Trade articles say a converter is usually not the first thing that goes wrong, and no single sign proves it is bad. The signs the documents print are a check engine light with a converter code, lost power, a rattle, a rotten-egg smell, a failed emissions test, a hot or discolored shell and lower fuel economy. A 2010 CARS magazine article, which sets out a checklist from a Walker technical-assistance manager, says most converters fail because of a problem elsewhere in the emission system or the engine. The proof is a test: the stored codes, a check of misfires, leaks and sensors, then a restriction test or the maker's own procedure. Three signs mean stop before any of that (our advice, built on the makers' sentences quoted below). A flashing check engine light means an active misfire: pull over safely, switch the engine off and have the car towed; the only exception, a flashing light alone on a car that starts and runs normally, is a shop within 2-3 miles, reached gently, under 40 mph with light throttle. If you smell a scorching or pungent burning odor from the exhaust, or the converter is glowing or badly discolored, stop in a safe place away from grass and anything that can burn, switch the engine off, let it cool and have it checked before you drive it again. If you smell exhaust inside the car, open the windows fully, stop driving it as soon as it is safe and have it checked immediately; Mazda says not to drive it at all. Our advice if none of the three applies and the light is steady on a car that runs normally: get the stored codes read as soon as you can (Subaru and Toyota say immediately), and do not agree to a converter until a shop shows which test proved it.
This page answers one question: how to tell if a catalytic converter is bad, what else causes the same signs, and how a converter is tested. It links to our other pages instead of repeating them: the P0420 guide and P0430 guide for the codes and their routes, the P0420 statistics page for the federal complaint count, the sulfur smell guide for that smell, the replacement cost guide for prices (we print none) and the theft guide for a converter that has been cut off.
We do not test cars, and we say where the documents stop. The full text of thirteen owner's manuals was searched for what they print about the converter, the check engine light, heat and exhaust fumes (the list is under Sources; Jeep and Ram print many identical passages, and we count them as two). We also read four car-maker bulletins on catalyst diagnosis, the EPA's emissions-warranty fact sheet (October 2009, revised 2012, archived copy) and the federal rules behind it, a catalyst maker's page of signs, three VehicleServicePros articles (two with Eastern Catalytic material), a 2010 CARS magazine article quoting a Walker technical-assistance manager, and two pages by the repair-trade writer Larry Carley at AA1Car. In the text, 🟢 marks a government source and ⚪ a company, catalyst-maker or trade-magazine source; unmarked quotes are from car makers' own manuals and bulletins. No manual among the thirteen prints the words rotten egg, and none prints the word rattle about the converter. Advice that no source prints is labeled our advice.
Dangerous first: three things that mean stop
Our advice: signs other than the three below do not need a tow, but a steady light is not a reason to wait: Subaru and Toyota print "immediately," and Hyundai and Genesis warn of loss of engine power. Have the stored codes read as soon as you can. Three signs cannot wait at all. They are conditions the makers warn about, and they come before any diagnosis.
A flashing check engine light. Nine of the thirteen manuals print a statement about a flashing lamp, and every one treats it as a warning to act on. Jeep and Ram: "If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required." MINI: "Reduce the vehicle speed and have the vehicle checked immediately; otherwise, serious engine misfiring within a brief period can seriously damage emission control components, in particular the catalytic converter." Subaru: "If the light is blinking while driving, an engine misfire condition has been detected which may damage the emission control system." Their instructions differ. Chevrolet and Buick say to reduce speed, avoid hard accelerations and uphill grades, and find a safe place to park if the light continues to flash. Nissan says not to drive above 45 mph while it blinks and, once the light stops blinking and stays on, that you do not need to have the vehicle towed to the dealer. Our rule, in the box at the top of this page, is stricter than any of those sentences, and it is our advice, not a maker's. Our flashing light guide covers the misfire causes.
A converter that is too hot. All thirteen manuals warn that the hot exhaust can start a fire near flammable material; twelve name grass, leaves, paper or similar, and Toyota says flammable material. Jeep and Ram are the only manuals that say a malfunctioning converter itself runs hotter than normal. Nissan, Mazda and VW say an engine fault can make the converter overheat, and Subaru says the catalyst may overheat and burn if the engine is stopped while driving (see the table below): "A malfunctioning catalytic converter can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc." The same two manuals describe a warning smell (Ram's wording): "In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn off the engine and allow it to cool. Service, including a tune-up to manufacturer's specifications, should be obtained immediately." MagnaFlow ⚪ lists "glowing red" discoloration as "often an indicator of internal overheating." Our rule, drawn from those passages: If you smell a scorching or pungent burning odor from the exhaust, or the converter is glowing or badly discolored, stop in a safe place away from grass and anything that can burn, switch the engine off, let it cool and have it checked before you drive it again. Do not touch the exhaust; Hyundai says to keep away from the exhaust system and catalytic converter or you may get burned.
Exhaust smell inside the car. Exhaust contains carbon monoxide, which the National Library of Medicine's MedlinePlus 🟢 describes as a gas that has no odor or color and is very dangerous. A leak in the exhaust system is one way exhaust gets in; Buick and Chevrolet list it. Our rule, the same on our sulfur smell page: If you smell exhaust inside the car, open the windows fully, stop driving it as soon as it is safe and have it checked immediately; Mazda says not to drive it at all. A smell in the car is a reason to act on the smell, not to wait for a code.
The signs, and who prints each
The table lists each sign as a document prints it. A sign is a reason to get the car checked; it is not a diagnosis. The right-hand cell says who prints it. The sections after the table take each sign in turn, with what else can cause it.
The table lists what sources print, not how often each sign turns up; the documents give no counts, and we do not claim any. The signs also overlap. MagnaFlow, which sells converters, says so itself on its page: "these signs can overlap with other engine or exhaust system issues, so proper diagnosis done with an experienced professional is important."
Sign one: the check engine light and a converter code
The sign most sources put first is a light on the dashboard. MagnaFlow ⚪ says: "If you have a 1996-or-newer (OBDII) vehicle, a check engine light may indicate a problem with your catalytic converter." AA1Car ⚪ explains how the light gets there: the engine computer compares the oxygen sensors before and after the converter, and "if the converter is slow to respond, or the downstream O2 sensor readings don't flatten out and level off once the converter is hot and doing its thing, it will see that as a drop in operating efficiency and probably set a P0420 catalyst efficiency code." The 2010 CARS magazine article ⚪ reports that Joseph Bacarella, manager of technical assistance at Walker Exhaust Systems, says that even if a failed emissions test or trouble code indicates a problem, a technician needs to run preliminary tests before attention can be given to the converter. The article then says: "Most catalytic converters fail, or are unable to work efficiently, due to a problem occurring somewhere else in the emissions system and engine."
What the light means in an owner's manual is less specific than the trade pages, and it differs by maker. The table gives each manual's wording for a light that is on and steady. None of the thirteen ties a steady light to the converter by name except Hyundai and Genesis, which print the converter in the lamp text itself.
The makers do not agree on urgency, none prints a number of days, and each describes the lamp as an alarm about the emission system or the engine, not as a converter test. Toyota prints a first check: whether the fuel tank is empty or the fuel tank cap is loose, with the light going off after several driving trips if that was the cause. Our advice: a steady light on a car that runs normally is a reason to get the stored codes read as soon as you can (Subaru and Toyota say immediately), and to apply the flashing-light rule the moment it begins to flash.
What a catalyst code can and cannot say. AA1Car lists the family of codes the system can set for the converter itself: P0420 for catalyst system efficiency below threshold on bank 1, P0421 for the warm-up catalyst, P0422 for the main catalyst, P0423 for the heated catalyst, and the same group for bank 2 starting at P0430. A bank is a row of cylinders, and our P0420 guide explains which is which. The trade pages disagree on how much weight the code carries. AA1Car says: "The OBD II system is really good at detecting a failing or bad converter, so if everything else if working okay and there are no exhaust leaks or O2 sensor problems, and you get a P0420 code, chances are your vehicle needs a new converter." VehicleServicePros ⚪, in an article built on Eastern Catalytic material, says the opposite emphasis: "Although it typically points to a catalytic converter issue, it can just as easily be generated by a variety of engine problems not directly related to the converter." The two statements are compatible. Both say to rule out other causes first (AA1Car names exhaust leaks and oxygen sensor problems); they differ on how likely the converter is once that is done: AA1Car says "chances are" it needs replacing, VehicleServicePros says other engine problems can "just as easily" set the code. The documents give no count that settles it, and we do not claim one.
A code also only appears when the car's own test has run. AA1Car says the catalyst monitor "may run when the vehicle is cruising at a steady highway speed of 40 to 60 mph for at least 10 minutes with the engine at normal operating temperature and in Closed Loop," and will not run if there are oxygen sensor fault codes. Subaru's P0420 procedure spells out its own version for its cars: idle at least five minutes, drive at a constant 37 mph until the catalyst temperature reaches 500 degrees C (932 degrees F), then close the throttle for a fuel cut of at least five seconds. Chevrolet says a recently replaced or run-down 12-volt battery can leave the vehicle not ready for inspection. So no light does not prove a healthy converter on a car whose monitors have not run, and clearing the code erases the evidence; our reset guide explains why a cleared light comes back.
Our P0421 guide and the code index cover the other code families, and the code reader guide and diagnostic cost guide cover how to get the codes, the first piece of evidence.
Sign two: lost power, hard starting and stalling
A converter can fail by clogging instead of by wearing out, and the sign of a clogged one is the engine struggling to breathe. AA1Car describes it: "Driveability symptoms such as a drop in fuel economy, a loss of normal engine power, a rough idle or stalling immediately after starting the engine can all be signs of excessive backpressure caused by a plugged converter." ⚪ Its page on backpressure goes further: if the exhaust is completely blocked, the engine may start and idle fine for a minute or two and then die as backpressure builds. VehicleServicePros ⚪ says in its 2025 article that "A badly clogged converter can result in the engine dying shortly after startup." MagnaFlow ⚪ lists sluggish acceleration, and, as the most severe case, a hard-start or no-start condition in which exhaust restriction interferes directly with engine operation. Hyundai and Genesis say converter damage "could result in loss of engine power," and Jeep and Ram say a flashing lamp can precede "immediate loss of power or severe catalytic converter damage."
Two things follow. First, lost power does not say which part is restricted. AA1Car says not to jump to conclusions, because "it might be a collapsed pipe or muffler." A 2007 VehicleServicePros article ⚪ on backpressure (it carries a note that some information may no longer be relevant) says "Excessive backpressure often mimics late valve timing, and has fooled more than one technician into replacing a timing chain or belt." Second, power loss has plenty of causes that never touch the exhaust, and our uphill power guide, hesitation guide, no-acceleration guide and stalling guide cover those.
Our advice, where no source prints it: a car that loses power as you drive, or that starts and then stalls, is a car to stop driving in traffic and have looked at, because a stall in an intersection is its own danger. If the light is also flashing, the flashing-light rule above applies first.
Sign three: a rattle from under the car
A rattle is one of the signs the trade pages and a Toyota bulletin print, and the documents are thin here. Inside the converter, a ceramic honeycomb sits in a metal shell. VehicleServicePros ⚪ prints a photo caption (images courtesy of Eastern Catalytic) saying that road damage involving impacts can easily dislodge and damage the ceramic bricks. AA1Car says, of a converter you have removed: "You can also shake the converter. If you hear stuff rattling around inside, it means the honeycomb substrate is probably damaged, cracked or crumbling and falling apart." AA1Car's page on backpressure says of a car with a restriction: "You can thunk the converter to see if it rattles inside (indicating the catalyst substrate is broken)."
The one car maker document we read that prints a rattle is Toyota's bulletin T-SB-0161-13, dated 31 October 2013. It describes "Some 2010 model year Tacoma vehicles equipped with the 2TR-FE engine" that "may exhibit a front exhaust pipe catalyst rattle noise and/or MIL 'ON' condition with DTC P0420." Its procedure shows how this maker tests for a rattle on that truck: test-drive and verify an abnormal rattle while accelerating, raise the vehicle on a hoist "with the engine running," increase the engine speed and listen to the catalytic converter section of the front exhaust pipe assembly, with the caution "Avoid contacting any part of the exhaust system – it is VERY HOT." If the noise is loudest at the converter section, replace the front exhaust pipe assembly; if not, "This bulletin does NOT apply. Continue diagnosis using the applicable Repair Manual." The repair is covered, the bulletin says, under the Toyota Federal Emission Warranty, in effect for 96 months or 80,000 miles, whichever occurs first, from the vehicle's in-service date. It applies to those trucks only and is not a general test.
What none of the thirteen manuals prints is the word rattle about the converter or the exhaust. What eight of them print is a statement about a change in exhaust sound: six as an instruction to have the exhaust checked (Genesis, Hyundai, Jeep, Nissan, Ram, Toyota), Buick and Chevrolet as a condition under which exhaust may enter the vehicle. Hyundai: "If you hear a change in the sound of the exhaust or if you drive over something that strikes the underneath side of the vehicle, have the exhaust system checked as soon as possible by an authorized HYUNDAI dealer." Toyota lists "abnormal exhaust noise" with holes, cracks and damaged joints as a reason to have the exhaust inspected and repaired. Subaru calls a crackling from the exhaust for a short time after shut-off normal.
Our P0420 guide suggests tapping the cold shell of the converter and telling a loose rattle inside the shell from a tinny buzz in the outer skin, which is a loose heat shield. That is a hands-on check from that guide, not a method printed in any maker document we read for this page, and no source we read prints the heat shield part. Our advice follows from the Toyota caution above: do any tapping with the engine off and the exhaust cold, listen to a running engine only from beside the car, parked outdoors, never from underneath, and leave any test under a running car to a shop with a hoist. A rattle also does not tell you whether the converter is the cause or the victim: a failed converter may have been killed by a misfire that is still going on.
Sign four: a rotten-egg or sulfur smell
This is the sign on which the documents disagree most. MagnaFlow ⚪ lists a sulfur smell: "If you smell rotten eggs when your vehicle is running, then the catalytic converter may not be catalyzing the sulfur in the exhaust gas." VehicleServicePros ⚪, in its 2025 article, says: "Converter-related issues can present themselves by a sulfur smell when the engine warms up to operating temperature, poor acceleration, abnormal fuel mileage, misfires, etc." Neither prints a test that separates a bad converter from a healthy one that smells.
The car makers say less. In the full text of all thirteen manuals, none prints the words rotten egg. Two print something about sulfur and odor, and neither ties it to a failing part: Mercedes-Benz says that fuel that is not sufficiently low in sulfur can produce unpleasant odors, and the Volkswagen manual we read, the India edition, says of its diesel exhaust treatment that the emissions may have a sulphur-like smell even if the system is working properly. Jeep and Ram print a different odor, a scorching or pungent burning smell, and tie it to catalyst overheating, which is covered in the first section.
Our sulfur smell guide reads the research behind the exhaust version of this smell, and it is the page to open if the smell is your main sign. One point from it belongs here: the documents it reads describe sulfur that the catalyst stores from fuel and can release when hot, which a healthy converter can do too, and it lists four other sources of the smell that have nothing to do with the exhaust, two of them dangerous. Our advice: a rotten-egg smell on its own is a reason to check where it is strongest, apply the rules on that page, and get the codes read. It is not by itself a reason to buy a converter.
Three quieter signs: a failed test, a discolored shell and fuel economy
A failed emissions test. MagnaFlow ⚪ writes that a failing converter "may be unable to reduce emissions to legally acceptable levels, resulting in a failed inspection." On a newer car the test and the light travel together: AA1Car says "A vehicle with an illuminated Check Engine Light and ANY trouble codes will NOT pass an emissions check." The EPA fact sheet 🟢 gives a test failure a second role, as the trigger for the federal performance warranty (below). A test result decides nothing about which part failed. Our P0420 guide covers the federal inspection rule and why clearing a code just before a test fails, and our inspection cost guide covers the test itself.
A hot, discolored or warped shell. MagnaFlow ⚪ lists "Exterior Discoloration" and says excessive heat can cause visible discoloration, such as a glowing red color, "often an indicator of internal overheating." AA1Car says "Another clue that the converter may be running too hot is a badly discolored or warped converter shell." VehicleServicePros ⚪ says that if the converter case shows a bluish coloration, this is a sign that the converter has experienced excessive heat levels. These are signs an inspector sees under a car, and they fit the Jeep and Ram warnings above.
Lower fuel economy. MagnaFlow ⚪ says: "Poor flow in the exhaust system can cause the engine to strain itself, increasing fuel consumption and non-optimal performance." AA1Car and the 2007 VehicleServicePros article list poor fuel economy among the symptoms of excess backpressure. None of the documents puts a number on how much worse economy a restricted converter causes, and we do not claim one.
What else causes the same signs
The most important section of this page is the one that says why the signs prove less than they seem to. The trade sources say the converter is usually where trouble ends up, not where it starts, and the car makers print that engine faults can damage it.
The strongest wording is from the trade. VehicleServicePros ⚪, in its 2013 article built on Eastern Catalytic material, says: "Yes, a converter can fail, but more often than not, the root cause might involve upstream components such as an O2 sensor, fuel injectors, spark plugs, EGR valve system, exhausts manifolds, vacuum hoses and MAF sensors." The same article lists nine causes under the heading "Possible 'non-converter related' P0420 causes", among them intake manifold leaks, fuel injector leakage, wrong spark plugs, incorrect ignition timing, an EGR problem, oil or antifreeze entering the exhaust, an oxygen sensor malfunction, road damage and silicone contamination. AA1Car ⚪ says: "converters don't just foul or plug up for no good reason. There is always an underlying cause which must be diagnosed and corrected before the problem can be eliminated." It adds that a single misfiring spark plug can cause an increase in hydrocarbon emissions of 2,500 or more parts per million, which can push the converter's operating temperature well above its normal range. The 2010 CARS ⚪ article, following Walker's Bacarella, lists what a technician checks first: the service history, other trouble codes, exhaust leaks, whether the converter has lit off, backpressure, the oxygen sensors, the cooling and fuel systems, cylinder balance and volumetric efficiency, and sometimes a software re-flash.
Three car-maker documents show an order of work that looks for other causes first, though Kia's covers only misfire.
Subaru, bulletin 09-110-23R, a P0420 diagnostic procedure for 2017-2023 models. The steps run: a general inspection; a fault scan for misfire codes (P0300-P0304), fuel-trim codes (P0171, P0172) and oxygen and air-fuel sensor codes; a check of the oil level and a pulse of the throttle while watching the tailpipe for white smoke; an inspection for leaks, loose hardware or damage at the cylinder heads, front exhaust pipe, converter and sensors; an active test of the air-fuel sensor; a road test and a read of the catalyst deterioration value; a check of the exhaust gas recirculation piping; and a check of the rear oxygen sensor's harness and waveform. The bulletin has the front and center exhaust pipes replaced at only three points: after an engine repair when white smoke was seen (Step 3), when the air-fuel sensor active test passes (Step 5), or when the second road test misses its value (Step 7); a failing air-fuel sensor is replaced instead. Our P0420 guide follows the bulletin through the routes.
GM, preliminary information PIP5110B, July 2015. For 2011-2015 Chevrolet Silverado HD, GMC Sierra HD and related vans with a P0420 and no other code, it tells the technician to check for a possible leak in the exhaust system behind the bank 1 sensor 2 oxygen sensor, to install a new clamp if one is found, and says: "This repair must be attempted before considering the replacement of a catalytic convertor." The bulletin is for those trucks only.
Kia, subsequent repair action SC176Y, revised 23 March 2026. For 2012-2016 Soul models with the 1.6-liter engine it prints a flowchart in which a P0420 with an active P030X misfire code sends the technician to an engine compression check, and a failed check to an engine replacement (the bulletin's claim line for that path also lists the converter). The bulletin's printed condition is "catalyst system efficiency deterioration or a malfunction indicator lamp illumination with an active, history or pending P0420 with or without a P030X misfire DTC." Without an active misfire code, or if every cylinder passes, the same flowchart replaces the converter at no charge, and it applies only to cars that already had recall SC176 done. Our Kia Soul guide covers the recall.
The car makers' manuals add the other half of the list, what an engine fault or a driver's habits can do to a converter. The table collects the sentences. A cell shows a short version; the quotes are in the sources.
Ten of the thirteen manuals print a sentence that ties misfiring, an engine malfunction or unburned fuel to converter damage or overheating: Genesis, Hyundai, Jeep, Mazda, Mercedes-Benz, MINI, Nissan, Ram, Subaru and Volkswagen. Buick, Chevrolet and Toyota do not. Jeep and Ram add that the converter will not require maintenance under normal operating conditions, but that, in Jeep's words, "it is important to keep the engine properly tuned to ensure proper catalyst operation and prevent possible catalyst damage" (Ram's sentence says "assure"). Not one manual lists a converter replacement interval. That is a statement about thirteen manuals and the text we searched; yours may differ.
For a reader this is the rule that protects money. AA1Car says "replacing a bad converter will only solve the current problem temporarily" if the underlying cause is not repaired. VehicleServicePros ⚪ adds, about failures caused by those upstream problems: "Failures caused by these problems are not covered by the manufacturer's warranty." Whether a failure falls under the EPA's denial reasons (see the warranty section) depends on the claim. Our pages on lean and rich codes, misfires, oxygen sensor cost, smoke from the exhaust (black, blue and white), running rough and spark plug cost cover the causes the trade sources list.
How a shop tests a converter: the printed methods
The CARS article's Walker checklist and Subaru's bulletin follow a similar order: the stored codes and the history, then the causes upstream of the converter. They differ after that: the CARS article puts direct converter tests last, while Subaru's flow replaces the front and center pipes at three branches (Steps 3, 5 and 7) and reads the catalyst deterioration value after the road tests (Steps 6 and 7). This section lists the tests as the documents print them, with their numbers side by side. We do not average the numbers or pick a winner, and we do not claim any of them is the one your shop uses.
The maker's own procedure. Subaru's bulletin 09-110-23R, described above, is the only maker procedure we read that tests catalyst efficiency itself, and it is built for Subaru's scan tool: it reads a catalyst deterioration value after a prescribed road test and compares it with a table that differs by model and engine. Toyota's bulletin T-SB-0161-13 is a listening test on one truck with the engine running on a hoist. GM's PIP5110B is a check for one kind of exhaust leak, and Kia's SC176Y is a repair flowchart for one Soul engine after a recall. None of the four is a general test, or one a driver can run in a driveway.
Sensor waveforms and the oxygen storage test. The CARS article ⚪ describes two tests that a scan tool and a technician can run. Russell Rockstad, a certified smog instructor at Universal Technical Institute: "When the catalytic converter is working properly, the rear oxygen sensor will be working somewhere above 450 and 500 mV, and pretty much stays steady." Bacarella says many OBD II systems have moved to an oxygen storage capacity test: the computer forces a rich condition to empty the converter of stored oxygen, then a lean condition, and measures how long the rear sensor takes to register it, with a cut-off at two seconds: "if you have two seconds of oxygen storage capacity it typically means the catalytic converter has enough capacity to do its job properly."
The gas tests. Rockstad calls a carbon dioxide cranking test the most popular. The vehicle runs at 2,500 rpm for three minutes, the ignition is then disabled, the engine is cranked for 10 seconds, and a five-gas analyzer checks whether carbon dioxide goes above 12.5 percent; less, or hydrocarbons above 500 parts per million, means the converter is weak. AA1Car ⚪ adds that "There is no way for a do-it-yourselfer to easily check converter efficiency," and that most shops don't use exhaust analyzers much anymore, relying on the car's own catalyst monitor instead.
The restriction tests: vacuum and backpressure. These test whether the exhaust flows, which can point to a plugged converter or to another restriction in the exhaust. The numbers differ by source, and the table puts them side by side.
Read the table as a range of opinions: the idle figures are close but not the same, AA1Car's converter page gives a different speed (2,500 rpm) from the others (2,000), and the 2007 article calls a single fixed number somewhat unrealistic. A direct reading is taken through the oxygen sensor port or a tapped pipe ahead of the converter. To tell the converter from the rest of the exhaust, AA1Car says to disconnect the exhaust pipe behind the converter and read again: "No change in backpressure would indicate a blockage at or ahead of the converter. If backpressure drops back to normal, the problem is not the converter but a collapsed pipe or muffler."
The cheaper cousin is an intake vacuum gauge, which reads the engine's breathing without opening the exhaust, and the recipes differ again. AA1Car's converter page: normal idle vacuum for most engines is 18 to 22 inches Hg (its backpressure page says 16 to 22), and a reading "10 percent lower than normal and/or continues to drop as the engine runs" probably indicates a buildup of backpressure. VehicleServicePros 2013: hold 3,000 rpm and the needle should rise and level off; if it starts to drop, pressure may be backing up. MagnaFlow ⚪, for a car with no check engine light or built before 1996: at 2,500 rpm, a gauge that does not return to a similar reading, or is very slow to do so, means a failing converter may be a contributing factor. AA1Car and the 2007 VehicleServicePros article print a caveat with the vacuum test; AA1Car: "Remember, though, that intake vacuum can also be affected by retarded ignition timing and valve timing." The 2013 and 2025 VehicleServicePros articles, MagnaFlow and the CARS article print the test without it. AA1Car and the VehicleServicePros articles read a falling vacuum as an exhaust restriction, not the converter by name; MagnaFlow words it as a failing converter that may be a contributing factor.
The temperature test, where the sources contradict each other. MagnaFlow puts an infrared thermometer in its at-home tests, and the documents split on it.
AA1Car and VehicleServicePros agree that the difference across a good modern converter can be small (about 30 and 50 degrees F at 2,500 rpm). MagnaFlow gives "typically 100°F or more" without an engine speed. VehicleServicePros 2013 calls 100 degrees F the old rule of thumb. AA1Car and MagnaFlow do agree on one point: a large gap between the front and the back pipe can mean trouble, though not the same trouble. AA1Car says a difference of 200 degrees F or more means unburned fuel is getting into the exhaust and causing the converter to overheat, with a misfiring plug, a bad ignition coil or a leaky exhaust valve the most likely causes, so a hot converter can be a sign of an engine problem, not a converter fault. We do not pick between them. Our advice: a driveway infrared reading is a weak basis for buying or refusing a converter on its own.
Scan-tool checks of the engine's own data. AA1Car lists readings that can point to a restricted converter: a significant fuel-trim difference between the two banks of a V6, V8 or V10, and lower than normal barometric pressure, manifold pressure or calculated load values. VehicleServicePros 2025 says fuel trims "can provide an overall picture of what is causing the problem." AA1Car calls these several ways to detect a restricted, plugged or worn out converter with a scan tool, and says a catalyst efficiency reading of 90 percent or less would tell you the converter is bad. Our reading: a technician takes them together with the causes upstream, and none replaces the restriction tests above.
What you can do yourself, and what the sources say needs a shop
MagnaFlow ⚪ has a section headed "At-Home Diagnosis" with two preliminary tests, the infrared temperature check and the vacuum gauge test above, and adds: "If you don't have the tools or the inclination, then an auto repair/muffler shop, dealer or mechanic can perform these tests for you." The page belongs to a company that sells converters, and the temperature test it prints is one that AA1Car and VehicleServicePros question for modern cars; MagnaFlow itself says a professional diagnosis is important. Most other tests above need a shop or special tools, and the printed cautions matter as much as the steps:
- Toyota's test needs the car on a hoist with the engine running, and warns "Avoid contacting any part of the exhaust system – it is VERY HOT."
- AA1Car says, of tapping into the exhaust for a pressure gauge, "never drill a hole into the converter itself!" and that a hole drilled ahead of the converter has to be plugged afterwards. The 2007 article says "Never pierce a hole in the converter or muffler housing."
- Our advice: do any engine-running test outdoors or with the exhaust vented out of the building. Mazda's manual says: "Do not run the engine when inside an enclosed area: Running the engine inside an enclosed area, such as a garage, is dangerous."
Our advice is short. A driver can safely get the stored codes and any freeze frame read before anyone clears them, listen for a change in the exhaust from beside the car, parked outdoors, and write down when each sign happens (cold start, hot, under load, uphill). Anything that needs a hoist, a hot exhaust, a drilled pipe or a gas analyzer is a shop job. If a shop proposes a converter, ask which of the tests above showed it, and ask for the reading in writing.
The federal emissions warranty
The warranty is the reason to ask that question before paying. The EPA's fact sheet on emissions warranties 🟢 (EPA-420-F-09-048, October 2009, revised September 2012; we read it on the EPA's archived-site copy) says that for 1995 and newer light-duty vehicles, "Specified major emission control components are covered for the first 8 years or 80,000 miles of vehicle use (whichever first occurs)." It names three: catalytic converters, the electronic emissions control unit and the onboard emissions diagnostic device. The same terms are in the law, 42 U.S.C. 7541(i)(2) 🟢, which says the warranty period for a specified major emission control component "shall be 8 years or 80,000 miles of use (whichever first occurs)" and defines the term as "only a catalytic converter, an electronic emissions control unit, and an onboard emissions diagnostic device" (the Administrator may designate others), and in the federal regulation 40 CFR 85.2103 🟢, which lists catalytic converters and SCR catalysts among them. Three further statements from the fact sheet matter for a reader:
- "According to federal law, an emission control or emission related part, or a specified major emission control component, that fails because of a defect in materials or workmanship, must be repaired or replaced by the vehicle manufacturer free of charge as long as the vehicle has not exceeded the warranty time or mileage limitations for the failed part."
- With a valid claim you cannot be charged for the diagnosis or the pipes, brackets, adjustments or labor needed to complete the repair.
- The warranties apply to used vehicles, but to have the manufacturer pay you must take the vehicle to a facility it authorizes.
The fact sheet also says a manufacturer inside the limits can deny a claim only if evidence shows the owner failed to properly maintain and use the vehicle, and gives three examples: abuse such as off-road driving or overloading, tampering with emission control parts, and improper maintenance.
Two points where the documents differ or stop. When the clock starts: 40 CFR 85.2103(b) 🟢 says the warranty period "begins on the date the vehicle is delivered to its ultimate purchaser or, if the vehicle is first placed in service as a “demonstrator” or “company” car prior to delivery, on the date it is first placed in service." Toyota's T-SB-0161-13 counts from "the vehicle's in-service date," which fits that rule; AA1Car ⚪ says coverage runs from the vehicle's build date, which the regulation does not say. The EPA fact sheet does not state a start date and points to the owner's manual or warranty booklet, so use the booklet. And the manuals: none of the thirteen we searched prints the 8-year, 80,000-mile term. Nine (Genesis, Hyundai, Jeep, Mazda, MINI, Nissan, Ram, Subaru and Toyota) name the emission warranties or point to a separate booklet; Buick and Chevrolet name a Federal Emission warranty only in courtesy-transportation text; Mercedes-Benz and Volkswagen print nothing on it. California and some other states add their own terms, which our P0420 guide covers together with the recalls and extended coverages that can pay for a converter. Our P0420 statistics page counts 302 federal complaints that name P0420 and shows how those reports sit against the warranty clock.
What it costs, and what a quote should show
We print no price. A converter, a sensor, an exhaust repair and a diagnostic are different jobs with different prices, and our catalytic converter replacement cost guide carries the dated figures, while our diagnostic cost guide covers what a test should cost and our most expensive codes page shows where converter codes sit. Instead, here is what the documents say a quote or an invoice should settle, as a checklist for the conversation:
- Which test showed the converter? A code alone is not a test: VehicleServicePros ⚪ says P0420 "can just as easily be generated by a variety of engine problems not directly related to the converter."
- What was ruled out? Misfires, leaks and sensors, in the order Subaru and the CARS article's Walker checklist print; that checklist ends with a possible software re-flash.
- Is the car inside the warranty or a recall? The EPA fact sheet 🟢 says that to have the manufacturer pay, you must take the vehicle to a facility it authorizes, inside the warranty period.
- What goes in? AA1Car ⚪ says "it is illegal to replace it with a straight pipe," and an EPA exhaust-repair fact sheet 🟢 says that under federal law "catalytic converters may not be removed and replaced with "converter replacement pipes" by any person." AA1Car recommends replacing the oxygen sensors at the same time; that is the page's advice, and our oxygen sensor cost guide covers it.
- What was done about the cause? AA1Car: "Identifying a plugged or fouled catalytic converter is only half the fix."
If the converter is the cause and the car has been stolen from, not worn out, our theft guide covers that case.
Three traps that cost owners money or safety
Trap one: buying a converter on a code alone. The code says the computer judged the catalyst below its threshold. VehicleServicePros ⚪ lists nine causes it labels 'non-converter related', Subaru's bulletin puts a general inspection and the misfire and sensor code check first and, apart from the white-smoke branch after an engine repair, the leak and sensor steps before the pipe replacement, and GM's bulletin says a leak repair must be attempted before a converter is considered. AA1Car says that if the cause is not repaired, sooner or later the new converter will likely suffer the same fate. The protective question for the shop is which test showed the converter, and which causes were ruled out. Our P0420 guide has the script for that conversation.
Trap two: reading a weak test as proof. A driveway infrared reading or a vacuum gauge needle each shows something, and each is disputed or limited in the documents; the tap on the cold shell is our P0420 guide's own suggestion, not a printed test. MagnaFlow prints a 100 degrees F rule that two trade sources say may not be an accurate way to judge a modern converter; the vacuum test is limited by ignition and valve timing, as AA1Car and the 2007 VehicleServicePros article say; and AA1Car says there is no way for a do-it-yourselfer to easily check converter efficiency. Our advice: treat a home reading as a reason to see a shop, and treat a shop's reading as a number to see in writing.
Trap three: driving on a warning that the makers call urgent. Jeep and Ram say a flashing light means severe converter damage and power loss will soon occur, and that a malfunctioning converter can start a fire if you drive slowly or park over dry plants. The rules at the top of the page apply before any diagnosis.
Two typical situations
These are composite scenarios, not individual customers. Each is built only from statements printed above.
A steady light on a car that runs normally. The reader finds a P0420 with no other code. The first moves are the ones the documents list: a check for leaks behind the rear oxygen sensor and for the sensor itself (GM PIP5110B, Subaru), and a look at the warranty and at recalls or bulletins for the VIN. Our advice adds saving all stored codes and the freeze frame before anyone clears them, and getting the car checked as soon as you can (Subaru and Toyota say immediately); the flashing-light rule applies if the light starts to flash.
A car that loses power uphill and rattles from underneath, out of warranty. The signs match a restricted or broken converter, and a collapsed pipe or muffler. The shop's job is a restriction test: a backpressure reading ahead of the converter and another after it. The reader asks for the readings and for the rattle to be located, as Toyota's bulletin prints a listening test with the engine running on a hoist, and asks what caused any failure before agreeing to a part.
Where PulsCar's free sound check fits, and where it does not
This section is about our own product; what the free check does is described on the PulsCar homepage ⚪. There are no affiliate links on this page.
Should you record your engine with PulsCar's free check if you think the converter rattles? Only after the stop rules above. A flashing light, a scorching odor from the exhaust and exhaust smell inside the car come first, and none of them is a reason to record anything. PulsCar's free check takes a 30-second video of the engine running and is a screening from sound, not a hands-on inspection; its homepage lists exhaust among the systems it reports on, and says a clip that cannot support a verdict is reported as inconclusive. It cannot read your codes, take a backpressure or temperature reading, smell, or say that a converter is bad, and it cannot say whether a rattle is the converter, a heat shield or a pipe. The shop still needs a test.
Can the signs tell me what is wrong, and where does PulsCar's guide stop? The signs point to a short list: the converter itself, or a misfire, leak, sensor, fuel or software cause upstream. This PulsCar guide searches thirteen owner's manuals, four car-maker bulletins, an EPA fact sheet and federal rules, and trade sources, and it can tell you what each document prints about each sign and each test. It cannot see your car or tell how often each cause occurs, because the documents give no counts, and it cannot say that any one test is the one your shop will use. If your own owner's manual or warranty booklet says anything stricter, believe it, and tell the shop about every warning light that came with the sign. Treat the signs as reasons to test, not as a diagnosis.
What does a bad converter cost to fix, and does PulsCar sell the repair? PulsCar's free check is not a repair, and no link on this page is an affiliate link. The price follows the cause, from a clamp or a sensor to a converter, and our cost guides carry the dated figures. Ask the shop for the stored codes, the test that showed the converter and the warranty position in writing before you agree to a part, and treat any figure you read as a range from a guide, not as a quote for your car. If the quote says converter, ask which test in this guide showed it and whether the car is still inside the emissions warranty. The flashing check engine light rule at the top of the page applies if a light is flashing.
What this page cannot tell you
- Which part is bad on your car. The documents give no counts of how often each cause turns up, only phrases such as "more often than not." Your car and a test decide.
- A number that settles the backpressure or temperature question. The sources give different numbers, and one calls a single fixed number somewhat unrealistic. We show them side by side and do not average them.
- How today's cars behave. AA1Car's pages are undated, two trade articles are from 2007 and 2010, and the EPA fact sheet is from 2009.
- What your own manual says. We searched thirteen manuals, one model each. Honda, Ford, Lexus, Volvo, Tesla, the BMW brand, Volkswagen's U.S. manual and Mitsubishi were blocked or not available to read, and the Volkswagen manual we read is the India edition. Your manual and warranty booklet govern your car.
- That a rattle, a smell or a code means a failed converter. No manual among the thirteen ties a rotten-egg smell or a rattle to a failed converter (Jeep and Ram tie only a scorching odor to severe catalyst overheating); one catalyst maker and one trade source tie the smell to it, and AA1Car, VehicleServicePros and one Toyota bulletin tie a rattle to it (the two trade sources as a sign of a damaged substrate, Toyota on one truck).
- Whether it is safe to drive your car. A page cannot see or smell the car. The three rules at the top are the ones we do not bend.
Your action plan: now, this week, this month
Now (ten minutes, car parked outdoors). Everything in this plan is our advice, built on the sources above; maker sentences are marked. Which sign, and when does it happen? Our advice: a flashing check engine light means an active misfire: pull over safely, switch the engine off and have the car towed; the only exception, a flashing light alone on a car that starts and runs normally, is a shop within 2-3 miles, reached gently, under 40 mph with light throttle. If you smell a scorching or pungent burning odor from the exhaust, or the converter is glowing or badly discolored, stop in a safe place away from grass and anything that can burn, switch the engine off, let it cool and have it checked before you drive it again. If you smell exhaust inside the car, open the windows fully, stop driving it as soon as it is safe and have it checked immediately; Mazda says not to drive it at all. If the car loses power as you drive, pull over safely and have it looked at; Nissan says not to keep driving with a noticeable loss of performance. Do not touch the exhaust, and do not run the engine in a closed garage.
This week. If none of those applies, get the stored codes and freeze frame read and saved, and write down when each sign happens. Our code reader guide and diagnostic cost guide show how. Find the warranty booklet and the in-service date, and ask a dealer or the maker's recall lookup to check the VIN for recalls. If the light is steady and the car runs normally, do not leave it to the end of the week: book the check as soon as you can; Subaru and Toyota say immediately. If the car may still be inside 8 years or 80,000 miles, start with a dealer for your brand, because the EPA fact sheet says that for the manufacturer to pay, the car goes to a facility it authorizes; outside the warranty, a general repair or exhaust shop can run the restriction tests, so ask whether it has a backpressure gauge.
This month. Ask any shop that proposes a converter which test showed it and what was ruled out, and ask for the readings in writing. Read our P0420 guide and replacement cost guide before you agree to a part. If the converter is missing, our theft guide covers that case, and our dashboard warning light guide and check engine light guide cover the lights that come with these signs.
Sources and documents
All sources were read on 15 November 2026 unless a different date is given. Manuals are the manufacturers' own owner's manuals; the first eight were downloaded on 11 November 2026 and the other five on 15 November 2026. Government text is marked 🟢 and company, catalyst-maker or trade-magazine statements ⚪ in the body.
- Chevrolet Equinox 2026 Owner Manual (GM part 18951079 B, June 2025). PDF · Hyundai Elantra 2023 Owner's Manual. PDF · Nissan Rogue 2026 Owner's Manual. PDF · Subaru owner's manual MSA5M2403A. PDF · Mazda MX-5 Miata 2023 Owner's Manual. PDF · Toyota Camry Hybrid Owner's Manual OM06261U. PDF · Mercedes-Benz C-Class Sedan 2022 Operator's Manual. PDF · Volkswagen Tiguan User Manual, India edition, November 2021. PDF
- Jeep Compass 2023 Owner's Manual (Mopar 5662345). PDF · Ram 1500 2023 Owner's Manual (Mopar 5690659). PDF · Genesis G70 2022 Owner's Manual. PDF · Buick Envision 2025 Owner Manual (GM 18321629 B). PDF · MINI Clubman (F54) Owner's Manual, model year 2024. PDF
- Subaru Service Information Bulletin 09-110-23R, "DTC P0420 Diagnostic Procedure," 9 October 2023, revised 7 November 2023. PDF · Toyota T-SB-0161-13, "Front Exhaust Pipe Catalyst Rattle Noise and/or MIL ON DTC P0420," 31 October 2013. PDF · GM preliminary information PIP5110B, "SES Lamp P0420," July 2015. PDF · Kia SC176Y, subsequent repair action, revision 1, 23 March 2026. PDF
- EPA, Emissions Warranties for 1995 and Newer Cars and Trucks, EPA-420-F-09-048, October 2009, revised September 2012 (EPA archived-site copy). PDF 🟢 · 42 U.S.C. 7541, Compliance by vehicles and engines in actual use. Text 🟢 · 40 CFR 85.2103, Emission warranty. Text 🟢 · EPA, fact sheet on exhaust system repair (undated PDF, read 4 November 2026). PDF 🟢 · National Library of Medicine, MedlinePlus, Carbon Monoxide Poisoning. Page 🟢
- MagnaFlow, Symptoms of a Bad Catalytic Converter, 1 January 2026. Page ⚪
- Mike Mavrigian, VehicleServicePros, Catalytic converter diagnosis, 7 August 2013 (with Eastern Catalytic). Page ⚪ · Mike Mavrigian, VehicleServicePros, What's really wrong when a catalytic converter 'fails', 6 June 2025. Page ⚪ · VehicleServicePros staff, Exhaust backpressure checks are essential, 1 March 2007. Page ⚪
- Larry Carley, AA1Car, What You Should Know About Catalytic Converters (undated). Page ⚪ · Larry Carley, AA1Car, How Exhaust Backpressure Affects Your Engine (undated). Page ⚪
- CARS magazine, Nothing lasts forever, 30 April 2010, on Auto Service World. Page ⚪
- PulsCar homepage. Page ⚪
What we could not read: owner's manuals of Honda (the maker's technical site returned a service error), Ford, Lexus, Volvo, Tesla, the BMW brand, Volkswagen (U.S.) and Mitsubishi; Walker's own technical pages (not found) and Eastern Catalytic's own site (no answer); Brake & Front End and Tire Review articles on converter diagnosis, NAPA's and O'Reilly's pages on symptoms (access errors); and the CDC's carbon monoxide pages (access errors). None was bypassed.
Prices verified: this page prints no prices; the cost guides it links to carry their own verification dates.
Technical documents verified November 2026.

