🚨 60-Second Triage — P2195 with a flashing check engine light: Our advice, not a maker's: for a flashing check engine light, pull over safely, switch the engine off and have the car towed; the only exception, a flashing light alone on a car that starts and runs normally, is a shop within 2-3 miles, reached gently, at 31 mph (50 km/h) or less with light throttle. P2195 with a stall, lost power or no start: Our advice, not a maker's: if the engine has stalled, lost power or will not start, do not keep driving it: pull over safely, switch the engine off and have the car towed. Steady light, car drives normally: Our advice, not a maker's: a steady light on a car that drives normally can wait a few days for a diagnosis, not months. A hissing or hard brake pedal (on any car; Ford's program for 2010-2014 Edge and MKX describes a hiss, and two Edge owners with these codes wrote about their brakes): Our advice, not a maker's: if the pedal hisses or turns hard, do not keep driving it; have the car towed. If the brake pedal feels soft or sinks toward the floor, or the red brake warning light comes on or stays on while you are driving with the parking brake released, stop driving and have the car towed. Before you buy a sensor: write down every code, ask for a bulletin and program check by VIN, and look for water in the engine bay, at the sensor plugs and along the hoses first.

Short answer: the code alone cannot tell you. A shop with a scan tool can compare the readings: if the front sensor sits lean while the fuel trims and the rear sensor say something else, the front sensor is the suspect; if the sensors and the trims all say lean, the engine really is lean. Our reading of the papers below, not a maker rule. Check your VIN for a free fix first.

P2195 is one half of a question, and the sensor is only one of the two possible answers.

P2195, which a Toyota bulletin prints as "A/F Sensor Signal Stuck Lean", means that the engine computer sees the signal of the front oxygen (air-fuel ratio) sensor on bank 1 sitting on the lean side and not moving as it should. A lean mixture has too much air for the fuel. The computer cannot tell, from that one signal, whether the mixture really is lean or the sensor is wrong. Its mirror code is P2196, stuck rich; the same pair for bank 2 is P2197 and P2198. Car makers print both explanations, and a surprising number of others.

This page answers one question first: is the sensor stuck, or is the engine really lean, and which fix has a maker paper behind it? The full lean-engine diagnosis is on P0171 and P0174; wiring and connector papers are on P0130, slow response on P0133, the rear-sensor trim codes on P2096. Those pages say little or nothing about P2195 to P2198; we link to them rather than repeat them.

What does P2195 mean, and does it say the sensor is bad? In PulsCar's reading of the maker papers, P2195 says only that the front air-fuel sensor on bank 1 reports lean and stays there: Toyota's bulletin prints it as "Stuck Lean", Chrysler's diesel papers as "Out Of Range High". The papers that carry this code or its neighbours P2196 to P2198 send shops to a sensor (Ford 3.5L GTDI, Toyota), software or a computer (Ford 2.7L, Subaru, Chevrolet), water (Ford Transit, Land Rover), a harness (Ram, Ford Escape), a purge valve (Ford Focus), injectors (Ford 2018 2.7L), a cooler (Ford 2.0L) and an oil separator that should not be replaced (Porsche). Only Ford's 3.5L paper, Toyota's wire-check bulletin and Land Rover's papers (a sensor with software, or once the wiring is cleared) end at the sensor. A forum copy of a Prius manual lists the intake, fuel pressure, an injector and the EGR valve beside the sensor.

The complaint file barely contains this code. NHTSA's file of owner complaints from January 2015 through early October 2026 has 32 that print one of the four codes with the letter P (P2196 in 23, P2195 in 6, P2198 in 5, P2197 in 3; a few print two, and one P2198 is written P02198) and two more that print it as a bare number or in words. Only seven print P2195 or P2197. So this is a thin pool, and we do not turn it into a rate; the page leans on the maker papers. And the code owners write about is the rich one: 23 of the 32 are P2196, 17 of those on Ford or Lincoln cars, and many come with a purge-valve or evaporative-system story that is in the maker papers too. The counts below are complaints, not cars. The maker papers are those of Ford and Lincoln, Chrysler and Ram, Toyota, Chevrolet, Subaru, Land Rover, Audi, Porsche and, from third-party manual copies, Mazda and Saab; the makers we could not read are named below.

Claims marked 🟢 rest on a maker paper or other document in the Sources section. Claims marked ⚪ are shop-price estimates carried from our repair guides. Owner-reported figures are what people told NHTSA, published with their ODI numbers, and the complaints we counted are published too, with the sorting rules and the papers.

Words on this page. DTC: a trouble code. PCM, ECM: the engine computer. HO2S: heated oxygen sensor. MIL: the check engine light. Freeze-frame: engine data the computer saved when the code set. EGR, PCV, EVAP: the exhaust recirculation valve, the crankcase ventilation hoses, the fuel-vapor system. Bank 1: the side of the engine that holds cylinder 1. Sensor 1: before the catalytic converter; sensor 2: after it. Air-fuel ratio (A/F) sensor: a front sensor that reports how lean or rich the mixture is as a number. Fuel trim: how much fuel the computer is adding or taking away. Bulletin (TSB, SSM): a maker's repair instruction to dealers, not a recall. Flash: a software update. CPV: Ford's canister purge valve, part of the fuel vapor system. ODI number: NHTSA's complaint number.

What P2195 says: the front sensor's signal is stuck on the lean side

What a maker means by the code depends on how that maker's computer judges the sensor, and the papers show three different ways.

Toyota. 🟢 A forum-hosted copy of a 2010 Prius repair manual excerpt prints P2195 as "Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)" and warns: "Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor." It sets when the air-fuel sensor reads far too lean while the rear oxygen sensor's voltage rises, for 5 seconds, or when the sensor's current stays high during a fuel cut on deceleration (excerpt named in the sources, not linked)
stuck lean
Mazda. 🟢 A third-party copy of the RX-8 workshop manual prints "Front HO2S signal stuck lean": if the average output current is more than 1.2 A for 25 seconds under set conditions, "the PCM determines that the front HO2S signal remains lean." (page named in the sources, not linked)
stuck lean
Saab. 🟢 A third-party copy of a 9-5 workshop page prints "HO2S Signal Biased Lean Sensor 1"; the code sets when "The ECM detects that the HO2S 1 signal is biased lean." (page named in the sources, not linked)
biased lean
Audi. 🟢 Prints P219500 as "O2 Sensor Signal Biased/Stuck Lean", bank 1 sensor 1 (AVIN4APIN20260325)
biased or stuck
Chrysler and Ram. 🟢 The 6.7L Cummins pickup papers print P2195 as "O2 Sensor 1/1 Out Of Range High" and P2196 as "Out Of Range Low" (18-012-12, 25-002-14); the 3.0L diesel Ram 1500 papers print "P2196-00 - O2 Sensor 1/1 Stuck Rich." (18-021-15)
range (6.7L)
Ford. 🟢 Ford's bulletins give the code number and the part: "DTC P2195/P2626 - bank 1 sensor 1 HO2S (Right Side)" on the 3.5L GTDI (17-2124)
code and part

Read the table twice, because it holds the first trap. Stuck lean is not one test. The Prius copy compares two sensors and watches the current in a fuel cut; the RX-8 copy watches the current for 25 seconds; Chrysler's papers call the same number an out-of-range high. The code tells you which sensor the computer distrusts, not which of the two readings, the sensor's or the engine's, is true.

The Prius copy adds a fact for anyone with a multimeter: "Therefore, the air fuel ratio sensor voltage output cannot be confirmed without using the Techstream." The sensor outputs a current that the computer converts to a voltage inside itself, so a meter on the plug cannot read the sensor's output, though a shop can still test the wires and the heater. The check is a scan tool's live data for the air-fuel sensor and the fuel trims.

The code is a judgment made after a warm, steady drive. The RX-8 copy says the monitor needs, among other conditions, the engine warm (coolant above 70 °C, 158 °F), 1,000 to 3,200 rpm and closed-loop fuel control, calls it "an intermittent monitor (HO2S)", and lights the lamp after two consecutive drive cycles; the Saab copy says the code sets within 4 seconds when the condition is continuous, or within 50 seconds cumulatively. So it can set once, go away and come back, as a 2015 Ford Focus owner wrote: "ERROR CODE P2195 (BANK 1/SENSOR 1 LEAN) CAME UP, AND THEN WENT AWAY." (ODI 11155252)

P2195 symptoms: a lit lamp, and sometimes a stall

Several papers describe only the lamp: Ford's 2.7L F-150 papers (no drivability concerns) and Land Rover's. Others name more: Ford's Focus program, hesitation, rough running or stalling at low speed (24N07); Ford's Transit paper, difficulty starting and misfires (19-2091); GM's computer paper, a no-start or stall (18009). In the complaint file at least 66 of the 159 describe stalling, shutting off, lost power, limp mode or severe hesitation, a floor and not a rate. Repair publishers list a check engine light, misfires, rough running and reduced power (FIXD, MechanicBase); our car running rough and car stalls while driving pages cover those symptoms in general.

First: P2195, P2196, P2197, P2198 and their neighbours — which code is yours

Read the exact code, and the whole list, before you buy anything. The neighbours look alike and the papers treat them differently.

P2195 / P2197 — front sensor signal stuck (biased) lean, bank 1 / bank 2. 🟢 Ford's 3.5L GTDI paper replaces the sensor per code (17-2124); Toyota's 2005-2010 paper replaces the air-fuel sensor only, after a wire check (T-SB-0001-10)
this page
P2196 / P2198 — the same sensor stuck rich. 🟢 In Ford's papers it is the code that comes with software, injectors, a purge valve and a harness above the steering shaft; in Subaru's, a software quirk after the throttle is snapped open and shut
this page
P0171 / P0174 — system too lean, bank 1 / bank 2; a verdict on the mixture
P0172 / P0175 — system too rich, bank 1 / bank 2
P0130 to P0135 — circuit, range, slow response, no activity, heater on the same sensor
P2096 to P2099, P219A, P219B — rear-sensor fuel trim limits, and the air-fuel imbalance code

Banks. 🟢 Ford's 3.5L GTDI bulletin prints P2195 as the right side, bank 1 sensor 1, and P2197 as the left side (17-2124); other makers may number the banks differently, so check your own paper. Spellings. Audi and Porsche print the code plus two digits (P219500, P219800), the Chrysler papers print P2196-00, and some owners write the number alone: "OCCASIONALLY THE CAR WILL THROW A 1450, 2196, OR 0131 CODE." (ODI 11172036)

The pair rule. 🟢 When a paper lists P2195 it often lists some of P2196, P2197 and P2198 too. Ford's Transit papers list all four with P0171, P0172, P0174, P0175 and water (17-0014), Chrysler's flash lists both bank 1 codes in a list of engine codes, Land Rover's SSM72448 lists them among 80 oxygen-sensor codes and says the cause "has yet to be identified" (SSM72448). A code list is a symptom list, not a recipe.

The maker atlas: who prints a sensor, software, water, a purge valve, injectors or a harness

The papers split by maker, and the split is the most useful thing in them: a Transit with water over the engine, an F-150 with a software flash and a Toyota with a wire check carry the same code family and are on three different roads. Years, engines and build dates are as printed.

Ford, 3.5L GTDI. 🟢 On 2015-2017 Explorers and 2015-2016 F-150s with P2195, P2197, P2626 or P2629: "Yes - replace the affected heated oxygen sensor (HO2S)." Labor allowances of 0.5 to 0.8 hour, by side or both (17-2124)
sensor, per code
Ford, 2.7L EcoBoost F-150. 🟢 P2196 and P2198 with the lamp on and "no drivability concerns" (the 2018 and 2019-2020 papers): dealers were told to clear the codes and advise the customer that a repair is coming and that the condition has "no effect on vehicle operation or long term durability" (SSM 48956, 48957; the earlier 48789 omits "no drivability concerns"). The repair was a flash, 0.3 hour, for 2019-2020 trucks built on or before July 4, 2020 (20-2257, then 21-2045). For 2018 trucks built on or before July 12, 2018 with misfire and lean codes too, the first papers (trucks with more than 500 miles) replaced six direct injectors, 4.4 hours, when the fuel rail pressure dropped below 10 psi within 30 seconds after the engine was shut down (18-2270, then 18-2310); Ford prints the limit as "6.9 kPa (10 psi)", and the two figures do not match, since 10 psi is about 69 kPa. The replacement says the cause "may be due to software in the powertrain control module (PCM) or direct injection fuel injectors leaking down", flashes first, and keeps the same test; its step 2 reads "before 12-Jul-2018" (20-2324)
flash, injectors
Ford, Focus and Police Interceptor. 🟢 P2196 is one of the codes that send dealers to the canister purge valve: "Replace the evaporative emission canister purge valve." on 2012-2015 Focus cars built on or before January 21, 2015 (16-0062; the earlier 15-0034 covers 2012-2014); the 2024 program for 2012-2018 Focus cars lists "P2195 and/or P2196" (24N07); the 2017 Police Interceptor program lists P2196 and P2198 (17M06)
purge valve
Ford, Transit. 🟢 On 2015 vans, then 2015-2018 vans, P2195 to P2198 with P0171, P0172, P0174 and P0175, hard starts or misfires "may be due to undesired water entry into the engine compartment directly over powertrain components"; the fix is a water deflector, an air filter, a mastic patch and a revised air cleaner cover (17-0014, 19-2091)
water
Ford, Escape and 2.0L EcoBoost. 🟢 On 2020-2021 Escapes, a harness above the steering shaft can short, blow fuse 44 and set P2196 among more than 20 codes (SSM 50116, 50245); on 2019-2020 2.0L cars, an EGR cooler "leaking coolant into the engine intake and exhaust system" (SSM 48345); on 2019 Edge and Nautilus 2.0L built on or before January 23, 2019, PCM software settings (19-2046)
harness, EGR
Chrysler and Ram. 🟢 For 2010-2012 Ram 2500 and 3500 6.7L Cummins pickups, an overlay harness replaces the sensor wires and shops are told not to replace any parts first (25-002-14); the quotation is in the FAQ above, and the earlier version, which installs new connectors, is on our P0130 page (25-004-12). For the 2014 3.0L diesel Ram 1500, P2196-00 sits in a long list answered by a PCM flash, with an oxygen sensor and an exhaust temperature sensor among the parts, "depending on Diagnostic Trouble Codes (DTCs) that may have set" (18-021-15); for the 2015, 18-019-15 is the flash alone
harness, flash
Toyota. 🟢 For Avalon (2005-2010), Camry, Highlander, RAV4, Sienna and Venza (each from its own first year to 2010) with P0138 or P0158: "In some instances a P2195 or P2197 (A/F Sensor Signal Stuck Lean) DTC may also be present. This condition may be caused by incorrect Air Fuel Ratio Sensor response." With P2195 or P2197 present, inspect the sensor's A1A+ and A1A- wires for an open or short, and if none, replace that bank's sensor "ONLY" (T-SB-0001-10)
wires, sensor
General Motors. 🟢 On the 2018 Chevrolet Malibu with the 1.5L LFV engine, a computer with a wrong bootloader version "may result in a no-start or stall" and codes including "P1133/P2195/P2196"; dealers replace the computer as needed, and GM estimated only 49 vehicles would need it (18009)
computer
Subaru. 🟢 On the 2019 Ascent, P2196 can be set by a reading quirk: "if the driver "snaps" the throttle open and shut rapidly, normal judgement of the A/F sensor data may be inaccurate and cause the code to be detected in error." The fix is ECM reprogramming (11-183-18R)
software, false code
Land Rover. 🟢 The 2016 reissue for the 2014-2016 LR4, the 2014-2015 Range Rover Sport and the 2013-2015 Range Rover (3.0L V6 or 5.0L V8 supercharged, within VIN ranges) lists P2195 to P2198 among the heated-sensor codes, gives water on the heated sensing element as a possible cause (quoted on our P0133 page), and replaces only the affected sensor, with new software (LTB00671NAS6); for later builds and the 2.0L GTDi the cause "has yet to be identified" and, when the wiring and connector are found clean, the sensor is replaced and kept for return (SSM72448)
water, unknown
Audi and Porsche. 🟢 Audi lists P219500 for a 2025 Q5 and A5 as "O2 Sensor Signal Biased/Stuck Lean" and says to contact its technical line (V4P list). Porsche says that on the 2017-on Macan and Cayenne, with P219800 and three other sensor or trim codes, the oil separator "is being replaced for no reason" (Porsche 20/20)
keep separator
Mazda. 🟢 A third-party copy of the RX-8 manual lists four possible causes, "Front HO2S malfunction", "Fuel injector malfunction", "Fuel line pressure malfunction" and "PCM malfunction", and checks them in that order (RX-8 copy, not linked)
sensor first

The surprise is how seldom a paper says "replace the sensor" and stops. 🟢 Ford's 3.5L GTDI paper does that outright; Land Rover's SSM72448 applies only after the wiring and connector are found clean and asks the shop to keep the replaced sensor for return; Toyota's does it for one bank after a wire check. The other papers we read that carry these codes send the shop somewhere else: to software or a computer (Ford 2.7L, Subaru, Chevrolet, Ram 3.0L), to water (Ford Transit), to a harness (Ram, Ford Escape), to a purge valve (Ford Focus), to injectors (Ford 2018 2.7L), to a cooler (Ford 2.0L) or to not replacing a separator (Porsche).

What we could not read. Honda, Hyundai, Kia, Nissan and Infiniti, Volkswagen, BMW, Mercedes-Benz and Suzuki do not appear in the papers that name these codes in NHTSA's index, and their service-information sites are by subscription or did not answer (Honda's returned a service-unavailable error; Hyundai's and Nissan's open on sign-in or landing pages). The Hyundai case below is from a repair-data publisher, not a maker. Two manual pages, a Mazda 3 and a Toyota V6, were blocked, so the RX-8 and Prius copies stand in for those makers.

Stuck sensor or really lean engine: compare the two readings

If the sensor is stuck, the engine's real mixture and the sensor's report disagree. If the engine really is lean, they agree. Everything the papers print about diagnosis is a way to compare the two.

Compare it with the fuel trims. 🟢 A repair-data publisher's Hyundai case shows the logic best. On a 2007 Elantra (122,060 miles) with P0171, P0170 and P2195, the long-term fuel trim read +49% and the rear oxygen sensor "was reading rich at all times". The technician unplugged a vacuum hose: "Only the rear O2 sensor reacted to the vacuum leak; the front did not." The technician replaced the front sensor, and the trim read 0% to +5% afterwards (ALLDATA tech tip, January 14, 2016). It is one case from a publisher, not a maker rule, but it shows the test: a front sensor that does not react when the mixture is changed on purpose is the one that is stuck.

Compare it with the other sensor. 🟢 Toyota's paper for P0138 or P0158 without P2195 or P2197 is a comparison too: its freeze-frame test sets the air-fuel sensor at 3.35 to 3.70 V against the rear sensor at 0.70 to 0.90 V (T-SB-0001-10; the result is on our P0130 page).

Look for what a lean engine would leave. 🟢 Ford's papers show causes that are not the sensor: a canister purge valve that "may not operate as intended" on a Focus (24N07); direct injectors "leaking down" on the 2018 F-150 2.7L (20-2324); water over the engine on a Transit. Owners add a worn brake booster (route 3) and a cracked intake or a PCV fault (see P0171). If one is present, the sensor may be telling the truth, and a new sensor would not fix the cause. Repair publishers add an exhaust leak ahead of the sensor, a dirty airflow sensor and low fuel pressure (FIXD, MechanicBase); our P0130 page has the maker papers on exhaust leaks near a sensor. MechanicBase also describes a swap test on two-bank engines, moving the suspect sensor to the other bank to see whether the code follows it; our advice, not a maker's: that is a shop job.

The 10-minute P2195 check

Our advice, not a maker's, built from what the papers above print and our vacuum-leak guide. A scan tool with live data makes the first part much better; a free parts-store read gives the codes only.

  1. Write down all the codes and the freeze-frame, and do not clear them. The RX-8 copy's step 1 is to record the freeze-frame data.
  2. Look up your car in the atlas above. If it is listed, ask the dealer for the paper by number, and for programs by VIN.
  3. Look for water. Ford's Transit papers inspect the air cleaner element for water or ice; Land Rover prints water on the heated element. Check the engine-bay plugs for damp, green corrosion or fluid.
  4. Look at the sensor plug and wires, engine off and cool. Toyota's step is an open or short on A1A+ and A1A-; Ram's papers replace connectors and wires before parts.
  5. Check for a hiss or a change in the pedal, parked, with the parking brake on. On a 2010-2014 Edge or MKX, Ford's program describes a hiss and a spongy pedal. If the brake pedal feels soft or sinks toward the floor, or the red brake warning light comes on or stays on while you are driving with the parking brake released, stop driving and have the car towed.
  6. Listen at idle for an air leak and check the oil cap, intake duct and PCV hoses, as on our vacuum-leak guide.
  7. Ask the shop for the fuel trims and front-sensor data, with a reason, before any part.

Keep hands, hair and loose clothing away from the fan and belts with the engine running. Do not spray anything flammable at a running engine to look for a leak, and do not touch a hot exhaust: our advice, with no maker paper behind it.

Six P2195 situations, and which is yours

1. A 2019-2020 F-150 with the 2.7L, the light on and no symptoms, P2196 and P2198. Ford's 2020 papers say the condition has no effect on operation and durability and send the truck for a 0.3-hour flash. A 2018 truck built on or before July 12, 2018 gets the flash first and then a fuel rail pressure test that may lead to injectors. Ask by VIN; do not buy a sensor
route 1
2. A Focus that stalls at a stop or, as owners write, after refuelling, P2196 or P2195 with P1450 or P0443. Ford's papers and its 15-year program replace the purge valve. Ask for 24N07 and the recall check; a stall means tow it first (triage box)
route 1 or 3
3. A 2015-2018 Transit with misfires or hard starts, P2195 to P2198 with lean and rich codes. Water over the engine; the paper is a water kit
water, route 2
4. A 2015-2017 Explorer or 2015-2016 F-150 with the 3.5L, P2195 and P2197 alone. The paper replaces the sensor by code
route 4
5. A 2010-2014 Edge or MKX with a hiss at the brake pedal, engine shutting off at a stop, P2195 and P2197. A brake booster leak is the story two owners tell. The booster program has ended
route 3
6. A 2005-2010 Toyota with P0138 or P0158 and P2195 or P2197. Check the air-fuel sensor wires, then replace that bank's air-fuel sensor only
route 4

The P2195 price ladder, from the bottom up

Every number is a maker's labor allowance (a warranty figure, not a shop price), a figure carried from one of our repair guides (⚪), or an owner's report. We add no price of our own.

A program the maker pays for. 🟢 Ford 24N07 (one-time purge valve, 15 years from warranty start). A bulletin is paid only inside the warranty limits: Ford's TSBs say warranty coverage limits "are not altered by a TSB"
$0 if it applies
A software flash. 🟢 Ford allows 0.3 hour of labor for the 2.7L F-150 flash; outside warranty you pay the shop's rate for that time
0.3 h labor
A diagnosis. ⚪ Our diagnostic guide carries $80 to $150 at independent shops and $120 to $300 at dealers; parts stores read codes for free (how much does a car diagnostic cost)
$80 to $300
A split hose or duct. ⚪ A $15 to $40 part; the guide puts a smoke test at $60 to $150 and a fuel pressure test at $50 to $150 (P0171)
$15 to $40+
A front sensor. ⚪ $150 to $500 installed, part $30 to $80 quality aftermarket or $80 to $300 original (O2 sensor guide); 🟢 Ford allows 0.5 to 0.8 hour on the 3.5L GTDI
$150 to $500
Injectors. ⚪ A port injector $150 to $350, a direct-injection one $350 to $700 (fuel injector guide); 🟢 Ford allows 4.9 to 5.0 hours for the six on the 2018 F-150 2.7L (4.4 in the first two papers)
$150 to $700 each
A fuel pump. ⚪ $600 to $1,500 (fuel pump guide)
$600 to $1,500
What owners reported for sensor-related work. From $148 for one oxygen sensor that did not cure the problem to nearly $4,500 for a harness quote (eight owners, below)
$148 to $4,500

How much does it cost to fix P2195? In PulsCar's reading of the papers, it ranges from nothing to thousands, and the sensor sits in the middle. A program costs nothing when it applies, and a bulletin only inside the warranty limits: Ford allows 0.3 hour for the 2.7L F-150 flash, and its Focus program replaces the purge valve once for 15 years from the warranty start. Our guides carry $150 to $500 for a front sensor installed, $150 to $350 for a port injector, $350 to $700 for a direct-injection one, $600 to $1,500 for a fuel pump and $80 to $300 for a diagnosis. Eight owners in the federal file gave figures from $148 to nearly $4,500, the two largest for harness and engine work. A sensor does not fix a purge valve, a leaking booster or water on the engine.

The five P2195 routes, the cheap checks first

The routes are five answers to the question this page asks, ordered by what is cheapest to check, not by what the repair costs. A bulletin search and a look cost nothing, a trim read costs a diagnosis, and only then comes a part. Run them in order unless your car is already in a paper.

Route 1 · Software, a program or a free repair — $0 when it applies; Ford's labor allowance for a flash is 0.3 hour

What it is. The maker prescribes a reprogram or a no-charge repair.

What the documents say. 🟢 Ford's 2.7L F-150 papers are the clearest: "This may be due to software in the PCM." (20-2257), with a 0.3-hour flash. Subaru, Chevrolet and Ram flash or replace the computer too (atlas above), and Ford's 24N07 replaces a Focus purge valve once, at no charge, if the car shows one of its codes, which include "P2195 and/or P2196" (24N07).

What the owners report. 15 of the 159 complaints end at a bulletin, a recall, a program or a software step. A 2016 Focus owner with P2196 and P1450 writes that the VIN "DOES NOT SHOW IN SAFETY RECALL", "CHECKED BY FORD DEALER", while citing Ford's recall 18S32-S1 for a software update and the canister purge valve (ODI 11258288). And a 2013 Altima owner writes that "DURING WARRANTEE IT ONLY REQUIRED REPROGRAMMING THE ECM", but that after the warranty ended "SAME CONDITION REQUIRES $400 SERVICE TO REPLACE AIR/FUEL SENSOR" (ODI 10807711).

The cheap cause that gets skipped. The bulletin search itself. It costs nothing, and the papers above show Ford, Subaru, Chevrolet and Ram answering these codes with a flash, a computer or a no-charge repair. A shop that quotes a sensor before it has read your VIN's list has skipped the cheapest line on the ladder.

At the shop — say this: "Please check this VIN for bulletins, campaigns and extended coverage that name P2195, P2196, P2197 or P2198, and tell me whether the engine computer's software is current, before you quote a sensor."

Route 2 · Water, wiring and connectors — $0 under a paper; one owner was quoted nearly $4,500 for a harness and parts

What it is. Something around the sensor is wrong: water, a wire, a plug, a harness that rubs.

What the documents say. 🟢 Ford, on 2015-2018 Transits, ties the P2195 to P2198 list to water over the engine (atlas above; 17-0014, last revised as 19-2091, which prints one build date, July 24, 2018, in its summary and June 24, 2018 in its criteria, so ask which applies). Ford, on 2020-2021 Escapes, a harness above the steering shaft can short and set P2196 among many codes (SSM 50116). Chrysler's 2014 paper installs an overlay harness and tells shops not to replace any parts before the bulletin and its test (25-002-14). Toyota's step 3: if the sensor's A1A+ or A1A- wire is open or shorted, "Repair the harness and revaluate the Air Fuel Ratio Sensor operation." (T-SB-0001-10). The connector and harness papers are on our P0130 page.

What the owners report. 11 of the 159 end at a wire, fuse, harness or fluid. A 2011 Ram 2500 owner with P241A and P2196 replaced the sensor three times in a year and was told it is the harness (ODI 11056284). A 2003 4Runner owner with lean codes had the air-fuel and airflow sensors replaced again and again, was quoted nearly $4,500 for a new engine harness and other work, and writes "YOU CAN CLEARLY SEE THE FLUID WHEN YOU UNPLUG THE O2 SENSOR FROM THE HARNESS" (ODI 10823454).

The cheap cause that gets skipped. A wet air filter, a clogged cowl drain, a plug with fluid in it. All are visible with the engine off.

Fix it yourself, where honest. Our advice, not a maker's: you can look. Engine off and cool, check the plug for damp, green corrosion, oil or fluid, and the wire for rubbed insulation; take a photo; do not unplug anything you cannot reseat. Repairs to the harness belong to a shop.

At the shop — say this: "Before a sensor, please inspect the sensor plug and wires and the harness routing, and look for water or fluid on the engine-bay connectors; show me what you find."

Route 3 · The engine really is lean: a purge valve, injectors, a leak or the fuel supply — $0 under a program; our guide carries up to $1,500 for a fuel pump, and a direct-injection injector set costs more

What it is. The sensor is telling the truth: the mixture is lean. This route belongs most to P0171 and P0174; here is what the papers for these codes add.

What the documents say. 🟢 The Prius and RX-8 manual copies both list the engine beside the sensor (intake, fuel pressure, an injector, the EGR valve; see the atlas). Ford's Focus paper replaces the purge valve, inspects the canister for liquid fuel and checks whether the tank bottom is deformed upward by more than 25 mm (1 inch) (16-0062); the 2024 program says "A failed CPV may lead to drivability concerns such as engine hesitation, running rough, or stalling at low speed, and will be accompanied by an illuminated MIL." (24N07; the Focus recalls are on our P0496 page). Ford's 2018 F-150 2.7L paper, for trucks built before July 12, 2018 (its step 2), reads the fuel rail pressure after shut-down and replaces the direct injectors if it falls below 10 psi within 30 seconds, as Ford prints it (20-2324). Ford's brake booster program for 2010-2014 Edge and MKX describes "a small tear in the diaphragm" and "a hissing noise while depressing the pedal"; it names no code (13N02 S3).

What the owners report. 55 of the 159 name a really lean cause, the largest group. Reading the notes: at least 20 name an air-side cause (PCV, manifold, a hose or the brake booster), 16 a fuel-supply one, 11 injectors, 8 the purge valve and 5 the airflow sensor; the groups overlap. Two Edge owners tie P2195 and P2197 to the booster program or the booster leak. One, in 2025: "Now I know that the compromised engine vacuum from the booster air leak is impacting the fuel/air balance." (ODI 11703726). A 2022 Subaru Impreza owner also names a brake booster failure that caused an air leak in the intake and a failed air-fuel sensor (ODI 11763372). These are owners' explanations; Ford's program text does not say it.

The cheap cause that gets skipped. On a Ford with an evaporative-system code (P1450, P0443, P0456) next to P2195 or P2196, the purge valve; on any car, a PCV hose, the oil cap or an intake boot. A purge valve is a part and a program, not a sensor.

Fix it yourself, where honest. Our advice, not a maker's: check the oil filler cap and dipstick are seated, look and listen along the intake duct and PCV hoses with the hood open (hands, hair and loose clothing away from the fan and belts), and, parked with the parking brake on and the engine idling, press the brake pedal and listen for a hiss; our vacuum-leak guide has the tests the repair publishers print. If the pedal hisses or turns hard, that is not a DIY fix. Our advice, not a maker's: if the pedal hisses or turns hard, do not keep driving it; have the car towed. If the brake pedal feels soft or sinks toward the floor, or the red brake warning light comes on or stays on while you are driving with the parking brake released, stop driving and have the car towed.

At the shop — say this: "Please show me the fuel trims and the front sensor's live data, check for an air leak and the purge valve, and, on a 2018 Ford F-150 2.7L built before July 12, 2018, the fuel rail pressure drop after shut-down, before you replace a sensor."

Route 4 · The sensor itself — ⚪ $150 to $500 installed; owners report $148 to $400 for a sensor alone

What it is. The front sensor is the part that is stuck.

What the documents say. 🟢 Ford, 3.5L GTDI (2015-2017 Explorer, 2015-2016 F-150), P2195 or P2197: "Yes - replace the affected heated oxygen sensor (HO2S).", 0.5 to 0.8 hour (17-2124). Toyota, on certain 2005-2010 Avalon, Camry, Highlander, RAV4, Sienna and Venza models, after the wire check: "Replace the applicable bank Air Fuel Ratio Sensor ONLY to correct the P2195/P0138 or P2197/P0158 DTC condition." (T-SB-0001-10). A third-party copy of Mazda's RX-8 manual, step 7: "Replace the front HO2S" if the inspection finds a fault (RX-8 copy, not linked).

What the owners report. 12 of the 159 end at a sensor with no other cause named, and some of the rest say a sensor did not cure it. At least 44 say the problem returned or a first repair did not hold. A 2014 Passat TDI owner with P2196 had the O2 sensor repaired for a negotiated $300, and the light came back 13 days later with a different diagnosis (ODI 10893446). A 2016 Acadia owner writes of a $300 sensor, then $2,200 of other work, then a $3,725 quote tied to a bulletin (ODI 11549814).

The cheap cause that gets skipped. Everything in routes 1 to 3. A sensor replaced into water, a rubbed harness or an air leak meets the same trouble; the Jaguar Land Rover paper on over-replacement is under "Why P2195 comes back" and in trap 3.

At the shop — say this: "Which code, which bank, which test shows the sensor is the stuck part, and what happens to the code if the engine is made richer or leaner on purpose? Please put it in writing before you replace it."

Route 5 · Something else sets the code or hides behind it — a cooler, a separator, engine damage — $0 to the cost of an engine

What it is. A fault elsewhere pushes the reading, or the code is one of many that a larger fault sets.

What the documents say. 🟢 Ford, on 2019-2020 2.0L EcoBoost cars: low coolant, white smoke or a light with P2196 among P0217, P0401 and others "may be due to an EGR Cooler that is leaking coolant into the engine intake and exhaust system", to be tested first by visual inspection and a pressure test (SSM 48345). Porsche, on the Macan and Cayenne: "Continue fault finding to determine the cause of the fault memory entries for the oxygen sensors." (Porsche 20/20). The Prius copy lists the EGR valve and the computer among the trouble areas.

What the owners report. 15 of the 159 name an engine cause and 8 the exhaust or catalytic converter. A 2017 Fusion owner with P0303, P0300 and P2196 was told coolant had got into the engine and was quoted $9,000 for a replacement (ODI 11560714). A 2019 Sportage owner with P2196 and other fuel-trim codes was told the dealer found nothing affecting drivability; nine days later the light flashed, the engine knocked and died, and the dealer found no compression and quoted $6,700 (ODI 11630646). These are single accounts, not a rate.

The cheap cause that gets skipped. Reading the other codes. A misfire code, a coolant-loss code or an EGR code stored next to P2195 or P2196 changes the question from the sensor to the engine.

At the shop — say this: "Please read the whole list of stored codes and the coolant level before you quote the sensor, and tell me whether anything else on the list explains it."

If the light is flashing, or the engine shakes, misfires or loses power, the safety rules in the triage box apply before any of this: Our advice, not a maker's: for a flashing check engine light, pull over safely, switch the engine off and have the car towed; the only exception, a flashing light alone on a car that starts and runs normally, is a shop within 2-3 miles, reached gently, at 31 mph (50 km/h) or less with light throttle.

The coverage file: which programs and papers pay in November 2026

A bulletin is a repair instruction, not a recall, and it does not extend a warranty by itself. Ford's bulletins for the 3.5L and 2.7L engines say so: warranty limits "are not altered by a TSB". Only a program, a campaign or an extension changes who pays. Status below is our computation from the printed terms, as of 20 November 2026; your dealer's lookup by VIN decides.

Ford 24N07, canister purge valve, 2012-2018 Focus built August 1, 2010 to May 10, 2018. 🟢 One-time replacement, "15 years of service (unlimited miles) from the warranty start date", printed December 4, 2024; step 1 lists P2195 and P2196 among the codes. Cars built from August 2010 reach 15 years from their warranty start between August 2025 at the earliest and about 2033, so the oldest may already be past it (24N07)
oldest may have ended
Ford 17M06, purge valve, 2014 Police Interceptor Sedan and 2014-2016 Utility. 🟢 10 years or 120,000 miles from warranty start, and for vehicles already past a limit, through March 31, 2018; lists P2196 and P2198 (17M06)
ended for nearly all
Ford 13N02, brake booster, 2010-2014 Edge and MKX. 🟢 10 years or 150,000 miles from warranty start; for cars already past those limits, coverage expired on January 31, 2015 (built May 3, 2010 to March 28, 2013) or "will last through November 30, 2025" (built April 2, 2013 to February 28, 2014; supplement 3, February 20, 2024). The paper names no code (13N02 S3)
ended
Chevrolet 18009, engine computer, 2018 Malibu 1.5L. 🟢 A service update that expires at the end of the car's new-vehicle warranty, a period the paper does not print (18009)
ask by VIN
Ford 2.7L and 3.5L papers, Transit papers, Ram papers, Subaru 11-183-18R. 🟢 Repairs under the existing warranty only; Chrysler's papers say "ALL REPAIRS ARE REIMBURSABLE WITHIN THE PROVISIONS OF WARRANTY." (25-002-14). Toyota's 2010 tip prints "Not Applicable to Warranty" for its labor operation (T-SB-0001-10)
no extension printed

The rule that follows: a new owner of a car past its warranty should ask for every program by VIN, not for "the bulletin". Three of the programs above start the clock at the warranty start date, not the date you bought the car; an Edge owner in the complaint file was told "to late", which fits the printed dates. No recall summary in NHTSA's recall file names P2195 to P2198; owners cite Ford's Focus recall 18S32 (NHTSA 18V-735), covered on our P0496 page.

What 159 complaints show about lean and front-sensor faults

We searched NHTSA's complaint file, received from January 2015 through 4 October 2026, for every narrative that prints P2195, P2196, P2197 or P2198, that uses front or air-fuel sensor wording, or that describes a lean fault with a sensor or a code. 174 came back; 159 describe a lean or front-sensor fault on the owner's own car. The other 15 are motorcycles, or mention lean only in a pasted bulletin title, or have no lean fault at all. Only 34 of the 159 print one of the four codes or its name, and only 7 print P2195 or P2197. That is why we do not write "owners report P2195" about the rest, and why none of the shares below is a rate.

What the owners say was found or done, by the stated cause (every complaint has one):

A really lean cause named: a leak, the PCV system, a manifold, the brake booster, the purge valve, an injector, the fuel supply, the airflow sensor
55 (35%)
No diagnosis or repair stated, or still unrepaired
43 (27%)
A bulletin, recall, program or software step
15 (9%)
An engine cause: a misfire, coolant or oil use, internal damage
15 (9%)
The front sensor was replaced and no other cause is named
12 (8%)
A wire, fuse, harness or fluid on the plug
11 (7%)
The exhaust or the catalytic converter
8 (5%)

Three things stand out. First, the biggest group is a lean engine, not a bad sensor. Only 12 of the 159 end at a sensor, and 55 name a cause that would make the engine lean. This is not how often a P2195 is a sensor: the search favors owners who wrote the word lean. Second, the code owners write is the rich one, with an evaporative code beside it. 23 print P2196 with the letter P, and 14 of the 34 print P1450 (or the number 1450) with it, the code Ford's purge-valve papers list; of the 34, 8 are Focus cars, 5 Edges and 4 Fusions, and 22 are Fords and 2 Lincolns. Third, many describe a stall. At least 66 of the 159 describe stalling, shutting off, losing power, limp mode or severe hesitation, and at least 44 say the problem returned or a first repair did not hold; both are floors, not totals.

Seven print P2195 or P2197: two Focus cars with stalls, two Edges (one with a brake booster leak), a 2013 F-150 unrepaired at 166,398 miles, a 2006 Mercedes E350 and a 2018 Camry with a fuel pump recall (ODI numbers in the file). Seven stories are not a pattern.

What owners say they paid

Under one written rule: a dollar figure the owner gives as a charge, bill, quote or estimate for work the owner ties to the sensor, its wiring or a lean cause on that car, including later work after the same codes returned. Excluded: engine, throttle-body and other work with no link to the sensor or the lean fault, and mileage. Eight owners give such figures (some give more than one); they range from $148 to nearly $4,500, and each is one owner's bill or quote, not an average.

2012 Jeep Liberty — charged for an oxygen sensor; the trouble came back within five miles (ODI 10915517)
$148
2014 Passat TDI, P2196 — negotiated for an O2 sensor repair; light back in 13 days (ODI 10893446)
$300
2013 Altima — to replace the air-fuel sensor after the warranty (ODI 10807711)
$400
2016 Acadia — a sensor, then other work, then a quote tied to a bulletin (ODI 11549814)
$300 to $3,725
2003 4Runner — one visit with the air-fuel and airflow sensors, and a harness quote (ODI 10823454)
$798.76; $4,500
2016 Altima — dealer wanted for a heat shield, an air-fuel sensor and a PCV valve under a bulletin (ODI 11317021)
$1,256.86
2020 EcoSport, P0496 and a stuck-rich sensor code — a dealer quote, plus a diagnosis fee (ODI 11728678)
$900 + $250
2014 Forester — engine work to reseal the camshaft carrier covers and an air-fuel sensor (ODI 11486440)
nearly $4,000

The sensor alone sits at $148 to $400 in owners' words, in line with the $150 to $500 our O2 sensor guide carries; the two biggest are a harness quote and an engine job.

Why P2195 comes back after a repair

The cause was not the sensor. Jaguar Land Rover's SSM72035 (on Jaguar cars; trap 3 below) gives two possible reasons for unneeded replacements: all sensors replaced when only one is unserviceable, and code information that may not be clear about which sensor to change. The Hyundai case shows the same truth the other way round: the front sensor was the part that did not react.

The repair has a second step. Ford's 2.7L paper flashes first and tests the fuel rail pressure before it replaces injectors; Toyota checks the wires before the sensor; Ford's Focus program is a one-time replacement, and the paper does not say what happens if the new valve fails too.

Can you drive with P2195?

Can you drive with P2195, and for how long? In PulsCar's reading of the maker papers, none of them tells the owner to stop driving for this code alone, and Ford's 2.7L F-150 notes say the lit-lamp, no-drivability-concern case has no effect on operation or durability. Our advice, not a maker's: a steady light on a car that drives normally can wait a few days for a diagnosis, not months. Our advice, not a maker's: if the engine has stalled, lost power or will not start, do not keep driving it: pull over safely, switch the engine off and have the car towed. A flashing check engine light is the strictest case, and the rule is on this page above. Ford's purge-valve program names stalling at low speed, which in traffic is the risk. The owners wrote of stalls at lights and a busy intersection.

What the papers say. 🟢 Ford, to dealers, for a lit lamp with P2196 and/or P2198 and no drivability concerns: "the condition has no effect on vehicle operation or long term durability." (SSM 48957). For a failed purge valve: "stalling at low speed" (24N07). For the brake booster: "in all cases, the fundamental vehicle braking system remains functional" (13N02 S3). Chevrolet's computer paper: "may result in a no-start or stall" (18009). None prints a stop-driving instruction for the owner. Ford's booster line describes Ford's own part; it is not permission to drive on a pedal that feels wrong, and the brake rule in the triage box still applies.

The flashing-light rule is in the triage box above.

Should you buy a used car with a P2195 or P2196 history?

Ask five things. Which codes, and was the cause found? A receipt for a sensor is not proof: 44 or more of the 159 complaints say it came back. Is the car in the atlas, and was the paper done? A dealer's printout beats a seller's word. Is there a hiss or a hard pedal? On a 2010-2014 Edge or MKX, the booster program's printed dates have passed, so ask what the dealer will cover and get it in writing. Is there water, fluid or rubbed wire at the plug? On a 2018 F-150 2.7L built on or before July 12, 2018, has anyone checked the fuel rail pressure? Walk away from a history with stalls and a seller who cannot say what was done.

Clearing P2195 before an inspection

An emissions inspection generally checks that the light is off and the readiness monitors have completed; rules differ by state, so ask the station (our advice). In our understanding, clearing a code resets the monitors, and the air-fuel sensor monitor is one of them. 🟢 Toyota's 2015 campaign memo (TC15-032) for 2007 Highlander Hybrids says vehicles "may be unable to pass certain state emission testing requirements due to incomplete readiness of the required Air Fuel (A/F) sensor monitor." (F0P). The Hyundai case ended with the codes cleared and all emission readiness monitors run to complete. Do not clear and go: fix the cause, drive several normal trips and let the monitors finish (our advice).

What a shop does with P2195, checkpoint by checkpoint

The order below combines what the papers print with our advice. Ford's 3.5L GTDI paper alone goes straight from a code and a side to a new sensor.

  1. Read every stored code and the freeze-frame, and write them down. The RX-8 copy and Toyota's bulletin both start there; Land Rover's SSM72448 lists 80 codes for the same kind of fault.
  2. Look up the VIN and the engine. Ford, Chrysler, Toyota, Chevrolet, Subaru and Land Rover print model-year limits, and most add engine or build-date limits (Ford's 20-2324 adds the fuel rail pressure test, above).
  3. Check the other codes, the live data, the plug and the harness, water, air leaks and the purge valve (Toyota and Mazda for the codes and live data, Ford Transit and Land Rover for water, Toyota and Ford for the harness and the purge valve, above).
  4. Replace the sensor on a code and a bank and, where the paper for your car asks for it, a measurement, then do what the paper prints after it. Toyota: "Test drive the vehicle to confirm none of the previous DTC(s) reset." (T-SB-0001-10)

Three P2195 traps that cost owners the most

Trap 1 · Assuming the code names the guilty part. The code names the sensor the computer distrusts, not the cause; the Prius copy adds that the titles say oxygen sensor but the codes relate to the air-fuel sensor, and the papers above show that the first purchase is not always the sensor. Of the 159 complaints, 12 end at a sensor with no other cause named; 55 end at a lean engine. Ask which test shows the part is the stuck one.

Trap 2 · Clearing the code and driving on. Ford told dealers to clear the codes on the 2.7L F-150 and wait, but that was one engine, a lamp with no drivability concern and a flash on the way. Our advice: do not clear a code from a car that stalls; it hides the evidence the shop needs and resets the monitors the next inspection will ask for. Write the codes down first.

Trap 3 · Replacing the sensors on both banks, or the wrong one. Jaguar Land Rover's SSM72035, a paper on Jaguar cars that prints no P2195, gives as one possible reason that "all HO2S sensors are replaced when only one is unserviceable" (SSM72035). Toyota's bulletin says replace the sensor for the stored bank "ONLY", and Ford prints which side P2195 and P2197 mean on its 3.5L engines. Ask which bank it is.

Three P2195 situations, decoded

These are composite scenarios, not individual customers; they use only facts and price ranges already on this page.

  • A 2.7L F-150 with the light on. A smooth engine, P2196 or P2198: ask by VIN whether Ford's 21-2045 (2019-2020) or, for a 2018 truck, 20-2324 applies before you accept a sensor quote.
  • A Focus that dies after refuelling. P2196 or P2195 with P1450: ask for 24N07 and the recall check by VIN before an oxygen sensor quote. A stall means tow it first.
  • An Edge with a hiss at the pedal. It shuts off at a light, with P2195 and P2197: ask for the booster to be checked first, with a written estimate that separates it from any sensor; that program has ended. Engine shut off: the stall rule in the triage box. Hard or hissing pedal: Our advice, not a maker's: if the pedal hisses or turns hard, do not keep driving it; have the car towed. Soft or sinking pedal: the brake rule in the triage box.

The P2195 plan: 10 minutes, today, this week

Today (10 minutes). Write down the exact code list, the bank and what the car did; look for water, fluid or rubbed wire at the plug with the engine off and cool; listen for a hiss; do not clear the codes. Today (VIN). Ask a dealer or the maker's site for bulletins, programs and campaigns that name P2195 to P2198, and say your engine. This week. Pay one diagnosis, with the fuel trims and the front-sensor data written down, and try the cheapest route first. If the engine stalls, loses power, will not start, or the light is flashing, follow the triage box: tow it (it holds the one narrow exception for a flashing light).

I built PulsCar after a $380 "full diagnostic" in Phuket in 2025 led to roughly $6,000 over six months across several shops (the story is on the About page).

Sources and documents

Where a claim is marked 🟢, it rests on one of the items below; every link was opened on 20 November 2026. Claims marked ⚪ are shop-price estimates carried from the repair guides named. Third-party copies are labelled as such and not linked.

  1. Ford, 2.7L EcoBoost F-150: SSM 48789, SSM 48956, SSM 48957 (June and July 2020 per NHTSA's index; the papers print no date); TSB 20-2257 (August 7, 2020); TSB 21-2045 (February 23, 2021); TSB 18-2270 (August 30, 2018), TSB 18-2310 (October 4, 2018), TSB 20-2324 (September 17, 2020).
  2. Ford, 3.5L GTDI: TSB 17-2124 (July 11, 2017).
  3. Ford, Transit: TSB 17-0014, TSB 19-2091 (March 22, 2019).
  4. Ford, Focus and Police Interceptor purge valve: TSB 15-0034, TSB 16-0062, Customer Satisfaction Program 17M06 (October 2, 2017), Customer Satisfaction Program 24N07 (December 4, 2024).
  5. Ford, Escape and 2.0L EcoBoost: SSM 50116, SSM 50245, TSB 19-2046, SSM 48345.
  6. Ford, Edge and MKX brake booster: Program 13N02 supplement 3 (February 20, 2024).
  7. Chrysler and Ram: 25-002-14, 25-004-12, 18-012-12 Rev. A, 18-021-15 Rev. F, 18-019-15 Rev. C.
  8. Toyota: T-SB-0001-10 Rev. 1; TC15-032, campaign F0P; a 2010 Prius repair manual excerpt, "Oxygen Sensors, code troubleshooting" (file 208141_2010_Toyota_Prius_Repair_Manual_-Oxygen_Sensors-_Code_trouble_shooting.pdf, a copy hosted on a forum, read 20 November 2026; not linked, and not compared with Toyota's own site).
  9. General Motors: Service Update 18009 (January 2018). Saab: a Saab 9-5 (2011) workshop page, "DTC P0130-P0133, P2195, P2196, P2231, or P2297" (a third-party host, read 20 November 2026; not linked).
  10. Subaru: 11-183-18R (September 27, 2018).
  11. Land Rover: LTB00671NAS6 (June 27, 2016), SSM72448, SSM72035 (October 24, 2014).
  12. Audi and Porsche: Audi on-car analysis list (printed date March 25, 2025; NHTSA index date March 25, 2026); Porsche technical information 20/20 ENU 1055 (March 3, 2020; NHTSA index number 122-D4S6F-04).
  13. Mazda: the RX-8 workshop manual page "DTC P2195" (page BHE010202100W15, a third-party copy read 20 November 2026; not linked, and not compared with Mazda's own site).
  14. A repair-data publisher, not a maker: ALLDATA tech tip, Hyundai with false DTCs P0171, P0170, P2195 (January 14, 2016).
  15. PulsCar analysis of NHTSA public data, November 2026: complaints, amounts, documents, the sorting rules, how we did it; complaints received January 2015 to 4 October 2026.

What this page cannot tell you. It cannot say how often P2195 is a bad sensor: the complaint file is owners' reports, not a count of cars. It does not cover Honda, Hyundai, Kia, Nissan, Infiniti, Volkswagen, BMW, Mercedes-Benz or Suzuki papers, which did not appear for these codes or sit behind subscriptions; two manual pages were blocked. It has no shop price specific to P2195, and it cannot tell you what your car's own paper says: your VIN decides.

Prices verified November 2026 in the repair guides they are carried from (O2 sensor replacement cost, fuel injector replacement cost, fuel pump replacement cost, how much does a car diagnostic cost and the P0171 guide).

Technical documents verified November 2026.