💡 The answer in 60 seconds

Measure all four tires and the spare cold, with your own gauge, and compare each reading with the pressure on your car's label, not with the number on the tire. The label (the placard) is usually on the driver's door pillar, the frame edge you see with the door open, or the figures are in the owner's manual; front, rear and spare can differ. Never inflate a tire above the maximum pressure molded on its sidewall. The number to inflate to is on the vehicle's placard or in the owner's manual, not on the tire. Cold means parked about three hours or driven less than a mile, which most of the sources we read print; measuring before the first drive of the day, after the car sat overnight, fits every definition. Remove the valve cap, press the gauge on until the hissing stops, read it, add air or release a little with the pin in the valve, measure again, and put the cap back. Do not let air out of a tire that is warm from driving: the higher reading is normal, and the tire will be underinflated once it cools. Check again when it is cold. If the light is already on, check all four tires with the gauge and fill them to the label; if it stays on after that, our tire pressure light guide covers the rest. If the low tire pressure light comes on while you are driving, or a tire looks flat, slow down smoothly, avoid hard braking and sudden steering, pull off to a safe place and stop as soon as possible to check the tires. Most makers ask for a check at least monthly (Toyota: every two weeks, or at least once a month), and a warning light does not replace it.

This page answers one question: how do you check the air pressure in your tires, and what number do you check it against. It is not about why the dashboard light is on (our tire pressure light guide covers causes, sensors and repairs), how to decode the numbers on a tire's sidewall (see how to read tire size), when a tire is worn out (see when to replace tires) or which tire to buy. PulsCar publishes this guide; it sells no tire gauges or tires, and no link on this page is an affiliate link. We did not test any gauge or any pressure setting. Everything below is what vehicle makers, tire makers, the tire industry's trade body, a gauge maker, a tire-service retailer, one magazine, a federal fuel-economy site and two federal rules print, each named and read on 11 November 2026. 🟢 Official marks a federal text; maker and retailer pages are named in words. Where sources disagree, we show both and do not average them.

The five steps at a glance

Step 1. Find your car's number. On the label on the driver's door pillar, or in the owner's manual; front and rear can differ, and the spare has its own figure. Never the sidewall number
label or manual, not the tire
Step 2. Make sure the tires are cold. Parked about three hours or driven less than a mile (most makers); before the first drive of the day is the simple rule
before you drive
Step 3. Use your own gauge. Stick, dial or digital; Michelin and Bridgestone warn the gauge on a gas-station air hose may be unreliable
own gauge
Step 4. Measure every tire, then the spare. Cap off, gauge on straight until the hiss stops, read, write it down
all four + spare
Step 5. Adjust, measure again, cap on. Add air, or release a little with the valve pin, and never from a warm tire
recheck, cap on

Step 1: find the number your car needs

The right pressure is not a property of the tire. It is the vehicle maker's figure for a given car with a given tire size, and it is printed in two places. The first is a label on the car. The federal standard for vehicle placards, 49 CFR 571.110 🟢, requires each car to carry a placard showing the "Vehicle manufacturer's recommended cold tire inflation pressure for front, rear and spare tires", permanently affixed to the driver's side B-pillar, the pillar behind the front door. If the car has no driver's side B-pillar and two doors opening in opposite directions, the placard goes on the forward edge of the rear side door; if neither spot can hold a legible placard, on the rear edge of the driver's door, then on a surface next to the driver's seat. A maker may instead show the pressure on a separate tire inflation pressure label next to the placard. The second place is the owner's manual, which has a specification chart.

The manuals and tire makers we read describe the same spots, in their own words. Nissan's manual says the Tire and Loading Information label "is affixed to the driver side center pillar." Hyundai and Kia say the specifications "can be found on a label attached to the driver's side center pillar." Subaru says the label "is located on the door pillar on the driver's side." The Volkswagen Tiguan manual we read, the Indian edition, says the sticker is on the driver door pillar or inside the tank flap. Michelin's US page says the sticker is "on the driver's door pillar or on the back of the fuel filler flap", and Continental says some vehicles also show it on the fuel filler door. The US Department of Energy's fuel economy site names the "driver's side door jamb or the glove box and in your owner's manual."

Three things can surprise you when you read the label.

Front and rear can differ. The tire industry's trade body, USTMA, notes that some vehicles have different cold inflation pressures for tires on the front and rear axles, and Bridgestone tells drivers to write down the number for each tire so they do not mix them up as they walk around the car.

The figure depends on the tire size. The 2023 Nissan Altima manual we read lists 220 kPa (32 psi) for the 215/60R16 size and 230 kPa (33 psi) for the 215/55R17 and 235/40R19 sizes, all listed for the same model, and 420 kPa (60 psi) for either of two compact spare sizes. If you have fitted a different size, the federal wording that appears in the Chevrolet and Mazda manuals applies: "If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires." Goodyear's own service bulletin to its dealers says that when tires other than the approved original sizes are applied, load and inflation tables are needed to determine the proper pressure. That is a job for a tire shop, not a guess.

The label may describe a full load. Chevrolet's manual says that the recommended pressure "is the minimum air pressure needed to support the vehicle's maximum load carrying capacity." Goodyear's bulletin warns that some manufacturers of vans and light trucks may list only the pressure for the maximum vehicle load when fitted with Load Range D or E tires, which may leave them over-inflated when lightly loaded. Volkswagen's Tiguan manual says that, depending on the vehicle, the sticker may also show a comfort tire pressure for more driving comfort and that fuel consumption may increase with it, and that the pressure should always be adjusted to the load level.

The number on the tire's sidewall is a ceiling, not the target

Every tire has a pressure figure molded into the sidewall, and drivers inflate to it by mistake. Goodyear, Bridgestone, Michelin, Continental and the trade body say the same thing, in similar words. Goodyear's dealer bulletin says the pressure on the sidewall "is the MAXIMUM operating pressure for the tire. It is not necessarily the correct inflation pressure for the vehicle." USTMA says the sidewall pressure is "the maximum allowed in the tire, irrespective of the vehicle," and tells drivers to follow the vehicle maker's recommendations. Michelin's Canadian page says to use the pressure from the door placard or the owner's manual, "not the maximum on the tire sidewall," and its US page says the recommended pressure is not on the sidewalls. Continental calls the sidewall figure the tire's upper structural limit. The US Department of Energy puts it plainly: "Do not use the maximum pressure printed on the tire's sidewall."

The vehicle makers add the other half of the rule. Toyota's specification table for the Camry Hybrid says that for driving at high speeds above 100 mph (in countries where such speeds are permitted by law) a driver should add 5 psi to the front and rear tires, and then adds: "Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall." USTMA says the same in its own words: "Do not exceed the maximum inflation pressure shown on the tire sidewall." Never inflate a tire above the maximum pressure molded on its sidewall. The number to inflate to is on the vehicle's placard or in the owner's manual, not on the tire.

For what the other sidewall numbers mean (size, load index, speed rating, date code), see how to read tire size.

Step 2: make sure the tires are cold, and what "cold" means

A car's recommended pressure is a cold pressure. Driving warms the air in the tire and raises the reading, so a measurement taken after a drive is not comparable with the label. The makers we read agree on the principle and differ on the details, which is why this table prints each maker's own definition.

Chevrolet (2023 Equinox). "Check the tire inflation pressure when the tires are cold, meaning the vehicle has not been driven for at least three hours or no more than 1.6 km (1 mi)."
3 hours, or up to 1 mile
Toyota (Camry Hybrid). "If your vehicle has been parked for at least 3 hours or has not been driven for more than 1 mile or 1.5 km, you will get an accurate cold tire inflation pressure reading."
3 hours, or up to 1 mile
Nissan (2023 Altima). "Tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds."
3 hours, or under 1 mile
Hyundai (2023 Elantra). "A cold tire means the vehicle has been sitting for 3 hours and driven for less than 1 mile (1.6 km) in that 3 hour period." Another page of the same manual says "has not been driven for at least three hours or has been driven for less than one mile (1.6 km)."
'and' on two pages, 'or' on one
Kia (2024 Sportage). "'Cold' means your vehicle has been sitting or at least three hours or driven no more than 1 mile (1.6 km)."
3 hours, or up to 1 mile
Mazda (2023 MX-5). "Make sure the tires are cold ―meaning they are not hot from driving even a mile."
not hot, even from a mile
Subaru (US manual). The tires are cold when the vehicle has been "parked for at least 3 hours or has been driven less than 1 mile (1.6 km)."
3 hours, or under 1 mile
Volkswagen (Tiguan, India edition). "The specified tyre pressure applies to cold tyres." Its tyre-loss-indicator page says the vehicle must have been "stationary for 3 hours or driven only a few kilometres at a slow speed during this time"
3 hours, or a few km slowly

Tire makers and the trade body, read on the same day:

USTMA (Tire Care and Safety Guide). "Check inflation pressure when tires are cold, that is, when the vehicle has been parked for at least 3 hours or has been driven less than one mile at moderate speed."
3 hours, or under 1 mile
Goodyear (dealer bulletin PSB 2015-25). "Always check inflation when tires are COLD: when the vehicle has been driven less than one mile (1.6 km) or at least three hours after driving."
under 1 mile, or 3 hours
Bridgestone (US page). "Tires are considered cold when the vehicle has been parked for three hours or more, or if the vehicle has been driven less than a mile (1.6 km) at moderate speed."
3 hours, or under 1 mile
Continental (US page). "Cold means the vehicle has been stationary for at least three hours, or driven under a mile at moderate speed."
3 hours, or under 1 mile
Michelin (tire-pressure pages, US and Canada). "Check your tires “cold”—before you’ve driven or at least three hours after you’ve driven."
before driving, or 3 hours after
Michelin (how-to-inflate pages, US and Canada). "Check the pressure preferably when the tires are cold (your car should not have been used in the last 2 hours or should have travelled less than 2 miles at low speed)."
2 hours, or under 2 miles
Cooper Tire Canada (page title reads Goodyear). "Proper tire inflation should be checked when the tires haven’t been driven on for several hours and have had time to cool down."
several hours

Read this table for what it says and what it does not. Most of the sources print the same pair of tests, about three hours parked or under one mile driven, and joined by "or". Hyundai's manual joins them with "and" on two pages (the one-mile test within the three-hour period, which is stricter) and with "or" on a third (Volkswagen's "during this time" may be read the same way as Hyundai's "and"; that reading is ours). Mazda sets no count of hours and says a drive of even a mile makes a tire not cold. Michelin's own pages differ: its how-to-inflate pages say two hours or two miles (their FAQ paragraphs add 2 to 3 hours on the US page, and parked 3 or more hours or driven fewer than 5 km on the Canadian one), while its tire-pressure pages say before driving or three hours after. We found no source that explains why the figures differ, and we do not average them. The simple rule that fits every row is to measure before the first drive of the day, with the car parked overnight, where that is possible: it is cold under every definition above. If you must check at a gas station after a drive, read the section on warm tires below.

Temperature and altitude also change the reading, and they are not part of any definition of cold. USTMA says significant changes in altitude or temperature change the pressure and "will require an adjustment." The temperature section below gives the printed rules of thumb.

Step 3: use your own gauge, because the eye cannot do this job

Many of the sources we read (the Chevrolet, Toyota, Hyundai, Kia and Mazda manuals, USTMA) say a tire's pressure cannot be judged by looking at it. Toyota's manual says: "It is difficult to judge if a tire is properly inflated based only on its appearance." Chevrolet says: "Proper tire inflation cannot be determined by looking at the tire." Mazda warns that "A tire can lose up to half of its air pressure and not appear to be flat!" USTMA says drivers must use a tire gauge, and adds that "Motorists should have their own gauge and keep it in the vehicle." A gauge seller, JACO, says the same about the naked eye.

The gauge built into a gas-station air hose is the other tempting shortcut. Michelin and Bridgestone warn against relying on it. Continental's page says many newer pump units include a built-in gauge, which simplifies the process, and does not comment on its accuracy. Michelin's Canadian page says: "Gas station pressure gauges are often unreliable; invest in your own calibrated gauge." Its US page says that the inflation gauge at a petrol station "is not always calibrated, hence not always reliable", and suggests having the pressure checked occasionally by a professional or using a calibrated gauge of your own. Bridgestone says it is best to use a personal gauge rather than those attached to air hoses at service stations, because they are "the most likely to be weathered, and possibly inaccurate." Goodyear, in its bulletin to dealers, tells them to "Use a good quality tire gauge and check it regularly for accuracy." The bulletin does not say how a dealer should check a gauge.

Which kind of gauge is where the sources part. Here is what each says about the three common types, side by side.

Mazda (2023 MX-5 manual, TPMS page). "When checking tire pressures, use of a digital tire pressure gauge is recommended."
recommends digital
Michelin (Canada). "A digital gauge gives the most accurate reading, though a quality analogue gauge works fine."
digital most accurate
Continental (US). Analog dial gauges "require no batteries"; digital ones have backlit screens but need battery power; pencil-style stick gauges are "slightly less accurate than the other two"; "Dial and digital models generally deliver more consistent accuracy."
dial and digital over stick
Bridgestone (US). "A digital tire pressure gauge will provide accurate readings, but don’t forget that it operates on a battery." If having to replace the battery would stop you using it, it says to go with a standard gauge
digital needs a battery
Mavis (retailer). "Both types can be accurate when used correctly", and the best gauge is whichever you will use most
both can be accurate
Popular Mechanics (editors' list, not a test). An analog gauge is "much more reliable as it doesn’t need batteries and only has one moving part"; with a digital one it recommends carrying spare batteries
editors' view, no test
USTMA (trade body). "A gauge calibrated in 1 psi increments up to 60 psi is sufficient for most passenger tires." It shows mechanical and digital styles and ranks neither
1 psi steps, up to 60 psi

Continental says dial and digital gauges beat a pencil gauge; Bridgestone, Continental and Popular Mechanics note that a digital gauge needs a working battery; Bridgestone calls pump-hose gauges the most likely to be weathered and possibly inaccurate, and Michelin says they are not always reliable. Mavis says either type can be accurate, and Popular Mechanics' editors call an analog gauge much more reliable for needing no batteries, while Mazda and Michelin Canada lean digital. Chevrolet's manual simply asks for "a good quality pocket-type gauge", and Hyundai and Kia ask for a "good quality" gauge without naming a type.

How do you know your gauge is "good quality"? The manuals do not define it. The nearest things are the trade body's 1 psi steps and a gauge seller's accuracy claims, in the section on what to compare in a gauge, further down.

Which tire pressure gauge should you buy? None is named here. PulsCar publishes this guide and does not sell tire gauges, tires or any pressure tool, and no link on this page is an affiliate link. We did not test any gauge, so we name no best one. What the sources print is a short list of things to compare: a range that covers your car's pressure and the 60 psi that compact spares need, readings in steps of 1 psi, an accuracy figure the maker states, a battery or no battery, and a display you can read in the dark. The tire industry's trade body says a gauge calibrated in 1 psi steps up to 60 psi is sufficient for most passenger tires, Mazda's manual recommends a digital gauge, and Michelin and Bridgestone say not to rely on the gauge built into a gas-station air hose.

Step 4: measure every tire, in this order

The manuals and tire makers we read describe broadly the same sequence. This is the version that combines them, with the source of each step.

  1. Park on level ground with the tires cold (Continental says level ground; the cold definitions are in step 2). Have your target figure for each tire ready: Bridgestone says to write down the figure for each tire if the front and rear differ, so that you do not confuse them as you move around the car.
  2. Take the valve cap off one tire and set it where you will not lose it (Continental). Toyota, Chevrolet, Hyundai, Kia, Mazda and Nissan all list this step.
  3. Press the gauge onto the valve stem firmly and squarely until the hissing stops (Chevrolet: "Press the tire gauge firmly onto the valve to get a pressure measurement"). Nissan adds that you should not press too hard or force the valve stem sideways, or air will escape, and that if you hear the hiss you should reposition the gauge.
  4. Read the number and write it down (Bridgestone). With a stick gauge the bar pops out and shows the figure; with a dial you read the needle; with a digital gauge the screen shows it.
  5. Compare it with the label. Chevrolet, Hyundai and Kia all say that if the cold pressure matches the recommended pressure on the label, no further adjustment is necessary.
  6. Repeat for all four tires and the spare (Mazda: "Repeat with each tire, including the spare."). Do the spare when you do the others: Hyundai and Kia say to check it each time you check the others, Toyota and Chevrolet say not to forget it, USTMA says to check it monthly, and Michelin's how-to-inflate pages are of two minds, as the spare section below shows.
  7. Look while you are there. Mazda's procedure ends with two checks: "Visually inspect the tires to make sure there are no nails or other objects embedded that could poke a hole in the tire and cause an air leak", and "Check the sidewalls to make sure there are no gouges, cuts, bulges, cracks or other irregularities." A bulge, a blister, exposed cord or fabric, or a deep cut or open crack in the sidewall means the tire is finished: do not keep driving on it. Fit the spare, or have the car towed to a tire shop. Hyundai's and Kia's manuals add a bulge in the tread and cord or fabric showing anywhere: replace the tire. Our guide to when to replace tires covers the damage and wear rules in full.

If your car is a Nissan with an Easy-Fill Tire Alert, the manual says the system gives visual and audible signals outside the vehicle while you inflate a tire to the recommended cold pressure, and that "If the Easy-Fill Tire Alert is not working, use a tire pressure gauge." Some cars also show each tire's pressure on a dashboard screen. That display is a convenience, and we return to how far to trust it in the section on warning lights.

Step 5: adjust, measure again and put the cap back

If the tire is low, add air and measure again. Continental says to check the pressure at intervals during inflation rather than filling continuously, and to work in short bursts and recheck between each release if you need to let air out. USTMA says that on a T-type temporary spare you should adjust in small amounts, because the tire is smaller and the pressure level changes rapidly. The gas-station pump is a source of air, not a source of truth about the number: Michelin's US how-to-inflate page says to use your own calibrated gauge to check the tire, use the station's air to inflate, and recheck with your gauge to confirm.

If the tire is high, release a little. The manuals describe the same trick. Chevrolet: "If the inflation pressure is high, press on the metal stem in the center of the tire valve to release air." Hyundai, Kia and Toyota describe the same pin in the center of the valve; Nissan, the valve stem core. Release a little, measure, repeat. This is for a tire that is cold. Do not let air out of a tire that is warm from driving: the higher reading is normal, and the tire will be underinflated once it cools. Check again when it is cold.

Then measure again. Chevrolet says to "Recheck the tire pressure with the tire gauge." Nissan says to recheck and add or release air as needed.

Put the cap back on, and use the right cap. Toyota says to put the valve cap back so dirt or moisture cannot cause an air leak; its procedure has you apply soapy water to the open valve and check for leakage first, then fit the cap. USTMA says always cover the valve stem with a sealing cap. Two maker-specific cautions: Chevrolet says to use only valve caps designed for the vehicle by GM, because tire pressure monitoring (TPMS) sensors could be damaged and would not be covered by the vehicle warranty, and Mazda says to use only a genuine Mazda valve cap, because with a non-genuine part the correct pressure cannot be maintained if the tire valve becomes damaged. If your car has TPMS sensors in the wheels, read the cap line in your own manual.

Never inflate a tire that is not on a car. USTMA warns: "Never inflate a tire unless it is secured to a vehicle, tire mounting machine or other restraining device." This applies to a loose spare or a wheel you are working on, not to the check described above.

The warm-tire problem: what the makers print

You can do all of the above at a gas station after a drive. The tires are then warm, the reading is higher than the cold figure, and the sources fall into two groups (some also give an add-air figure), and none says to let air out. This is the part of the topic where the advice you find online is most mixed, so here are the printed rules we read, one row per source.

Toyota (Camry Hybrid manual). "It is normal for the tire inflation pressure to be higher after driving as heat is generated in the tire. Do not reduce tire inflation pressure after driving."
never reduce after driving
Hyundai (2023 Elantra). "Warm tires normally exceed recommended cold tire pressures by 4 to 6 psi (28 to 41 kPa). Do not release air from warm tires to adjust the pressure or the tires will be under-inflated."
+4 to 6 psi; do not release
Kia (2024 Sportage). The same statement as Hyundai's: warm tires normally exceed the recommended cold pressures by 4 to 6 psi (28 to 41 kPa), and air should not be released
+4 to 6 psi; do not release
Subaru (US manual). "The air pressure in a tire increases by approximately 4.3 psi (30 kPa, 0.3 kgf/cm2) when the tire becomes warm." "Do not let air out of warm tires to adjust pressure."
about +4.3 psi; do not release
Mazda (2023 MX-5). "Warm tires normally exceed recommended pressures. Do not release air from warm tires to adjust the pressure."
do not release
Volkswagen (Tiguan, India edition). "Tyre pressure is always higher in warm tyres than it is in cold tyres. For this reason, never reduce the pressure in warm tyres to adjust the tyre pressure."
never reduce
USTMA (trade body). "Never “bleed” or reduce inflation pressure when tires are hot from driving, as it is normal for pressures to increase above recommended cold pressures."
never bleed a hot tire
Goodyear (dealer bulletin). "If you must check inflation when tires are hot, add 4 psi (27.8 kPa) to the recommended cold inflation pressure."
add 4 psi when hot
Bridgestone (US page). "If it is necessary to adjust inflation pressure when tires are “hot”, set their pressure to 4 psi (14 kPa) above the recommended cold inflation pressure. Recheck the inflation pressure when the tires are cold."
set 4 psi above; recheck cold
Michelin (how-to-inflate pages, US and Canada). "If, however, the pressure is checked while the tires are warm, add 0.3 bar (4.35 PSI) to the pressure recommended by the vehicle manufacturer. The pressure should then be checked and readjusted when the tires are cold." The next line of the same paragraph: "Never deflate a warm tire (pressure increases with temperature)."
add 0.3 bar; recheck; never deflate
Michelin (tire-pressure page, Canada). "Never deflate a hot tire: the higher reading is normal and will correct when the tire cools."
never deflate a hot tire

Three things follow, and none is our opinion. First, no source we read says, for a warm tire, to let air out to reach the cold number. Second, the vehicle makers who print a figure (Hyundai, Kia, Subaru) say how much warm tires typically exceed the cold pressure, not to add that much, and they differ (4 to 6 psi, and about 4.3 psi). Third, only Goodyear, Bridgestone and Michelin's how-to-inflate pages give a warm-tire figure (add 4 psi, set 4 psi above, add 0.3 bar), about 4 to 5 psi (Michelin's 0.3 bar is 4.35 psi, and its Canadian FAQ says 4 to 5 psi); Bridgestone and Michelin say to measure again when the tire is cold, the step a quick stop at the pump leaves out.

Michelin's US how-to-inflate page guards against the opposite mistake: do not use a warm reading as the baseline, because a tire inflated to the recommended level while warm will be underinflated once it cools; and if the pressure is lower than the recommendation even when warm, add air. USTMA says the same from the other side: "If a hot tire pressure reading is at or below recommended cold inflation pressure, it may be dangerously under inflated." In that case, the trade body says to determine the cause immediately and/or have the tire checked by a tire service professional.

So the simplest honest version is: if you can wait or drive home, check cold; if you cannot, treat the warm reading as a screening, never let air out, and measure again when cold. If a warm tire reads at or below the cold figure, USTMA says it may be dangerously under inflated: find the cause immediately and/or have a tire professional check it; Michelin's US how-to-inflate page says to add air in that case, and the figures of Goodyear, Bridgestone and Michelin put a warm tire about 4 to 5 psi above the label; USTMA: never above the sidewall maximum. Do not let air out of a tire that is warm from driving: the higher reading is normal, and the tire will be underinflated once it cools. Check again when it is cold.

How often to check, and why the number changes

The manuals and makers mostly ask for a check at least monthly (Nissan says "often"). They do not word it identically, and Kia's own manual says it two ways.

Toyota (Camry Hybrid). "You should check tire inflation pressure every two weeks, or at least once a month."
every two weeks, or monthly
Kia (2024 Sportage). A warning says to check "at least twice a month and before any long trips on the road"; the procedure page says "Check your tires once a month or more."
twice a month, or once or more
Nissan. Check "often and always prior to long distance trips"
often, and before trips
49 CFR 571.138 🟢. The wording the owner's manual must carry: tires "should be checked monthly when cold"
monthly, cold
USTMA. At least once a month with an accurate gauge, and additionally before long trips, carrying heavy loads, towing a trailer and any time high speeds are anticipated
monthly, plus before heavy use

Why so often? Because a tire loses air without any fault, and because the temperature moves the number. The makers give a range for each, and again they differ. Here are the losses per month first.

Michelin (tire-pressure pages). Tires have been known to "lose up to 1psi" every month
up to 1 psi a month
Michelin (how-to-inflate pages). A tire loses air "usually around 1.45 psi per month (.1bar)"
about 1.45 psi a month
Bridgestone (Americas). Tires lose "approximately 1 pound per square inch (PSI)" of pressure every month
about 1 psi a month
Continental (US). Tires "lose 1 to 2 PSI each month through natural air seepage" (the same page also says up to 1 psi)
1 to 2 psi a month
USTMA. Tires "may lose 1 to 2 psi inflation pressure per month under normal conditions"
1 to 2 psi a month
Goodyear (dealer bulletin). Tires "can lose up to 2 or more psi (13.8 kPa) per month"
up to 2 or more psi a month

USTMA adds the limit that turns a normal loss into a warning: if a tire continually loses more than 2 psi per month, have it checked by a tire service professional. USTMA also says: "Any tire that continually requires re-inflation is a serious safety risk."

And the change with temperature, from the same kinds of sources:

Goodyear (dealer bulletin). Pressure goes up or down "1-2 pounds for every 10 degrees Fahrenheit (5.5 degrees Celsius)"
1 to 2 psi per 10 F
USTMA. "1 to 2 psi for every 10 degrees F temperature drop"
1 to 2 psi per 10 F
Michelin (how-to-inflate pages). Ambient air temperature "can lose 1-2psi per 10 degrees F"
1 to 2 psi per 10 F
Continental (US). Pressure "shifts approximately 1 PSI for every 10°F change in ambient temperature"
about 1 psi per 10 F
Nokian Tyres. "tire pressure decreases as much as 1 PSI with each 10-degree drop in temperature"
up to 1 psi per 10 F

The range is 1 to 2 psi per 10 degrees Fahrenheit in the Goodyear, USTMA and Michelin rows, and about or up to 1 psi in the Continental and Nokian rows (Bridgestone's Americas page prints about 1 psi and Cooper's Canadian page 1 to 2 psi). We do not average them. What matters for your check is the direction: the first cold morning of the season will read lower than the last warm week did (Cooper's page says a light that comes on in cold weather happens naturally and does not necessarily mean a leak), and USTMA says that significant changes in altitude or temperature "will require an adjustment."

Nokian's page gives an example: if the pressure is set in a 68 F (20 C) garage and the outside temperature is 15 F (-9 C), it says the pressure added should be at least 3 psi higher than the recommended value. The arithmetic of the rules of thumb above is larger (53 degrees at 1 to 2 psi per 10 degrees is about 5 to 11 psi, our arithmetic), so measure at the temperature the car will be driven at. For winter tires, Nokian says to "consider" inflating 3 psi above the all-season recommendation; the vehicle manuals we read do not print that, USTMA's rule is never below the vehicle maker's recommendation and never above the sidewall maximum, and Nokian's own page ends by saying it is the driver's responsibility to follow the vehicle manufacturer's guidelines and to consult a Nokian dealer or the vehicle's manufacturer for specific advice.

What to compare when you buy a gauge

Which gauge is best? An honest answer from us has to start with what we cannot offer. We did not test any gauge. We found no independent laboratory comparison of tire gauges that we could read: the Wirecutter, Consumer Reports and Car and Driver pages we tried were blocked or not found, and we did not get around that. The only magazine list we could read, from Popular Mechanics, is an editors' selection that says it may earn a commission, not a measurement of accuracy, so we cite it only for the criteria its editors name, and we name none of its picks. What follows is the list of properties the sources print, each with who printed it. A buyer can check the label or product page against it.

Pressure range. USTMA says a gauge calibrated in 1 psi increments up to 60 psi is sufficient for most passenger tires, and a dual-head gauge calibrated in 2 psi increments up to 100 psi for light truck tires. Chevrolet, Toyota and Nissan all print 60 psi (420 kPa) for their compact spare tires, and USTMA says T-type temporary spares require 60 psi. A gauge that stops at 50 psi cannot read a compact spare; that is our arithmetic, not a maker's statement. JACO's FAQ adds that you should work out your target pressure first and then choose the range using its margins; in its description of grade B the middle third is the most accurate.

Stated accuracy, and who states it. The most detailed accuracy statement we could read is from JACO, a gauge seller, in its own FAQ. It says its mechanical gauges are calibrated to ANSI grade B40.1 (a standard accuracy grade for mechanical gauges), and explains that the dial is read in thirds: the first third of the scale is accurate to 3 percent, the second to 2 percent and the last to 3 percent. For a 60 psi gauge it lists margins of 1.8 psi (0 to 20 psi), 1.2 psi (21 to 40 psi) and 1.8 psi (41 to 60 psi); for a 100 psi gauge, 3, 2 and 3 psi. It says its digital gauges are factory calibrated to plus or minus 1 percent of full scale (the top of the dial), except one 200 psi model at 0.50 percent. Those figures are a company's claims about its own products, so we mark them as such, and we did not verify them. In arithmetic: a car at 35 psi sits in the middle third of a 60 psi dial, where JACO's margin is 1.2 psi, about 3.4 percent of 35 psi; on a 100 psi dial the same 35 psi falls in a third with a margin of 2 psi, about 5.7 percent. JACO's text says the percentages apply to true pressure, but its psi figures equal percentages of the full scale (3 percent of 60 is 1.8), and we print its figures.

What a margin means in practice. The federal rule for warning lights is built around a quarter of the pressure (more on this below), so a 1.2 psi margin on a 35 psi tire does not hide a flat. It can matter for finer questions, such as whether your fronts are 35 or 36, or whether one tire is 2 psi lower than its partner, and it shows why two gauges can disagree by a psi or two on the same tire without either being broken. Goodyear's advice to check a gauge regularly for accuracy has one practical form that needs no lab: measure the same tire with a second gauge, and treat a gap wider than the stated margins as a reason to have a tire shop check which one is off. That method is our suggestion, not a maker's.

Power and seal. A digital gauge needs a battery (Bridgestone, Continental, Popular Mechanics). Every gauge needs to seat on the valve without leaking: Nissan's manual says to press the gauge squarely onto the valve stem, not too hard and not sideways, and to reposition it if air hisses out; Volkswagen's manual says not to position the gauge at an angle to the valve stem, which can damage the tire valve. Popular Mechanics' editors praise one model's twist-on chuck for removing the guesswork of connecting to the valve stem; that is a comment on one product, not a standard.

A release pin or bleed button. Michelin Canada's instructions mention the gauge's release pin for letting out a little air, and Popular Mechanics lists the ability to take air out as a feature; without it, use the valve pin (step 5).

Price. Continental's page says quality gauges, dial or digital, cost between $10 and $20. Popular Mechanics' editors say a daily driver should not spend more than $25. Both are statements from pages we read on 11 November 2026; neither is a price check of any shop.

Who is selling. Several pages above come from companies that sell tires, a gauge or tire service, so weigh the accuracy figures as a seller's claims and the manual wording as the vehicle maker's instruction.

The spare has its own number, and the sources differ on how often to check it

The placard lists a pressure for the spare as well as for the road tires (49 CFR 571.110 🟢 requires front, rear and spare entries on it; a full-size spare's entry may say "see above"), and for a compact temporary spare the number is much higher. Chevrolet's manual says: "The compact spare cold tire pressure should be at 420 kPa (60 psi)." Toyota's and Nissan's specification tables print 60 psi (420 kPa) for their compact spares, and USTMA says T-type temporary spares require 60 psi. Mazda's procedure adds: "Some spare tires require higher inflation pressure." Read the label, not your memory.

On how often, the sources split. Hyundai and Kia say to check the spare every time you check the other tires, Chevrolet and Toyota say not to forget it, and USTMA says full-size and temporary spares should be checked monthly and before any long trips. Michelin's pages print both: monthly for all tires including the spare, and, in the how-to-inflate pages' spare paragraph, that the spare is not used every day, so "you can do it only once or twice a year." We do not choose between them, but one fact bears on it: Chevrolet says its TPMS sensors are on the tire and wheel assemblies "excluding the spare", and Nissan says its system monitors all tires except the spare, so on those cars no light will tell you the spare has gone flat.

Loaded, towing and fast: when the number on the label is not the whole story

USTMA asks for additional checks before long trips, carrying heavy loads, towing a trailer and any time high speeds are anticipated, and Goodyear's bulletin lists the same occasions. Nissan's manual says: "Before taking a long trip, or whenever you heavily load your vehicle, use a tire pressure gauge to ensure that the tire pressures are at the specified level." Toyota's table adds 5 psi to the front and rear tires for driving at high speeds above 100 mph (in countries where such speeds are permitted by law), and says never to exceed the sidewall maximum. Nissan says the cold pressure must be increased above 100 mph where it is legal (on a race track, for example) and to set it back to the normal figure when the speed or load is reduced. The Volkswagen manual we read says to adjust the pressure to the load level on the sticker. Never inflate a tire above the maximum pressure molded on its sidewall. The number to inflate to is on the vehicle's placard or in the owner's manual, not on the tire.

A warning light is not a gauge

Light vehicles built on or after 1 September 2007 (later for multi-stage and altered vehicles) must have a tire pressure monitoring system under the federal rule, 49 CFR 571.138 🟢 (passenger cars, multipurpose passenger vehicles, trucks and buses of 10,000 pounds gross weight or less, without dual wheels on an axle), and it is tempting to treat the system as the check. The rule sets what the light promises: it must come on within 20 minutes after one or more tires are at or below the pressure 25 percent below the maker's recommended cold pressure, or a minimum activation pressure in a table (140 kPa, 20 psi, for standard-load P-metric tires), whichever is higher. For a car whose label says 35 psi, 25 percent below is 26.25 psi, and for 32 psi it is 24 psi (our arithmetic). A tire can be as much as 25 percent under the number on the label before the light is required to come on.

The rule also requires the owner's manual to say so. The text, which appears in the Chevrolet and Mazda manuals we read, includes this sentence: "Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale." Volkswagen's manual says: "Do not rely only on the tyre monitoring system." Mazda's says the system "does not alleviate your need to check the pressure and condition of all four tires regularly." USTMA lists three limits that some such systems may have: no warning until a tire is as much as 25 percent below the recommendation, a possible inability to warn if all tires lose pressure at the same rate when the system compares tires, and a possible failure to warn of rapid loss in a single tire. It still asks for a monthly gauge check.

Some cars show each tire's pressure on a screen. That helps you see which tire is low, but it is not a substitute for the gauge reading. Chevrolet's manual says its driver information display shows the "approximate pressures of all four tires", and Toyota's says the displayed values "may also be different from the values measured using a tire pressure gauge", with the pressure changing with temperature. Some systems need a reset or a drive before the light goes out in certain cases; Toyota's manual, for one, describes an initialization procedure for changes such as tire size, load or rotation, and says it can take a few minutes for the display to show the pressure after it has been adjusted. The causes of a light that stays on, flashes, or returns after you have checked every tire are in our tire pressure light guide.

If the low tire pressure light comes on while you are driving, or a tire looks flat, slow down smoothly, avoid hard braking and sudden steering, pull off to a safe place and stop as soon as possible to check the tires. That wording is built from Nissan's manual, which says to avoid sudden steering maneuvers or abrupt braking, reduce speed, pull off the road to a safe location and stop as soon as possible, and warns that driving with underinflated tires may permanently damage the tires and increase the likelihood of tire failure. For a flat tire the same manual says to replace it with the spare as soon as possible, and the federal wording above says driving on a significantly under-inflated tire causes it to overheat and can lead to tire failure.

Should a warning light replace your gauge, and can PulsCar's free sound check tell you your tires are low? No to both. PulsCar's free sound check is a 30-second engine sound check; it does not measure tire pressure, and nothing on this page is a PulsCar feature. The federal rule behind your car's tire pressure light sets its trigger at a tire 25 percent below the maker's cold figure, so the light is a late warning, not a measurement. Chevrolet's and Mazda's manuals both say the system is not a substitute for proper tire maintenance, and USTMA asks for a monthly gauge check even on cars that have one. So the answer to what checks your tires is a gauge in your hand, a label on your door pillar, and a calendar reminder, with the dashboard light as the backup.

A tire that keeps needing air is a different problem

If one tire is repeatedly lower than the others, the checking is over and the diagnosis starts. USTMA's causes (a puncture, road hazard damage, a leaking valve, a damaged rim or tire mounting damage) are for a tire service professional to find, and Toyota and Hyundai say a tire that needs frequent inflating should be checked by their dealer. A low tire with a bulge, exposed cord or a deep cut is finished: do not keep driving on it (see the damage rule in when to replace tires).

Nitrogen: what the makers say

Some tire shops fill tires with nitrogen. USTMA says that for normal tire service nitrogen inflation is not necessary, but is permissible, as it may contribute to minor reductions in pressure loss, and that other leak paths (punctures, the bead, the valve, the wheel) may negate the benefit; it adds that nitrogen and air can be mixed in any proportion and that "Use of nitrogen alone is not a replacement for regular inflation pressure maintenance." Michelin's Canadian page says the same about mixing and says its tires deliver their expected performance with air or nitrogen as long as the vehicle maker's pressure is respected. So a nitrogen-filled tire is checked the same way, and topped up with air if nitrogen is not at hand.

Hybrids and electric cars

The Toyota Camry Hybrid manual we read gives the same inflation steps as the other manuals, with nothing hybrid-specific on the pressure pages. GM's tire pressure warning in the Chevrolet manual lists reduced range for electric vehicles among the effects of underinflation. Tesla's owner's manual site refused our request, so we cannot say what it prints.

Three traps that leave a tire wrong while the check feels done

Trap one: inflating to the number on the tire. It is molded in the rubber, and it is the maximum, not the target. Michelin, Bridgestone, Continental, Goodyear's bulletin and the trade body all say so. Never inflate a tire above the maximum pressure molded on its sidewall. The number to inflate to is on the vehicle's placard or in the owner's manual, not on the tire.

Trap two: measuring after a drive and fixing the number. The reading is high because the tire is warm, and the fix people reach for is to let air out. Do not let air out of a tire that is warm from driving: the higher reading is normal, and the tire will be underinflated once it cools. Check again when it is cold. Where a tire maker gives an add-air figure for a warm tire, it is about 4 to 5 psi, and Bridgestone and Michelin add a cold recheck.

Trap three: trusting the first thing that gives a number. That can be the pump's built-in gauge, which Michelin and Bridgestone both say may be inaccurate, or the dashboard light, which the federal rule sets to trip at 25 percent below the label. Neither is a substitute for your own gauge on a cold tire. If the low tire pressure light comes on while you are driving, or a tire looks flat, slow down smoothly, avoid hard braking and sudden steering, pull off to a safe place and stop as soon as possible to check the tires.

Three typical situations

These are composite scenarios, not individual customers. They are built only from facts already on this page.

The gas-station check. A driver stops at a pump after a 20-minute drive, measures 39 psi on a tire whose label says 35, and is tempted to let four pounds out. Hyundai, Kia and Subaru say warm tires normally read several psi above the cold figure, and Toyota, Hyundai, Kia, Subaru, Mazda, Volkswagen, USTMA and Michelin's pages say not to release air from a warm tire. The driver leaves it, and measures again next morning before the first drive.

The wheels were changed. A driver puts on new wheels and a different tire size and keeps inflating to the old label. The federal wording in the Chevrolet and Mazda manuals says that for a different size the proper pressure has to be determined for those tires, and the Nissan Altima manual shows that even one car's recommended pressure changes with the tire size (32 or 33 psi, in its table). The driver asks the tire shop which pressure fits the new size.

The spare nobody checked. A driver has a puncture, reaches for the compact spare and finds it nearly flat. Chevrolet and Nissan say their systems do not monitor the spare, so there was no light; Chevrolet, Toyota and Nissan print 60 psi for a compact spare. The driver adds it to the monthly list, as the Hyundai and Kia manuals ask.

What this page cannot tell you

We did not test any gauge, any tire or any pressure setting. We cannot say that any gauge is accurate: the accuracy figures above are a seller's claims about its own products, and we found no independent test of tire gauges that we could read. We read the tire pages of eight owner's manuals, each for one model (Chevrolet Equinox 2023, Toyota Camry Hybrid, Nissan Altima 2023, Hyundai Elantra 2023, Kia Sportage 2024, Mazda MX-5 2023, a Subaru manual in its US edition, and the Indian edition of the Volkswagen Tiguan manual), so what they print is not necessarily what your car's manual prints. Your own manual and your own label win. We could not read the manuals of Ford, Honda, Tesla and others, or the NHTSA website, because those sites refused us or did not load, and we did not get around that; everything federal here comes from the text of the rules in the Code of Federal Regulations.

What could we not read for this page, and does PulsCar fill the gap? We could not read the owner's manuals of Ford, Honda or Tesla, the NHTSA consumer pages, or the Consumer Reports, Wirecutter and Tire Rack pages on gauges, because those sites refused us or did not load, and we did not get around any of them. PulsCar does not fill the gap: its free sound check is a 30-second engine sound check and does not measure tire pressure. For a car we could not read, your own manual and label win over anything printed here, and the best use of this page is its questions: what does your label say for front, rear and spare, what does your manual call cold, and what does it say to do with a warm tire.

Your action plan: now, this month, this season

Now (five minutes). Find the label on your driver's door pillar, or in your manual if it is not there, and write down the front, rear and spare figures. Check where your gauge came from; if all you have is the pump on the street, plan to buy one with a range that reaches 60 psi.

This week. Measure all four tires and the spare cold, before the first drive of the day. Correct them, measure again, and put the caps back. If one tire is lower than the others, correct it, look for a nail in the tread (Mazda's check) and measure it again at your next check: a tire that keeps needing air is a shop visit, not a habit.

Every month, and before a long trip or heavy load. Repeat the check; makers ask for monthly or more, and USTMA asks for extra checks before long trips, heavy loads, towing and sustained high speed.

Each new season. Cold weather will pull the numbers down, and the first cold morning is the time to measure. If the low tire pressure light comes on while you are driving, or a tire looks flat, slow down smoothly, avoid hard braking and sudden steering, pull off to a safe place and stop as soon as possible to check the tires. Our tire pressure light guide covers what to do after you have checked.

Sources and documents

Every page below was read on 11 November 2026 and saved as text. Marks: 🟢 federal text. Maker, trade body and retailer pages are named in words. Where a page carried no date, we say so.

  1. 🟢 49 CFR 571.110, Standard No. 110, tire selection and rims, the placard (eCFR)
  2. 🟢 49 CFR 571.138, Standard No. 138, tire pressure monitoring systems (eCFR)
  3. US Department of Energy, fueleconomy.gov, Keeping Your Vehicle in Shape (read; the fuel-economy figures are not used on this page)
  4. USTMA (U.S. Tire Manufacturers Association), Tire Care and Safety Guide, 2024 PDF
  5. Goodyear, Product Service Bulletin 2015-25, Tire Inflation Recommendations for Auto and Light Truck Tires, 15 December 2015
  6. Bridgestone, How to Check Tire Pressure with a Tire Pressure Gauge (undated)
  7. Bridgestone Americas, Proper Tire Inflation and Tire Pressure (undated)
  8. Michelin USA, How to Properly Inflate Your Car Tires (undated)
  9. Michelin USA, tire pressure page (undated)
  10. Michelin Canada, How to check tire pressure (undated)
  11. Michelin Canada, How to Inflate Tires Properly (undated)
  12. Continental Tire, How to Check Tire Pressure: Step-by-Step Guide (undated)
  13. Cooper Tire Canada, Impacts to Tire Pressure During Cold Weather (undated; the page title reads Goodyear Tires)
  14. Nokian Tyres, Tire pressure, 30 April 2024
  15. JACO Superior Products, FAQs, Tire Pressure Gauges (seller; undated)
  16. Popular Mechanics, The 6 Best Tire Pressure Gauges (editors' list, not a test; cited for its criteria only)
  17. Mavis, how to check tire pressure safely (retailer; undated)
  18. 2023 Chevrolet Equinox Owner Manual, pp. 104 and 281-283
  19. Toyota Camry Hybrid Owner's Manual (file OM06261U, model year not printed in the pages we read), pp. 115, 444-448, 458-461, 550
  20. 2023 Nissan Altima Owner's Manual, pp. 5-6 to 5-8 and 8-28 to 8-33
  21. 2023 Hyundai Elantra Owner's Manual, pp. 8-13 and 9-32 to 9-34
  22. 2024 Kia Sportage Owner's Manual, US online edition, Tires and wheels and Checking tire inflation pressure
  23. 2023 Mazda MX-5 Miata Owner's Manual, pp. 4-114, 4-115, 6-34, 6-35, 8-31 and 8-32
  24. Subaru Owner's Manual, US edition (model A2630BE-A, edited 23 December 2022), pp. 541-542
  25. Volkswagen Tiguan owner's manual, Volkswagen India edition 11.2021, not the US edition
  26. PulsCar home page

Pages we could not read, and did not get around: the NHTSA website (access refused), the Tesla, Ford and Honda owner's manual sites (refused or unavailable), State Farm (login), Wirecutter and Tire Rack (refused), Consumer Reports and Car and Driver gauge pages (not found), and the product pages of two gauge sellers (rate-limited).

Prices verified 11 November 2026 on the pages they are carried from: the gauge price statements are Continental's and Popular Mechanics', each as printed. Technical documents verified 11 November 2026. Written by PulsCar, which publishes this guide and sells no tire gauges.