💡 The answer in 60 seconds

A jack lifts a car; it does not hold it. Never put any part of your body under a car that a jack alone is holding up. If you must work under the car, lower it onto rated jack stands set at the car maker's support points on hard, level ground, and if you cannot do that, do not go under it. Only then does the choice of jack matter, and the makers' pages give you three numbers to compare: the rated capacity, the minimum height (can the saddle, the pad that touches the car, reach your car's lifting point?) and the maximum height (does it clear the stands?). Torin says a 3-ton jack may suit many passenger cars and some SUVs and trucks, depending on weight, lifting points and load distribution, and Torin and Sunex print in their manuals that a jack is a lifting device only. Our advice: buy three things, the jack, a matched pair of rated stands and wheel chocks. Where to lift is printed in your own owner's manual. The ASME PASE label on a jack is the maker's own statement. We did not test any jack. PulsCar sells no jacks or jack stands and no maker pays us; there is no affiliate link on this page.

This guide is a way to choose, built from what jack makers, car makers, standards bodies and workplace-safety agencies print, and it says plainly where the evidence stops. It starts with safety on purpose: a floor jack is a tool where a wrong habit can be fatal, as the cases below show.

Every figure below names its source. We read the jack makers' and government pages on 15 November 2026 and the car-maker owner's manuals on 11 and 12 November 2026. 🟢 Official marks a government or standards text; ⚪ Maker's statement marks a jack or car company's own statement about its own product or instructions, a claim or an instruction, not proof. Trade articles carry no mark. The shortlist is alphabetical by maker, not ranked, and prices appear only where a page printed one. Pages we could not read are listed near the end.

Which floor jack should I buy, and what does PulsCar have to do with the choice? Nothing at all: PulsCar sells no jacks or jack stands and takes no payment from jack makers. The useful order is the one the sources give. First the rule Torin and Sunex print in their manuals, that a jack is a lifting device and the car must be supported by jack stands before anyone goes under it. Then where your car's maker says to lift. Then the printed numbers that can be compared: rated capacity, minimum and maximum height, the weight of the jack, the safety label and the warranty. A rating such as 3 tons describes the jack, not the car, and none of the jack pages we read prints the lifting-point height of a particular car or says how much of its weight a jack takes. Your owner's manual and a tape measure close that gap.

A jack lifts a car; it does not hold it

The jack makers, the car makers and the safety agencies we read all make this point, so it comes first. A jack lifts a car; it does not hold it. Never put any part of your body under a car that a jack alone is holding up. If you must work under the car, lower it onto rated jack stands set at the car maker's support points on hard, level ground, and if you cannot do that, do not go under it.

Start with the jack makers. Torin's Garage Tools FAQ says "Floor jacks and bottle jacks are lifting devices, while jack stands are supporting devices." and, on the next line, "Never work underneath a vehicle supported only by a hydraulic jack." ⚪ Its owner's manual for the T83006C trolley jack carries the heading "THIS IS A LIFTING DEVICE ONLY!", and, in the same list, "NEVER go under a vehicle that is not supported with appropriately rated jacks stands." ⚪ Sunex's manual for its 6603GJ steel floor jack lists, among the methods to avoid hazardous situations, "This is a lifting device only. Immediately after lifting, support the vehicle with jack stands capable of sustaining the load before working on the vehicle." and, in the operating steps, prints in capitals "DO NOT CRAWL UNDER VEHICLE WHILE LIFTING VEHICLE OR PLACING OR REMOVING THE JACK STANDS!" ⚪

Then the government and safety-agency pages. Canada's occupational health and safety centre, CCOHS, says in its fact sheet on working under vehicles: "Do not get under a vehicle that is supported by a jack only - always use suitable safety stands." It adds, in the same list, "Make sure that the safety stands are in good condition and positioned properly and that the correct support pins are used in adjustable axle stands." 🟢 Washington State's Department of Labor and Industries published a hazard alert in 2010 that describes three fatal incidents in which a jack slipped or collapsed, and recommends "Support vehicles and equipment with appropriate tools such as designated lifts or jack stands, not only jacks when working under them." 🟢

The California Fatality Assessment and Control Evaluation program published case report 21CA001 about a death in 2021 in a tire shop: a vehicle slipped off a hydraulic jack while a worker was under it. The vehicle was held by two hydraulic jacks, one behind each front tire. The investigators' discussion says "Hydraulic jacks are lifting devices, not holding devices (such as jack stands)." and "Hydraulic jacks alone should not be used alone when an employee needs to perform work underneath a vehicle." 🟢 Its recommendation was that loads raised by hydraulic jacks be supported with proper cribbing or jack stands. We mention the case for one reason: it shows that adding a second jack is not the same as adding a stand.

Cars themselves ask for the same discipline. The next section puts the owner's manuals side by side.

What 21 owner's manuals print about going under a car

We read the jack sections of 21 owner's manuals from 11 car makers: Chevrolet (Equinox 2026, Silverado 1500 2025), Genesis (GV70 2023), Hyundai (Elantra 2023, Santa Fe 2023), Infiniti (QX60 2025), Mazda (CX-5 2021, MX-5 2023), Mercedes-Benz (C-Class 2022, GLE 2022, EQS 2022), MINI (Countryman 2025), Nissan (Frontier 2023, LEAF 2026, Rogue 2026), Subaru (Outback), Toyota (4Runner, Camry Hybrid, RAV4 Hybrid, Tacoma for Canada) and Volkswagen (the India-market Tiguan manual). Most of those sections describe the small jack supplied for a flat tire, not a garage jack; the next sections come back to that difference. Every one of the 21 says not to go under a raised car that the jack supports, and the wording differs in ways that matter. The grid gives one quotation per group of manuals; each manual is linked in the sources.

Chevrolet Equinox 2026 and Silverado 1500 2025: "Never get under a vehicle when it is supported only by a jack." The same pages say "Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training." ⚪
jack stands not named
Genesis GV70 2023 and Hyundai Elantra 2023: "Never place any portion of your body under a vehicle that is supported by a jack." Hyundai Santa Fe 2023 prints "Do not get under a vehicle that is supported by a jack." ⚪
jack stands not named
Infiniti QX60 2025, Nissan Frontier 2023, LEAF 2026 and Rogue 2026: "Never get under the vehicle while it is supported only by the jack. If it is necessary to work under the vehicle, support it with safety stands." ⚪
safety stands named
Mazda CX-5 2021 and MX-5 2023: "No person should place any portion of their body under a vehicle that is supported by a jack." and "Going under the vehicle while it is jacked up is dangerous as it could result in death or serious injury if the vehicle were to fall off the jack." ⚪
jack stands not named
Mercedes-Benz C-Class, GLE and EQS 2022: "Never lie under the vehicle." The manuals add that the jack is "only designed for raising and holding the vehicle for a short time while a wheel is being changed and not for maintenance work under the vehicle." ⚪
jack stands not named
MINI Countryman 2025: "When the vehicle is raised with the jack, do not lie under the vehicle and do not switch on the driveready state." ⚪
jack stands not named
Subaru Outback: "Never get under the vehicle supported only by a jack. Always use safety stands to support the vehicle." ⚪
safety stands named
Toyota 4Runner, Camry Hybrid and RAV4 Hybrid: "Do not put any part of your body under the vehicle while it is supported by the jack." and "Use a jack stand if it is necessary to get under the vehicle." The Tacoma (Canada) manual prints "Do not put any part of your body under the vehicle supported by a jack." and the same stand line. ⚪
jack stand named
Volkswagen Tiguan (India edition): says never to place any part of the body, an arm for example, underneath the vehicle if it is only supported by the jack, and in another warning "If you have to work underneath the vehicle, use suitable stands to provide extra support for the vehicle." ⚪
stands named

Read the grid for what it does and does not say. Five of the 11 makers (Nissan, Infiniti, Subaru, Toyota and Volkswagen, 10 of the 21 manuals) tell the reader what to do if work under the car is necessary, and every one of them names a stand. The other six makers (Chevrolet, Genesis, Hyundai, Mazda, Mercedes-Benz and MINI, 11 of the 21 manuals) say not to go under and name no stand in the text we read. That is a gap in what we read, not a statement that those makers allow work under a car on a jack: we read the jack passages of each manual, and the figures that show lifting points are pictures that were not in the text. The wordings differ. Chevrolet, Subaru, Volkswagen and the Nissan group say only a jack, which leaves room for a car on stands. Hyundai, Genesis, Mazda and Toyota say supported by a jack with no qualifier, and Mercedes-Benz and MINI say not to lie under the vehicle at all while it is raised on the supplied jack. The wording on this page is never softer than any of them: nobody goes under a car that only a jack is holding, and nobody uses the small jack from the trunk as a workshop tool.

Where the owner's manuals say to lift

Lifting at the wrong point is something the makers warn against: Mazda says it is dangerous, and Hyundai and Genesis say never to jack at any other position. The 21 manuals we read all point to their lifting points, in different words (Mercedes-Benz only through a figure), and none of the text we read puts a general rule above the car's own page. The grid lists the point as each maker prints it. The pictures that show where the points are on a particular car are not in the text we read, so the grid tells you what to look for in your own manual, not where to put the saddle on your car.

Chevrolet Equinox 2026: "The notches in the jack must align with the notch in the rocker pinch weld." and "The jack must not be used in any other position." Silverado 1500 2025: "If the flat tire is on the rear, position the jack under the rear axle about 5 cm (2 in) inboard of the shock absorber bracket." ⚪
pinch weld; axle; frame bracket
Genesis GV70 2023, Hyundai Elantra 2023 and Santa Fe 2023: "The jacking positions are plates welded to the frame with two notches. Never jack at any other position or part of the vehicle." ⚪
frame plates with two notches
Infiniti QX60 2025 and Nissan Frontier 2023: "The jack-up points are indicated by the notches under the frame." (Infiniti) and "Use the correct jack-up points. Never use any other part of the vehicle for jack support." Nissan Rogue 2026 and LEAF 2026: "Align the jack head between the two notches in the front or the rear as shown." ⚪
notches under the frame
Mazda CX-5 2021 and MX-5 2023: "Place the jack under the jack-up position closest to the tire being changed with the jack head squarely under the jack-up point." ⚪
jack-up position
Mercedes-Benz C-Class and GLE 2022: "The jack is designed exclusively for jacking up the vehicle at the jack support points." The point locations are in a figure titled "Position of jack support points" (also in the EQS manual). ⚪
jack support points (figure)
MINI Countryman 2025: "Insert the jack into the rectangular recess of the jacking point closest to the wheel to be changed." ⚪
rectangular recess
Subaru Outback: "Place the jack under the side sill at the front or rear jack-up point closest to the flat tire." ⚪
side sill jack-up point
Toyota 4Runner: "Front - Under the chassis frame side rail" and "Rear - Under the rear axle housing". Camry Hybrid and RAV4 Hybrid: "The jack point guides are located under the rocker panel. They indicate the jack point positions." ⚪
frame rail, axle housing, rocker
Volkswagen Tiguan (India edition): "Fit the jack only at the described jacking points. The jack claw must grip the vertical rib under the side member securely" ⚪
vertical rib under side member

Three details are worth taking from the grid. First, the points are not one place. A frame bracket and a rear axle on a pickup, a notch in a pinch weld (the folded seam along the bottom edge of the body) on a crossover, plates with two notches on a Hyundai or Genesis: the same floor jack saddle will not suit all of them, and several makers print a shape that the jack head has to match (Chevrolet's notches, Toyota's groove on the jack for the rear axle housing). Second, some makers print where not to lift. Hyundai and Genesis: "ALWAYS place the jack on the designated jacking positions on the vehicle and NEVER on the bumpers or any other part of the vehicle for jacking support." ⚪ Toyota's 4Runner manual says "When jacking up the vehicle, do not use an Automatic running board as a jack point." ⚪ Infiniti has a separate point for a vehicle with running boards: "If your vehicle is equipped with Running Boards use the Jack Point located on the front or rear mounting brackets." ⚪ Third, the floor-jack pages are brief: Toyota's Camry Hybrid and RAV4 Hybrid manuals each have a page titled "Positioning a floor jack", and the text under it is three short sentences and two pictures labelled front and rear.

Torin's jack manuals add a warning about the one part of a car that looks like a lifting point and is not: "Never use the jack on curved or tubular vehicle Bumpers, this will result in the vehicle slipping off the jack and falling, causing serious injury or death." ⚪ Both the bumper rule and the car makers' lists are examples of the same idea that Torin states generally: "Lift only on areas of the vehicle as specified by the vehicle manufacturer." ⚪ And Sunex's floor jack manual puts one reading task before any pumping: "IMPORTANT: Before attempting to raise any vehicle, check vehicle service manual for recommended lifting surfaces." ⚪

The small jack from the trunk is not a garage jack

Readers may ask whether the scissor or screw jack that came with the car is good enough for a job in the driveway. The car makers answer for their own jack, and the answers are consistent. Chevrolet: "If a jack is provided with the vehicle, it is designed only for changing a flat tire." ⚪ Toyota: "Do not use the tire jack for any purpose other than replacing tires or installing and removing tire chains." ⚪ Subaru: "The jack supplied with the vehicle is designed only for changing a tire." ⚪ Volkswagen: "The jack supplied with the vehicle is only designed for changing a wheel when one vehicle tyre is damaged and has to be replaced." ⚪ MINI is the plainest about frequency: "The jack is not designed for frequent use, e.g., changing from summer to winter tires." ⚪ A garage floor jack is a different tool for a different duty; these car makers limit their own jack to wheel and tire work.

The same manuals also say what the owner may not substitute. Mazda: "Using a jack that is not designed for your Mazda is dangerous." ⚪ Volkswagen: "Other vehicle jacks could slip out of position – this includes vehicle jacks supplied with other Volkswagen models." ⚪ Infiniti prints "Do not use the jack provided with your vehicle on other vehicles." ⚪ Mercedes-Benz's manuals say "Use only a vehicle-specific jack that has been approved by Mercedes-Benz to raise the vehicle." ⚪

Six of the 21 manuals name a floor jack or a garage jack, and Volkswagen's tells the owner what to do about other jacks. They are the car makers' own statements about a garage jack, so read them closely:

Infiniti QX60 2025, Nissan Frontier 2023 and Rogue 2026, in a do-it-yourself service procedure: "Raise and support the vehicle using a suitable floor jack and safety jack stands." and "Place the safety jack stands under the vehicle jack-up points." The steps sit under the engine oil and filter change in each manual. ⚪
floor jack plus stands
Toyota Camry Hybrid and RAV4 Hybrid: "When using a floor jack, follow the instructions in the manual provided with the jack and perform the operation safely." ⚪
follow the jack's own manual
Subaru Outback: "Contact a SUBARU dealer when jacking up the vehicle using a garage jack." ⚪
ask the dealer
Volkswagen Tiguan (India edition): "When using the breakdown set, never lift the vehicle with a jack, even if the jack is approved for the vehicle." ⚪
breakdown set: no jack

None prints a list of approved floor jacks. The Nissan, Infiniti and Toyota texts pair the floor jack with stands or with the jack's own manual, so the warnings in the manual of the jack you buy are the instructions that apply; Torin's and Sunex's are quoted on this page.

Hybrids, electric cars, air suspension and other cautions

Only one of the 21 manuals prints a caution about the battery pack when lifting. Mercedes-Benz's EQS 2022 manual says "If you do not position the jack at the designated jack support points, you could damage your vehicle and, in particular, the high-voltage battery." ⚪ The same page prints a second EQS warning, that damage can follow from a jack that is not designed for the car's support points. That is one manual and one electric car, so the right statement is narrow: if your car is electric or a plug-in hybrid, the manual page for lifting is not optional reading, and if the page shows the points only in a figure, the figure is the instruction. The other electrified manuals we read, the Nissan LEAF and the Toyota hybrids, print different cautions: Nissan LEAF, "Do not start or run the EV system while vehicle is on the jack, as it may cause the vehicle to move." ⚪ Toyota's Camry Hybrid and RAV4 Hybrid: "Do not start the hybrid system or drive the vehicle while the vehicle is supported by the jack." ⚪ The LEAF also has four covers over the jack-up points: "Four jack-up point covers are provided over the jack-up points to improve the aerodynamics." and, after the lift, "After removing the jack from the jack-up point, install the jack-up point cover." ⚪ A cover that is left off or put back wrongly is an easy thing to miss, and it is one reason to read the page.

Other cautions that a floor-jack buyer meets, each from one maker's page:

Mercedes-Benz EQS 2022, air suspension: "If the AIRMATIC system has released air when raising the vehicle, the jack can become trapped when the vehicle is lowered." ⚪
air suspension
Genesis GV70 2023, all-wheel drive: "Never start or run the engine while an AWD vehicle is raised on a jack." Hyundai Santa Fe 2023 prints the same for a 4WD vehicle. ⚪
AWD and 4WD
Volkswagen Tiguan (India edition): "Never start the engine when the vehicle is jacked up. Engine vibrations can cause the vehicle to fall off the jack." ⚪
engine off, always
MINI Countryman 2025: "Placing supports, e.g., wooden blocks or similar, under the jack may reduce its ability to bear weight because of the limited height." ⚪
no blocks under the jack
Subaru Outback: "Do not jack up the vehicle on an incline or a loose road surface." ⚪
firm, level ground

None of the car makers says what to do about a lifting point that the car does not have. The rule on this page for that case is our advice, not a maker's: if you cannot find the point in your manual, or the manual shows it only in a figure you cannot match to your car, ask a dealer or stop. Subaru's sentence about garage jacks points the same way: contact a dealer.

The next section is about the stands.

Jack stands: what the makers print, and why the jack must reach them

The car makers say little about stands; the stand makers and the jack makers say a lot, and they say it in checklists. We read two Sunex stand manuals (the 1003C, 1006C and 1012C ratcheting stands, and the 1003AJ aluminum stands) and the stand sections of the Torin and Sunex jack manuals. Read them as a buyer's checklist, not as a licence to improvise.

Sunex's ratcheting-stand manual lists among its methods to avoid hazardous situations: "Use as a matched pair only." and "Stands are to be used in matched pairs to support one end of a vehicle only. Do not simultaneously support both ends or one side of a vehicle." ⚪ The same list includes "Apply the emergency brake, put the gear shift lever in park or gear if a manual shift transmission, and chock the tires that will not be lifted off the ground." and "Consult the vehicle manufacturer for the proper frame support locations." ⚪ Setting the stands has its own line, which is the same warning the jack manual prints for lifting: "Do not crawl under vehicle when placing/removing stands." ⚪ Two more lines the owner can check by eye: "Ensure both stands are set at same height and locking pawls are fully engaging the support column's teeth." and "Check the stands for solid contact with the ground and vehicle." ⚪

What the printed specification says about size is simple. Sunex prints for the 1003C a low height of 11.5 inches and a maximum height of 17.4 inches, a base of 8 by 6.5 inches and a shipping weight for the pair of 16.1 pounds; for the aluminum 1003AJ, a minimum height of 10.6 inches, a maximum of 15.4 inches, a base diameter of 7.1 inches and a pair weight of 10 pounds. ⚪ Both are rated 3 tons. The capacity wording needs care: Sunex says "Maximum load capacity per matched pair shall not exceed the rated capacity of the individual stand." ⚪ Torin's FAQ: "Some products are rated as a pair, while others list a capacity for each individual stand." ⚪ So read the label for the words "pair" and "each".

Here is the part that connects the stands to the jack you are buying. The lowest height a stand can be set to is a printed number (11.5 inches for the Sunex 1003C), and the car's support point has to be lifted at least that high before the stand can be set under it. Matco's page for its 3 ton low-profile jack says something close to this in a marketing line: "Max lift height of 20.4" provides the necessary clearance when looking to position jack stands or when working on raised vehicles." ⚪ Torin's FAQ lists the same factors for the stands themselves: rated capacity, "Minimum Height: Confirm the stands fit beneath the vehicle after it is raised.", maximum height, the locking mechanism and the base design, and it ends with "Always follow the vehicle manufacturer's recommended support locations." ⚪ The arithmetic is ours, not a maker's: the jack's maximum height must exceed the stand's minimum height at your car's support point, with room to slide the stand in, or the car cannot be put on the stands. Nissan puts the stands under the jack-up points and Sunex says to consult the car maker for the frame support locations, so check in your manual whether the two are the same place (our advice).

Torin's manual adds a rule about stands: "DO NOT USE wood blocks or any other non-approved load sustaining devices. The manufacturer only warrants loads to be sustained by jack stands that meet current ASME standards." ⚪ Torin's FAQ gives the lowering routine: "Use the floor jack to raise the vehicle just enough to remove the load from the stands." then "Remove the jack stands from the work area, then slowly operate the jack's release control according to its manual to lower the vehicle." ⚪ The next line in the FAQ is "Never place any part of your body under the vehicle while adjusting or removing the stands." ⚪

That is why a page about floor jacks spends a section on stands: the purchase is a pair, not one tool. The two Sunex stands above are examples as printed, not a shortlist.

ASME PASE: what the label on a jack can and cannot tell you

All three jack makers whose pages we read name ASME PASE, so it deserves a plain explanation. ASME, the American Society of Mechanical Engineers, publishes PASE, the Safety Standard for Portable Automotive Service Equipment. ASME's product page says the standard applies "to the design, construction, marking, operation, maintenance, and owner or operation inspection" of a list of equipment that includes "automotive hand jacks, automotive mechanical jacks, automotive stands, automotive ramps". 🟢 The page also says "This standard has been placed on stabilized maintenance." and heads the listing "PASE - 2024". 🟢 The standard's text is sold, not free, and we did not buy or read it.

What we did read is thinner, and we say so. ASME's catalogue file for the 2014 edition (a preview of its front matter) says the edition is a "Revision, Redesignation, and Consolidation of ASME PALD-2009 and ASME ASP-2010" and lists, in its table of contents, parts titled "Hydraulic Hand Jacks", "Emergency Tire-Changing Jacks" (with the figures "Typical Scissors Jack" and "Typical Bumper Jack") and "Service Jacks" (with the figure "Typical Hydraulic Service Jacks"). 🟢 So the 2014 edition lists emergency tire-changing jacks and service jacks as separate parts, which matches what the car makers say about the jack in your trunk. An Intertek (testing laboratory) standards update notice issued 12 May 2023 gives 1 June 2024 as its effective date for the 2019 edition and lists among the changes "New requirements for Automotive and Mechanical Hydraulic Jacks" and "New requirements for Automotive Stands". For the new jack and stand sections it prints only headings, among them "Safety Markings and Messages", and says "See standard for details."

A Bosch guest blog in Vehicle Service Pros (25 May 2020) adds one caution that matters to a buyer: "A very significant point to understand about the ASME PASE Standards is they’re not required." It adds that a test for a jack "may ask manufacturers to apply a load at 150 percent of the recommended capacity and measure if the equipment still holds up, while a stand may require a similar test at 200 percent of rated capacity." That is a trade summary, not the standard, and we could not check the percentages against the text.

Now the labels. The makers' wording differs, and we print each as read:

Sunex, sales sheets for the 6603SJ and 6603GJ: "COMPLIES WITH ASME PASE-2019 SAFETY STANDARD" ⚪
2019 edition named
Sunex, owner's manuals dated 2026 (6603GJ and 6603SJ): "Complies with ASME PASE-2024 Safety Standard" ⚪
2024 edition named
Matco, product pages: "Compliant with the ASME PASE Safety Standard" (3T low-profile jack), "Compliant with ASME PASE-2019 Safety Standard" (hybrid floor jack, 3.5 ton low-profile jack) ⚪
edition sometimes not named
Torin, owner's manuals: "Meets ASME PASE safety standards." ⚪
no edition named

Two lessons. A label is a statement by the maker, and a different edition is named on a maker's older sheet and its newer manual, so read the date on the paper. And we read no test report or laboratory listing for any jack here: the page cannot tell you that a jack was tested to the standard, only that its maker says it complies or meets it. A stand with no standard named on it is something to ask about before you buy.

Capacity: what 3 tons means, and what it does not

Rated capacity is the first number on every jack, and Torin's FAQ explains it in cautious terms: "The tonnage rating indicates the maximum load the jack is designed to lift under its specified operating conditions." and "The actual load placed on the jack depends on the vehicle's weight distribution and the selected lifting point." ⚪ It tells the buyer to "Check the rated capacity displayed on your specific jack and follow the vehicle manufacturer's lifting recommendations." ⚪ On whether 3 tons is enough, the same FAQ says a 3-ton floor jack "may be suitable for many passenger vehicles and some SUVs or pickup trucks, depending on their weight, lifting points, and load distribution." and that "For heavier trucks, larger SUVs, or commercial vehicles, a higher-capacity jack may be necessary." ⚪ Sunex's and Torin's manuals share one more rule: "Do not use jack beyond its rated capacity. Do not shock Load." (Sunex) and "Do not exceed rated capacity." (Torin) ⚪ Matco's pages list a feature that backs the rule up, load-limiting and bypass valves that "prevent use beyond rated capacity and over extension of ram". ⚪ Torin's T83006C manual also lists a use limit that is worth knowing before you buy: its table prints a capacity of 3 tons for the jack alone and "2.5 TON" with the S.U.V. adapter, so an adapter can lower the rating.

The one federal rule that gives you a per-car number is the vehicle certification label. 49 CFR 567.4, the federal rule on that label, says it must be on the door-latch post, hinge pillar or door edge "next to the driver's seating position" (with fallback locations) and that it must carry the "Gross Vehicle Weight Rating" and the "Gross Axle Weight Rating", the latter for each axle. 🟢 The rule defines GVWR as a value "which shall not be less than the sum of the unloaded vehicle weight, rated cargo load, and 150 pounds times the number of the vehicle's designated seating positions." 🟢 Put plainly, and in our reading, that is a ceiling for the loaded car, set by the maker, not the weight you are lifting, and no page we read prints the weight of any particular car. For the jack, the useful arithmetic is ours: a US ton is 2,000 pounds, so a jack rated at 3 tons is rated for 6,000 pounds (check the label on the jack). A jack lifts one end, and the share of the car on that end depends on the car, which is Torin's point about weight distribution. Our advice: compare the jack's rating with the gross axle weight rating on the door label for the end you will lift, and leave a margin, because the makers' sentences all say the rating is a maximum.

Lift range: low-profile and standard, as the makers print it

Two heights decide whether a floor jack suits your car: the minimum height, which says whether the saddle will slide under the car's lifting point, and the maximum height, which says how high the car can be raised. The makers define the terms plainly. Torin's FAQ: "A low-profile floor jack features a lower minimum saddle height, allowing it to reach lifting points under vehicles with limited ground clearance." and "A standard floor jack may be suitable for vehicles with higher ground clearance." ⚪ It describes a long-reach jack as designed "to access lifting points located farther underneath a vehicle", useful for "vehicles with extended front overhangs, low ground clearance, or lifting points that are difficult to reach with shorter jacks." ⚪ Torin's buying list says of the minimum: "Minimum Height: Make sure the jack can fit underneath the manufacturer's recommended lifting point." ⚪ and for the maximum "Maximum Lifting Height: Confirm that the jack can raise the vehicle high enough for your intended maintenance." ⚪

No page we read prints the height of any car's lifting point, so the number that decides the purchase is one you measure: the distance from a flat floor to the underside of the lifting point your manual names, and then the height to which that point has to rise for your stands to fit under it. The ranges below are printed as read; each jack's own label or manual governs. Rows are alphabetical by maker.

Matco 3T low-profile jack (MFJ3TAMG): capacity 3 ton, minimum height 3.5", maximum height 20.4", product weight 81 lbs. ⚪
3.5" to 20.4"
Matco 3 ton hybrid floor jack (MHJ3TM): minimum height 4", maximum 18.5"; the page says its "63 lbs. hybrid design includes the durable strength of a steel jack in a lightweight aluminum chassis". ⚪
4" to 18.5"
Matco 3.5 ton low-profile jack (MLPJ35TM): minimum height 3.75", maximum 21.75"; the page prints the weight both as "105oz." and as 105 lbs, so we give none. ⚪
3.75" to 21.75"
Matco off-road 2-ton jack (MORJ2T): the page says its standard and V-shaped extension adapters "provide a secure lift height up to 28.5"." The page does not print the rating with the adapters fitted. ⚪
up to 28.5" with adapters
Sunex 6603AJ, 3 ton aluminum floor jack: low height 3.85", high height 19.4", net weight 55 lbs, saddle diameter 4.57". ⚪
3.85" to 19.4"
Sunex 6603GJ, 3 ton steel floor jack: minimum height 5.17", maximum 18.62", saddle diameter 4.33", product weight 73.4 lbs. ⚪
5.17" to 18.62"
Sunex 6603SJ, 3 ton steel low-profile service jack: minimum height 3.3", maximum 20.3", product weight 81.1 lbs on the sales sheet (the manual prints 81 lbs net). ⚪
3.3" to 20.3"
Torin T83006C, 3 ton S.U.V. trolley jack: 5-7/8 to 17-5/16 inches without adapter (3 ton); with the S.U.V. adapter 9-1/4 to 20-7/10 inches as printed (2.5 ton). ⚪
5-7/8" to 17-5/16"
Torin CT83502, 3-1/2 ton: 5-11/16 to 19-11/16 inches. Torin CTA82001, 2 ton: 3-3/8 to 13 inches. (Both manuals are hosted by Canadian Tire.) ⚪
two Torin models

The grid carries one lesson about the word "3-ton": the same capacity comes with a minimum height from 3.3 inches to 5.17 inches among the Sunex jacks, and 5-7/8 inches for the Torin. If your car sits low, the minimum is the number to check first; if you lift a truck or an SUV, the maximum is. Torin's own T83006C table shows the third factor, the adapter: fitted, the jack reaches higher at both ends of its range and its rating falls from 3 tons to 2.5 tons.

Build, pump and saddle: what the makers say about steel, aluminum and speed

The remaining specifications are about convenience. Torin's FAQ sums up the metals: aluminum jacks "Generally offer a lighter overall design, making them convenient for transportation, storage, and frequent repositioning." and steel jacks "Often feature heavier-duty construction and are commonly used in professional garages and workshops.", and it adds "The best choice depends on your required lifting capacity, frequency of use, and portability preferences." ⚪ The printed weights fit that picture without settling anything about strength: Sunex prints 55 pounds net for its aluminum 6603AJ, 73.4 pounds for its steel 6603GJ and 81.1 pounds for its steel low-profile 6603SJ; Matco's hybrid jack is "63 lbs." ⚪ No page we read prints a durability test.

Speed comes from the pump. Torin's FAQ says a dual-piston pump "is designed to raise the lifting arm more quickly than many conventional single-pump designs." ⚪ Sunex's sheets describe a hydraulic power unit with dual pump pistons, and Matco's low-profile page says the arm reaches maximum height "in only 6 strokes" without a load. ⚪ A quick-rise pump says nothing about stability under load.

Torin's manuals say the jack "features an overload valve bypass system to prevent jack damage and user injury." and, among its rules, "Do not adjust the safety valve." ⚪ Matco's pages list load-limiting and bypass valves. ⚪

The saddle is where the makers are strictest. Sunex's manual: "Do not use any materials that may serve as risers, spacers or extenders between the stock lifting saddle and the load." and "Do not use any adapters that replace the stock lifting saddle unless approved or supplied by the jack manufacturer." ⚪ Torin's rules: "Only attachments and/or adapters supplied by the manufacturer shall be used." and "Center load on saddle prior to lifting." ⚪ Torin's FAQ on rubber pads: "Only use pads or adapters that are compatible with the jack and suitable for the vehicle's specified lifting point." ⚪ And on the idea of gaining height with something under the jack: "Do not use loose wood blocks, bricks, or improvised materials to increase a jack's height or create an unstable lifting arrangement." ⚪ For a car in a driveway the only safe reading is the jack's own manual and your car's own manual; do not improvise a block, a spacer or an extender.

Shortlist by situation: what each maker prints

Each row is a product as the maker's own page or manual described it on 15 November 2026. The rows are alphabetical by maker inside each situation and are not ranked; in the middle group no page names the use, so the grouping there is ours by printed height; a row is not a sign that the jack is right for your car or in stock. Only three jack makers could be read in full (the others refused access or did not connect, listed near the end), so this is a short list of what we could read, not a market survey.

Low-clearance cars

Matco MFJ3TAMG, 3T low-profile jack: "LOW PROFILE. 3.5" front clearance allows for this low profile jack to be used in the most difficult of situations"; dual pistons; load-limiting and bypass valves; 45 inch two-piece handle. ⚪
3.5" to 20.4"
Sunex 6603SJ, 3 ton steel low-profile service jack: the sales sheet says its low-profile frame design and a lift range of 3.3" to 20.3" let it access hard-to-reach lift points; capacity 3 tons. ⚪
3.3" to 20.3"
Torin CTA82001, 2 ton: "Compact design allows use in confined spaces. Easily fits under low vehicles." minimum 3-3/8", maximum 13". ⚪
3-3/8" to 13"

Everyday cars and crossovers

Matco MHJ3TM, 3 ton hybrid floor jack: "Low saddle height provides access to hard-to-reach lift points"; 4" to 18.5". ⚪
4" to 18.5"
Sunex 6603AJ, 3 ton aluminum floor jack: 3.85" to 19.4"; the brochure page calls it "lightweight (55 lbs)". ⚪
3.85" to 19.4"
Sunex 6603GJ, 3 ton steel floor jack: "3-ton steel floor jack with a 5.17" to 18.62" lift range, rapid dual pump pistons, and durable construction for professional shop use." ⚪
5.17" to 18.62"

Pickups, SUVs and higher-clearance vehicles

Matco MLPJ35TM, 3.5 ton: "gives you the lift range needed to work under low clearance vehicles as well as full size SUVs and pickup trucks"; maximum 21.75". ⚪
3.75" to 21.75"
Matco MORJ2T, off-road 2-ton jack: extension adapters "provide a secure lift height up to 28.5"." The page does not print the rating with the adapters fitted. ⚪
up to 28.5" with adapters
Torin T83006C, 3 ton S.U.V. trolley jack: the manual calls it a 3 ton S.U.V. trolley jack and prints a 2.5 ton rating with the S.U.V. adapter, which lifts between 9-1/4 and 20-7/10 inches. ⚪
2.5 ton with adapter

Warranty, returns and inspection: what the papers say

The two warranty papers we read are short. Sunex's manual: "This product carries a ONE-YEAR warranty." and "Worn parts resulting from inadequate or no lubrication are not eligible for warranty consideration." ⚪ Torin's T83006C manual: "This service jack is covered under a 1-year limited warranty when used as recommended." and "This warranty does not cover damage or defects caused by improper use, careless use or abuse of the equipment." ⚪ So for the two makers whose warranty papers we read, the warranty is one year, repair or replace at the maker's option, with exclusions for misuse and, for Sunex, for lack of lubrication.

Matco's pages print a returns line, "30-Day Risk FREE return for refund or replacement", with a footnote that the offer applies to purchases on its website "excluding Toolboxes, Tool Carts, Diagnostics, Welders, Shop Equipment and shipped items weighing more than 150 pounds" and sends offline purchases to the distributor for return information. ⚪ Matco's own category path files these jacks under Shop Equipment, one of the groups the footnote excludes, so ask before you rely on the return period.

Inspection is where the makers and the workplace rules line up. Sunex: "Visual inspection should be made before each use of the jack, checking for leaking hydraulic fluid and damaged, loose or missing parts." It also says a jack subjected to an abnormal load or shock must be inspected by a manufacturer's repair facility, and "It is recommended that an annual inspection of the jack be made by a manufacturer's authorized repair facility". ⚪ Torin: "Inspect the jack carefully before each use." ⚪ The federal rule for construction employers, 29 CFR 1926.305(d)(1)(iv), sets minimum inspection intervals: "For constant or intermittent use at one locality, once every 6 months" and, for a jack subjected to abnormal load or shock, "immediately before and immediately thereafter." 🟢 and 1926.305(d)(1)(vi) adds "Jacks which are out of order shall be tagged accordingly, and shall not be used until repairs are made." 🟢 Those intervals bind employers, not homeowners.

Setting up: the floor, the chocks and the habits that come with a jack

The jack makers print a short list of habits, and they agree with each other. On the floor: Torin: "Use only on hard, level surfaces, with less than 3 degrees of slope." ⚪ Sunex: "Use only on a hard level surface capable of supporting load and free from obstructions so the jack is free to reposition itself during lifting and lowering operations." ⚪ Torin's FAQ names the surfaces to avoid: "Gravel, soft asphalt, dirt, and uneven surfaces may allow the jack to shift, sink, or become unstable." ⚪ CCOHS adds a position rule that is easy to miss: "Do not position yourself where you could be pinned between the operating handle and the wall if the vehicle or jack moves unintentionally." 🟢

On stopping the car from moving: Torin: "Use wheel chocks or other blocking device on opposing wheels before using jack." ⚪ CCOHS: "Use chocks in front and back of the wheel that are on the diagonal from the wheel that will be raised (e.g., if jacking up the right, front wheel, use the chocks on the left, rear wheel)." and "Shift the vehicle with an automatic transmission to a park or low gear if it has a standard transmission, and apply the parking brake." 🟢 The car makers' manuals say the same in their own words for their own jacks. Mazda: "Block the wheel diagonally opposite the flat tire." Nissan: "Place suitable blocks at both the front and back of the wheel diagonally opposite the flat tire to prevent the vehicle from moving when it is jacked up." ⚪

On the car and the people around it: Torin: "Do not move or dolly the vehicle while on the jack." and "Do not allow anyone in the vehicle while the jack is in use." ⚪ Torin also says "When the lift is being lowered, make sure everyone is standing at least six feet away." ⚪ and "Wear ANSI-approved safety glasses and heavy-duty work gloves during use." ⚪ Sunex: "Always lower the jack slowly and carefully." ⚪ All of these apply while a car is on a jack; the stand makers print their own list (section above), which is why the stand section comes before any job.

If your job is a wheel-off job such as a tire rotation, our tire rotation cost guide covers what a shop charges and what the makers print about rotation; this page covers only the lifting. And if you plan the brake or oil job yourself, the steps of those jobs are in our how to change brake pads guide and how to change oil guide, which carry their own rule about stands.

Prices: what any page printed

Only Matco's pages printed a price. Read on 15 November 2026 on matcotools.com: the 3T low-profile jack (MFJ3TAMG) $359.95, the 3.5 ton low-profile jack (MLPJ35TM) $579.95, the off-road 2-ton jack (MORJ2T) $599.95 and the 3 ton hybrid floor jack (MHJ3TM) $609.95. ⚪ The Sunex and Torin pages and manuals we read printed no price, and the retailer sites that carry other jacks refused access, so we print nothing about their prices. A price on a page can change, and Matco sends offline purchases to its distributor, so treat the figures as a dated reading, not a quote.

Best floor jack brands: why this page ranks none

Which floor jack brand is the best, and does PulsCar recommend one? PulsCar does not rank brands, because it sells no jacks or jack stands, tested none, and the sources we read do not support a ranking either. The makers describe their own jacks in their own words, the standard that would let a buyer compare them is paid and we did not read it, and we read no independent test that names jacks and prints results. What a reader can check are the printed numbers and the printed rules: the rated capacity, the minimum and maximum height, the weight, the safety label and the edition it names, the warranty terms and whether the paper in the box says to use jack stands. Any list that puts one maker first, without a named test behind it, is an opinion. If a shop offers a choice, ask for the model's manual before you pay and read its warnings.

The traps: three ways a floor jack purchase goes wrong

Trap one: treating the jack as the support. The situation: the car is up, the jack is under it, and a quick look underneath seems harmless. What is real: Torin and Sunex say the jack is a lifting device only, all 21 manuals say not to go under a car on the jack, and California's investigators described a case in which a car sat on two hydraulic jacks. The price: a car that falls with a person under it. The defense: the stands, every time, and the rule printed above.

Trap two: buying by the tonnage alone. The situation: a 3-ton jack looks like enough for any car. What is real: Torin says the actual load depends on weight distribution and the lifting point, the rating changes with an adapter on its own T83006C, and the printed minimum height of 3-ton jacks runs from 3.3 to 5.17 inches among the Sunex models alone. The price: a jack that cannot reach the point, or a car that cannot be raised high enough for the stands. The defense: measure the point, read the maximum height against the stand's minimum height, and check the label.

Trap three: improvising. The situation: a low car, a soft driveway, a lifting point that the jack cannot reach. What is real: Torin says not to use wood blocks, bricks or improvised materials to gain height, Sunex says no spacers or extenders between saddle and load, MINI says no blocks under the jack, Subaru says not to jack on a loose surface, and Torin says never to use its jack on curved or tubular bumpers. The price: a jack that slips or sinks. The defense: pick the jack for the car, set the car on firm ground, use the point the manual names, and stop and ask a dealer (our advice) when the manual does not name one.

Three typical situations

These are composite scenarios, not individual customers; each is built only from facts printed in the sections above.

The owner of a low sedan who wants to do an oil change. The questions are the minimum height and the manual's points. The sedan's lifting point sits low, so the buyer measures it and compares it with the printed minimum heights, which run from 3.3 inches to 5-7/8 inches on the jacks above without adapters. The decision is a jack whose minimum is below the measured height, plus stands the jack can lift above.

The owner of a pickup with a high lifting point. The questions are the maximum height and the capacity. Torin says heavier trucks may need a higher-capacity jack, and an adapter can raise the height and lower the rating. The decision is to read the printed maximum and rating together, check the axle rating on the label, and buy stands tall enough for the support point.

The owner of an electric car or a plug-in hybrid. One manual we read warns about the high-voltage battery if the jack is not at the designated support points, and the Toyota hybrid manuals have a separate floor-jack page. The decision is to read that page before buying, and, our advice, to ask the dealer if the points are shown only in a figure the owner cannot match to the car.

What this page cannot tell you

We tested no jack, so nothing here says that one lifts faster, lasts longer or is more stable than another. We did not read the text of ASME PASE and read no test report for any jack. We read three jack makers' pages in full: Matco, Sunex and Torin. Harbor Freight, Home Depot, Snap-on, JEGS, Powerbuilt, Mac Tools, OTC and others refused access, returned an error or did not connect, and Arcan and Hein-Werner did not connect, so the shortlist is incomplete by design. The car-maker material is the jack passages of 21 manuals; the figures that show lifting points are not in the text, the 4Runner, Camry Hybrid, RAV4 Hybrid, Tacoma, Outback and Tiguan passages print no model year, and the Tiguan manual is the India-market edition. We read no CPSC recall list and the NIOSH investigation we found would not load, so we state no accident or recall counts.

Can PulsCar help me choose a floor jack, or tell me whether my car is safe on one? No. PulsCar sells no jacks or jack stands and no maker pays us; there is no affiliate link on this page. A choice between two jacks is settled by what is printed on the label and in the manual that comes with each: the rated capacity, the minimum and maximum height, the safety label and the edition it names, the warranty, and the instruction to use jack stands. Whether it is safe to go under a car has one answer for every car and every jack, and it is the full wording in the shaded box at the top of this page. If a number or a lifting point is not printed in the paper you have, your owner's manual and the dealer are the next places to look.

Your action plan: before you shop, at home, after

Before you shop. This plan is our advice, built on what the makers above print. Open your owner's manual to the jack and lifting-point pages and note where it says to lift and whether it mentions a floor jack or a dealer. Find the certification label by the driver's door and read the axle ratings. Measure the height of the lifting point from a flat floor. Buy three things: the jack, a matched pair of stands rated for the end you lift (read "pair" or "each" on the label) whose lowest setting your jack can exceed, and wheel chocks; Torin also names safety glasses and gloves. Then compare jacks by rated capacity, minimum and maximum height, adapter ratings, the safety label and the edition it names, and the warranty terms. Ask for the manual before you pay.

At home. Hard, level ground only. Chock the wheels that stay down, set the parking brake, put nobody in the car, lift only at the manual's point, and no blocks or spacers. A jack lifts a car; it does not hold it. Never put any part of your body under a car that a jack alone is holding up. If you must work under the car, lower it onto rated jack stands set at the car maker's support points on hard, level ground, and if you cannot do that, do not go under it. One pair holds one end only; set both stands at the same height and seated, lower the car slowly, check that it is stable (Sunex: if it is not, lift it off the stands and reposition them), and stay out from under it while you set and remove the stands.

After. Inspect the jack and the stands before each use, do not use one that leaks or is damaged, store them as their manuals say, and have a repair facility inspect a jack that has been shocked or taken past its rating. The steps of the jobs themselves are in our how to change brake pads guide and how to change oil guide.

Sources and documents

Each jack-maker and government page below was read on 15 November 2026; the car-maker manuals were read on 11 and 12 November 2026 (dates in the saved texts). Marks: 🟢 government or standards text; ⚪ a jack or car company's own statement. Trade pages are named by publisher and date.

  1. 🟢 ASME, PASE, Safety Standard for Portable Automotive Service Equipment (product page; scope and status); ASME, PASE-2014 catalogue preview (front matter and contents)
  2. Intertek, standards update notice for ASME PASE:2019 (a testing laboratory's notice, issued 12 May 2023); Vehicle Service Pros, Bosch guest blog, ASME PASE-2019 Standards: What do technicians need to know? (25 May 2020)
  3. 🟢 OSHA, 29 CFR 1926.305, Jacks; CCOHS, Garages: Working Under Vehicles (revised 23 April 2024); Washington L&I, Hazard Alert: Crushing Hazards to Workers Under Vehicles (10 July 2010); California FACE, Case Report 21CA001
  4. 🟢 49 CFR 567.4 (certification label)
  5. ⚪ Torin: Garage Tools FAQs; owner's manuals for the T83006C, CTA82001 and CT83502
  6. ⚪ Sunex: sales sheets for the 6603SJ and 6603GJ; the brochures page and manuals page; manuals for the 6603GJ, 6603SJ and 6603AJ, and the stand manuals for the 1003C, 1006C and 1012C and the 1003AJ
  7. ⚪ Matco Tools: jacks listing, MFJ3TAMG, MHJ3TM, MLPJ35TM, MORJ2T
  8. ⚪ Owner's manuals: Chevrolet Equinox 2026 and Silverado 1500 2025; Genesis GV70 2023; Hyundai Elantra 2023 and Santa Fe 2023; Infiniti QX60 2025; Mazda CX-5 2021 and MX-5 2023
  9. ⚪ Owner's manuals: Mercedes-Benz C-Class 2022, EQS 2022 and GLE 2022; MINI Countryman 2025; Nissan Frontier 2023, LEAF 2026 and Rogue 2026; Subaru Outback; Toyota 4Runner, Camry Hybrid, RAV4 Hybrid and Tacoma (Canada); Volkswagen Tiguan (India edition)
  10. What we could not read, and so did not quote: Harbor Freight (Pittsburgh and Daytona), Home Depot (Husky), Snap-on, JEGS, Powerbuilt, Mac Tools, the Torin and Sunex product pages (the PDFs above were read instead), OTC (its product pages returned 404), Performance Tool (Wilmar; page text empty), Arcan, Hein-Werner, the CPSC recall pages, the NIOSH fatality investigation report, the ANSI web store and the text of ASME PASE itself

Prices verified: only Matco's pages printed jack prices, read 15 November 2026 · Technical documents verified: 15 November 2026 (car-maker manuals 11 and 12 November 2026) · Reviewed quarterly

Saw a jack, a rating or a figure that differs from this page? Email [email protected] with the model and the source.