-m)
Hyundai Elantra 2023 — printed as 79 to 94 lbf-ft (11 to 13 kgf-m), a range
79 to 94 lb-ft
Genesis GV70 2023 — printed as 101 to 116 lbf-ft (14 to 16 kgf-m), a range
101 to 116 lb-ft
Nissan Rogue and LEAF 2026 — printed as 80 ft-lb (108 N-m)
80 lb-ft (108 N-m)
Infiniti QX60 2025 — printed as 83 ft-lb (113 N-m)
83 lb-ft (113 N-m)
Subaru Outback 2022 and 2024 — printed as 88.5 lbf-ft (120 N-m) in 2022 and 89 lbf-ft (120 N-m) in 2024
88.5 / 89 lb-ft
Chevrolet Equinox 2026 — printed as 100 lb ft
100 lb-ft
Chevrolet Equinox EV 2026 and Silverado 1500 2025 — printed as 140 lb ft
140 lb-ft
MINI Countryman 2025 — printed as 101 lbs ft/140 Nm
101 lb-ft (140 N-m)
Mazda MX-5 2023 — printed as 108-147 N-m (80-108 ft-lbf), a range
80 to 108 lb-ft
Volkswagen Tiguan — printed as 140 Nm (103 ft-lbs) for steel or alloy wheel rims
103 lb-ft (140 N-m)
Mercedes-Benz C-Class 2022 — printed as 111 lb-ft (150 Nm) after a first tightening to a maximum of 59 lb-ft (80 Nm)
111 lb-ft (150 N-m)

Lower the car so its tires carry its weight, then tighten the wheel nuts or bolts with a torque wrench to the number in your owner's manual, in a criss-cross pattern; never use an impact wrench on them above its lowest setting, and never oil or grease the threads. Chevrolet: "The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing." Brembo's torque page: "To ensure good contact between the wheel, the brake disc and the hub, it is advisable to carry out a “star” tightening sequence, which is tightening first nut and then the one opposite (instead of the next one along)." It warns that too low a torque can loosen the wheel bolts and too high a torque can deform the brake discs or break the bolts. Mercedes-Benz: "Never oil or grease the threads." and "Only tighten wheel bolts or wheel nuts when the vehicle is on the ground."

Recheck them. Nissan and Infiniti: after about 600 miles (1,000 km); Hyundai: after 620 miles (1,000 km). Volkswagen: "should be checked with a correctly functioning torque wrench immediately after changing a wheel." Do what your manual says, and do not skip the first check.

Before the car moves: the pedal, the fluid and the lights

With the wheels back on and the car on the ground, the job is not finished. Brembo's operating checks give the order:

  1. Check the fluid level. If it is low, Brembo says to top up with new fluid of the grade specified for the vehicle, as far as the maximum mark, following the vehicle manufacturer's instructions; Chevrolet's Equinox EV manual says not to top off, because the level returns to normal when new linings are installed. Follow your maker.
  2. Clean the cap and close it; clean up any spilled fluid with a damp cloth.
  3. Press the pedal to seat the pads: "Repeat this operation until the lever/pedal stroke has stabilized at approximately 1/3 of the total stroke. When a constant force is applied, the lever/pedal stroke should not change even after a long period."
  4. "If the pressure or pressure stability are not obtained, re-check the entire braking system. Under these conditions the brake cannot be used." And: "Re-check the braking system for leaks."
  5. Check that the brake lights come on when the pedal is pressed and that any wear-sensor connector is plugged back in; Brembo: "If the vehicles’ brake lights do not come on, do not operate the vehicle".
  6. Then test at low speed, where no vehicle follows you, and check that there is no noise or vibration from the brakes (Brembo: "Road test the vehicle, taking care not to stab at the brakes or keep the pedal depressed for more than 3 seconds; make certain there is no noise or vibration from the brakes.").

Before the car moves, press the brake pedal several times until it is firm. If the pedal is soft, sinks, or stays low, or the red brake warning light stays on, do not drive the car: have it towed. Brembo says the brake cannot be used. For a red brake warning light that stays on, Chevrolet's manuals say to have the vehicle towed; for a soft or sinking pedal the tow is our rule, the same one our pages on bleeding brakes and checking brake fluid print for a soft pedal.

The level will fall slowly as the pads wear down over the miles, which Hyundai, Toyota and Volkswagen all describe as normal; Brembo's danger notice says it must at all times be between the minimum and maximum marks.

Bedding in: what each source prints, and why the answers differ

New pads and rotors have to wear into each other. Mercedes-Benz, Volkswagen and Brembo say braking is weaker until they do; MINI says break-in avoids brake noise; Wagner, DBA and Power Stop describe it as seating the pads. They do not agree on what to do about it: the car makers and Brembo say to drive gently for roughly 125 to a few hundred miles (Subaru says 1,000), and Wagner, DBA and Power Stop print stop-and-cool routines. They do not average into one number, so here they are as printed.

Chevrolet Equinox and Equinox EV — avoid hard stops for the first 300 km (200 mi) or so, 322 km (200 mi) in the EV manual
Avoid hard stops, 200 mi
Subaru Outback — the break-in driving rules for the first 1,000 miles (1,600 km) also apply when brake pads are replaced; "Avoid hard braking, except in an emergency."
Avoid hard braking, 1,000 mi
Mercedes-Benz C-Class (new or replaced pads, discs, tires) — full braking effect only "after several hundred kilometers of driving"
Several hundred km
MINI Countryman — "Drive carefully for the first approx. 300 miles/500 km."
300 mi / 500 km
Volkswagen Tiguan — 200 to 300 km (100 bis 200 miles) in one paragraph; 300 km (200 miles) in the warning
300 km (200 mi)
Brembo (if the car maker gives none) — at least 200 km / 125 miles, brakes applied gently and sparingly
200 km / 125 mi, gentle
Wagner — about 20 stops from 30 mph, or 20 slow-downs from 50 to 20 mph, 30 seconds between, no high-speed stops
20 stops or slow-downs
DBA — about 10 slow-downs from 30 mph to 5 mph, 30 seconds between; then avoid heavy braking 200 km (120 miles)
10 slow-downs, 30 to 5 mph
Power Stop (its drilled and slotted rotors) — five stops from 40 to 10 mph, then five from 35 to 5 mph
5 + 5 stops

The car makers. Chevrolet's Equinox manual: "Avoid making hard stops for the first 300 km (200 mi) or so. During this time the new brake linings are not yet broken in." Mercedes-Benz says new or replaced brake pads, discs and tires only achieve optimum braking effect after several hundred kilometers. MINI and Subaru give similar instructions, as the table shows. Volkswagen gives two figures in one manual, 200 to 300 km and, in a warning, 300 km (200 miles).

The pad makers. Wagner says an effective burnish cycle takes about 200 stops, "consistent with the burnish procedure outlined in the Federal Motor Vehicle Safety Standards FMVSS 105 and FMVSS 135", which may not be practical for many repair shops, and recommends about 20 complete stops from 30 mph or "20 “Slow-Downs” from 50-mph to 20-mph with light to moderate pedal pressure", no high-speed stops or braking under heavy loads, with at least 30 seconds between applications. DBA and Power Stop print their own routines, in the table. Brembo: "Always follow the bedding-in instructions provided by the vehicle manufacturer." Where the car maker gives none, "it is recommended to use the vehicle for of at least 200km/125miles applying the brakes gently and sparingly during that period, avoiding sudden braking for more than 3 seconds and without activating the vehicle’s Antilock Braking System."

What to take from it. The car makers and Brembo ask for gentle driving; Wagner, DBA and Power Stop describe controlled stops or slow-downs with cooling. They are not the same procedure. Follow your car maker first, as Brembo says. Do not run a performance-rotor routine on a car whose manual says to avoid hard stops; do any stop routine where no vehicle follows you, and until the pads are bedded in, leave extra distance. Our guide on best brake pads sets two makers' bedding answers against each other for people choosing pads.

The parking brake has its own break-in. Nissan's Rogue manual: "Break in the parking brake pads whenever the stopping effect of the parking brake is weakened or whenever the parking brake pads and/or calipers/rotors are replaced, in order to assure the best braking performance." Nissan says the procedure is in the service manual and recommends a NISSAN dealer. Infiniti's version is for parking brake shoes and rotors and sends you to the INFINITI Service Manual. Nissan does not say whether these parking brake pads are the rear pads you just changed, so if you changed rear pads on a Nissan, ask a NISSAN dealer whether this break-in applies. Either way, the owner's manual hands this work to a technician.

Brake dust and old parts: what the papers say, and what they do not

Brembo, as quoted earlier, says to use a respirator or other suitable equipment and not to clean with compressed air or hard brushes.

The federal rule we found is written for employers, not for a driveway. OSHA's asbestos standard, 29 CFR 1910.1001, has a mandatory Appendix F, "Work Practices and Engineering Controls for Automotive Brake and Clutch Inspection, Disassembly, Repair and Assembly", which has employers use a negative-pressure enclosure with a HEPA vacuum or a low-pressure wet cleaning method. A simpler wet method is allowed only for a facility that services no more than 5 pairs of brakes or 5 clutches a week: the parts are wetted with a fine mist of water and "Brake and clutch components shall then be wiped clean with a cloth." And: "The use of dry brushing during the wet method operations is prohibited." The standard says asbestos is used in, among other things, brake and clutch linings. We cannot tell you whether your pads contain any; the rule binds employers.

Do not blow brake dust off with compressed air or sweep it dry. Wet it and wipe it with a damp cloth.

The old parts. Brembo: "Used brake pads must be disposed according to the legal requirement applicable under national and/or local regulations." We could not read a federal page on how a household should dispose of used brake fluid or pads; your county's waste office knows what it requires.

After the job: the pad monitor, the warning lamp and the first week

A pad monitor that has to be told. Chevrolet's Equinox and Silverado manuals describe a system that estimates the remaining life of the pads. The Equinox manual: "The system must be reset every time the brake pads are changed." If the reset option does not appear, it says to drive for at least 60 seconds and try again, and to see a dealer if it still does not appear. And: "Brake pad life sensors must be replaced at the same time as the brake pads."

Squeals. Chevrolet: "Some driving conditions or climates can cause a brake squeal when the brakes are first applied, clearing up following several applications." Nissan: "Occasional brake noise during light to moderate stops is normal". Both also describe the wear-indicator sound as a different thing. Subaru: "If you hear this scraping noise each time you apply the brake pedal, have the brake pads serviced by your SUBARU dealer as soon as possible."

What should I do about a squeal or a new noise after a pad change? Start from Brembo's road test: "make certain there is no noise or vibration from the brakes." A noise that starts with the job is a reason to recheck the work or have the brakes inspected; Subaru says to have the car inspected immediately if a squeaking or scraping noise is heard while braking. Chevrolet and Nissan call a brief squeal or occasional light noise normal, but those sentences describe everyday driving, not a fresh repair. A scraping or grinding noise every time you press the pedal, a pedal that pulses or a pull to one side needs inspection. PulsCar's free sound check listens to 30 seconds of a running engine, not to wheels, so it cannot tell you anything about brake noise. Our guides on grinding noise when braking and car shakes when braking sort the causes.

Check the nuts again, and the level once more. Recheck the wheel nuts at the distance your manual prints, and check the fluid level after the first drive; see how to check brake fluid for reading the reservoir.

What a pad change does not fix

A new set of pads fixes a worn set of pads, not the rest of the system.

It does not fix a cracked or deeply streaked rotor. The rotor decision is in our rotor replacement cost guide; the cost of pads and rotors together is in brake pads replacement cost and brake fluid flush cost.

It does not fix a vibration that comes from something else. Brembo's instructions start with a test drive before any work: "Test drive the vehicle to confirm symptoms. Thoroughly inspect the connected/surrounding components." Its page on wheel torque says unevenly tightened wheel bolts can lead to vibrations at the steering wheel when braking, and Chevrolet says improperly tightened wheel nuts can lead to brake pulsation and rotor damage. After your own pad job, a pulse is worth a check of the wheel nuts first, and the page on car shakes when braking second.

It does not fix a pull or a leak. A car that pulls to one side under braking is the subject of our guide on a car that pulls to one side. A wet caliper, a cracked hose or a soft pedal is the stop-and-hand-over case from the first section.

Three ways a careful person still gets this wrong

Trap one: trusting the jack. A pad job puts the car up for a long time and takes the wheel off, so the jack in the trunk is the wrong thing to trust. The defense is the jack-stand sentence in the box at the top.

Trap two: topping off before, and a closed cap during. The reservoir may be low because the pads were worn, and the fluid goes back up when the pistons go in; Chevrolet and Brembo both warn about it. The defense is the reservoir sentence in the box at the top.

Trap three: the wrong grease in the wrong place. Petroleum-based grease on the piston dust boots can make them swell and the pads drag (Wagner), and friction material must not meet grease (Brembo). Read the sheet that came with your pads before you open the tube.

Three composite situations, decoded

These are composite scenarios, not individual customers. They are built only from the manuals and pages quoted above.

Situation one: the front pads on a car with a lever parking brake. A driver has jack stands, a torque wrench, the manual's wheel nut number and the sheet from the pad box. They lift the car at the jack points, set the stands, chock the rear wheels and keep the engine off, take the wheel off and look at the rotor, hose and guides. They open the reservoir cap, push the piston back with the tool that fits, lubricate only where the sheet says, fit the pads with the friction material facing the disc and tighten the caliper screws to the number the vehicle maker prescribes, because the owner's manual does not print it. One side at a time. They refit the wheels, lower the car so its tires carry its weight and torque the nuts in a criss-cross pattern. Once both calipers on the axle are refitted and tight, and before the car moves, they press the pedal several times until it is firm, then drive gently for the distance the manual gives.

Situation two: the rear pads on a car with an electric parking brake. The owner has done fronts before. They read the sections above: no owner's manual says how to service the parking brake motor, Subaru sends the release of a stuck electronic parking brake to its dealer, and Brembo points to the vehicle or caliper maker's directions. Hand the job to a shop if the car has an electric parking brake on the axle you are working on. They book the rear axle at a shop and keep doing the fronts at home.

Situation three: the pedal that sinks. A driver finishes the fronts, lowers the car to the ground and presses the pedal: it goes lower than it should, and stays low. They do not drive. Brembo says the brake cannot be used in that state, and this page's rule is the same: have it towed. They call a tow and tell the shop what they changed.

Where a free sound check fits, and where it does not

This is our side of the page. PulsCar's free sound check asks you to film your engine running for 30 seconds and shows a free result on screen in about a minute. The home page states the terms plainly: "No payment, no card, no subscription." It has no role in a brake pad job, and we do not offer it for one. For a noise from the brakes, the steering or a wheel, or for any red or flashing warning light, the car needs a mechanic's inspection first, not a recording: pull over safely, switch the engine off, and have the car inspected before it is driven on.

Can a free sound check tell me whether my brake pads are worn out, or whether I fitted new ones correctly? No. PulsCar's free sound check listens to about 30 seconds of an engine that is running and says nothing about thickness of friction material, a seized slide pin, a cracked rotor or a loose wheel nut, and a squeal or a grind from a wheel is a brake inspection question. What does answer it: the wear limits the makers print, the wear indicator's noise as the makers describe it, and a look at the pads with the wheel off. Where a free check may help is with something else you notice on the same drive: a new engine sound. For anything from the brakes, the steering or a wheel, inspect first and record later.

What we looked for and did not find

  • A pad-change procedure in an owner's manual. None of the 18 prints one. The steps here come from the pad makers.
  • A torque for the caliper bracket or slide-pin bolts. None of the 18 prints one. Brembo says to use the one the vehicle manufacturer prescribes; we did not read any service manual.
  • A way to retract an electric parking brake piston. Neither the manuals nor the pad makers describe one.
  • Many of the biggest makers. We could not read the manuals of Tesla, Ford and Honda (a refusal or a service error) and did not get around them; we did not look for Jeep, Ram, BMW or Volvo.
  • Editions. Volkswagen's manual is the English (en_GB) edition 11.2021, read on Volkswagen India's site, and Brembo's instructions come from its European site.
  • Federal pages on jack stands, household brake dust and used brake fluid. We found none to quote; the EPA page we tried returned an error. OSHA's brake-dust rule does not apply to a driveway.
  • A measurement. We changed no brakes, tested no pad and measured nothing.

What could we not read for this page, and does PulsCar fill the gap? We could not read the owner's manuals of Tesla, Ford and Honda, because their sites answered with a refusal or a service error, and we did not get around either of those answers. PulsCar's free sound check, which listens to 30 seconds of an engine running, says nothing about brake pads, jack points or torque. If you drive one of those cars, the best use of this page is the list of questions it asks: who your manual says should replace the pads, where the jack points are, what torque the wheel nuts take, whether the parking brake is electric, and whether a pad monitor needs a reset. Your own manual answers them, and the pad box answers the rest.

Your action plan: before, on the day, and after

Before (an hour with the manual, not the car).

  1. Open your owner's manual: jack points, wheel nut torque, anything on the parking brake, the brake fluid and the pads. Decide whether this is your job. Hand the job to a shop if the car has an electric parking brake on the axle you are working on, if it is a hybrid or an electric car, if your car maker's manual or service information says a dealer or technician should replace the pads, or if you have no jack stands or no torque wrench.
  2. Get the caliper-bolt torque from the vehicle maker's service information and read the sheet in the pad box; both come before this page.
  3. Gather a jack, jack stands, chocks, a torque wrench, the right piston tool, new hardware, cleaner, the right lubricants, gloves and a respirator.

On the day.

  1. With the car on the ground, loosen the wheel nuts about one turn, as Mercedes-Benz and Volkswagen print. Never get under a car, or work on a wheel, with the car held up by a jack alone. Lift it at the jack points in your owner's manual, set jack stands under it, chock the wheels that stay on the ground, and keep the engine off.
  2. Take the wheel off and look at the pads, rotor, caliper, guides, hose and wheel bearing before you unbolt anything. A wet caliper or a cracked or deeply streaked rotor is a stop.
  3. Brake fluid strips paint and irritates eyes and skin. Open the reservoir cap before you push the pistons back, watch the level, wipe up any spill at once, and do not top the reservoir off beforehand.
  4. One side at a time. Hang the caliper from the chassis, not from the hose. Fit the pads friction side toward the disc with the hardware and lubricants your sheet names. Replace the pads on both wheels of an axle together, never one side only. Refit the caliper to the vehicle maker's torque.
  5. Do not blow brake dust off with compressed air or sweep it dry. Wet it and wipe it with a damp cloth.
  6. Lower the car so its tires carry its weight, then tighten the wheel nuts or bolts with a torque wrench to the number in your owner's manual, in a criss-cross pattern; never use an impact wrench on them above its lowest setting, and never oil or grease the threads.
  7. Refit and tighten both calipers on the axle first. Then, before the car moves, press the brake pedal several times until it is firm. If the pedal is soft, sinks, or stays low, or the red brake warning light stays on, do not drive the car: have it towed.

After.

  1. Drive gently for the distance your car maker prints and leave extra distance.
  2. Recheck the wheel nuts at the distance your manual prints, check the fluid level after the first drive, and reset the pad monitor if your car has one.
  3. If you hear scraping each time you press the pedal, or feel a pulse or a pull, have the brakes inspected. If a red or flashing warning light comes on, or the brakes or steering feel wrong: pull over safely and switch the engine off; have the car inspected before it is driven on. If it is the red brake warning light, or the pedal is soft, do not drive: have the car towed.

Sources and documents

The facts on this page come from the pages below, read on 11 and 12 November 2026 and saved as text; advice marked as ours is ours. Quotes are as printed.

Prices verified: this page prints no prices. Technical documents verified 11 and 12 November 2026: owner's manuals, brake makers' installation pages and bulletins, a federal workplace rule and a roadside-club page. Written by PulsCar, which makes the free sound check.