🚨 60-Second Triage — P0107 means the engine computer sees the MAP sensor's voltage as too low; the papers mostly point at a wire, a plug or a supply fault before the sensor. P0107 with a stall, lost power, a stop message or a flashing light: If the car has stalled, lost power, shown a reduced-power or stop message, or failed to restart even once, or if the check engine light is flashing, do not drive on: pull over safely, switch the engine off and have the car towed. That is our advice, not a maker's. The only exception, a flashing light alone on a car that starts and runs normally, is a shop within 2-3 miles, reached gently, at 31 mph (50 km/h) or less with light throttle. No maker paper we read about P0107 itself says to stop driving; Ram's 2026 manual says of a flashing lamp "Immediate service is required" and Chevrolet's says to find a safe place to park if the light keeps flashing. A steady light and a car that drives normally: have it diagnosed soon, within days rather than weeks (our advice, looser than the 1999 Toyota manual, an unofficial copy: "as soon as possible"). P0107 with P0641, P0106 or several other sensor codes at once: suspect something the sensors share, a wire, a ground or the 5-volt supply, before any sensor; GM's paper for 2016 full-size trucks and SUVs, Subaru's for the 2012-2014 WRX and Mercedes' for the M274 engine each trace several codes to a harness or ground fault. A 2018-2019 Explorer, Flex, Taurus or MKT with the 3.5L EcoBoost and P0107, P0108 or P0109: ask a Ford dealer about bulletin 19-2212. A 2019-2021 Silverado or Sierra 1500 with the 2.7L engine, or a 2019-2020 one with the 4.3L, and a long list of codes including P0107: ask a GM dealer about PIT5677E or PIT5713A, harness inspections. A 2012-2014 Subaru WRX (not STI) or 2012-2013 Forester Turbo that sets P0107 now and then: Subaru bulletin 07-96-15 covers a ground point.
P0107 is a voltage word, not a part word, and that changes where you look first.
P0107 — printed on a Jeep service page copy as "P0107-MANIFOLD ABSOLUTE PRESSURE SENSOR CIRCUIT LOW" and by Saab as "Manifold Absolute Pressure (MAP) Sensor Circuit Low Voltage" — says the engine computer is receiving a signal from the manifold pressure sensor that is below the lowest value it allows. The sensor sits on or near the intake manifold and tells the computer how much air pressure is in the intake, so it can work out how much air the engine takes in and how much fuel to add. A signal that is too low looks, to the computer, like a pressure at the very bottom of the scale.
This page answers one question: is a low MAP signal the sensor, its wiring and connector, or something else, can I drive, and what does it cost? The neighbour page, P0106, the MAP range and performance code, already covers the code for a reading that is in range but does not fit; this page does not repeat its findings, its complaint counts or its lists.
What we read. From NHTSA's index of manufacturer communications we read 18 files from GM (12), Ford (3), Subaru, Porsche and Ram whose own text prints P0107, in NHTSA's files through early October 2026 (papers naming it only in the body may be missing). We added three NHTSA papers about harnesses and the 5-volt supply (GM 20-NA-104, GM program N192219370 and a Mercedes-Benz tech topic) and the maker pages readable in public: a Jeep service page, Saab and Vauxhall workshop pages, a Honda Jazz page, a Volkswagen fault table, Nissan, Toyota and Mitsubishi manuals, and owner's manuals of Chevrolet, Ram and Hyundai (every page here except those three manuals is a copy hosted outside the maker's site, and none of those copies is linked). Fourteen makers and brands print the code or its circuit; six more (Hyundai, Kia, Mazda, BMW and MINI, Volvo, Jaguar and Land Rover) could not be read for this code, and the atlas below says what was tried. Only 12 complaints in NHTSA's file, received from January 2015 through October 2026, print P0107, P0108, P0109 or P0105 as the MAP circuit code, and 7 of them print P0107 in some spelling. That is too few to say how often anything happens, so this page does not turn it into a rate.
Claims marked 🟢 rest on a document listed in the Sources section. Claims marked ⚪ are shop-price estimates carried from our repair guides. Every complaint count here comes from the 12 complaints we read and published.
Words on this page. Engine computer (ECM, PCM): the car's computer. DTC: a trouble code such as P0107. MIL: the check engine light. MAP: manifold absolute pressure. MAPT: a MAP sensor that also reads air temperature. 5-volt reference: the 5-volt supply the computer gives to several sensors. Signal circuit: the wire that carries the sensor's reading back. Sensor ground (low reference): the return wire. Short to ground: a wire touching the car's body or the ground circuit, which pulls its voltage to zero. Open: a wire that is broken or a connector that has lost contact. kPa: kilopascal, the pressure unit scan tools print; about 101 kPa is the air pressure at sea level. Bulletin (TSB, PIP, PIT): a maker's repair paper for dealers, not a recall. ETC: electronic throttle control. PID: a live data item on a scan tool. EGR: a valve that feeds exhaust back into the intake. Ohm: the unit of electrical resistance.
I built PulsCar after a $380 "full diagnostic" in Phuket in 2025 led to roughly $6,000 over six months across several shops (the story is on the About page).
Is P0107 usually a bad MAP sensor, and does a new sensor fix it? PulsCar read every NHTSA complaint from 2015 to October 2026 that prints P0107 or a sister MAP circuit code: 12 of them, 7 printing P0107. In 7 of the 12 no cause is stated; 2 owners point at wiring, a dealer found an air leak in 1, an owner fitted a sensor in 1 (the outcome for the code is not stated) and a dealer said the engine had seized in 1. That is far too thin to rank causes, so the makers' papers carry the answer: in the maker pages we read, a low signal is mostly traced to the 5-volt supply, the signal wire, the sensor ground and the connector before the sensor, and only Ford's bulletin prints a plain sensor swap for P0107 (2018-2019 3.5L EcoBoost). Test the wire, the connector and the ground before you buy the part.
What P0107 means: a MAP signal below the floor, and why "low" points at the circuit
What the computer checks. 🟢 Saab's page for the 2011 9-5 2.0 turbo says P0107 sets when "the MAP sensor voltage is less than 0.19 V for more than 4 s continuously, or 50 s cumulative", and P0108 when it is "more than 4.80 V" for the same time; between them, with the ignition on, it expects a reading "between 0.20-4.80 V" (the 2011 9-5 workshop page on saabwisonline.com, a third-party site; not linked). A MAP sensor has three wires: a 5-volt supply from the computer, a ground, and a signal wire that returns a voltage between about 0 and 5 volts that rises with pressure. P0107 is the computer saying the signal wire sits at the bottom of that range. Saab and Vauxhall print the same three-wire description; Chrysler's page lists it as "5-VOLT SUPPLY CIRCUIT", "MAP SIGNAL CIRCUIT" and "SENSOR GROUND CIRCUIT".
Why low points at the circuit. 🟢 Saab prints what the sensor should read at rest: "the highest pressure that can occur in the intake manifold with the ignition ON and the engine OFF is equal to the barometric pressure (BARO)", and its idle range below. Against a normal idle reading of tens of kPa, a signal at the floor is one the engine does not normally make (our reading), and that is why the printed causes are mostly electrical. Saab's page prints a table of scan-tool readings for each fault: with the engine running in park, a normal reading is "20-48 kPa, varies with altitude"; a signal wire shorted to ground reads 0 kPa, an open signal wire reads 0 kPa, and a signal wire shorted to voltage reads 255 kPa. Vauxhall's Astra page prints the same pattern with a normal idle range of 26-52 kPa and 127 kPa for the high fault. These are maker tables for those cars, not numbers for yours.
P0107 symptoms: what you feel. Sometimes nothing but a light; often more. 🟢 Chrysler's page says that when the code sets "MIL will illuminate and the ETC light will flash if equipped"; Ford's 2019 paper for the 3.5L EcoBoost lists "an illuminated malfunction indicator lamp (MIL), powertrain malfunction (wrench) lamp, Service AdvanceTrac message, Hill Start Assist Not Available message, and/or lack of power"; Mercedes' tech topic for the M274 engine says the engine "may experience torque reduction when fault occurs"; Vauxhall's page adds that with the code set "The BARO will not be updated". Carista's P0107 page (a scan-app maker's, not a car maker's) lists rough idle, poor throttle response and worse fuel economy besides the light, and says the engine may run rich, hesitate or stall on a fallback fuel map. Among the owners who wrote to NHTSA, 8 of the 12 describe a stall and 9 a loss of power or limp mode (10 of 12 one or the other).
What it is not. It is not a mass air flow code (P0101, P0103), a lean code (P0171) or a boost code (P0299), though a failed 5-volt supply can set several of them in one drive.
First: P0107 alone, with P0108, or with a crowd of codes?
Read the whole list of codes before you buy anything, because what P0107 keeps company with tells you more than P0107 does.
Routes, explained below: 1 the plug, 2 the wire, ground and 5-volt supply, 3 the sensor, 4 the computer, 5 air and vacuum.
The numbers differ by maker. 🟢 Toyota's 1999 Camry repair manual prints this circuit as "P0105 Manifold Absolute Pressure/Barometric Pressure Circuit Malfunction", with a separate P0106 for range, and Nissan's 2000 Frontier manual prints it as "P0105 ABSOLUTE PRESSURE SENSOR"; Nissan's 2002 Maxima manual prints "DTC P0107, P0108 ABSOLUTE PRESSURE SENSOR" (all three are unofficial library copies, not linked). Search traps: in the 12 complaints owners wrote a letter O for the zero ("O0107"), a bare "0107" among a list of codes, and "P0107B".
Why P0108 shares the page. The two codes are the same circuit seen from opposite ends. 🟢 Saab and Vauxhall print them together: a short to ground on the signal or the supply gives the low code, a short to voltage on the signal wire the high one. 🟢 Chrysler's case record for a connector says "fault codes P0107- Map Sensor Circuit Low, P0108-Map Sensor Circuit High, P2172-High Airflow/Vacuum Leak Detected (Instantaneous Accumulation), P2173-High Airflow/Vacuum Leak Detected (Slow Accumulation) may be set" with one fix, the connector terminals.
The maker atlas: what fourteen makers and brands print about a low MAP signal
The papers split by maker, so find yours first: GM, Ford, Chrysler (Jeep, Ram), Subaru, Honda, Nissan, Toyota. The Saab, Vauxhall, Volkswagen, Porsche, Mercedes and Mitsubishi entries may not match your car and show how others print the same fault; Mercedes prints it on a boost sensor, Mitsubishi on a barometric sensor. Document numbers link to the NHTSA file. The Jeep, Saab, Vauxhall, Honda, Volkswagen, Nissan, Toyota and Mitsubishi entries rest on unofficial copies hosted outside the makers' sites (none of them is linked), so they show what those copies print, not a maker's current statement. Thresholds are printed on one page each.
Six brands could not be read for this code: Hyundai, Kia, Mazda, BMW and MINI, Volvo, and Jaguar and Land Rover. Their owner-manual pages gave no readable file, or were scanned with no text. The Hyundai Elantra 2023 manual we did read prints only the lamp: "Driving with the Malfunction Indicator Lamp (MIL) on may cause damage to the emission control system which could affect drivability and/or fuel economy." Nothing on this page claims what these six makers print for P0107.
What the atlas shows. Of fourteen, Ford's is the only bulletin that prints a plain sensor swap as the repair for the code (Porsche's replaces the sensors together with new cables or connectors); GM's US bulletins, Subaru, Ram and Mercedes print a wire, a ground, a connector or a short; Saab and Vauxhall test the circuits before the sensor, and Chrysler and Honda replace it at a measured step; Nissan prints the sensor as part of the computer; Toyota and Mitsubishi print the circuit under other labels. That counts papers we could read; it is not a ranking of causes.
Where the signal lives: the three wires and what each fault reads
Saab prints what the MAP signal shows for each fault with the engine running in park; Vauxhall's page prints the same logic with its own numbers. The pattern matters, not the numbers.
Reading the table. 🟢 Saab's fault table lists P0107 for a short to ground, an open and, with P0106, a high resistance on the signal wire and the 5-volt supply; P0106 and P0108 for a signal wire shorted to voltage; and P0106 alone for an open or high-resistance sensor ground. Its tests run in a fixed order: ignition off, disconnect the sensor, "test for less than 5 Ω between the low reference circuit terminal 2 and ground"; ignition on, "test for 4.8-5.2 V between the 5 V reference circuit terminal 1 and ground"; check that the scan-tool reading is below 1 kPa; then "Install a 3 A fused jumper wire between the signal circuit terminal 3 and the 5 V reference circuit terminal 1" and check that the reading rises above 254 kPa. If a circuit fails, the page sends the shop to the wire; if every circuit passes it says "test or replace the B74 MAP sensor", and at several steps it says to replace the engine computer if the circuit tests normal.
The same fault from an owner's seat. A 2010 Cobalt owner copied the codes the scan tool printed: "P0107 ENGINE (MAP) BAROMETRIC PRESSURE CIRCUIT - LOW INPUT", then an evaporative pressure sensor low, an air-conditioning pressure sensor low and "P0641 ENGINE (SENSOR REFERENCE VOLTAGE A) CIRCUIT/OPEN". Several sensors reporting low at once with a reference-voltage fault is the pattern Saab's table gives for a faulty 5-volt supply (our reading).
What each maker's steps do before they say "replace the sensor"
The papers differ on how far a shop goes before it buys a part, and that is the most useful thing a customer can ask about. The Jeep, Saab, Vauxhall, Honda and Nissan steps below come from unofficial copies hosted outside the makers' sites.
Chrysler's order is a measurement at each stop. 🟢 With the ignition on, read the sensor voltage; "Is the voltage below 0.08 of a volt?" Then unplug the sensor and measure the 5-volt supply ("between 4.5 to 5.2 volts?"). Then, with the sensor unplugged, read the signal again: "Is the voltage above 4.5 volts?"; if yes, "Replace the MAP Sensor." If not, test the signal wire for a short to ground ("below 100 ohms"), then for a short to the sensor ground, and only then the computer, after checking its connector terminals for "corrosion, damage, or terminal push out". The sensor is replaced only when that unplugged test passes; our reading is that this separates a sensor that holds the signal down from a wire that does.
Saab and Vauxhall test the circuits and name the computer five times before the sensor. 🟢 Saab's "If the circuit tests normal, replace the K20 ECM" (Vauxhall: "K20 Engine Control Module") appears after the low reference, the 5-volt reference and the signal-circuit checks; the sensor comes last with a hand vacuum pump: Saab's page wants a voltage that "should vary between 0-5 V, without any spikes or dropouts" as vacuum is applied, and Vauxhall's page prints a table, for example "at 92 kPa (13.3 PSI), the MAP Sensor scan tool reading should be between 71-79 kPa" with 17 kPa of vacuum applied. Saab's page adds a note: "You must perform the Circuit/System Testing in order to verify the integrity of the MAP sensor circuits before proceeding with the Component Testing."
Honda's order sends a scan-tool number first. 🟢 "Check the MAP with the scan tool. Is about 101 kPa (760 mmHg, 30 in.Hg) or 2.9 V indicated?" A yes ends the diagnosis as an intermittent fault. A no leads to about 5 volts at the unplugged sensor, an open wire, then "Is 2 kPa (15 mmHg, 0.6 in.Hg) or less or 0 V indicated?"; a no means "Replace the MAP sensor.", a yes leads to a short to body ground. The computer branch, reached when no 5 volts reach the computer or no short is found, opens with "Update the ECM/PCM if it does not have the latest software".
Nissan's printed order, on the Maxima pages we read, has no wire test. 🟢 On the 2002 Maxima the page has the technician erase the code, run the confirmation with the ignition on ("Wait at least 6 seconds."), and if the code returns, "Replace ECM." The sensor sits inside the computer on that model, so the part to replace is the computer.
Ford's order is a part. 🟢 For the 3.5L EcoBoost it says replace the sensor; the first version, 19-2183, had a step to monitor PID values before replacing and was replaced in July 2019. The sister page covers Ford's paper in full: the P0106 guide.
The 10-minute check
Everything here is our advice, built from what the papers test first. None of it needs more than a code reader that shows live data, and none of it should be done near moving belts or fans.
- Write down what happened. A hard acceleration, a car wash, a recent engine job, a drive in the rain. GM says a harness contact depends on engine movement and Subaru adds heat.
- Read the whole list of codes, not only P0107. P0641 or P0697 means the 5-volt supply; P0106 with it means the shared circuit; P0108 means the signal now reads high; a long list including misfire, pedal and fuel codes sends GM's papers to the engine harness; P2172 and P2173 with it send Chrysler's record to the connector.
- With the key on and the engine off, look at the MAP reading if your reader shows it. Saab says the pressure in the manifold with the ignition on and the engine off is at most outside air pressure, and Honda's page (an unofficial copy) expects about 101 kPa (the air pressure at sea level). A reading stuck near 0 kPa or 0 V when outside air should read near 100 kPa is what the low code describes (Saab's table at idle, Vauxhall's table and Honda's page).
- With the key off, look and press. The sensor's plug should click and be dry and the terminals straight. Chrysler's record says pushed-out or spread terminals; Honda's page says poor connections. Do not push meter leads into connector terminals (Chrysler warns that probing the computer's connectors damages the terminals; our advice extends that to the sensor plug).
- Only if the car has not stalled or lost power: clear the code once, drive normally, and see. A code that returns within a day is a hard fault; one that stays away is not proof, because Subaru prints that its codes may set "very intermittently with long periods of time between occurrences".
- Ask the dealer about the VIN: an open recall, a harness program or a software update for P0107?
Four P0107 situations, and which is yours
If the car has stalled, lost power, shown a reduced-power or stop message or failed to restart, the tow rule at the top comes first, in every situation below.
1. A steady light, the car drives normally, P0107 alone (routes 1, 2 and 3). Clear it once, check the plug, and ask for a measurement before a part.
2. P0107 with P0641 or other sensor codes at once (routes 2 and 4). Several sensors reporting low together point at the supply or the ground, not at four failed parts.
3. P0107 with stalls, reduced power or a long list of codes on a 2019-2021 GM 2.7L or 2019-2020 4.3L truck (route 2). GM's harness bulletins point at the engine harness.
4. P0107, P0108 or P0109 on a 2018-2019 Ford 3.5L EcoBoost Explorer, Flex, Taurus or MKT (route 3). Ford's TSB 19-2212 prints the sensor swap; one 2018 Explorer owner wrote the same list of lamps and messages and a loss of power steering.
What a P0107 repair costs: the labor the papers print, plus our shop ranges
No page we read prints a standalone price for a P0107 repair, and none of the 12 complaints states one, so this ladder shows only what the makers printed and where our own guides carry shop ranges. Part prices are not printed in any of these papers.
How much does it cost to fix P0107? PulsCar found no page that prints a price for the repair and no complaint that states one, so the honest answer is a ladder of labor, not a number. A reset or a pushed-in plug costs nothing. Ford prints 0.3 hour to replace the sensor on its 3.5L EcoBoost, GM prints 1.2 hours (a Bumper-to-Bumper warranty labor operation) to inspect and repair an engine harness, and a harness sleeve program for 2019 2.7L trucks printed 1.5 hours and ended on December 31, 2021. Our guide on how much a car diagnostic costs carries the ⚪ shop ranges for finding the fault: $80-$150 at independent shops and $120-$300 at dealers. Ask for the reading before and after the repair, and for the fault written on the invoice, before a part is ordered.
The five P0107 routes, cheapest first
A low-input code is a statement about a voltage. Each route below is a place the voltage can be pulled down or lost on its way, ordered by what it costs to rule out; routes 3 and 4 can cost more than route 2 once a part is bought. Owner counts come from the 12 complaints we read; they are single reports, not shares, and no route is a forecast for your car.
Route 1 · The plug and its terminals — $0 to a repair kit
What it is. The wire is whole, the sensor is good, and the connector between them has lost contact: a terminal pushed back out of its housing, spread so it no longer grips, corroded, or a plug that is not fully seated.
What the documents say. 🟢 Chrysler's case record for P0107, P0108, P2172 and P2173 has one discussion item: "Inspect the map sensor connector terminals at the map sensor location for possible pushed out or spread terminals (wiggle connector while checking for reading change), replace the terminals as needed, repair kit connector/ terminals (Kit 68225153AA)", with the example of a 5.7L engine and a black three-way connector (S1808000282). 🟢 Honda's Jazz page (an unofficial copy) treats a normal key-on reading as "Intermittent failure, system is OK at this time. Check for poor connections or loose wires at the MAP sensor and at the ECM/ PCM." 🟢 Vauxhall's page (also an outside copy) says, for an intermittent condition, to "move the related harnesses and connectors, with the engine operating, while monitoring the scan tool parameters". 🟢 Porsche's 918 Spyder paper blames vibration under continuous high load, such as race-track driving, that "can damage the connector contacts" and replaces the adapter piece or the connector (2480 ENU 23/14).
What the owners report. One of the 12 complaints names terminals: a 2005 Pontiac G6 owner wrote that a leaking sunroof causes "CORROSION ON THE ELECTRICAL TERMINALS IN THE WIRE HARNESS INSIDE THE DASH ON DRIVER DOOR SIDE" and that this throws PCM codes including O0107, with the car stalling and going into reduced engine power. The owner gives a theory, not a shop finding.
The cheap cause that gets skipped. A wiggle test with the live reading on a screen. Chrysler prints it in its case record and Vauxhall as a diagnostic aid; a shop that orders a sensor from the code has skipped it (our reading).
Fix it yourself. With the key off, make sure the sensor's plug clicks home and is dry, and that the terminals you can see are straight (our advice). Do not spray the plug or the sensor, and do not push meter leads into the terminals (our advice). A repair that needs new terminals needs the right kit; Chrysler prints a kit number.
At the shop — say this: "Before a sensor: was the MAP connector wiggle-tested with the live reading on screen, were its terminals checked for being pushed out or spread, and what did the reading do?"
Route 2 · The wire, the ground and the 5-volt supply — from an inspection to a harness repair
What it is. A wire rubbed through its insulation and touching metal (short to ground), a break inside the insulation (open), a ground junction that has developed resistance, or the shared 5-volt supply pulled down by one of the sensors on it.
What the documents say. 🟢 GM's paper for 2016 full-size trucks and SUVs is titled "SES Light Reduced Power With 5 Volt Reference 3 Codes", lists "P0106, P0107, P0697, P2122, P2123, P2127, P2128 and P2138", and says, if the published diagnostics are inconclusive, to inspect the harness near the left instrument-panel junction block and "Repair the damaged circuits as necessary", where a mounting stud had pinched it (PIP5344). 🟢 GM's bulletins for the 2019-2021 Silverado and Sierra 1500 with the 2.7L engine list P0107 among a long list of codes and "Erratic speedometer operation" (the later revisions add blown fuses); the first says the concerns "could be caused by the engine harness shorting to ground", the later one, PIT5677E, that they may be caused by engine harness contact with under-hood components, and warns that the engine rocks in its mounts, so a harness contact may not show when the engine is off, and prints 1.2 hours of labor (a Bumper-to-Bumper warranty labor operation) to inspect the harness and repair it (PIT5677E). The 4.3L bulletin says that because of "the number of circuits in the harness, there is a wide variety of" different symptoms (PIT5713A). 🟢 GM's customer satisfaction program N192219370 for 2019 2.7L trucks says the harness "may lead to a check engine light, reduced engine power, no start condition or in rare cases a stall" and was "in effect until December 31, 2021" (N192219370; it prints no trouble code). 🟢 Subaru's 07-96-15 says a ground junction near the turbocharger "may develop excessive resistance" and that the sensors behind its example codes, the intake manifold pressure sensor among them, share that ground: "Any increase in resistance to ground can have significant effect on these sensor outputs" (07-96-15). 🟢 Mercedes' M274 paper names a boost sensor harness touching a bracket (LI15.18-P-071185). 🟢 GM's older Colorado and Canyon paper requires "TXL wiring of the correct size along with new terminals" for sensor circuit repairs (PIP4409F; our P0106 guide covers it).
What the owners report. 2 of the 12 complaints end at wiring (the Pontiac G6 above and an Azera), and 2 GM cars print P0641, the reference-voltage fault, next to P0107. A 2009 Hyundai Azera owner wrote that after a new MAP sensor "PROBLEM PERSISTED WITH P0108 CODE" and that, under the fabric wrap on the wire bundle that holds the oil pressure, MAP sensor and engine temperature sensor wires, "ALL WIRING INSULATION HAS DISSENTIGRATED CAUSING SHORT CIRCUITS AND BAD MAP SENSOR VOLTAGE". A 2010 Chevrolet Cobalt owner wrote that the codes included "P0641 ENGINE (SENSOR REFERENCE VOLTAGE A) CIRCUIT/OPEN" and that "I WAS ABLE TO CLEAR OUT ALL CODES EXCEPT FOR P0641 (PERMANENT)".
The cheap cause that gets skipped. The reference. When P0107 arrives with other sensors reading low at the same moment, the shared supply or ground is the cheap thing to check first (our advice).
Fix it yourself. Not the wire. A repair needs the right wire and terminals, and a bad splice creates the fault you are chasing (our advice). GM's older paper above requires new terminals, and Chrysler says not to probe the computer's connectors.
At the shop — say this: "Do you see other sensors reading low at the same time, and was the 5-volt supply and the sensor ground measured under load? Please check the engine harness at its rub points, with the engine rocked, before a sensor is ordered, and write down what you found."
Route 3 · The sensor itself — a part, 0.3 hour of printed labor on a Ford
What it is. The sensor is the part that holds the signal down, so a new one fixes it.
What the documents say. 🟢 Ford prints the replacement for its 3.5L EcoBoost: "DTCs P0107, P0108 and/or P0109 present. This may be due to a faulty manifold absolute pressure and temperature (MAPT) sensor. To correct the condition, follow the Service Procedure to replace the MAPT sensor", for 2018-2019 Explorer, Flex, Taurus and MKT; 0.3 hour; part AA5Z-9F479-E (TSB 19-2212, reason for the update "Incorrect Procedure"; the first version is 19-2183). 🟢 Chrysler replaces the sensor when its signal reads above 4.5 volts with the sensor unplugged. 🟢 Honda replaces it when, after its voltage checks, the reading is not 2 kPa or less, or 0 volts. 🟢 Saab asks for a smooth 0-5 V sweep under applied vacuum and "replace the B74 MAP sensor" if it spikes or drops out; Vauxhall asks the reading to fall by the vacuum applied within 4 kPa (Jeep, Saab, Vauxhall and Honda: unofficial copies). 🟢 Porsche replaces the sensors together with new adapter cables or connectors (2480 ENU 23/14).
What the owners report. Two cars got a new MAP sensor. A 2009 Azera owner wrote that a shop replaced it: "SHOP SAID MAP SENSOR WAS BAD, REPLACED WITH NEW SENSOR. PROBLEM PERSISTED WITH P0108 CODE IN DRIVEWAY IDLING"; the owner then found the wiring. A 1996 Accord owner whose car would not move at a red light read P0401 and P0108, cleaned the EGR valve and fitted a new MAP sensor; the car then started but would not get into gear, a specialist suspected the transmission, and the complaint says nothing more about the code. A 2018 Explorer owner, whose car shows the lamps and loss of power Ford's paper describes, was towed to a dealer; the complaint does not say what was done.
The cheap cause that gets skipped. The measurement that decides it. Saab's page warns a shop to do the circuit tests first: "You must perform the Circuit/System Testing in order to verify the integrity of the MAP sensor circuits before proceeding with the Component Testing."
Fix it yourself. A sensor that unplugs from the manifold may be within a home mechanic's reach on some cars, but only after a measurement or a bulletin points at it, with the engine off and cool (our advice).
At the shop — say this: "Is the sensor replacement based on a measurement, such as the reading with the sensor unplugged, or on a bulletin for my engine? Please write the reading before and after, and tell me what else was checked first."
Route 4 · The computer, its 5-volt output and its software — Nissan's part is inside it
What it is. The computer's own 5-volt output has failed, its connector has a bad terminal, or, on some models, the sensor is inside the computer.
What the documents say. 🟢 Nissan's Maxima manual (an unofficial copy) says "The absolute pressure sensor is built into ECM" and, if the 1st-trip code returns after the confirmation, says "Replace ECM." 🟢 Saab prints "If the circuit tests normal, replace the K20 ECM" at several steps, and Vauxhall prints the same step with "Engine Control Module". 🟢 Chrysler's last step says to check the computer's connector terminals for "corrosion, damage, or terminal push out" and then "Replace and program the Powertrain Control Module". 🟢 Honda says "Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck."
What the owners report. A 2007 Saturn Aura owner, whose codes included 0641, 0107 and 0106, wrote that the dealer "RESET THE CODES AND UPDATED THE ECM", that the lamp and reduced power came back the next night with a stall, and that the dealer then said the engine had seized; the complaint does not tie that to the codes.
The cheap cause that gets skipped. The computer's connector terminals, and the question whether the circuit tests passed before a computer is ordered. Computers need programming; Chrysler prints the check of the terminals and Honda the software update before a replacement.
Fix it yourself. No; this is a shop job (our advice).
At the shop — say this: "Did the 5-volt supply, the signal wire and the sensor ground all pass before a computer was ordered, and is there a newer software version for my VIN?"
Route 5 · Air, vacuum and the engine itself — not the usual home of a low code
What it is. A hose, a leak or an engine problem that changes the pressure the sensor reads. This route is last because the low code is a floor, not a ceiling (our reading).
What the documents say. 🟢 Saab's page puts the normal idle reading at 20-48 kPa and the key-on, engine-off reading at outside air pressure at most; our reading is that a leak, which adds pressure, therefore pushes the reading up and sets the high or range codes, not the low one. 🟢 Nissan's 2000 Frontier manual (an unofficial copy) lists hoses between the manifold and the sensor, and "Intake air leaks", next to its condition of a high voltage under light load, and a MAP/BARO switch solenoid among its checks. 🟢 Chrysler's record puts P2172 and P2173, the airflow and vacuum leak codes, in the same list as P0107 and P0108, and sends a shop to the connector. 🟢 Vauxhall lists "The BARO will not be updated" as the action when the code sets, so the computer's outside-air value is not refreshed while the code is set.
What the owners report. 1 of the 12 complaints ends at air: a 2017 Sonata hybrid owner pulled P0105 and P0107 and wrote that the dealer found an EGR pipe separated from its flange, an unmetered air leak. The owner does not say which code the leak explained, and P0105 is the general circuit code.
The cheap cause that gets skipped. A hose that is off or split. Look at the hoses and ducts with the engine off, and check that any vacuum line to the sensor is on both ends (our advice).
Fix it yourself. A visible hose or duct that is off or cracked is a part and a clamp in our guides (⚪ about $15 to $40, from the P0171 guide); leave manifold work to a shop.
At the shop — say this: "If air or vacuum was blamed for a low-input code, can you show me the live reading changing when you fix it? A leak should push the reading up, not down."
The coverage file: which papers and programs still run
Status "as of November 2026" is our computation from the printed terms. A program is not a repair of your car until a dealer has done it and written it down; ask by VIN.
No recall prints P0107. We searched the text of NHTSA's recall table for the code and found none. The nearest recalls, Ford 14V495 (2013-2014 Escape) and 15V813 (2013 Escape), name the MAP sensor in their defect text and print no trouble code; their terms are in the P0106 guide.
What 12 complaints show, and what they cannot
What we counted. We went through every complaint in NHTSA's file, received from January 2015 through October 2026, that prints P0107 in any spelling, or P0108, P0109 or P0105 as the MAP circuit code: 12 complaints, 7 printing P0107, 4 printing P0108, 1 printing P0109 (the 2014 Escape's), with the Sonata printing P0105 and P0107. The number is small enough that every complaint is told or listed here; the table is published. They are about 4 GM cars, 3 Hyundai and Kia, 2 Ford, a Honda, a Toyota and a Dodge, model years 1996 to 2019.
Is a stall with P0107 dangerous, and does a new sensor stop it? PulsCar read all 12 complaints that print P0107 or a sister MAP circuit code: 8 describe a stall, 9 a loss of power or a limp mode, and 10 one or the other; 5 say the problem came back after a reset or a repair. None of the 12 NHTSA forms records a crash, and none gives a repair price. A new sensor is on record in two: a 2009 Azera where the code persisted and an Accord whose owner fitted one after the car had stopped moving, and which did not get into gear afterwards. These are owners who wrote to NHTSA, not a rate. The documents say what to check; our rule for a stall is a tow, not a drive to the shop.
Stall or power loss. The 2018 Explorer is the most complete account: "POWERTRAIN MALFUNCTION (WRENCH) LAMP, SERVICE ADVANCETRAC MESSAGE, HILL START ASSIST NOT AVAILABLE MESSAGE, AND LACK OF POWER WITH DIAGNOSTIC TROUBLE CODE P0107 (MAP FAULTY)" while "PULLING AWAY FROM A RED LIGHT", with power steering lost and the car pushed to safety. A 2013 Traverse owner lists P0107 with an engine that "cuts off while driving"; a 2019 Highlander owner printed "P0191, P0171, P0174, and P0107B" with stalls; a 2018 Durango owner wrote of a vehicle "not responding to gas pedal while driving on highway".
What the complaints cannot tell you. Which code caused which symptom: most print several codes at once, and in 7 of 12 no cause is stated.
Can you drive with P0107?
It depends on how the car behaves. If the car has stalled, lost power, shown a reduced-power or stop message, or failed to restart even once, or if the check engine light is flashing, do not drive on: pull over safely, switch the engine off and have the car towed. That is our advice, not a maker's. The only exception, a flashing light alone on a car that starts and runs normally, is a shop within 2-3 miles, reached gently, at 31 mph (50 km/h) or less with light throttle.
No maker paper we read about P0107 says to stop driving. The nearest statements are these. 🟢 Chevrolet's 2025 Silverado manual says of a flashing lamp: "reduce vehicle speed and avoid hard accelerations and uphill grades" and "If the light continues to flash, find a safe place to park. Turn the vehicle off and wait at least 10 seconds before restarting the engine" (it then tells the owner to see a dealer as soon as possible if the light is still flashing); of its reduced-acceleration message it says: "The vehicle may be driven while this message is on, but maximum acceleration and speed may be reduced. Anytime this message stays on, or displays repeatedly, the vehicle should be taken to your dealer for service as soon as possible", and adds "Under certain operating conditions, propulsion will be disabled." 🟢 Ram's 2026 manual says "Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system" and "If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required." 🟢 Mercedes' tech topic says the engine "may experience torque reduction when fault occurs"; GM's truck program says a harness fault may lead to "reduced engine power, no start condition or in rare cases a stall". GM's statement is softer than ours; ours is the stricter rule, and it is ours.
Why not drive a stalling car anywhere to see if it clears: the 2018 Explorer owner wrote that power steering was lost, and the 2013 Traverse owner wrote of near misses. A steady light and a car that drives normally can wait for a diagnosis within days rather than weeks (our advice, and looser than the 1999 Toyota manual, an unofficial copy, which says to have the car checked "as soon as possible").
Should you buy a used car with P0107 in its history?
Ask what was found, not what was replaced; a repaired connector or harness followed by a clean drive beats the same code coming back. Ask a dealer, by VIN, whether the car is in a harness program or a bulletin from the atlas above (GM's N192219370 ended in 2021, but the harness damage it described may still be there, our reading). Before you pay, have the car scanned, driven to full warm-up and scanned again, with the MAP reading on screen.
Clearing P0107 before an inspection
A cleared code returns if the cause is a half-seated plug or a chafed wire, and an inspection or emissions test needs the car's self-checks to have run again (our advice). Fix first, drive several normal trips, then test. Chrysler's Jeep page says three good trips turn the lamp off ("Three good trips to turn off the MIL"), which is its own rule for its own vehicle. Our guide on how to reset a check engine light covers the mechanics.
Three P0107 traps
Trap 1 · Buying the sensor from the code. The code says the signal is low; it does not say whether the sensor, its wire, its ground or the supply is to blame. Chrysler's page reaches the sensor only through a measurement, Saab's page says to do the circuit tests first, and an Azera owner whose shop replaced the sensor wrote that the same P0108 code was still there when the car sat in the driveway.
Trap 2 · Clearing the code and driving on after a stall. A cleared code returns if the cause is a wire or a plug. A 2007 Aura owner wrote that the codes kept returning after being cleared, that a dealer reset them and updated the engine computer, and that the car stalled the next night; the complaint does not tie the cause to a wire or plug. A stall is a tow (our advice), not a reason to clear and see.
Trap 3 · Using another maker's number as yours. The thresholds on this page are printed on one page each (a Jeep page with no model, 0.08 volt; a 2011 Saab 9-5, 0.19 volt; an Astra J 1.4L Vauxhall, 3.5 kPa), and unofficial copies of Toyota's 1999 Camry manual and Nissan's 2000 Frontier manual print the same circuit as P0105. The paper for your car decides.
Three P0107 scenarios, decoded
These are composite scenarios, not individual customers; every fact in them is printed in a document or a complaint cited above.
A 2018 Ford Explorer with the 3.5L EcoBoost lights its wrench lamp and a Service AdvanceTrac message, loses power at a red light and sets P0107. Under our rule it is towed. At the dealer, the customer asks whether Ford's TSB 19-2212 applies to the VIN and whether the 0.3 hour of printed labor is on the quote.
A 2019 Chevrolet Silverado 1500 with the 2.7L engine sets a long list of codes including P0107. The customer asks the dealer for the harness inspection in PIT5677E and whether program N192219370 ever ran on the VIN (it ended on December 31, 2021).
A 2010 Chevrolet Cobalt shows reduced engine power, P0107, P0452, P0532 and P0641. Several sensors reading low and a reference-voltage fault: the customer asks the shop to measure the 5-volt supply and the sensor ground and to check the engine computer's connector terminals before any sensor is ordered.
The P0107 plan: 10 minutes, today, this week
First, the rule. If the car has stalled, lost power, shown a reduced-power or stop message, or failed to restart even once, or if the check engine light is flashing, do not drive on: pull over safely, switch the engine off and have the car towed. That is our advice, not a maker's. The only exception, a flashing light alone on a car that starts and runs normally, is a shop within 2-3 miles, reached gently, at 31 mph (50 km/h) or less with light throttle. Then, today (10 minutes). Key off, check that the plug clicks and is dry, look at the hoses, read the whole code list (a parts store or a shop may read it if you own no reader; ask first) and write down the mileage and what happened that day. Today (VIN). Enter your VIN at nhtsa.gov/recalls for open recalls, then ask a dealer whether there is a bulletin, harness program or software update for P0107 on your VIN; if your car is in the atlas above, give them that paper's number. This week. If the light is back and the car drives normally, pay for one diagnosis, ask for the live reading in writing and for the cheapest route to be tried first.
Sources and documents
Primary documents only. Where a claim in this guide is marked 🟢, it rests on one of the items below, and the reference is given so you can pull the document yourself. Claims marked ⚪ are shop-price estimates carried from PulsCar's repair guides, not measurements. Pages named without a link are unofficial copies of makers' manuals hosted outside the makers' sites (Saab on saabwisonline.com, Jeep in an Amazon S3 file bucket, the others on library or private servers whose addresses we do not publish).
- General Motors: PIP4409E and PIP4409F; PIP5344; PIT5677, PIT5677A, PIT5677B, PIT5677C and PIT5677E; PIT5713 and PIT5713A (two other filings of the same revision: 10176304, 10187200); Customer Satisfaction Program N192219370; informational 20-NA-104. Owner's manuals: 2025 Chevrolet Silverado 1500.
- Saab and Vauxhall (workshop pages): Saab 9-5 (9650) 2011, 2.0 l petrol, and Saab 9-2X (9346) 2005, 2.0T, on saabwisonline.com (not linked); Vauxhall Astra J 1.4L (LDD, LDU, LLU, LUH, LUJ), DTC P0107 or P0108.
- Ford: TSB 19-2183 and TSB 19-2212 (the same bulletin also filed as 10163568).
- Stellantis (Chrysler, Jeep, Ram): Jeep service page "P0107-MANIFOLD ABSOLUTE PRESSURE SENSOR CIRCUIT LOW" (an unofficial copy in an Amazon S3 file bucket outside Chrysler's site, not linked; the page prints no model); Ram STAR case S1808000282; 2026 Ram 1500 owner's manual.
- Subaru and Porsche: Subaru 07-96-15; Porsche 23/14 ENU 2480.
- Mercedes-Benz: LI15.18-P-071185.
- Honda, Volkswagen, Nissan, Toyota, Mitsubishi: Honda Jazz service page "DTC Troubleshooting: P0107 (3-1)" (L15A, 5-speed manual); Volkswagen Polo Mk3, self-diagnosis fault table, SAE P0 codes; Nissan 2002 Maxima engine-control manual, "DTC P0107, P0108 ABSOLUTE PRESSURE SENSOR" (EC-200 to EC-202), the Maxima absolute pressure sensor description page and the 2000 Frontier engine-control manual, "DTC P0105 ABSOLUTE PRESSURE SENSOR"; Toyota 1999 Camry repair manual, diagnostics section, "DTC P0105 Manifold Absolute Pressure/Barometric Pressure Circuit Malfunction", and its owner's manual (malfunction indicator lamp); Mitsubishi Montero 2002-2004 workshop manual, "DTC P0107: Barometric Pressure Circuit Low Input".
- Hyundai: 2023 Elantra owner's manual, malfunction indicator lamp.
- Carista: P0107 code page, symptom list only.
- PulsCar analysis of NHTSA public data, November 2026: the 12 complaints, the table, the document list, the sorting rules and how we did it (CC BY 4.0).
For the neighbouring pages: the P0106 guide for the range and performance code, the P0101 guide and the P0103 guide for the mass air flow codes, P0299 for underboost, P0171 for the lean code, throttle body replacement cost, a car that hesitates when accelerating, a car that stalls while driving, a flashing check engine light with a shaking car, how to reset a check engine light, what a check engine light means, how much a car diagnostic costs, how to find an honest mechanic and the check-engine code index.
PulsCar does not diagnose a MAP circuit fault from the sound of the engine. For P0107, the readings at the sensor and the documents above are the evidence.
Prices verified November 2026 in the repair guides they are carried from, and reviewed quarterly. Technical documents verified November 2026: GM PIP4409F, PIP5344, PIT5677E, PIT5713A and N192219370, Ford TSB 19-2212, Subaru 07-96-15, Porsche 2480 ENU 23/14, Ram S1808000282 and Mercedes-Benz LI15.18-P-071185 were read in the NHTSA files; the Saab, Vauxhall, Jeep, Honda, Volkswagen, Nissan, Toyota and Mitsubishi page copies and the Chevrolet, Ram and Hyundai manuals were read on 20 November 2026.
Had a P0107 fixed by a plug, a wire, a ground, a sensor or a computer, or by none of them? Email [email protected] with the vehicle, mileage and what finally worked.

