🚨 60-Second Triage — Smell of liquid gasoline, a wet patch or drips under the car: that is a fuel leak, not a vapor code. Our advice, not a maker's: do not drive it, keep flames and sparks away, leave it outdoors and have it towed. Flashing check engine light, or a red warning light: stop in a safe place and follow your manual (full rule in the drive section below). Steady light, car drives normally, code reads P1456 on a Honda or Acura: our advice, based on Honda's step 2: take the fuel cap off, look at its seal and at the threads and sealing surface of the filler neck, and refit it until it clicks (Honda's bulletin says three clicks for the cap it describes). Not a Honda or Acura: P1456 is a maker's own code and can mean something different on another make, so find your maker's wording before buying anything.
📊 What P1456 means — Honda and Acura, model years 1996 to 2006: a leak on the fuel tank side of the vapor system, as the two service bulletins we read define it; first check, the gas cap · Any other make: a maker's own code that can mean something else, so ask for your maker's wording · Cost: no price is printed here; the cost section shows what drives a quote.
P1456 is not a standard code. It sits in the block of numbers that each carmaker defines for itself, and Honda and Acura print it, in the bulletins we read, as a leak in the fuel tank side of the fuel vapor system. If your car is a Honda or Acura from the late 1990s or the 2000s, this page can tell you what the maker's technicians are told to do, in order. If it is another make, no document we read establishes what the code means, and the page shows how to find that maker's wording and what the manuals we read say about the parts that matter: the gas cap, the light and the vapor system.
Honda's own bulletin opens with the sentence that defines the job: "This bulletin updates the troubleshooting procedures for DTC P1456 (EVAP control system leakage [Fuel tank system]) and DTC P1457 (EVAP control system leakage[EVAP canister system])." Everything after it is a test sequence. It starts with a voltage reading on Honda's scan tool, and its first tool-free step is to look at the fuel cap.
By the end of this guide you will know which of five routes your P1456 belongs to, what proves it, and what a quote should name. Claims marked 🟢 rest on a document in Sources, opened and read on 20 November 2026. This guide prints no repair prices, because no price page for this repair could be read that day; where cost matters it points to the cost guides instead.
What P1456 is, and why it is not a standard code
A trouble code is a short label the car's computer stores when a self-test fails. Codes that start with P0 are defined by the industry standard and mean the same on every make. Codes that start with P1 are different: they are the manufacturer's own.
California's on-board diagnostics rule, 13 CCR 1968.2, says it in the language of regulation: manufacturers "shall use appropriate SAE-defined fault codes of SAE J2012 (e.g., P0xxx, P2xxx) whenever possible," and "With Executive Officer approval, manufacturers may use manufacturer-defined fault codes in accordance with SAE J2012 specifications (e.g., P1xxx)." The rule text we read is the current version, written long after these cars were built, so it describes what a P1 code is, not what Honda decided in 1999. EPA's December 2003 paper on OBD (EPA420-F-03-042) adds a fact for cars of that era: federal rules asked the vapor system test to detect an orifice of 0.040 inch, California's 0.020 inch.
The practical consequence. A generic code reader may print one label for P1456 whatever the car. The label can be right for one make and wrong for another. Before you act on it, find the wording in your own maker's documents. For Honda and Acura we could read it. For others we could not, and the sections below say which.
Which makers print P1456, and what we could read
We looked for the code in the makers' own documents: service bulletins, manuals and technical letters. The table lists what each maker's documents showed on 20 November 2026.
| Maker | What its own documents print | Status |
|---|---|---|
| Honda | Service bulletin 99-075, 9 August 2013: "EVAP control system leakage [Fuel tank system]" for 1996-00 Civic, 1998-02 Accord, 1998-01 CR-V, 2000-05 Insight, 1999-04 Odyssey, 2003-04 Pilot and 2000-06 S2000 | printed, read in full |
| Acura | Service bulletin 99-040, 8 December 2015: the same wording and the same procedure for 1997-03 CL, 1996-01 Integra, 2001-04 MDX, 1997-05 NSX, 1996-04 RL and 1999-03 TL | printed, read in full |
| Nissan | Nissan bulletins NTB09-020F (2007-2011 cars) and NTB13-097J (February 2022, all 2012 and newer), on EVAP leak codes, list P0442, P0455 and P0456, not P1456; Nissan's service manual was not available to read | not printed in the bulletins read |
| Infiniti | Infiniti's ITB13-044J, for 2012 and newer cars, lists P0442, P0455 and P0456, not P1456; a trade-press article dated 1 June 2011 summarises an Infiniti bulletin whose involved codes include P1456, but the bulletin itself was not read | summary only |
| Saab | Saab Workshop Information System, an online copy on a third-party site, 2002 9-5 with the V6 engine: "Tank purging, leak in system"; P1456 is listed among the codes set when the pressure-retaining phase (phase C) of its test fails | printed, read in full; Saab's own wording and test, not Honda's |
| Ford | Ford's manual pages could not be opened on three addresses | not read |
| Volkswagen | Volkswagen's US manual pages could not be opened on three addresses; an India-market Tiguan manual (edition 11.2021) was opened and does not contain P1456 | no code printed in the India edition |
| Toyota, Hyundai, Kia, Subaru, Mazda, Chevrolet, Ram, Dodge, Mercedes-Benz, MINI | Owner's manuals read for the cap, the light and the vapor system; the manual text read does not contain P1456 | no code printed |
The Nissan and Infiniti rows need care. The Infiniti summary on the trade site Vehicle Service Pros reads: "This TSB from Infiniti applies to 1998 and later Infiniti vehicles with EVAP service port." and "The involved DTCs include: P0440, P0442, P0455, P0456 and P1456." That is a trade magazine's summary, not the document, so we build no advice on it. iATN, a network of professional technicians, lists help requests under P1456 and prints the label "P1456: EVAP System Very Small Leak (0.020") Detected." on a 2002 Nissan Maxima, a close variant on a 2002 Nissan Sentra and Xterra, and "P1456: EVAP System Leak Detected (Fuel Tank Area)." on a 2003 Honda Civic. A 2003 Infiniti QX4 request on another iATN page reads "Evap. small leak".
What this means for you. On a Honda or Acura of the right years, P1456 is a tank-side leak and Honda's ten steps apply. On a 2002 Nissan, a trade network labels it a very small leak (a 2003 Infiniti request says "small leak"), and the maker's own wording was not readable to us. On a 2002 Saab 9-5 V6, Saab's own system words it as a tank purging leak, with its own test. On any other make, do not assume any of these.
What Honda and Acura print: the two bulletins
Honda service bulletin 99-075 is titled "Troubleshooting DTC P1456 and P1457." The copy we read is dated August 09, 2013 and says it supersedes 99-075 of October 5, 1999 and replaces 99-074 of August 24, 1999. It lists the vehicles above and splits them into two procedures. Procedure A applies to the 1998-02 Accord, 1999-04 Odyssey, 2000-05 Insight, 2003-04 Pilot and 2000-06 S2000. Procedure B applies to the 1996-00 Civic and the 1998-01 CR-V.
Acura service bulletin 99-040 carries the same title, is dated December 8, 2015, and says it supersedes 99-040 of August 9, 2013 and replaces 99-039. Its Procedure A applies to the 2001-04 MDX, 1997-05 NSX, 1996-04 RL and 1999-03 TL, and its Procedure B to the 1997-03 CL and 1996-01 Integra. The steps we compared against Honda's are the same: the voltage windows, the cap wording, the valve tests and the tank steps.
Who is meant to use them. Honda's bulletin says its information is intended for skilled technicians with the proper tools, equipment and training, and that "These procedures should not be attempted by “do-it-yourselfers,”" and Acura's carries the same notice. The numbers below describe what a shop does with a scan tool and a vacuum pump. They are not a home test.
What the bulletins do not print. The monitor's enable conditions. Step 10 sends the technician to the electronic service manual: "In the electronic service manual, search for P1456 Advanced Diagnostics. Review the enable conditions for the monitor to run." So we cannot say how warm the engine or how full the tank must be for the car to run the test.
What does P1456 mean if my car is not a Honda or Acura? The honest answer from PulsCar's reading is that it depends on the maker. Honda and Acura bulletins print it as a leak in the fuel tank system on cars from model years 1996 to 2006; an online copy of Saab's workshop system words it for a 2002 9-5 V6 as a tank purging leak, with its own test. A network of professional technicians labels it a very small leak on 2002 Nissan cars, but the two Nissan bulletins we read cover 2007 and newer cars and list only P0442, P0455 and P0456. Ford's and the US Volkswagen manual pages could not be opened, and for every other make no maker document we read prints the code, so its meaning is not established. Before buying a part, ask for the maker's own wording of the code and the maker's own test, and then use the routes below.
How Honda's test works: a pressure sensor, three valves and a 20-second hold
The bulletin names these parts. The fuel cap and the fuel fill neck are the opening you use at the pump. The EVAP canister stores fuel vapor from the tank. The FTP sensor, short for fuel tank pressure sensor, is the gauge: the engine computer reads its voltage to learn whether the vapor system holds pressure or vacuum. Between the tank and the canister sit a two-way valve with a bypass solenoid valve, called the BPS valve, and a fuel tank vapor control valve. The bulletin's note about that last valve is a useful rule of thumb: "If fuel runs out of either hose, the FTVR (fuel tank vapor control) valve is malfunctioning or the fuel tank is being overfilled. A few drops of fuel is normal."
The logic. The car re-runs its leak self-test (the EVAP monitor) only under certain conditions, which can take several days of normal driving. The technician seals part of the system, draws a small vacuum with a vacuum pump, and watches the FTP sensor on the scan tool. In the two-way valve test and the tank test, a voltage that rises by more than 0.05 volt in 20 seconds means vacuum is leaking away from the sealed section. In the later steps that cut one part out of the circuit, the logic is the reverse: if the reading now holds, the part that was cut out was the leak.
The numbers, for technicians. An FTP reading above 2.7 volts or below 2.3 volts with the key on and the engine off means the system is holding; a healthy sensor with the cap removed reads 2.45 to 2.55 volts; the vacuum targets are about 1.50 volts for the two-way valve test and about 2.10 volts for the tank test and the two cut-out tests after it. The bulletin warns: "NOTE: You may not be able to pull vacuum if there is a large leak in the system."
Before step 1. "Before starting the troubleshooting procedure, run the EVAP FUNCTION TEST with the HDS. If the system passes the test, there is no malfunction with the system in its current condition." HDS is Honda's dealer scan tool. Honda's wording is only that a passing test means no malfunction "in its current condition"; for a car that comes back more than twice with a clean test, the bulletin sends the technician to Honda's Tech Line with the test results.
The ten steps of Procedure A, in order
Shop procedure, not a home test: it needs Honda's scan tool and a vacuum pump, and it opens the fuel system. Procedure A covers the 1998-02 Accord, 1999-04 Odyssey, 2000-05 Insight, 2003-04 Pilot and 2000-06 S2000 in Honda's bulletin, and the 2001-04 MDX, 1997-05 NSX, 1996-04 RL and 1999-03 TL in Acura's. The wording below is ours; the sequence and numbers are the bulletin's.
- Read the FTP sensor. Above 2.7 V or below 2.3 V: the system is holding, go to step 10. Otherwise there is a leak, go to step 2.
- Check the fuel cap. Tight and the right cap: remove it and inspect the fuel fill neck, the sealing surface and the threads, leave the cap off, go to step 3. Loose: tighten it at least three clicks and go to step 10.
- Read the FTP sensor with the cap off. 2.45 to 2.55 V is correct. If not, check the sensor hoses and circuit, then replace the sensor.
- Test the bypass solenoid valve. About 5 inches of mercury of vacuum at the canister-side hose; it should bleed off when the valve is switched on. If not, check its circuit, then replace the valve.
- Test the two-way valve. A rise of more than 0.05 V in 20 seconds means the two-way valve and the bypass valve are replaced together.
- Test the fuel tank. Vacuum to about 2.10 V, watch 20 seconds. A rise means a leak on the tank side: go to step 7. No rise: no leak now, step 10.
- Cut out the fuel tank vapor control valve. Plug its hose at the canister and repeat. If the reading now holds, that valve was the leak and is replaced; if it still rises, go to step 8.
- Cut out the fuel fill neck and cap. Disconnect the three hoses at the fill neck, cap the openings and repeat. If the reading now holds, the verdict is "The fuel fill neck or fuel cap is leaking. Replace the fuel fill neck and fuel cap"; if it still rises, go to step 9.
- Isolate the tank-area leak. Inspect hoses and connections with a mirror and a shop light. "If you are unable to locate a leak with a visual inspection, you will need to remove the fuel tank from the vehicle to continue with the diagnosis." Test each tank hose with vacuum for 20 seconds, inspect the tank shell, and "If no damage is found, replace the tank seals for the ORVR (onboard refueling vapor recovery) and fuel pump and re-assemble."
- Confirm the repair. Clear the codes, look up the enable conditions in the electronic service manual, and drive within them until the monitor finishes. "THE EVAP MONITOR PASSED – Repair is complete." "A TEMPORARY DTC IS SET – There is a leak in the system." A set temporary code sends the technician back to step 1.
Procedure B, for the 1996-00 Civic and 1998-01 CR-V in Honda's bulletin and the 1997-03 CL and 1996-01 Integra in Acura's, runs nearly the same checks; we describe A because it covers more cars.
P1456, P1457 and the generic EVAP codes side by side
Honda prints P1456 and P1457 as two halves of one job, and gives each its own test. Where the generic codes fit is explained in the sister guides; this table is only a map.
| Code | Where the maker or the standard puts the fault | First thing the documents check |
|---|---|---|
| P1456 (Honda, Acura) | "EVAP control system leakage [Fuel tank system]" | A scan-tool reading of the tank pressure sensor, then the fuel cap and filler neck, then the sensor again and the valves between tank and canister |
| P1457 (Honda, Acura) | "EVAP control system leakage[EVAP canister system]" | The sensor reading with the cap off, then a canister-side leak test: the canister, the canister vent shut valve, the purge hose and the purge control solenoid valve |
| P0455 | A large leak in the generic scheme | See the sister guide |
| P0442 | A small leak in the generic scheme | See the sister guide |
| P0456 | A very small leak in the generic scheme | See the sister guide |
Why this matters. Honda's two codes say where the leak is, tank side or canister side. The generic codes say how big it is, and the sister guides cover that.
What the makers' manuals say about the fuel cap
The cap is the first tool-free step in Honda's procedure, so we read what the makers' own manuals say about it. The manuals are of different years and models, listed in Sources, so this is a comparison of wording, not of cars. The table shows the manuals that give a cap instruction; the next section covers the ones that describe a car with no cap.
| Maker (manual read) | What it says about the cap |
|---|---|
| Honda (2013 Civic, Canadian edition) | "If not, loosen the cap, and then retighten it until it clicks at least once." |
| Honda bulletin 99-075 (1996-2006 cars) | The cap must be made by Acura (the bulletin's own wording) and should have the words "Must be tightened 3 clicks or check engine light may come on" printed on it |
| Toyota (RAV4 Hybrid) | "After refueling, turn the fuel tank cap until you hear a click." |
| Hyundai (2023 Elantra) | "To install the fuel tank cap, turn it clockwise until it “Clicks”." |
| Kia (2025 online manual, code SK3) | "To install the cap, turn it clockwise until it "clicks" one time. This indicates that the cap is securely tightened." |
| Subaru (Legacy/Outback manual MSA5M2403A) | "Remove the cap and retighten it until it clicks." |
| Mazda (2021 CX-5) | "To close the fuel-filler cap, turn it clockwise until a click is heard." |
| Dodge (2005 Stratus Coupe) | "Tighten the gas cap until you hear a “clicking” sound." |
| MINI (2025 Countryman) | "Fit the fuel filler cap and turn it clockwise until it clicks audibly." |
| Mercedes-Benz (2022 C-Class) | "Replace the cap on the filler neck and turn clockwise until it engages audibly." |
What differs, and what does not. Every manual here that describes closing a cap says to turn it until it clicks or engages audibly. Honda's bulletin asks for three clicks on the cap it describes, Honda's 2013 Civic manual at least once, Kia one. The bulletin is about a particular cap on older cars: turn it until it clicks, and follow what is printed on the cap.
Cars with no cap: what the manuals say about capless fillers
Some cars have no gas cap at all, and the manuals we read say so. Honda's 2026 HR-V: "Your fuel tank is not equipped with a fuel filler cap." Nissan's 2026 Rogue: "The fuel tank is not equipped with a fuelfiller cap." Infiniti's 2025 QX60 prints the same statement. Chevrolet's 2026 Equinox: "The capless refueling system does not have a fuel cap." Ram's 2026 1500: "The capless fuel filler is located on the left side of the vehicle."
What can go wrong. Ram's and Chevrolet's manuals describe two flapper doors. Chevrolet's manual adds a risk particular to a capless filler: after fuel is added from a portable can through the funnel adapter, the adapter must be removed. It says "The diagnostic system can detect if the adapter has been left installed in the vehicle, allowing fuel to evaporate into the atmosphere." and, once it is removed, "A few driving trips with the adapter removed may turn off the light." Our advice: on a capless car start with the filler flaps and the adapter, not a cap. The P0455 guide covers the capless flaps in detail. Honda's 2026 HR-V and Ram's 2026 manual still mention a missing or loose cap in their light text although both describe a car with no cap; our reading is that this is general wording.
What the light means in each manual, side by side
P1456 turns on the check engine light. What the light asks of you is printed in each manual, and the makers do not use the same words. Quoted as printed, with the manual's year:
| Maker (manual) | Steady light | Flashing light |
|---|---|---|
| Honda (2026 HR-V) | "Avoid high speeds and immediately get your vehicle inspected at a dealer." | "Park the vehicle in a safe place with no flammable items and wait at least 10 minutes or more with the engine stopped until it cools." and "If the malfunction indicator lamp blinks again when restarting the engine, drive to the nearest dealer at 31 mph (50 km/h) or less." |
| Honda (2013 Civic) | "Avoid high speeds and immediately get your vehicle inspected at a dealer." and "If you drive with the malfunction indicator lamp on, the emissions control system and the engine could be damaged." | "Park the vehicle in a safe place with no flammable items and wait at least ten minutes or more with the engine stopped until it cools." and "If the malfunction indicator lamp blinks again when restarting the engine, drive to the nearest dealer at 31 mph (50 km/h) or less." |
| Toyota (RAV4 Hybrid) | "Have the vehicle inspected by your Toyota dealer immediately." | no flashing case read |
| Subaru | "You should have your vehicle checked by an authorized SUBARU dealer immediately." | an engine misfire has been detected; reduce speed, avoid hard acceleration |
| Mazda (2021 CX-5) | "If the check engine light remains on, or it flashes continuously, do not drive at high speeds and consult an Authorized Mazda Dealer as soon as possible." | same sentence |
| Mercedes-Benz (2022 C-Class) | "Have the vehicle checked as soon as possible at a qualified specialist workshop." | no flashing case in its check-engine entry |
| Hyundai (2023 Elantra) | "If the Malfunction Indicator Lamp (MIL) illuminates, potential catalytic converter damage is possible which could result in loss of engine power. In this case, have the vehicle inspected by an authorized HYUNDAI dealer as soon as possible." and "Driving with the Malfunction Indicator Lamp (MIL) on may cause damage to the emission control system which could affect drivability and/or fuel economy." | no flashing case in its MIL entry |
| Kia (2025 online manual, code SK3) | "In this case, have the vehicle inspected by an authorized Kia dealer." and "Driving with the Malfunction Indicator Lamp (MIL) on may cause damage to the emission control systems which could effect drivability and/or fuel economy." | no flashing case read |
| Nissan (2026 Rogue) | "It is recommended you visit a NISSAN dealer for this service." and "You do not need to have your vehicle towed to the dealer." | "Do not drive at speeds above 45 MPH (72 km/h)." |
| Ram (2026 1500) | "The vehicle should be serviced if the light stays on through several typical driving styles." and "In most situations, the vehicle will drive normally and will not require towing." | the light "may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage"; "If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required." and, of a failing converter, "A malfunctioning catalytic converter can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc." |
None of these manuals says a steady light is an emergency, and none says to ignore it. The range is from "immediately" (Honda Civic and HR-V, Subaru, Toyota) and "do not drive at high speeds" (Mazda) to "as soon as possible" (Hyundai, Mercedes-Benz) and "may cause damage" (Kia), to "You do not need to have your vehicle towed" (Nissan) and "will not require towing" in most situations (Ram). The drive section below names the makers and is never softer than the strictest of these statements.
The 10-minute P1456 check
Honda's bulletin is written for technicians. Its step 1 needs a scan tool, but its step 2, the cap, is something an owner can do without tools. The labels in italics say which document each comes from; anything else is our advice.
- Read the codes and write them down before anyone clears them. Honda's bulletin treats P1456 and P1457 as a pair: P1456 is the tank side, P1457 the canister side. A reader will print a generic label for the code, and, as above, that label may not be your maker's.
- Walk around the car and smell. Our advice: liquid gasoline, a wet spot or drips is a fuel leak, not a vapor code; stop and read the gas smell guide.
- Take the cap off and look at it. Honda's step 2 asks for damage to the filler neck, the sealing surface and the threads. Look for a cracked rubber ring, grit, a tether caught under the cap.
- Refit it until it clicks. Toyota, Hyundai, Mazda, Subaru, Dodge and MINI manuals say turn until it clicks; Honda's bulletin says three clicks for the cap it describes; Kia says one click. If the cap has the instruction printed on it, follow what is printed.
- Check you have the right cap. Honda's bulletin says the cap must be made by the car's maker (its text says "Acura") and should have the words "Must be tightened 3 clicks or check engine light may come on" printed on it. Hyundai's manual adds: "An incorrect fuel filler cap can result in a serious malfunction of the fuel system or emission control system."
- Write down how the last fill-up went. Honda's bulletin says that if more than a few drops of fuel run out of either hose the technician disconnects at the two-way valve (a few drops is normal), the tank vapor control valve is malfunctioning or the tank is being overfilled. Honda's 2026 HR-V manual says a nozzle that keeps turning off when the tank is not full may mean a problem with the pump's vapor recovery system: try another pump.
- Drive normally for several days and see whether the light goes out. Honda's 2013 Civic manual: "Drive for several days of normal driving." Our advice: do not clear the code to test it. Honda's step 10 clears the codes only after the repair; how to reset a check engine light explains what clearing does.
What a diagnostic should cost covers what a shop charges for the rest, and the diagnostic tool guide covers smoke machines.
What decides the cost of a P1456 repair
This guide prints no price, because no price page for this repair could be read on 20 November 2026: the parts retailers and price guides we tried did not open for us. A guide that printed a figure without a page behind it would be inventing one. What the documents do show is what drives a quote.
Which step found the leak. In Honda's procedure the work grows with every step. A cap is step 2; a sensor, a valve or the filler neck are steps 3 to 8; the tank is step 9, where the technician may have to "remove the fuel tank from the vehicle" and, if no damage is found, the repair can end with "replace the tank seals for the ORVR (onboard refueling vapor recovery) and fuel pump". A quote that goes straight to the tank should say which tests got it there.
Tested or guessed. For the sensor and valves, the bulletin's order is test, then replace. Two valves together, or the fill neck and the cap together, can be consistent with the document; a single part with no test behind it is not.
Labor and parts. The bulletins print no labor hours and no part prices.
The fees around it. A tank job can include the fuel pump seal; the fuel pump guide lists what a pump job includes.
The scale. Our advice, not a document: a cap is a cheap part you can fit yourself; a sensor or a valve means a diagnostic fee plus that part, or a valve pair; a job with the tank removed is the biggest, because the tank has to come out.
What a quote must show. The code as stored, the test that found the leak, the part, whether it is genuine or aftermarket, whether the quote includes a drive to confirm the monitor, and the cost of a re-test.
The five P1456 routes, in the order Honda's test reaches them
Route 1 · The light came on after a fill-up: the cap and the filler
The tell. A steady light a day or two after refueling, a car that drives normally, P1456 or P1457 alone.
What it actually is. The cap is the opening you handle yourself at every fill-up. In Honda's procedure it is step 2, after the sensor reading: "If the cap is loose, tighten the cap at least three clicks to properly seal the system." If it is tight, the technician looks at what it seals against: "Damage to any of these components can result in a leak and DTC P1456." Honda's 2013 Civic manual describes the same thing from the driver's seat: the message appears when "An evaporative system leak is detected. This may be caused by the fuel fill cap being loose or not being installed."
How long it takes to go out. Honda's 2013 Civic manual says several days of normal driving. Subaru: "Tightening the cap will not make the CHECK ENGINE warning light/malfunction indicator light turn off immediately. It may take several driving trips." Mazda says its check fuel cap warning light may continue until a number of drive cycles have been completed, and defines one as starting the engine after four or more hours off and driving on city and highway roads. Toyota, in its emissions-inspection section, says that when the lamp still remains on after several driving trips, "The error code in the OBD system will not be cleared unless the vehicle is driven 40 or more times."
The cheap cause that gets skipped. The seal and the tether. Subaru's manual says the light may come on if the tether is caught under the cap and says to make sure nothing is interfering with the sealing of the cap; Honda's bulletin asks for the cap to be the maker's, printed with the instruction; Toyota says "Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury."; Mazda says "use of the incorrect fuel-filler cap or not using a fuel-filler cap may result in a fuel leak, which could result in serious burns or death in an accident."
Fix it yourself: the cap, properly. Engine off, wipe the rubber ring and the filler lip, look for cracks and flat spots, refit and turn until it clicks. If the ring is damaged, our advice is a cap to the maker's part number, as Toyota and Hyundai require. Then drive normally for several days. The honest limit: if the light is still on after several days, or returns, the cap alone may not be the answer; go to Route 2 rather than buying a second cap. Do not pull fuel lines, and do not pressure the system.
At the shop: say this: "P1456 is stored, and I have already cleaned and refitted the cap. Before replacing anything, please run the maker's function test and tell me whether the system fails it now. If it passes, I would like the code left alone and no parts fitted."
Route 2 · A new cap and the code is back: the tank pressure sensor and its hoses
The tell. The cap is new or proven tight, the code returns, and nothing else is wrong.
What it actually is. The FTP sensor is the gauge the whole test depends on. Step 1 reads it with the key on and the engine off: above 2.7 volts or below 2.3 volts, the system is holding pressure or vacuum; otherwise it is at atmospheric pressure and Honda says there is a leak. Step 3 reads it again with the cap removed, when it should read 2.45 to 2.55 volts. If it does not, the bulletin says to disconnect the hoses at the sensor and check again: "If the value reads between 2.45 V–2.55 V, inspect the hoses to the FTP sensor for a restriction. If the value is still not reading 2.45 V–2.55 V, make sure there is not an open, short, or high resistance in the sensor circuit. If the circuit tests OK, replace the FTP sensor."
What this means. A code about a leak can be a gauge that reads wrong, and a shop that proposes a sensor without having looked at its hoses and wiring is skipping the middle of the bulletin.
The cheap cause that gets skipped. The sensor's own hoses. The bulletin has the technician disconnect them and read the sensor again. If the reading is then 2.45 to 2.55 volts, the hoses are inspected for a restriction; if it is still out of range, the circuit is checked for an open, a short or high resistance, and only if the circuit is fine is the sensor replaced.
Fix it yourself: not applicable. Reading a sensor voltage needs a scan tool that shows the manufacturer's data list, and the hose tests need a vacuum pump. The bulletin reads the value from the data list of Honda's own scan tool, the HDS, so ask whether the tool used can show it. The honest limit: the one thing you can do is ask for the reading.
At the shop: say this: "P1456 returned after a new cap. What did the tank pressure sensor read with the cap on and with it off, and did you check its hoses and wiring before proposing a sensor?"
Route 3 · The cap is proven tight, the sensor is fine: the valves between tank and canister
The tell. The cap is correct and tight, the sensor reads in range, and the system still fails the pressure test. A technician who disconnects the hoses at the two-way valve may find more than a few drops of liquid fuel in one.
What it actually is. The bulletin tests three valves in order. The bypass solenoid valve should let the vacuum bleed off when the scan tool switches it on; if not, the technician checks its circuit and replaces it. The two-way valve is tested with the hose capped: a rise of more than 0.05 volt in 20 seconds means the two-way valve and the bypass valve are not working, and they are replaced together. The fuel tank vapor control valve is cut out with its hose plugged: if the reading then holds, that valve was the leak.
Liquid fuel in a hose. Honda's note, described above, is an observation worth giving to the shop: it links an overfilled tank to the valve.
The cheap cause that gets skipped. Overfilling. The bulletin names an overfilled tank next to a failed valve as the reason fuel can reach the hoses. Honda's 2026 HR-V manual says: "Do not continue to add fuel after the filler nozzle has automatically stopped. Additional fuel can exceed the full tank capacity." Stop at the first click.
Fix it yourself: not applicable. These are vacuum tests on parts near the fuel tank. The honest limit: the bulletin's notice applies, and so does ordinary fuel-system caution: do not disconnect vapor hoses at home.
At the shop: say this: "Which valve test showed the leak? Did the vacuum hold with the tank vapor control valve cut out, and was there more than a few drops of liquid fuel in any hose? If you replace two valves, please explain which test condemned each."
Route 4 · The other steps cleared: the fill neck, the hoses and the tank
The tell. The cap, the sensor and the valves have been cleared and the car drives normally. If the pump nozzle keeps stopping early, Honda's 2026 HR-V manual points first at the pump, so try another pump before suspecting the car.
What it actually is. The tank carries its own seals, and Honda has the technician disconnect three hoses connected to the fill neck. Steps 8 and 9 of Honda's procedure, above, cut the neck out of the circuit and then isolate the tank area. Step 9 begins with a look, "Use a mirror and shop light to inspect as much of the fuel tank as possible," and if that finds nothing, the tank comes off the car; each hose is then tested, and "If the hose does not hold steady vacuum for 20 seconds, replace the hose." The bulletin does not say how often it comes to this, and it prints no labor hours.
The cheap cause that gets skipped. The nozzle. Honda's 2026 HR-V manual says: "If the filler nozzle keeps turning off when the tank is not full, there may be a problem with the pump's fuel vapor recovery system. Try filling at another pump." That costs nothing and rules out the pump before the car.
Fix it yourself: look, do not open. With the car cold and on level ground, look at the filler neck and the cap area for cracks, dirt or a hose hanging loose, and at the ground under the tank for a stain. The honest limit: do not disconnect fuel or vapor lines, do not work under the car on a jack alone, and do not try the pressure tests at home; Honda's notice says these procedures should not be attempted by do-it-yourselfers.
At the shop: say this: "P1456 is stored and the cap, the sensor and the valves have been cleared. Where did the vacuum leak: the filler neck, a tank hose or the tank itself? If the tank has to come down, please show me the hose that failed the 20-second hold, and quote the seals separately."
Route 5 · It is not a Honda, or the code keeps coming back: your maker's own wording and the comeback path
The tell. The car is a Nissan, an Infiniti or any make other than Honda or Acura, or a Honda or Acura of a model the bulletins list with the same code after more than two visits.
What it actually is. P1456 is a manufacturer-defined code. For Honda and Acura the document says what it is. For Nissan and Infiniti, the bulletins we could read list the generic leak codes P0442, P0455 and P0456, and iATN labels P1456 on 2002 Nissan cars as a very small leak; we could not confirm that from a Nissan document. For a 2002 Saab 9-5 V6, an online copy of Saab's workshop system words it as a tank purging leak. For every other make we could not read a maker document that prints the code, and we make no claim about it. One code-reference page we read lists a diesel exhaust temperature sensor for it on some cars and cites no maker document; we use none of that.
What to do about that. Ask the shop for the maker's own definition of the code, the test the maker specifies and the result of that test, not a label from a generic reader. The generic EVAP leak guides cover what a smoke test finds: P0455, P0442 and P0456.
The comeback path. Honda's bulletin sets a rule: "If the vehicle comes back to your dealership more than twice for the same DTC (either P1456 or P1457), and the EVAP FUNCTION TEST does not show a problem in the EVAP system, call Tech Line." The technician is to have ready the function-test result, the car's stored self-test values (Mode 6) for five named test IDs, the repair history, the date of the last repair, accessories and collision history. An owner can ask the shop two things from that list: has the function test been run and did it fail, and what repairs and accessories are on the car's record?
The cheap cause that gets skipped. The history. Honda's comeback list asks for aftermarket accessories and collision damage because either could be related to a vapor system problem.
Fix it yourself: gather the record. Write down when the light first appeared, what was replaced and when, any underbody work, accessories and the code list. The honest limit: none of it replaces the maker's function test.
At the shop: say this: "What does the maker call P1456 on this car, and which of the maker's tests did you run? If the code has come back after earlier repairs, please tell me whether the function test fails now and what the repair record shows."
When the gas cap is not the answer
Is P1456 always the gas cap? No, and PulsCar's reading of the two Honda-group bulletins shows why. Honda puts the cap at step 2 of ten: if it is loose, tighten it at least three clicks and drive until the monitor completes; if it is tight, inspect the filler neck, the sealing surface and the threads for damage. Only after that does it read the tank pressure sensor again with the cap off, then test the bypass and two-way valves, the tank vapor control valve, the fill neck and cap together, the tank hoses and the tank seals. The cap is the cheapest first step, and Honda puts it first, but if a replaced cap does not stop the code, the remaining steps of the bulletin are where a technician looks next.
Can you drive with P1456?
Can I drive with P1456, per PulsCar's reading? Have a steady check engine light inspected immediately, as Honda's 2013 Civic and 2026 HR-V manuals say, and avoid high speeds until then; Subaru's says the same if the light stays on, Mercedes-Benz says as soon as possible, and Ram says to have it serviced if the light stays on, though it will usually drive normally. If the check engine light is flashing, if you smell liquid gasoline or see fuel dripping, or if a red warning light is on, stop in a safe place away from anything flammable and follow your manual. Our advice, not a maker's: for a flashing check engine light, pull over safely, switch the engine off and have the car towed; the only exception, a flashing light alone on a car that starts and runs normally, is a shop within 2-3 miles, reached gently, at 31 mph (50 km/h) or less with light throttle.
What Honda's manuals add for a blinking lamp. Honda's 2026 HR-V manual says: "Park the vehicle in a safe place with no flammable items and wait at least 10 minutes or more with the engine stopped until it cools." and its notice adds "If the malfunction indicator lamp blinks again when restarting the engine, drive to the nearest dealer at 31 mph (50 km/h) or less." The 31 mph in our wording above is Honda's figure.
Why a vapor code and a flashing lamp are different problems. In Honda's documents P1456 describes a leak in the fuel tank system, not a misfire; the Honda HR-V, Subaru, MINI and Nissan manuals give a misfire as the reason for a flashing lamp. Honda's 2013 Civic manual still says that driving with the lamp on can do damage: "If you drive with the malfunction indicator lamp on, the emissions control system and the engine could be damaged." Hyundai says a lamp that stays on "may cause damage to the emission control system which could affect drivability and/or fuel economy."
The second rule: fuel is not vapor. Liquid gasoline on the ground, drips, or a strong fuel smell in the cabin is not a vapor code, whatever else the car says. Mercedes-Benz's message for a loose cap names a second possibility in the same sentence: "The fuel filler cap is not closed correctly or the fuel system is leaking." Our advice, not a maker's: if you smell fuel inside the car, pull over, switch off, get out and have it towed. See the gas smell guide.
What the federal complaint file shows about P1456: almost nothing
NHTSA's owner-complaint file as we hold it, 782,908 reports received from 1 January 2015 through 4 October 2026, holds one that writes the code P1456. It is from a 2017 Ford Escape owner who lists P1456 among several other codes in a report about misfires and coolant, with a label from the shop's comments next to it; it is not a Honda or Acura and is not a maker document. This is a thin pool, and the guide does not pad it.
The older Hondas and Acuras. We also read the 32 Honda and Acura complaints for model years 1996 to 2006 whose text includes one of the words EVAP, vapor, canister, purge, gas cap or fuel cap; 13 are on a model and year a bulletin names, and about a dozen are about an EVAP code, the cap, the filler or a valve. None names P1456. Two examples:
- A 2004 Acura MDX owner wrote in 2023 that a code said to replace the gas cap, that they replaced the cap with a parts-store cap and later an original-equipment one, erased the code with a reader each time, and saw it return within weeks; a shop, they said, told them to reset it and not worry. Our advice: erasing a code hides it; it does not fix a leak.
- A 2002 Honda Accord owner wrote in 2019 that a light the owner described as an "evaporated air leak in system" had been on for five months and that they had found a bolt to the fuel pump on the ground.
These are individual accounts. They echo the sequence in Honda's bulletin, cap first and parts after, but they say nothing about how often any part fails, and this guide gives no rate.
Should you buy a used car with a P1456 history?
A P1456 on a Honda or Acura model and year listed in the two bulletins is, by their own definition, a tank-side vapor leak. The documents we read do not call it a safety defect. The risks for a buyer are practical: a car that may not be ready for an inspection, and a leak that was never found.
Ask for the record. What was replaced, in what order, and what test found the leak. Check readiness. Chevrolet's manual says the vehicle may not pass inspection if "Critical emission control systems have not been completely diagnosed" and that "This can happen if the 12-volt battery has recently been replaced or run down, or if the vehicle has been recently serviced."
If the seller cleared the code. Our advice: a cleared code with no repair record is a reason to ask why; a real leak returns once the monitor runs again.
Clearing P1456 before an inspection: why it backfires
Under the federal OBD test procedure, a lit light fails the car; states set their own programs, so check yours. In 40 CFR 85.2222, if the light is commanded on, "the vehicle shall fail the OBD inspection." The rule also covers a light that does not come on at all with the key on: "If the MIL does not illuminate at all when the vehicle is in the key-on/engine-off condition, the vehicle shall fail the OBD inspection, even if no DTCs are present"
A cleared car may not be ready. The same rule allows an exception: "An exception to paragraph (c)(1) of this section is allowed for MY 1996 to MY 2000 vehicles, inclusive, with two or fewer unset readiness monitors, and for MY 2001 and newer vehicles with no more than one unset readiness monitor." A car whose EVAP monitor has not finished after a clear can use up that allowance. Toyota's manual says the vehicle may not pass the test when "the 12-volt battery is disconnected or discharged."
A real leak comes straight back. Once the monitor runs again and the leak is still there, the code returns. The honest route is the repair, several days of normal driving, and a readiness check before the test; the inspection cost guide covers the retest side, and how to reset a check engine light covers what a reset does.
Three P1456 traps to avoid
Trap 1: the second cap. The situation: a P1456 on a 2002 Accord, a new cap, the code back in a week. A shop might say: "Try a different cap." What is really happening: a replaced cap that does not stop the code sends the technician on to the sensor, the valves and the neck, not to a third cap, unless the new cap was not the maker's part or lacks the printed instruction, which Honda's step 2 does ask for. Your protective question: "What did the next test in the maker's procedure show?"
Trap 2: the label from a generic reader. The situation: a reader prints "very small leak" for a car whose maker calls the code a tank-side leak, or the other way round. A shop might say: "The code is a small leak: smoke test and replace the canister." What is really happening: a trade network labels P1456 a very small leak on 2002 Nissan cars and a tank-area leak on a 2003 Honda Civic, and on Honda's pair the canister belongs to P1457, not P1456. Your protective question: "Which maker's definition was used, and which side of the system is the leak on?"
Trap 3: the part with no test. The situation: a shop quotes a pressure sensor or a valve on the code alone. A shop might say: "That sensor is what sets this code." What is really happening: Honda's bulletin checks the sensor's hoses and circuit before replacing it, and tests each valve with a vacuum pump first. Your protective question: "Which test condemned this part?"
Three P1456 quotes, decoded
These are composite scenarios, not individual customers: the mileages and outcomes are illustrations assembled to show the sequence of Honda's steps. They carry no prices, because no price page for this repair could be read.
Scenario 1 (an example, not a real customer): the cap that was the answer. A 1999 Civic, P1456 two days after a fill-up. The owner finds grit on the rubber ring, wipes it, refits the cap until it clicks, and several days of normal driving later the light is off. Lesson: the tool-free step in the bulletin is worth doing first.
Scenario 2 (an example): the quote that skipped the middle. A 2001 Accord, a new cap and P1456 again. A shop quotes a tank pressure sensor; the owner asks what it read with the cap off. The technician finds 2.45 to 2.55 volts, so the sensor is fine and the next test is the bypass valve. Lesson: for the sensor and valves, the bulletin replaces a part only after a test condemns it.
Scenario 3 (an example): the smell. A 2004 MDX owner notices a gas smell and a damp patch under the rear of the car. This is not a vapor code: the owner follows the rule in the drive section and stops in a safe place. Lesson: a smell of liquid fuel changes the question from "which part" to "is it safe."
The P1456 plan: 10 minutes, today, this week
Next 10 minutes: free
- Write the code and every stored code down. Do not clear them.
- Smell for liquid fuel and look under the car. If you find any, stop and follow the drive section above.
- Take the cap off, look at the seal and threads, and refit it until it clicks.
Today
- Find your maker's wording for P1456. Ask a shop or your dealer; do not rely on a generic label.
- Write down how the last fill-up went and whether the pump kept clicking off.
This week
- If the light is still on after several days of normal driving, ask a shop to run the maker's function test and tell you which step found the leak.
- Replace only what the maker's test sequence points to, then drive until the monitor completes and check readiness before any inspection.
Sources and documents
Documents opened and read on 20 November 2026 (items 16, 17 and 17d are trade sources, not maker documents; 17c is a third-party site's copy of a maker's workshop system). Wording and numbers come from the documents themselves; for the Hyundai and Dodge manuals the model and year, and for the MINI and Mazda manuals the model year, are taken from the file address, as the pages read do not print them.
- Honda service bulletin 99-075, 9 August 2013 (NHTSA document 10053545): "Troubleshooting DTC P1456 and P1457".
- Acura service bulletin 99-040, 8 December 2015 (NHTSA document 10099960): the same title and procedures for Acura models.
- Honda 2013 Civic owner's manual, Canadian edition. PDF
- Honda 2026 HR-V owner's manual, copy hosted by a Honda dealer's site. PDF
- Toyota RAV4 Hybrid owner's manual, file OM0R074U (model year not printed on the pages read). PDF
- Hyundai 2023 Elantra owner's manual. PDF
- Kia 2025 owner's manual, online edition, code SK3 (the pages do not print the model name): closing the fuel filler door, warning lights, emission control system.
- Subaru owner's manual MSA5M2403A (Legacy/Outback edition). PDF
- Mazda 2021 CX-5 owner's manual. PDF
- Nissan 2026 Rogue owner's manual and Infiniti 2025 QX60 owner's manual. Nissan PDF · Infiniti PDF
- Chevrolet 2026 Equinox owner's manual. PDF
- Ram 2026 1500 owner's manual and Dodge 2005 Stratus Coupe owner's manual (Mopar archive; an old manual). Ram PDF · Dodge PDF
- Mercedes-Benz 2022 C-Class operator's manual. PDF
- MINI Countryman (MY25) owner's manual. PDF
- Nissan bulletin NTB09-020F (2007-2011 models, EVAP leak codes), NTB13-097J (NHTSA document 10208948, 7 February 2022, all 2012 and newer models except Leaf and Titan XD diesel) and Infiniti ITB13-044J (NHTSA document 10208932, 7 February 2022, 2012 and newer models): none prints P1456; the earlier D versions list the same codes. NTB09-020F · NTB13-097J · ITB13-044J
- Vehicle Service Pros, "Infiniti EVAP system leaks", 1 June 2011: a trade-press summary of an Infiniti bulletin. Article
- iATN (a network of professional technicians), P1456 code discussion pages for November 2005, September 2006, May 2008, December 2012 and November 2015: trade source, not a maker document. 17b. Volkswagen Tiguan user manual, India edition 11.2021 (not a US manual), opened and searched: no P1456. PDF 17c. Saab Workshop Information System, online copy on a third-party site, 2002 9-5 (9600), Trionic T7 V6, P1456: page. 17d. A scan-tool maker's blog post on P1456 (cites no maker document; used only for the sentence in Route 5 that says it exists): post.
- Rules and agency papers: 13 CCR 1968.2 · 40 CFR 85.2222 · EPA420-F-03-042, December 2003
- NHTSA complaint file: 782,908 owner reports received from 1 January 2015 through 4 October 2026; one writes P1456 (complaint 11601267, a 2017 Ford Escape); the 32 Honda and Acura complaints for model years 1996 to 2006 whose text includes one of the words EVAP, vapor, canister, purge, gas cap or fuel cap, read in full.
What we looked for and did not find. A Ford owner's manual and a US Volkswagen manual: the pages could not be opened on three addresses each. A Nissan or Infiniti service manual section that prints P1456: Nissan's service manual was not available to read, and the Infiniti bulletin that a trade-press article of 1 June 2011 summarises was not read, only that summary. Honda's monitor enable conditions for P1456: the bulletins send technicians to the electronic service manual for them. Labor hours and part prices for the repairs in Honda's procedure: neither bulletin prints them, and no price page we tried opened.
Related: P0455, P0442, P0456, P0441, check engine light on, the check engine code index, diagnostic costs.
Prices verified: none printed on this page; no price page for this repair could be read on 20 November 2026 · Technical documents verified: November 2026 · Reviewed quarterly

