💡 The answer in 60 seconds

Check every tire in several spots across and around the tread, with the wear bars, a tread depth gauge or a coin, and act on the shallowest spot. A tire at 2/32 inch (1.6 mm) of tread or less in any major groove, or with its wear bars level with the tread, is worn out: replace it now and do not keep driving on it. If cord or fabric shows anywhere, or the tire has a bulge or a blister, or the sidewall a deep cut or open crack, do not keep driving on it at all: fit the spare, or have the car towed to a tire shop. A penny tells you whether you are above or below 2/32 inch; a quarter does the same for 4/32 inch, the depth where Bridgestone says to begin planning for new tires, where AAA and Consumer Reports say to start shopping for wet roads. The Hyundai, Kia, Mazda and Subaru manuals add that you should not wait for the wear band to form; they print no depth beyond the 1.6 mm indicator. For snow, Bridgestone says 5/32 inch. The federal texts we read set no minimum for a private car; the four state texts we could read say 2/32 inch.

This page answers one question: how do you check the tread depth of your tires, what is the legal minimum and the recommended minimum, and when do you replace. It is not about how old a tire may be or what damage ends a tire (our when to replace tires guide covers age, damage and repairs), how long tires last, which tire to buy (best tires), or the air pressure (see how to check tire pressure). PulsCar publishes this guide; it sells no tread gauges or tires, and no link on this page is an affiliate link. We did not test any gauge, any tire or any test method. Everything below is what vehicle makers, tire makers, the tire industry's trade body, an automobile club, a consumer magazine, a trade magazine and the texts of federal and state rules print, each named and read between 5 and 15 November 2026 (the eight owner's manuals on 5 November). 🟢 Official marks a federal or state text; every other statement is attributed to the maker or body that prints it, and where they disagree we show them side by side, never averaged.

The five steps at a glance

Step 1. Find the wear bars. Small raised bars across the bottom of the main grooves; a mark on the sidewall (Toyota: "TWI"; Michelin: the Michelin Man) shows where they are
bars level = worn out
Step 2. Measure with a gauge. Probe in the groove, shoulders flat on the tread blocks, read 32nds of an inch or millimeters. This is the only step that gives a number
read each spot
Step 3. Or use a coin. A penny checks the 2/32 inch line, a quarter checks the 4/32 inch line
penny 2/32, quarter 4/32
Step 4. Check several spots. Every tire, across the width and around the circumference; keep the gauge off the wear bar
shallowest spot decides
Step 5. Decide. At 2/32 inch or less: replace now. Near 4/32 inch: plan the purchase, sooner for rain. For snow: more tread
see the decision table

What you need: three tools, and what each one can tell you

You need good light, a flat place to park and one of three things: the wear bars the tire already carries, a tread depth gauge, or a coin. They answer different questions, so it helps to know which question you are asking before you pick one.

The wear bars (free). Raised bars in the bottom of the main grooves. USTMA, the U.S. tire makers' trade body: "will appear on the tire when the tread is worn to 2/32” (1.6 mm)". They answer one question: has this spot reached the line
yes or no at 2/32 inch
A tread depth gauge (a few dollars, per Michelin). Bridgestone: "an inexpensive simple graduated probe gauge will work just fine." This is the only one of the three tools that gives a number, so it also tells you how far you are from 4/32 or 5/32
a number in 32nds or mm
A coin. A U.S. penny checks the 2/32 inch line, a quarter checks the 4/32 inch line (Bridgestone). Quick and free, but each coin answers one question at one depth
above or below one line

They differ in how much they tell you: a reading of "above the line" on a coin or a bar can hide a tire that is close to it. Michelin's own page says a gauge "gives a more precise reading and costs only a few dollars."

Step 1: find the wear bars

New passenger and light-truck radial tires sold in the United States must have them, because the federal tire standard requires it (it does not apply to some tires, such as T-type temporary spares, special trailer tires and tires with rims of 12 inches and below). 🟢 FMVSS No. 139 says each tire "shall have not less than six treadwear indicators spaced approximately equally around the circumference of the tire that enable a person inspecting the tire to determine visually whether the tire has worn to a tread depth of one sixteenth of an inch". One sixteenth of an inch is 2/32 inch, or 1.6 mm. That rule governs how a new tire is made. It does not tell an owner when to retire it, a point the legal section below comes back to.

What the bars look like and where to find them, in the makers' words:

  • Pirelli: "These bars are chunks of rubber that span the grooves in the tread at different points around the circumference of the tire."
  • Continental: "Tread wear indicators are spaced evenly through the main grooves in the tire tread. If they are flush with the level of the tread, then the tire must be replaced."
  • BFGoodrich: "Raised rubber bars molded into the bottom of the main tread grooves, set at 2/32 of an inch."
  • Toyota (Camry Hybrid manual): the manual says a "TWI" mark or a symbol molded into the sidewall of each tire shows where they are. Michelin says the position of its indicators is shown by the Michelin Man symbol on the sidewall.

Some tires add a second kind of indicator. Michelin Canada describes a "wear to check" design in which, if only mark 3 is visible, "wear is between 50% and 75%", and if none are visible, "it’s your cue to change your tires!" Cooper Canada describes a Wear Square that ends "with an exclamation mark when the tread reaches 2/32s of an inch". Nokian says its latest tires carry a driving safety indicator, "a set of numbers (an indicator bar) that shows the tread remaining on the tires." These are features of particular tires and the makers' own claims; if your tire has one, its printed instructions win over this page.

How many bars must you see, and where? The sources are not identical, and it matters:

Chevrolet (Equinox 2023 manual): "The indicators at three or more places around the tire can be seen." Replace the tire if so
three or more places
Pirelli: worn down until flush with "any of the tread wear indicator bars", it is time to replace the tire, even if the tread is higher elsewhere
any one bar
Bridgestone (Canadian site): "Replace any tire where the tread ribs become flush with the indicator bars." The same page says the indicators are "at various places around the tire"
flush with the bars
Toyota (Camry Hybrid manual): "Replace the tires if the treadwear indicators are showing on a tire."
indicators showing
Nissan (Altima 2023 manual): "When the wear indicators are visible, the tire(s) should be replaced."
indicators visible
Volkswagen (Tiguan, Indian edition 11.2021): "The tyre must be replaced at the latest when the tread depth is just down to the tread wear indicator."
at the indicator, at the latest

Chevrolet's three-places rule is the most specific, and Pirelli's any-one-bar rule is the most cautious. Our reading is that they describe the same worn tire from two sides: if you can see one bar level with the tread, treat that tire as worn out and check the other tires, and do not wait for a second and third bar. (That is our advice; Chevrolet and Pirelli do not say it.)

Do not wait for the whole band. Four of the eight manuals say more than "replace when you see it". Where wear is even, the bars show as a solid band across the tread, and the makers do not want you to wait for the band:

  • Hyundai (Elantra 2023): "Do not wait for the tread surface to become level with the tread wear indicators before replacing the tire."
  • Kia (Sportage 2023): "Do not wait for the band to appear across the entire tread before replacing the tire."
  • Mazda (MX-5 2023 manual and CX-5 2023 web manual): "You should replace the tire before the band crosses the entire tread."
  • Subaru (Legacy and Outback, US edition, edited December 2022): "For safety, inspect the tire tread regularly and replace the tires before their tread wear indicators become visible." The same manual says that when the indicator becomes visible the tire "is worn beyond the acceptable limit and must be replaced immediately."

Firestone, a tire-service retailer, says something close: "Since the tread depth bars indicate the legal tire tread depth limit for most states, we recommend replacing your tires before they reach this point." All of these are warnings about the same thing. The wear bars mark the end of the tire, not the start of a comfortable margin.

Step 2: measure with a tread depth gauge

The gauge is the best of the three tools because it returns a number. The makers describe the common probe type the same way.

Probe gauge. Pirelli: "The graduated probe has a thin, retractable rod, a perpendicular “foot,” and a cylinder with measurements marked on it." To use it, "fully extend the rod and insert it into one of the grooves. Then push down the “foot” of the gauge until it firmly rests on two elevated ribs of the tread on either side of the groove." Continental says the same in one line: "insert the probe bar into the groove and push the shoulders flush with the tread." Bridgestone adds: "Probe-Style: Insert probe fully into the lowest tread groove, press base flush, and record the marking." Firestone: "place the measuring pin into the center of the main tread groove on your tire and push down until it makes contact with the tire on either side of the gauge."

Digital gauge. Bridgestone: "Turn on, place the tip in the groove, and read the digital display." A digital gauge needs a battery (our note).

Park first. Michelin's tread-gauge instruction starts with the car: "Make sure the car is on hand brake and in first gear (for manual gearboxes) or park (for automatics)." Michelin Canada adds: flat surface, engine off, handbrake on. Read the scale in good light (our advice).

Units. In the United States tread is measured in 32nds of an inch. One 32nd is 0.79 mm (our arithmetic), so 2/32 inch is 1.6 mm, 4/32 inch is 3.2 mm, 5/32 inch is 4.0 mm and 6/32 inch is 4.8 mm. Bridgestone says "All gauges should measure in both 32nds of an inch and millimeters," and Pirelli says the probe's shaft "usually displays the measurements in both 32nds of an inch and millimeters." Bridgestone writes that "New tires typically come with 10/32” or 11/32” tread depths", and says some truck, SUV and winter tires start deeper. From 10/32 to 2/32 is 8/32 inch of rubber, about 6.4 mm (our arithmetic).

Which tread depth gauge should you buy, and does PulsCar sell one? PulsCar sells no tread gauges and we tested none, so no model is named here. What the makers' pages let you compare: the type (probe or digital) and whether it reads 32nds of an inch and millimeters; a digital one also needs a battery (our note). A seller's listing we read, AME's digital gauge, says it displays "tread depths in millimeters, inches and fractions at 1/32 increments"; it prints no accuracy figure on the page we saved, and we found no independent test of tread gauges, so any claim that one gauge is more accurate than another is the seller's. If you only want to know whether a tire is above or below a line, a penny or a quarter costs nothing. PulsCar's free sound check is a 30-second engine sound check and does not measure tread.

Step 3: the penny test and the quarter test

If you have no gauge, a coin does one job well. The two tests are the same method at two depths, and the sources describe them with small differences that are worth seeing side by side.

Bridgestone, penny: "Turn the penny so that Lincoln’s head points down into the tread." If the top of his head disappears between the ribs, the tread is still above 2/32 inch; if you can see his entire head, it has reached the end of its useful life
2/32 inch line
Pirelli, penny: if there is a space between the top of Lincoln's head and the tread, or the tread is flush with the top of the head, the tire is no longer safe and needs changing; "Check different parts around tire, and if any point fails the test, get new tires."
fails at any point
Tire Industry Association (TIA), penny: "If the top of Lincoln’s head is visible at any point in any major tread groove, it’s a good sign that the tire needs to be replaced so drivers should take the vehicle to a tire professional."
top of head visible = replace
Cooper (Canada), penny: insert the penny into "the most worn groove"; if the top of the head is visible, "you need to replace the tire."
most worn groove
Bridgestone, quarter: "If the tread covers part of Washington’s head, you have at least 4/32”. If you can see all of Washington’s head, your tread is dangerously shallow for wet conditions."
4/32 inch line
Consumer Reports, quarter (2018): "If you can see the top of Washington’s head, it’s time to start shopping for new tires, because there’s only 4⁄32 inch of treadwear left."
start shopping

The wording differs on what "visible" means. Act on the strictest reading (our advice): put the coin in head first, and if the top of the head shows at any spot, treat that spot as 2/32 inch or less. Two cautions come from the makers themselves. First, a coin tests one groove at one spot: Bridgestone says "Even if parts of your tread are deeper than 2/32”, you should still replace the tire when any areas fail the penny test." Second, the penny line is not the whole story. Bridgestone says the penny test "may not be the best indicator of whether your tires are safe for the road" and that "Tire performance can diminish significantly before your tread hits 2/32”."

The penny test is contested, and the sources disagree about how far. The Safe Tread Alliance, a coalition that includes a tire retailer, a road-safety foundation and others, asks drivers to retire the penny test. In its December 2025 release it says "The penny test has given Americans a false sense of security for far too long" and asks drivers to use a quarter instead. Modern Tire Dealer's April 2026 article records the Tire Industry Association's chief technical officer, who says the association stays out of the 2/32 versus 4/32 debate and follows the federal 2/32 figure, and that suggesting a tire is not safe at 3/32 or 4/32 when the federal government has set 2/32 "becomes a slippery slope". The 2018 Consumer Reports article reports its tire program manager saying that manufacturers design tires to still function right down to the treadwear bars, and calls the penny test "a valid method for determining when tires must be replaced"; he adds "don't expect the worn tires to perform like new." We do not take a side: the penny tells you where the tire ends, the quarter where several sources say to start shopping, and which matters more depends on the weather you drive in. The Safe Tread Alliance's release is advocacy by an alliance that includes a tire retailer; we quote it as its position, not as a test result.

Where to measure, and how many spots

Tread wears unevenly, so one reading is never enough. The sources we read that say anything about it say to look at several places on each tire:

  • Michelin (U.S. routine tire care page): "Check the depth of the main tread grooves in several places across and around the tire, using the gauge as instructed by its manufacturer."
  • Pirelli: "you need to check the tread depth at various points around the tire’s circumference. You should use the smallest measurement as the basis for your decisions about replacing tires."
  • USTMA: "Replace tires when worn to 2/32” (1.6 mm) depth remaining anywhere on the tread face."
  • Bridgestone (penny page): "Pay special attention to areas that look the most worn." Bridgestone's gauge tip says to "Check inner, center, and outer edges of the tire, then average for accuracy." That is not the same as the rule above it, and the replacement rule is the one the same page puts first, so for the decision use the shallowest reading.

The state and federal texts we read say where to take the reading, and they differ in detail (the texts are in the next section):

  • 🟢 Washington: "in any two major tread grooves at three locations equally spaced around the circumference of the tire".
  • 🟢 Utah (R714-161-8): "any two adjacent major tread grooves at any location around the circumference of the tire", and the tread depth "may not be measured on the tread wear bar".
  • 🟢 New York: readings "shall be taken in two adjacent major grooves showing the most tread wear", and "Do not check tread depth at tread wear indicator bar or tie bar."
  • 🟢 49 CFR 393.75 (commercial vehicles): measured "in a major tread groove", and "The measurement shall not be made where tie bars, humps or fillets are located."

Michelin's U.S. routine tire care page puts the area this way: the legal minimum is "2/32nd's across the central three-quarters of the tread width and round its entire circumference." None of the texts we read uses that wording.

A major groove is one of the wide grooves running around the tire, and the shoulder is the outer edge of the tread where it curves toward the sidewall (our plain-language definitions). Do all four tires, and the spare if it is a full-size tire. For a compact spare the manuals give their own rules: Hyundai says to replace it "when you can see the tread wear indicator bars on the tire", Nissan says to "Replace the spare tire as soon as the tread wear indicators appear", and Mazda's CX-5 web manual says its temporary spare has "a tread life of less than 5,000 km (3,000 miles)" and that it may be shorter. Look at both shoulders of the front tires, including the inner side (our advice): the sources link one-sided wear to alignment.

The legal minimum: what the federal and state texts say

Owners are told in many places that there is a legal minimum tread depth. The sources do not agree on whether a federal rule applies to a private car. We read the federal texts and four state texts ourselves.

Federal tire standard. 🟢 FMVSS No. 139 (49 CFR 571.139) governs how new tires are made; its treadwear-indicator paragraph is quoted above. It says nothing about when a tire in service must be retired.

Federal rule for commercial vehicles. 🟢 49 CFR 393.75 reads: "Any tire on the front wheels of a bus, truck, or truck tractor shall have a tread groove pattern depth of at least 4⁄32 of an inch when measured at any point on a major tread groove", and "Except as provided in paragraph (b) of this section, tires shall have a tread groove pattern depth of at least 2⁄32 of an inch when measured in a major tread groove." It names buses, trucks and truck tractors and sets no figure for a private car.

What makers and trade writers say about a federal rule. Several of them describe 2/32 as federal. Read them next to the texts above:

Michelin (U.S. tread depth page): "The federal minimum for passenger vehicle tires is 2/32 inch (approximately 1.6 mm)." It adds that driving below that is illegal
calls it federal
Bridgestone (penny test page): "The U.S. Department of Transportation recommends replacing tires when they reach 2/32”, and many states legally require tires to be replaced at this depth."
DOT recommends, many states require
Goodyear (press release, May 2018): "The National Highway Traffic Safety Administration recommends that tires be replaced when they are worn to 2/32-inch tread depth."
NHTSA recommends
Pirelli (U.S. tire tips page): "While there is no national law in the U.S. specifying minimum legal tread depth, most state laws require a tire to have at a tread depth of at least 2/32nds of an inch."
no national law
Modern Tire Dealer (trade magazine, April 2026): "The federal government has set the legal minimum tread depth for passenger tires at 2/32-inch" and, a few lines on, "states have the authority to enforce tire removal at their own levels."
federal minimum; states enforce

We did not find a federal text that sets a minimum tread depth for a private car, and we could not read NHTSA's own tire pages (the site refused our request, and we did not get around it), so we cannot say whether an NHTSA recommendation of 2/32 exists in writing; Goodyear, Bridgestone and Pirelli attribute one to NHTSA or the Department of Transportation. What every one of these sources, and the federal indicator rule, agree on is the number: 2/32 inch, or 1.6 mm. They differ on who sets it.

State texts. Four state texts were readable on 15 November 2026, or on 5 November for the first two. Each is a rule about when a tire is unsafe or fails an inspection.

🟢 Washington, RCW 46.37.425 (unsafe tires): a tire is unsafe with "A tread depth of less than 2/32 of an inch measured in any two major tread grooves at three locations equally spaced around the circumference of the tire", or if "the tread wear indicators contact the road in any two major tread grooves" at those locations
less than 2/32 inch
🟢 Utah, R714-161-8 (inspection): the inspector issues a rejection when "any tread wear indicator contacts the ground" or "the tread depth is less than 2/32 when measured in any two adjacent major tread grooves at any location around the circumference of the tire"
less than 2/32 inch
🟢 Pennsylvania, 67 Pa. Code § 175.80 (inspection): reject if "A tire has two adjacent treads with less than 2/32-inch tread remaining at any point", with 4/32 inch for front tires on vehicles over 10,000 pounds, or if the wear indicators "contact the road in any two adjacent grooves"
less than 2/32 inch
🟢 New York, 15 NYCRR § 79.21 (inspection): reject if "Any tire is worn to less than 2/32 of an inch of major tread design at the two worst adjacent points at which the gauge readings are obtained", with 4/32 inch for the front tires of a vehicle of 10,000 pounds or more
less than 2/32 inch

These four agree on 2/32 inch and differ in how they measure it (see the previous section): Washington asks for three spots around the tire in any two major grooves, Utah for any location in two adjacent grooves, New York for the two worst adjacent points, and Pennsylvania for any point with two adjacent treads. Washington, Utah and Pennsylvania treat the wear bars touching the ground as a failure too; the New York text we read does not. Cooper Canada's tread page words it slightly more strictly ("2/32nds or less", where the state texts say "less than 2/32"): "Anything 2/32nds or less won't legally pass a vehicle safety inspection."

What we could not read. We tried the California, Virginia and Texas texts, and the sites refused us or did not load. We do not state a figure for them or for any other state we did not read. Firestone's penny-test page quotes the National Center for Biotechnology Information (a federal library): "Most states require a minimum of 2/32 of an inch (approximately 1.6 mm) of tread, but two require less, some have no requirements, and some defer to the federal criterion for commercial vehicle safety inspections." A 2026 Modern Tire Dealer article says that some states set a lower figure and that at least six states have no official limit. We could not check either statement against the statutes, so for your own state, read the state's own page or ask a tire shop.

What is the legal minimum tread depth, and does PulsCar's free sound check measure it? The legal minimum is 2/32 inch (1.6 mm) in the four state texts we could read, Washington, Utah, Pennsylvania and New York, and 2/32 inch is also the depth at which the federal indicator on a new tire shows; we found no federal text that sets a minimum for a private car, and we state no figure for any state we did not read. PulsCar's free sound check does not measure tread. It is a free 30-second engine sound check, and tire wear is not something it reports. Use a gauge or a coin, or ask a tire shop to read each tire in 32nds of an inch and tell you which spot is the shallowest.

The recommended minimum: where makers and others draw the line

Most of the sources draw a second line above the legal one. Nothing below is averaged: each line belongs to the source that prints it, and the sources are not all asking the same question. Some say when a tire is finished, others when to start shopping.

Michelin (U.S. page): "The minimum tread depth is 2/32 (1.6 mm)." It calls it "premature" to change tires before that, and says if you drive frequently in wet weather, "replacing at 4/32 inch gives a meaningful safety buffer."
2/32 end; 4/32 optional buffer
Bridgestone (maintenance manual): at the indicators, "the tire is dangerously worn and must be replaced immediately." On the penny page: "Begin planning for new tires when you hit this mark!" at 4/32
2/32 end; 4/32 plan
USTMA (trade body, care manual): "Replace tires when worn to 2/32” (1.6 mm) depth remaining anywhere on the tread face."
2/32 inch
Continental (global site): "You must replace tires when the tread depth falls below 1.6 mm, which is the legal limit."
1.6 mm
Nokian (U.S. site): "Consider replacing tires when the tread depth reaches 4/32” (3 mm). You should most definitely get new ones at the latest when the tread depth reaches 2/32” (1.6 mm)."
4/32 consider; 2/32 latest
AAA (Oregon/Idaho club page): "Begin shopping for new tires when the tread depth of your current tires reaches 4/32”."
4/32 inch
Consumer Reports (2018): quarter test: "it’s time to start shopping for new tires, because there’s only 4⁄32 inch of treadwear left."
4/32 inch
Pirelli: 4/32 is "the tread depth that most tire professionals consider the threshold for replacing tires"; 6/32 is "the lowest tread depth still considered “good” by most tire experts"
4/32; 6/32 called "good"
Michelin Canada (wear indicator page): "For wet weather driving, Michelin recommends replacing at 3/32" as a practical safety threshold."
3/32 inch for wet weather
Tires Plus (retailer, tread chart): "6/32 and above" is "In good condition"; "Between 4/32 and 5/32" is "Time to inspect for replacement"; "2/32 and lower" is "Replace as soon as possible"
6/32 good; 4-5/32 inspect

Modern Tire Dealer asked several tire makers in 2026 and reported what some big dealers say, which is where several other positions on the record come from:

  • Hankook: "follows the U.S. Tire Manufacturers Association guideline that once a tire tread wears down to 2/32nds of an inch anywhere across the tread face, it should be replaced" (its spokesperson, as quoted by the magazine).
  • Goodyear: considers tires "legally worn out at 2/32-inch" and "also recommends monitoring tread depth once it reaches 4/32-inch, as wet traction and braking decline."
  • Bridgestone: "complies with state and federal regulations, which state that drivers must replace their tires when the tread depth reaches 2/32 of an inch," and its limited mileage warranty "references the federal limit of 2/32nds", though it "allow[s] consumers to submit a limited mileage warranty claim as high as 4/32nds."
  • Discount Tire (a retailer) recommends replacing at 4/32-inch and below; Monro says to start shopping at 4/32-inch.

Two further statements in the sources do not match each other. AAA's 2018 report says "The majority of tire manufacturers recommend tire replacement when the tread depth reaches 3/32”." Most maker pages we read print 2/32 as the end of a tire; Michelin Canada's wear indicator page also prints 3/32 for wet weather. We do not know which makers AAA meant. And the Safe Tread Alliance's December 2025 release, as printed by Work Truck Online, says "Independent testing has shown that vehicles with tires worn to 2/32 of an inch can take up to 87 feet longer to stop in wet conditions than those with 4/32 of an inch tread." The AAA report we read prints a difference of that size between new tires and tires worn to 4/32 inch, and it did not test 2/32 (AAA prints 296.51 feet for the Camry's average wet stop from 60 mph on the worn tires and a difference of 87.07 feet; about 209.44 feet on new ones is our mean of AAA's two new-tire averages). We do not know which tests the alliance means.

What the AAA test did and did not measure. AAA's 2018 study tested a 2017 Toyota Camry and a 2017 Ford F-150 on six all-season tire models each, new and "artificially worn" to 4/32 inch with Michelin North America's equipment. Its finding: "An increased stopping distance of 42 percent for the Toyota Camry and 44 percent for the Ford F-150." AAA says the 4/32 depth is "conservative in comparison to most recommendations for tire replacement" and recommends that consumers "begin shopping for replacement tires when tread depth reaches 4/32”." It tested two vehicles on wet pavement at one depth, so it says nothing about dry roads or 3/32. Our when to replace tires guide sets out the test in more detail.

How to read the lines. Put together, the sources say three things (this is our summary, not a maker's statement). At 2/32 inch the tire is finished, and the tire makers and the trade body we read agree on it. At about 4/32 inch, several makers, AAA and Consumer Reports say wet-road performance is already falling, and the question is when to shop rather than whether the tire is legal. Below 4/32 inch in rain, the sources that draw a line say to start planning or shopping. Which applies to you depends on your climate; the makers do not set one answer.

What eight owner's manuals say about tread

Your car's own manual is the most specific document you have. We read the tire pages of eight manuals on 5 November 2026, each for one model, so what they print is not necessarily what your manual prints. All eight tell you to replace a tire when its wear indicators show (Chevrolet: at three or more places); the five that print how high the indicators are (Chevrolet, Hyundai, Kia, Subaru and Volkswagen) say 1.6 mm (1/16 inch, or 2/32 inch), and none of the eight prints a deeper figure for an ordinary tire (Toyota prints 4 mm for snow tires; see the winter section). They differ in how they word it.

Chevrolet (Equinox 2023): "Treadwear indicators appear when the tires have only 1.6 mm (1/16 in) or less of tread remaining." Replace the tire if the indicators can be seen at three or more places; inspect tires monthly
three or more places
Toyota (Camry Hybrid, US edition): "Check if the treadwear indicators are showing on the tires. Also check the tires for uneven wear, such as excessive wear on one side of the tread." Replace if the indicators show
indicators showing
Nissan (Altima 2023): "The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced."
indicators visible
Hyundai (Elantra 2023): "This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire. Replace the tire when this happens." And: "Do not wait for the tread surface to become level with the tread wear indicators before replacing the tire."
do not wait for level
Kia (Sportage 2023, online manual): "This shows there is less than 1/16 in (1.6 mm) of tread left on the tire. Replace the tire when this happens." And "Do not wait for the band to appear across the entire tread before replacing the tire."
do not wait for the band
Mazda (MX-5 2023; CX-5 2023 web manual): "Driving with worn tires is dangerous. Reduced braking, steering, and traction could result in an accident." Replace when the solid band appears; both texts say before it crosses the tread
before the band crosses
Subaru (Legacy/Outback, US edition): the indicator "becomes visible when the depth of the tread grooves decreases to 0.063 in (1.6 mm)"; replace before it becomes visible, and "must be replaced immediately" when it does
before visible; immediately
Volkswagen (Tiguan, Indian edition): "There are 1.6 mm (1/16 in) high wear indicators" "in the tread base of the tyres." "In most countries, the minimum tread depth required by law is 1.6 mm (1/16 in), measured in the tread grooves next to the tread wear indicators. Observe any deviating country-specific legal regulations."
at the indicator, at the latest

Three things stand out. First, no manual we read tells you to wait until a tire is almost bald: the wear indicator is the line, and four of the eight (Hyundai, Kia, Subaru and Mazda) say to replace before the band is fully formed. Second, the manuals say nothing about the 4/32 inch figure; it comes from tire makers, AAA and Consumer Reports, not from the vehicle makers we read. Third, the Volkswagen manual is the Indian edition and calls 1.6 mm the legal minimum in most countries, not in the United States in particular. We did not read the manuals of Ford, Honda, Tesla and others; the Ford and Tesla service pages we tried refused us, and we did not get around that.

Winter tires and snow: what the printed depths are

Winter is where most of the sources print a line higher than the 4/32 inch wet-road one, and they print it as a recommendation or a warning, not as a legal figure. Here they are side by side.

Bridgestone (tire life page): "You’ll want at least 5/32” of tread for winter traction."
5/32 inch (4.0 mm)
Nokian (U.S. site): "New Nokian Tyres winter tires have a tread depth of at least 10/32 of an inch (8 mm). The tread depth minimum for winter tires is between 5/32” and 6/32”", which Nokian converts to about 4 mm and 5 mm; "It is not recommended to drive on winter tires with a tread depth below that range."
5/32 to 6/32 inch
Continental (Canadian site): "Continental recommends using winter tires with the "Alpine symbol" on the sidewall and a tread depth of at least 4 mm in winter conditions"
4 mm (about 5/32 inch)
Michelin (U.S. site): winter tires have a snowflake design "to show the location of additional tread wear indicators. They are 0.15 inch high. Replace your Winter tires once they are worn down to the level of the 'snow' tread wear indicators."
0.15 inch (about 5/32)
Toyota (Camry Hybrid manual): "If the tread on snow tires wears down below 0.16 in. (4 mm)": "The effectiveness of the tires as snow tires is lost."
0.16 inch (4 mm)

Converted (our arithmetic), 5/32 inch is 4.0 mm, 6/32 inch is 4.8 mm, Continental's 4 mm is about 5/32 inch, and Michelin's 0.15 inch is about 3.8 mm or 4.8/32 inch. The five winter figures sit close together, between about 3.8 mm and 4.8 mm (Toyota's 0.16 inch is 4.1 mm, our arithmetic), well above the 1.6 mm that the wear bars of an ordinary tire mark; Michelin's Canadian page prints a lower winter figure, 4/32 inch (3.2 mm). Bridgestone's spokesperson, speaking of winter tires, explains why in Modern Tire Dealer: "At 4/32nds, the biting edges in a tire’s tread pattern begin to stiffen and lose their ability to grab the snow. By 2/32nds, most of those pattern features are completely gone, making it nearly impossible for the tire to gain traction in winter conditions."

What this means in practice (our summary of the printed figures): if you drive on snow, the wear bars are not the end of the question. A tire that is above the legal line can be below the makers' winter line, and the Nokian, Continental, Michelin and Toyota figures are for winter or snow tires, Bridgestone's 5/32 is printed under "Snow Driving" without naming a tire type, and the sources we read print no separate depth for all-season tires used in snow. Our best all-season tires guide covers what the all-season label does and does not mean. Nokian's page also says to "check tires at least once a month"; on any tire, check before the first cold spell, not during it.

Reading the result: what to do at each reading

This is where the numbers become a decision. The first row is the only one that is a rule; the others are the choices the sources leave open. The safety wording is our own, built from the maker texts above, and it is the same wherever it appears on this page. What "now" means in practice: Bridgestone says the tire "must be replaced immediately", and Cooper Canada recommends taking the vehicle "to a trained tire service professional immediately"; neither says a long trip on it is fine, and neither do we.

A tire at 2/32 inch (1.6 mm) of tread or less in any major groove, or with its wear bars level with the tread, is worn out: replace it now and do not keep driving on it. If cord or fabric shows anywhere, or the tire has a bulge or a blister, or the sidewall a deep cut or open crack, do not keep driving on it at all: fit the spare, or have the car towed to a tire shop.

2/32 inch (1.6 mm) or less in any major groove, or the wear bars level with the tread. Makers and the trade body say 2/32 or less; the four state texts say less than 2/32, and three of them (Washington, Utah, Pennsylvania) also reject wear bars touching the road. Bridgestone: "must be replaced immediately."
replace now
Between 2/32 and 4/32 inch. Above the line that ends a tire. Bridgestone calls under 4/32 dangerously shallow for wet roads, Michelin Canada says replace at 3/32 for wet weather, and AAA and Consumer Reports say to start shopping
our advice: plan; in rain, replace
Around 4/32 inch and you drive in rain or snow. AAA's test found wet stops 42 to 44 percent longer than on new tires at this depth; Bridgestone says 4/32 is where to begin planning; Michelin calls replacing here a buffer for wet weather
our advice: book it
Between 4/32 and 6/32 inch. Above both lines. Pirelli calls 6/32 the lowest depth most tire experts still consider "good"
keep checking monthly
Winter is coming and the tread is under 5/32 inch. Bridgestone, Nokian and Continental print winter figures of 5/32, 5/32 to 6/32 and 4 mm
plan before the first snow
One tire at the line and three above it. That tire is finished whatever the other three read (USTMA: 2/32 "anywhere on the tread face"); whether to replace one, two or four is in our when to replace tires guide
replace that tire
Your gauge and your coin disagree. Our advice: believe the lower reading and have a tire shop read it in 32nds. Cooper Canada, on a failed penny test: take the vehicle "to a trained tire service professional immediately."
get it measured

How often to look? The sources that give an interval mostly say monthly: USTMA ("During monthly maintenance inspections, focus on proper inflation pressure, tread wear and tire damage."), Nokian ("check tires at least once a month"), BFGoodrich ("Once every month, or before you embark upon long road trips"), Michelin ("Monthly inspection for tire wear is recommended.") and the Chevrolet manual ("at least once a month"); Subaru's manual asks for a daily look for damage and abnormal wear. The pressure check in our tire pressure guide is the natural moment.

Uneven wear: what the pattern points to

A tire that wears evenly reaches the line everywhere at once; one that does not can be deep in the middle and at the wear bars on one shoulder. Since the replacement rule goes by the shallowest spot, the pattern matters twice: it tells you which spot to measure, and it points to a cause you should fix before new tires go on. The patterns the sources describe:

Both shoulders worn, center fine. Michelin: "chronic under-inflation, the edges are bearing too much load." Nokian: "Excessive wear on both sides of a tire usually translates to underinflated tires." Continental says the same for both shoulders
underinflation
Center worn. Michelin: "over-inflation, concentrating load on the middle of the tread." Nokian and AAA say the same
overinflation
One edge worn. Michelin: "alignment problem, the tire is running at an angle (camber or toe issue)." Nokian: "If the inner or outer edge is wearing faster, often it indicates issues with wheel alignment." Firestone: "Inner or outer shoulder wear can indicate misalignment"
alignment
Cupping or scalloping, a wavy pattern. Michelin: "worn shocks or struts, or a wheel balance problem." Nokian: a possible issue with the suspension, and tires may feel "slightly bouncy or noisier than usual." AAA: usually a sign of a problem with suspension or other wheel-assembly components
suspension or balance
Patches or diagonal wear. Nokian: "If tires are wearing in patches, it can be a sign of balancing issues." Michelin: "typically a mix of alignment, balance, and suspension issues." AAA: out-of-balance wheel or a manufacturing defect
balance, alignment, suspension
Saw-tooth edges on the tread blocks (heel and toe). Pirelli: the leading edge of each block wears faster than the trailing edge, and it "can usually be prevented or remedied by rotating tires."
rotation

Three of the manuals give a list of causes in their own words, and Hyundai's matches Kia's. Kia: "Abnormal wear is usually caused by incorrect tire pressure, improper wheel alignment, out of-balance wheels, severe braking or severe cornering." Mazda lists incorrect pressure, improper alignment, out-of-balance wheels and severe braking. Toyota asks you to "check the tires for uneven wear, such as excessive wear on one side of the tread" and names no cause.

What to do with that (the rotation step is the makers'; the rest is our summary):

  • Check the pressure first, because it is free and the pattern for it is clear: see how to check tire pressure.
  • Rotate on schedule. Michelin says tires should be rotated every 6,000 to 8,000 miles or as the vehicle maker says, and "at first sign of irregular wear, even if it occurs before 6,000 miles." Nokian says 4,000 to 6,000 miles and Kia 8,000. Prices and patterns are in our tire rotation cost guide.
  • If one edge is worn, ask about alignment. Continental also calls an alignment "a smart follow-up to replacing your tires". Our wheel alignment cost guide explains when an alignment is worth paying for and what to ask. If the car also pulls to one side, see why a car pulls to one side.
  • If the wear is cupped or patchy, or the car vibrates, the sources point to the suspension or balance, which is a shop's job; a steering wheel that shakes at speed is covered in steering wheel shaking.

Replacing a tire without finding the cause can wear the next one the same way; that is a reason to look, not to delay replacing a tire at the line.

Tread is not the only reason to replace a tire

This page is about tread. Two other limits can end a tire at any depth: damage (the safety wording above) and age. The tread reading says nothing about either. USTMA, for low-mileage cars, puts it directly: "tread wear will not tell you when it’s time for new tires." Chevrolet's manual says tires, including the spare, should "be replaced after six years, regardless of tread wear", and Michelin recommends replacing tires "ten years after their date of manufacture, regardless of remaining tread depth or apparent condition." The date on the sidewall is in how to read tire size; the age statements, the damage list and repairs are in when to replace tires. When you measure tread, look at the sidewalls at the same time.

One tire, two tires or four

If one tire is at the line and the others are not, the sources lean the same way and differ on how firmly. Chevrolet: "GM recommends replacing worn tires in complete sets of four." Mazda "strongly recommends that you replace all four tires at the same time." Kia: "It is best to replace all four tires at the same time. If that is not possible, or necessary, then replace the two front or two rear tires as a pair." Michelin: "The ideal is always four matching tires," and if replacing two, "fit both on the rear axle." The Tire Industry Association: if only one tire is replaced, "the best practice is to mount the new tire on the rear axle and pair it with the tire having the most remaining tread depth." If the worst tire is at the line it is replaced either way; the sources differ on whether to replace it alone, as a pair or with all four.

Three traps that leave a worn tire on the car

Trap one: reading one spot. A single reading on the middle rib proves nothing about a shoulder. Bridgestone says to replace a tire "when any areas fail the penny test," Pirelli to use the smallest reading as the basis for the decision, USTMA says "anywhere on the tread face", and the state texts we read measure in two major grooves (adjacent ones in Utah, Pennsylvania and New York), at three spots in Washington, at any point in Utah and Pennsylvania, and at the most worn grooves in New York. Averaging three readings, as Bridgestone's own gauge tip suggests, would hide the worst spot (our reading).

Trap two: treating "legal" as "good". The four state texts we could read, and the tire makers, put the end of a tire at 2/32 inch. Michelin says that the legal limit is "the minimum, not the ideal", and Bridgestone says "Tire performance can diminish significantly before your tread hits 2/32”." A tire that is above the line can still be a poor tire in the rain or the snow, which is why the 4/32 and 5/32 figures exist.

Trap three: replacing the tire and not the cause. The pattern of wear is the clue. A set of tires that wore out on one shoulder will do it again on an out-of-line car. Michelin says "Uneven wear pattern is always a signal that something else needs attention."

Three typical situations

These are composite scenarios, not individual customers. They are built only from facts already on this page.

The monthly check. An owner checks tire pressure once a month, as the sources suggest, and then measures the tread of each tire with a gauge. The front tires show the inner shoulder at 3/32 inch, above the 2/32 line but below 4/32, while the center and outer edge read more. The owner acts on the shallowest spot, which is the inner shoulder: the tire is in the zone where Bridgestone says to begin planning, and the uneven pattern points to alignment, so the owner books the new set and asks the shop about alignment when it is fitted.

The coin on a cold morning. A driver with a family trip coming puts a penny into the rear tire and sees the whole head. The driver has a tire at the penny line, and the rule on this page is the one given above: a tire at 2/32 inch (1.6 mm) of tread or less in any major groove, or with its wear bars level with the tread, is worn out: replace it now and do not keep driving on it. If cord or fabric shows anywhere, or the tire has a bulge or a blister, or the sidewall a deep cut or open crack, do not keep driving on it at all: fit the spare, or have the car towed to a tire shop. The driver has the tire replaced before the trip, not after it, and checks the other three tires with the same coin.

Before the first snow. A driver with winter tires on a car measures them in October. The reading is above the 2/32 line and the wear bars are not showing, so the tread passes the tests in the four state texts we could read, but the reading is below the 5/32 inch that Bridgestone says you will want for winter traction and below the 5/32 to 6/32 inch range Nokian prints. The winter figure is a maker's recommendation (Nokian: not recommended to drive below its range), so the sensible step is to replace before the season.

What this page cannot tell you

We did not test any gauge, any tire or any test method. We cannot say that a given tread depth gauge is accurate: the one gauge listing we read prints no accuracy figure, and we found no independent test of tread gauges that we could read. The AAA study is one study of two vehicles on wet pavement at one depth, 4/32 inch; the Safe Tread Alliance is an advocacy group and Modern Tire Dealer a trade magazine, and we quote them as positions, not as test results. Where Michelin, Bridgestone, Goodyear and others call 2/32 a federal minimum or a federal recommendation and the federal texts we read do not set one for a private car, we show both and do not settle it. The four state texts say what they say for Washington, Utah, Pennsylvania and New York; they are not a guide to your state. The eight owner's manuals are one model or model family each (Mazda: MX-5 and CX-5; Subaru: Legacy and Outback), and the Volkswagen one is the Indian edition, so your manual and your own tire's printed instructions win over anything here.

What could we not read for this page, and does PulsCar fill the gap? We could not read NHTSA's own tire pages (refused on 5 November), the California, Texas and Virginia state texts, or the Ford and Tesla service pages, because those sites refused us or did not load, and we did not get around any of them; we did not read the Honda, Ford or Tesla manuals. PulsCar does not fill the gap: its free sound check is a 30-second engine sound check and does not measure tread. For a state or a car we could not read, ask: what does your manual say about the wear indicators, what does your state's own page say about tread depth, and what does a tire shop read on each of your tires, in 32nds of an inch, at the shallowest spot.

Your action plan: now, this week, this season

Now (five minutes). Find the wear bars in the main grooves of one front tire, with a flashlight if you need one, and look at the sidewall for the "TWI" or maker's mark. Read the tire pages of your owner's manual for what it says about the indicators; four of the eight we read say not to wait for the whole band.

This week. Measure every tire, and a full-size spare, at several spots across and around the tread, with a gauge or a coin, and write the shallowest reading for each tire in 32nds of an inch. A tire at 2/32 inch (1.6 mm) of tread or less in any major groove, or with its wear bars level with the tread, is worn out: replace it now and do not keep driving on it. If cord or fabric shows anywhere, or the tire has a bulge or a blister, or the sidewall a deep cut or open crack, do not keep driving on it at all: fit the spare, or have the car towed to a tire shop. For a tire between 2/32 and 4/32 inch, plan the purchase; if you drive in rain, our advice is to replace it by 3/32 (Michelin Canada's wet-weather line).

Every month, and before a long trip. Repeat the check when you check the pressure; USTMA, Nokian, BFGoodrich, Michelin and the Chevrolet manual all ask for a monthly look. If one edge is wearing faster, ask a shop about alignment; if the pattern is patchy or cupped, ask about balance and suspension.

Each new season. Before the first cold spell, measure again. The winter figures the makers print (5/32 inch from Bridgestone, 5/32 to 6/32 from Nokian, 4 mm from Continental) are recommendations, and replacing before the season is the step the makers point to; decide it with a tire shop. Our best tires guide covers what to buy when you do.

Sources and documents

Every page below was read on 15 November 2026 and saved as text, except where the line says it was read on 5 November 2026. Marks: 🟢 federal or state text. Maker, trade body, club and magazine pages are named in words. Where a page carried no date, we say so by giving none.

  1. 🟢 49 CFR 571.139, Standard No. 139, new pneumatic radial tires for light vehicles (eCFR) (read 5 November 2026)
  2. 🟢 49 CFR 393.75, tires (eCFR) (read 5 November 2026)
  3. 🟢 RCW 46.37.425, Tires, unsafe (Washington State Legislature) (read 5 November 2026)
  4. 🟢 Utah Administrative Code R714-161-8, Tires and Wheels (Cornell LII) (read 5 November 2026)
  5. 🟢 67 Pa. Code § 175.80, Inspection procedure (Pennsylvania Code and Bulletin)
  6. 🟢 15 NYCRR § 79.21, Inspection of motor vehicles (Cornell LII)
  7. Bridgestone, How to check tire tread depth: the penny test (read 5 November 2026)
  8. Bridgestone, Maintenance and safety manual (PDF, January 2020) (read 5 November 2026)
  9. Bridgestone, How long a tire lasts (read 5 November 2026)
  10. Bridgestone Canada, Tire tread wear and causes
  11. Michelin, Tire tread depth: why it matters and how to measure it
  12. Michelin, Routine tire care tips
  13. Michelin Canada, How to interpret the tire wear indicator
  14. Michelin, When to replace tires (read 5 November 2026)
  15. Pirelli, How to check tire tread depth
  16. Continental, Tire tread
  17. Continental, Replacing tires (read 5 November 2026)
  18. Continental Canada, Winter tire markings
  19. Nokian Tyres, How to check tire tread
  20. Nokian Tyres, Tire wear patterns: how to read them
  21. Cooper Tire Canada, Tire tread
  22. BFGoodrich, How to inspect a tire
  23. Tires Plus, Tire tread depth
  24. Firestone Complete Auto Care, How to check tire tread depth with a penny
  25. Firestone Complete Auto Care, When do you need new tires (read 5 November 2026)
  26. Goodyear, news release, May 21, 2018
  27. Tire Industry Association, Tire replacement (read 5 November 2026)
  28. U.S. Tire Manufacturers Association (USTMA), Tire care and safety (read 5 November 2026)
  29. USTMA, Care and service of passenger and light truck tires (PDF) (read 5 November 2026)
  30. AAA, Tire study report (PDF, 2018) (read 5 November 2026)
  31. AAA Oregon/Idaho, Check your tire tread depth (read 5 November 2026)
  32. AAA Club Alliance, Tire wear and care, The Extra Mile (May 2024)
  33. Consumer Reports, Tire traction in wet weather: worn tires (read 5 November 2026)
  34. Modern Tire Dealer, Time to rethink tread depth? (April 8, 2026)
  35. Work Truck Online, Safe Tread Alliance introduces the quarter test (December 2, 2025)
  36. AME International, digital tread depth gauge listing
  37. Chevrolet, 2023 Equinox owner manual (read 5 November 2026)
  38. Toyota, Camry Hybrid owner's manual (read 5 November 2026)
  39. Nissan, 2023 Altima owner manual (read 5 November 2026)
  40. Hyundai, 2023 Elantra owner's manual (read 5 November 2026)
  41. Kia, Sportage 2023 online owner's manual, Tires and wheels (read 5 November 2026)
  42. Mazda, MX-5 Miata 2023 owner's manual (read 5 November 2026)
  43. Mazda, CX-5 2023 web manual, Replacing a tire (read 5 November 2026)
  44. Subaru, owner's manual (US edition, edited 2022/12/23) (read 5 November 2026)
  45. Volkswagen India, Tiguan owner's manual (edition 11.2021) (read 5 November 2026)
  46. PulsCar, home page

Prices verified 15 November 2026 on the pages they are carried from: this guide quotes no price of a tire or a gauge. Technical documents verified 5 to 15 November 2026 (each source's date is in the list above); links checked 15 November 2026. Written by PulsCar, which publishes this guide and sells no tread gauges or tires.