💡 The answer in 60 seconds

No car maker whose papers we read recommends an engine flush, and three of them say it is not recommended. GM's service bulletin says it does not endorse or recommend engine crankcase flushing for any of its gasoline engines, and that resulting damage is not covered by the new vehicle warranty. Kia's bulletin names flushing engine oil among the services it does not recommend, and American Honda's statement for Acura says there is no reason to perform it as maintenance. Nissan, Infiniti and Subaru advise against aftermarket flushing systems in general; Hyundai, Mercedes-Benz and MINI say not to use additives in the engine oil, and Mazda says extra additives are not recommended in its turbo instructions. Some flush makers say their products are safe or seal-friendly when the label is followed, and their labels disagree with one another on time, dose and whether to drive. If you want to compare products anyway, the shortlist section lists what each maker prints, alphabetically, with no ranking. If the oil pressure warning light comes on, stop the vehicle safely as soon as possible, switch the engine off and have the car towed; do not keep driving to see whether it goes out. We did not test any engine flush. PulsCar sells no engine flush or oil additive and no oil brand pays us; there is no affiliate link on this page.

This guide is a way to decide, built from what car makers, oil makers and product makers print, and it says plainly where the evidence stops. Every statement below names its source and, where the source printed one, its date. We read the product pages, the bulletins and the government pages on 15 November 2026; most owner's manual pages were read on 11 and 12 November 2026, and the Sources list says which is which (the Castrol US and API pages were also read on 11 November). ⚪ Maker's statement marks a car, oil or product company's own words about its own policy or product, which is a claim, not proof; 🟢 Official marks a government text. Articles from trade and consumer publications carry no mark and are named by publisher and date. Product lines are listed alphabetically by maker, not ranked, and no flush maker's or shop's page we read printed a price, so this page prints none; our oil change cost guide is where the money question lives. Pages we could not read are listed near the end.

Which engine flush should I buy, and does PulsCar have a view on which one? PulsCar has none, because it sells no engine flush or oil additive, takes no payment from any oil or additive brand, and tested no product. The useful order is the one the documents give. First, what your car's maker prints about additives and flushing; ten of the thirteen car brands we read print something, and none recommends a flush. Second, what a product's own label says about time, dose and whether the engine may be driven, since the labels differ. Third, whether your situation is one a label or a maker document actually addresses. Where no document speaks, this page says so instead of filling the gap. The product pages are claims by the sellers, so they sit beside the car makers' papers on this page, not above them.

What an engine flush is, and what it is not

The product pages describe the same basic idea in slightly different words. Berryman, a maker of automotive chemicals, defines it on its blog as "an aftermarket chemical additive that is meant to clean out accumulated deposits, sludge, and other debris in your engine." ⚪ Liqui Moly calls its product a "Cleaning fluid for clearing the engine interior of troublesome deposits" that brings residues into suspension and "removes these from the oil circuit during the next oil change." ⚪ Motor Medic describes its Motor Flush as "a proprietary blend of solvents and detergents in a petroleum carrier fluid." ⚪ Whatever the formula, the common pattern on these pages is: a bottle goes into the old oil shortly before an oil change, the engine idles for a stated time, and then the oil is replaced.

Five neighbouring things are easy to confuse with it, and the documents keep them apart.

A flush is not an oil change. The oil change drains the old oil, replaces the filter and refills with the oil your manual specifies; our how to change oil guide has the steps. The flush products on these pages are an extra step before it, and every label we read says the oil must still be changed afterwards.

A flush is not an oil additive that stays in. Some products are meant to remain in the crankcase. Sea Foam's Motor Treatment page says it is "safe to leave in the oil for the entire interval," and Lucas Oil's Complete Engine Treatment page gives "Add 1 ounce only per quart of engine oil" with the words "May be added with oil change or between oil changes." ⚪ These are sold as treatments, not flushes, but the car makers' additive statements arguably apply to them.

A flush is not a different kind of motor oil. Valvoline's shop blog, dated 11 August 2026, says that for an engine flush "separate additives are poured in before an oil change and run for a few minutes" and adds that they "are aggressive and not always beneficial to high-mileage engines," while its Restore & Protect motor oil is "an actual motor oil, not an additive." ⚪ That is a Valvoline claim about its own product and about its competitors' category, so treat it as such.

A flush is not a machine service on other systems. Transmission, coolant, brake and power-steering flushes are separate services with their own makers' statements; our transmission flush cost guide covers the transmission one. Ram's owner's manual page on transmission additives, for example, says "Do not use chemical flushes in your transmission as the chemicals can damage your transmission components." ⚪ That sentence is about the transmission, and we do not stretch it to the engine.

A flush is not a fuel-system cleaner. Fuel additives go in the tank and have their own manual sections; this page is about the crankcase.

One more definition comes from the shop side. The Jiffy Lube Ontario engine-services page, a Canadian page, lists "Engine flush – OSC (Oil System Cleaner)" and says it will "Remove buildup and deposits from inside the engine with a flush designed to help restore efficiency and improve overall operation." ⚪ It adds that the service is "typically recommended when deposits begin to affect performance or as part of certain maintenance schedules." Which schedule that refers to is not stated on the page we read, and the page prints no price.

The question first: does any car maker recommend an engine flush?

The short answer from the documents is no. We read printed statements from thirteen car brands: GM (Chevrolet), Kia, Hyundai, Genesis, Honda (through American Honda's statement for Acura and a Honda manual), Nissan, Infiniti, Subaru, Mazda, Mercedes-Benz, MINI, Toyota and Ram. None says to flush an engine. Ten print something against additives in the oil or against flushing; Toyota and Genesis print nothing about either in the manual text we searched, and the Ram page we read is about the transmission. A silence is not an approval, and it is not a ban either: it means those manuals did not address the question in any place we could find.

The ten that speak fall into three groups, and the difference between the groups matters:

  • Engine flushing named and advised against: GM, Kia and American Honda.
  • Aftermarket flushing systems advised against in general maintenance notes, without naming the engine: Nissan, Infiniti and Subaru.
  • Additives in the engine oil advised against: Hyundai, Mercedes-Benz and MINI (not to use them), and Mazda (extra additives "NOT recommended" in the turbocharger instructions), as well as GM, Kia, Honda, Nissan and Infiniti, whose additive statements sit beside the flush statements above.

A flush product is, by the product makers' own descriptions, a chemical added to the engine oil, so the no-additive statements arguably include it. The manuals do not say so, though, and we mark that step as our reading. What follows gives each maker's words, so you can read the ones for your brand.

What the makers print, side by side

The grid gives each maker's statement as printed. Owner's manuals are quoted from the model years we read; a different model year or engine may print something else, and your own manual is the document that applies to your car. Bulletins are written for dealers; the one from Kia is dated November 2012 and the one from GM October 2024, and we did not find whether either has been superseded.

GM, Chevrolet 2025 Silverado 1500 and 2026 Equinox manuals, under the heading Engine Oil Additives/Engine Oil Flushes: "Do not add anything to the oil." And: "Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty." ⚪
Additives and flushes: no
GM service bulletin 04-06-01-029K, October 2024 (2025 and prior gasoline engines): "General Motors Corporation does not endorse or recommend engine crankcase flushing for any of its gasoline engines." ⚪
Flushing: not endorsed
Kia technical service bulletin 058, November 2012: lists "Flushes/Additives/Conditioners for:" engine oil among non-recommended services. ⚪
Flushes: not recommended
Kia 2024 SK3 web manual, maintenance schedule: "Never add any additives to the engine oil." ⚪
Additives: never
American Honda position statement for Acura, revised March 2019 (copy hosted by I-CAR): "Engine flushing: This procedure is not recommended by American Honda, as there is no reason to perform engine oil system flushing as a maintenance procedure." ⚪
Flushing: not recommended
Hyundai 2024 CN7, 2025 NX4 and 2026 LX3 web manuals: "Never add any additives to the engine oil." ⚪
Additives: never
Nissan 2023 Frontier and 2026 Rogue manuals, general maintenance notes: "NISSAN does not advocate the use of non-OEM approved aftermarket flushing systems and strongly advises against performing these services on a NISSAN product." Separately: "NISSAN does not recommend the use of oil additives." ⚪
Flushing systems and additives: no
Infiniti 2025 QX60 manual: the same two statements with INFINITI's name. ⚪
Flushing systems and additives: no
Subaru owner's manuals MSA5M2208A and MSA5M2403A, maintenance precautions: "SUBARU does not endorse the use of non-SUBARU approved flushing systems and strongly advises against performing these services on a SUBARU vehicle." ⚪
Flushing systems: advised against
Mazda 2021 CX-5 and 2025 CX-90 manuals, turbocharger instructions: "Use only recommended engine oil." "Extra additives are NOT recommended." ⚪
Extra additives: not recommended
Mercedes-Benz 2022 C-Class and GLE manuals: "Do not use additives." ⚪
Additives: no
MINI 2025 Countryman manual: "Oil additives can damage the engine." And: "Do not use oil additives." ⚪
Additives: no
Toyota 2021 RAV4 Hybrid and 2015 4Runner manuals; Genesis 2023 GV70 manual: no sentence about engine oil additives or engine flushes in the text we searched. Genesis prints detailed fuel-additive rules only.
Silent

Three observations from the grid. First, the fullest wording comes from the makers that wrote a bulletin for their dealers rather than a manual line: GM and Kia both say in those bulletins that flushing is not recommended, and both add that resulting damage would not be covered. Second, the manual lines are short and general; where one gives a reason, it is a single clause. Third, the Nissan, Infiniti and Subaru statements sit among general notes about maintenance, not under the engine oil heading, so they say aftermarket flushing systems are not endorsed, and we cannot tell from the pages whether the writers had the engine crankcase in mind.

GM's bulletin: the fullest car-maker statement we found

The most detailed paper comes from General Motors. Its service bulletin 04-06-01-029K, titled "Unscheduled Supplemental Services (Including Flushing Services and Additives) and Proper use of GM Simplified Maintenance Schedules," is dated October 2024 and covers "2025 and Prior GM Passenger Cars and Trucks with Gasoline Engines." It is a NHTSA-hosted dealer bulletin, written to tell dealerships what to sell and not to sell, and its last page says it is written for professional technicians, not do-it-yourselfers. ⚪

Its opening premise is about parts that come back from the field. GM writes that service departments "merchandise supplemental services and fluids to customers indicating that these 'flushes' have a positive effect on durability of the component part," and then: "analyses of returned parts that have been exposed to these aftermarket 'flushes' show indications of potential damage and shortened durability." ⚪ The bulletin does not publish the analyses, so what we have is GM's statement of its conclusion, not the data behind it.

The paragraph that matters for this page is headed Engine Crankcase Flushing: "General Motors Corporation does not endorse or recommend engine crankcase flushing for any of its gasoline engines. Analysis of some of the aftermarket materials used for crankcase flushing indicate incompatibility with GM engine components and the potential for damage to some engine seals and bearings. Damage to engine components resulting from crankcase flushing IS NOT COVERED under the terms of the New Vehicle Warranty." ⚪ Three details are worth reading closely. The wording is "some of the aftermarket materials," not all of them. The named risk is "engine seals and bearings," and the word is "potential." And the scope is gasoline engines; the bulletin says nothing about GM diesels.

The next heading, Subsystem Flushing, is about other systems. GM says flushing of air conditioning lines, radiators, transmission coolers and power steering systems are "recognized practices to be performed after catastrophic failures or extreme corrosion when encountered in radiators," and that "This practice is not required or recommended for normal service operations." ⚪ That sentence is not about the engine, and it is the only place the bulletin allows a flush at all, after a failure, for other systems. The bulletin then says external transmission fluid exchange or flush machines are not recommended, and our transmission flush cost guide is where that belongs.

One more line shows how GM frames exceptions. The bulletin says that if GM determines a specific model or powertrain needs supplemental service, "GM will issue an Authorized Service Document with detailed service procedures that will identify any machine, tool or chemical required to conduct proper vehicle servicing." ⚪ In other words, GM does not rule out that a flush or a chemical could one day be specified for a particular engine; it says that it would publish the procedure, and that is the route GM describes. We did not find such a document for any engine.

The same paragraph is old. NHTSA's library holds earlier revisions of the bulletin family with the identical engine crankcase paragraph: 12-06-01-008A, a GM of Canada dealer bulletin dated October 2012 for 2013 and prior vehicles; 04-06-01-029H, February 2016; and 04-06-01-029I, September 2017. The Canadian bulletin adds a sentence the 2024 text does not repeat: "GM vehicles under normal usage do not require any additional procedures or additives beyond what is advised under the Owner's Manual maintenance schedules or the current GM Goodwrench Maintenance Schedules." ⚪

GM's owner's manuals carry the same message in two sentences. Both the 2025 Silverado 1500 and 2026 Equinox manuals have a heading Engine Oil Additives/Engine Oil Flushes, with "Do not add anything to the oil. The recommended oils meeting the dexos specification are all that is needed for good performance and engine protection" and "Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty." ⚪ The Silverado manual writes the specification as dexos1. Our what oil does my car take guide has the oil specification side.

Kia's bulletin, and the Kia and Hyundai manuals

Kia's technical service bulletin 058, dated November 2012 and addressed to all models, is titled "Services and Products Not Recommended by Kia." It is a NHTSA-hosted dealer bulletin of two pages. Its opening paragraph states the reason in dealer terms: "Providing aftermarket additives/conditioners and products or services that are not recommended by Kia, including flushing lubricating oil and hydraulic fluid systems, increases vehicle maintenance expenses and overall cost of ownership." ⚪ That is a cost argument, stated as one; the paragraph continues that these services can possibly reduce "your dealer's long-term opportunities to perform required vehicle maintenance." ⚪

Item 3 of the bulletin is the one about the crankcase. Under the heading "Flushes/Additives/Conditioners for:" it lists Engine Oil, Transmission Fluid and Power Steering Fluid, and says they "May cause and/or contribute to component failures and any expense to repair those components, following such non-recommended flushes/additives, would not be covered by the Kia warranty." ⚪ Then comes the reason Kia gives: "Today's lubricating oils and Automatic Transmission Fluids are engineered to provide full protection in between the Kia recommended oil changes and do not require additives." ⚪

Two other items in the same bulletin help in reading it. Item 1 says Kia's owner's manual identifies "Normal" and "Severe" maintenance schedules and that "Recommending oil changes or other maintenance or preventative services at more frequent intervals is not necessary and increases the cost of Kia ownership." ⚪ Item 2 is about fuel: it says induction cleaning and flushing is not a Kia recommended procedure, and it names a fuel-tank product, TECHRON Concentrate Plus Fuel System Cleaner, as Kia-approved "if TOP TIER Detergent Gasoline is not available." ⚪ So Kia is not against every chemical cleaner; it names one for the fuel system and none for the crankcase.

Kia's current web manual says the same in a line. The 2024 SK3 manual's maintenance schedule page reads "Never add any additives to the engine oil. Engine oil additives can change the properties of engine oil and may cause serious engine failure." ⚪ Hyundai's 2024 CN7 and 2026 LX3 web manuals print the identical sentence, and the 2025 NX4 manual's page on checking the oil says "Never add any additives to the engine oil. Engine oil additives can change its properties and may cause engine failure." ⚪ The 2023 Elantra and Genesis GV70 PDF manuals use the word additive for fuel only, and we found no engine-oil additive sentence in them, so the line appears in the web manuals and not in those PDFs.

American Honda's statement

American Honda issued a position statement titled "Use of additives, fluids, and flushes in service maintenance on Acura vehicles," dated 28 February 2019 and revised March 2019. We read the copy hosted by I-CAR; we did not find the statement on a Honda or Acura site. It is addressed to Acura vehicles, not Honda ones, so for a Honda it is evidence of the company's position, not a printed rule for that car. ⚪

It lists procedures that American Honda "either does not recommend or generally considers unnecessary for Acura vehicles operating under normal conditions (with limited exceptions)." Two entries are about the engine: "Using oil additives: Your vehicle does not require oil additives. In fact, they may adversely affect the engine performance and durability." And: "Engine flushing: This procedure is not recommended by American Honda, as there is no reason to perform engine oil system flushing as a maintenance procedure." ⚪ A third entry is about frequency: "Oil changes should be performed in accordance with maintenance minder and the Acura owner's manual." It adds that "Only a relatively small percentage of Acura owners routinely operate their vehicles under severe maintenance conditions which might necessitate more frequent changes than are typically recommended." ⚪

The statement closes with its own purpose: following the recommendations in the owner's manual and maintenance minder "may help avoid the expense and inconvenience often associated with unnecessary services and products." ⚪ The same document also says fuel injection cleaning and flushing, power steering flushing and (with rare exceptions) transmission and cooling system flushing are not recommended or not necessary. It prints no warranty wording.

Honda's own 2012 Canadian manual PDF, read from honda.ca, carries the same sentence under the heading Engine Oil Additives, "Your vehicle does not require oil additives. In fact, they may adversely affect the engine performance and durability," which makes it a first-party Honda source for the additive point. It has no engine flush sentence in the text we searched, and its other additive passages concern fuel, coolant and transmission fluid. A 2023 Civic maintenance section that we read only as a forum-hosted copy has the same sentence. ⚪

What "not covered" means in each maker's words

Three makers tie their position to the warranty in writing, and they do it differently:

GM: damage "IS NOT COVERED under the terms of the New Vehicle Warranty" (bulletin) and "could cause engine damage not covered by the vehicle warranty" (manuals). The condition is the flushing itself. ⚪
Flushing named
Kia: failures following non-recommended flushes or additives "would not be covered by the Kia warranty." The condition is that the repair follows such a flush. ⚪
Flush or additive named
Subaru: "SUBARU warranties do not cover any part of the vehicle which is damaged by adding or applying chemicals and/or solvents other than those approved or recommended by SUBARU." The condition is chemicals not approved by Subaru. ⚪
Any unapproved chemical
Nissan and Infiniti: say only that the chemicals or solvents many aftermarket flushing systems use have not been "validated" by the maker. No warranty sentence in the passage. ⚪
No warranty wording
Honda (Acura statement), Hyundai, Mazda, Mercedes-Benz, MINI: print recommendations or warnings against additives; none of the pages we read says what happens to a claim. ⚪
Silent on claims

Federal law frames what a warranty can and cannot say. The Federal Trade Commission's rule on prohibited tying, 16 CFR 700.10, says a warrantor cannot "condition the continued validity of a warranty on the use of only authorized repair service and/or authorized replacement parts for non-warranty service and maintenance," and explains that "a warrantor cannot, as a matter of law, avoid liability under a written warranty where a defect is unrelated to the use by a consumer of 'unauthorized' articles or service." 🟢 Read together with the makers' statements, the picture is: a maker cannot void a warranty just because you used a part or service from another company, and a maker can say that damage caused by a particular service is not covered. Which side a given engine failure falls on is a question of cause that this page cannot answer, and nothing here is legal advice. Our advice: keep the work order for any flush and the receipts for your oil changes.

What silence means: Toyota, Genesis, Ram and the Ford pages we could not read

Toyota's 2021 RAV4 Hybrid manual and its 2015 4Runner manual, which we searched for the words additive and flush, use additive only for the engine coolant (do not use any coolant additive) and for the fuel-system detergent program, and flush only for first aid and camera cleaning. We found no sentence about engine oil additives or engine flushes. Genesis's 2023 GV70 manual says what to do about fuel additives at length and says nothing we could find about the crankcase. A manual that stays silent does not approve a flush; it also does not warn against one, and a shop that says Toyota recommends it is not quoting anything we could find in those manuals.

Ram's owner's manual is the other case. The 2022 Ram 2500/3500 page headed Special Additives says "The manufacturer strongly recommends against using any special additives in the transmission," and "Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty." ⚪ The page is in the automatic transmission section. The engine-oil selection page for the same truck, which we also read, has no additive statement. We did not read owner's manuals for Ford, Jeep, Chrysler, Dodge, Volkswagen, Volvo, BMW or Lexus, so they are not in the grid, and Ford's support page on additives and flushes refused our request. A news piece or an article that quotes Ford or Honda on flushing is not something we could check against the makers' own pages, and we have not repeated those lines.

What the oil makers say, and where they split

Oil companies sell both sides of this question, so their pages are claims to be read next to the car makers' statements, not tie-breakers. Two of them, Valvoline and Castrol, say different things.

Valvoline publishes two pages that point in different directions. Its global site's page "Engine Flush - What Is It and Should You Use It?" says that "With extended oil change intervals, tighter tolerance of modern engine design and today's severe driving conditions being the 'norm,' many vehicles are at risk of sludge formation," and presents its Complete Oil System Cleaner as "designed to dissolve and remove sludge from engines." ⚪ Its shop blog, dated 11 August 2026, says "The most effective way to remove engine sludge is to switch to a high-detergent motor oil or one specifically formulated to remove engine deposits," that with its Restore & Protect oil there is "no separate flush product required," and that an engine flush uses additives that "are aggressive and not always beneficial to high-mileage engines." ⚪ Both pages are Valvoline marketing. Reading them together, the company sells a system cleaner on one page and describes the additives used in an engine flush as aggressive on another, and the blog's product claim carries a footnote about the test it rests on (an adapted Sequence IIIH test, with four or more consecutive oil changes). We cannot say which page represents Valvoline's view in the United States.

Castrol's US page "What is motor oil?" describes what the additives already in the oil do. Under the heading "Are engine oil additives necessary?" it says the additive package protects the engine in many ways and lists among them "Prevent the formation of sludge and varnish on metal surfaces such as the oil pan, rocker covers and screens." ⚪ Castrol's Australian product page lists Engine Flush Petrol and Diesel and says it is "Recommended for use in automotive petrol engines as part of routine oil changes." ⚪ The two Castrol pages come from different regions and do not address each other; the Australian page is not a US product page, and we did not see a US Castrol flush page.

AMSOIL's pages refused our request (403), and the Mobil 1 and Pennzoil addresses we tried either refused us or did not exist, so none of them is quoted here. The American Petroleum Institute engine oil page we read, which describes the licensing of the oil quality marks, says nothing about aftermarket flushes.

What the product pages claim and warn, maker by maker

Each row below gives what the maker's own page prints on 15 November 2026: its claim in its words, its directions and its warning. The order is alphabetical, not a ranking. Region labels matter: Champion Lubes' article sits on a US site, and Berryman, Motor Medic, Sea Foam and Lucas print US units (quarts and ounces) but no country; the others are British, Australian or international pages, and their products may not be sold, or labelled the same way, in your country.

Berryman Oil Change Flush, maker's blog (undated): "gently cleans deposit buildup using the same type of detergents and dispersants as those used in high-quality engine oils." Use it "immediately before changing the engine oil and filter." Recommends that on engines with excessive deposits, such as high mileage or lengthy oil change intervals, the user should remove and clean the oil pan and oil screen before replacing oil and filter. Treats up to 6 quarts. ⚪
Pan and screen cleaning advised
Castrol Engine Flush Petrol and Diesel, Australian page: "Recommended for use in automotive petrol engines as part of routine oil changes." Directions: "run at idle for ten minutes and then change the engine oil as usual." Claims a formulation that "will not attack engine seals and other parts." The diesel version is "Specially formulated for Diesel Particulate Filter (DPF) compatibility." ⚪
10 minutes idle
Champion Lubes Engine Flush, article on its US site, 23 December 2021: "Four years or every 60,000 km as a guide," one bottle per 3 to 6 litres of oil, run for 15 minutes. Warns: "a lot of recent vehicles have no requirement for Engine Flush. Always consult your service manager before applying this to recently manufactured cars." ⚪
15 minutes, then drain
Comma Engine Flush, maker page (its country menu lists European sites): "Fast idle the engine for at least 10 minutes before draining the used engine oil." Also: "Engine Flush may also be added up to one week prior to servicing and it will work while you drive." Claims it "Helps free sticking valves and piston rings." ⚪
10 minutes or a week before
Liqui Moly Engine Flush, GB page, and Pro-Line Engine Flush product sheet PI 72/11/13/2023: "300 ml sufficient for up to 6 l of oil." Idle "approx. 10 minutes" (Pro-Line: "10 – 15 minutes depending on the degree of contamination"), then change oil and filter. Claims "does not attack common sealing materials" and "tested for turbocharger." Hazard line: "H304 May be fatal if swallowed and enters airways." ⚪
10 to 15 minutes
Lucas Complete Engine Treatment, maker page (an oil and fuel additive, not a flush): "Add 1 ounce only per quart of engine oil." "May be added with oil change or between oil changes." Claims it "Improves engine cleanliness reduces gum and varnish, especially in oil burners." ⚪
Stays in the oil
Motor Medic Motor Flush, maker page: "5 minutes is all you need." "DO NOT rev the engine or drive the vehicle." Calls it "Recommended before each oil change." Warns "longer application times (exceeding 5 minutes) could lead to engine damage" and "Extra care may be needed for high mileage engines with excessive sludge and contaminants." ⚪
5 minutes, never drive
Sea Foam Motor Treatment, maker page: one ounce per quart, added about "100-300 miles before your next oil change," "do not exceed one treatment per oil change interval", and "safe to leave in the oil for the entire interval." Says it "won't repair worn piston rings, valve seals, or other mechanical problems." ⚪
Added 100-300 miles early
Valvoline Engine Flush, Australian product sheet: "Add 350ml to the crankcase and allow the engine to run at normal idle for five minutes, do not drive the vehicle while Engine Flush is working." Note on the sheet: "Heavily sludged engines may require the oil pick up strainer to be checked to ensure no blockages to oil pump." Claims a "Non-solvent formulation that is safe for seal and gasket material." ⚪
5 minutes, never drive

Three things stand out in the grid. First, several rows carry a caution from the maker itself: Berryman's pan-and-screen advice, Champion's remark about recent vehicles, Motor Medic's time limit and do-not-drive line, Valvoline's strainer note. Second, the products make the same kind of claim (cleaner engine, free-moving parts, no harm to seals) and none cites a test we could read; the testing claims we found are vague: Liqui Moly's GB page says "tested for turbocharger" and "tested for particulate filters and catalytic converters," and its Pro-Line sheet cites "extensive testing in the laboratory and in practical field trials," and none names a test, a lab or a date. Liqui Moly's own product sheet adds that its information "may be considered reliable, although not legally binding." ⚪ Third, the claims about seals are the point on which GM's bulletin says something different, without naming any product: GM says analysis of "some of the aftermarket materials" indicates "the potential for damage to some engine seals and bearings." Neither side shows its data on its page.

Directions that disagree: how long, whether to drive, how much

The labels contradict one another on the three things a person actually has to do, so a rule taken from one product does not carry over to another.

How long the engine runs with the flush in it. Motor Medic and Valvoline's Australian sheet say five minutes. Liqui Moly says about ten, and ten to fifteen depending on contamination on its Pro-Line sheet. Castrol's Australian page says ten, Comma says at least ten at fast idle, and Champion says fifteen. Berryman's blog article describes three ways a flush can be done: one with a test drive, one that idles the engine for 5 to 10 minutes without driving, and one in which the oil is drained first and flush-containing oil is added, after which the engine is driven or idled.

Whether you may drive. Motor Medic and Valvoline's sheet say not to drive. Berryman's blog describes one method in which the car is taken for a test drive so the chemical can work through, and then given an oil change. Comma says its product may be added up to a week before servicing and works while you drive, and Sea Foam says to add its treatment 100 to 300 miles before the change. These are different products with different formulas, and the page you hold is the only one that applies: a permission on one label is not a permission on another. Sea Foam's page says its treatment is safe to leave in the oil for the entire interval; no flush label we read says that.

How much goes in. The label sizes are tied to oil capacity where one is printed, and the capacities they print are not the same:

Liqui Moly Engine Flush (GB page): 300 ml "sufficient for up to 6 l of oil"
6 litres of oil
Liqui Moly Pro-Line sheet: 500 ml "is sufficient for up to 5 l of oil"
5 litres of oil
Champion Lubes article: one bottle per "3L – 6L of engine oil"
3 to 6 litres
Berryman and Motor Medic: "up to 6 quarts" (Berryman); "up to 6-7 quarts" (Motor Medic), a second bottle may be needed at 10 quarts or more
6 to 7 US quarts
Sea Foam and Lucas: one ounce per quart of oil in the crankcase
1 oz per quart
Valvoline (Australia) and Comma: 350 ml; "complete contents of this pack" (0.4 L); no oil capacity printed
No capacity given

Two practical consequences follow from the grid. An engine with a large sump needs a larger dose by the label, and Motor Medic says a second bottle may be needed for 10 quarts or more. And a product that prints no capacity limit leaves the reader to guess, which is a reason to ask the maker or the shop before you pour.

Turbo, diesel and particulate filters: claims against the manual

Product pages market their flushes for the engines where owners worry most. Liqui Moly's GB page says its flush is "tested for turbocharger" and "tested for particulate filters and catalytic converters." Castrol's Australian page says its diesel flush is "Specially formulated for Diesel Particulate Filter (DPF) compatibility." Motor Medic recommends its synthetic version for "all diesel and turbocharged engines." ⚪ Each is a claim from the seller of the product.

Against that stands what car makers print about those engines. Mazda's turbocharger instructions, in the 2021 CX-5 and 2025 CX-90 manuals, say to change the oil and filter on the schedule and then: "Use only recommended engine oil." and "Extra additives are NOT recommended." ⚪ GM's engine crankcase paragraph is limited to gasoline engines and says nothing about diesels; our searches found no diesel-engine statement from any car maker that approves a flush. For a car with a diesel particulate filter or a turbocharger, the question to ask is whether the car maker's own document says anything about additives at all. If it advises against additives, as Mazda, Mercedes-Benz and MINI do for the cars we read, a product page's compatibility claim does not override it.

Shortlist by situation: what each maker prints

For flushes the useful situations are about the engine's history and the maker's paper, and the first row is the one the car makers' documents point to. No row is a recommendation.

Your manual advises against additives: the documents above point to doing nothing extra and changing the oil and filter on the schedule in the manual. GM, Kia and American Honda say so in terms. ⚪ Nothing on this page is a reason to override a maker's paper.
No product
You still want a flush and the oil is being changed anyway (idle-and-drain products): Berryman Oil Change Flush, Castrol Engine Flush (Australia), Champion Lubes Engine Flush, Comma Engine Flush, Liqui Moly Engine Flush and Pro-Line, Motor Medic Motor Flush, Valvoline Engine Flush (Australia). Directions run from 5 to 15 minutes; whether to drive differs; read the label. ⚪
Alphabetical, no ranking
You want a treatment left in the oil instead of a flush: Lucas Complete Engine Treatment (one ounce per quart), Sea Foam Motor Treatment (one ounce per quart, one treatment per oil change interval). These are additives, and the car makers' additive statements apply to them. ⚪
Alphabetical, no ranking
Diesel, turbo or particulate filter (the makers' own claims): Castrol Diesel flush (Australian page, DPF compatibility), Liqui Moly (GB page says tested for turbocharger and particulate filters), Motor Medic synthetic flush (recommended for diesel and turbo). Check your maker's manual first; Mazda says extra additives are not recommended in turbocharger engines. ⚪
Manual first
Used car, history unknown, sludge suspected: product pages here describe sludge removal. Berryman says to clean the oil pan and screen on engines with excessive deposits, Valvoline's sheet says the oil pick-up strainer may need checking, and Motor Medic says extra care may be needed. ⚪ Opening the pan is a job for a technician, which is our reading of those notes.
Inspect first

The shortlist leaves out products we could not read: AMSOIL's Engine and Transmission Flush page refused our request, and we did not find readable product pages for Mobil, Pennzoil or Rislone. That is a limit of this page, not a view of those products.

What a flush is said to risk, and what the labels themselves warn about

The risks that appear in the documents come from two directions, and neither comes with data on its page.

From the car makers: GM says analysis of some aftermarket crankcase-flushing materials indicates incompatibility with its engine components and "the potential for damage to some engine seals and bearings," and that returned parts exposed to flushes "show indications of potential damage and shortened durability." ⚪ Kia says flushes and additives "May cause and/or contribute to component failures." ⚪ Nissan and Infiniti say the chemicals or solvents in many aftermarket flushing systems have not been validated by them, Subaru says the chemicals in non-approved systems have not been tested or approved by it, and all three say they strongly advise against performing these services. ⚪ Mazda says extra additives are not recommended in its turbocharged engines, and MINI says "Oil additives can damage the engine." ⚪ None of these papers describes a single case, a test method or a failure rate.

From the product makers' own pages: Motor Medic warns that leaving its flush in longer than five minutes "could lead to engine damage." Berryman, whose flush is described as gentle, still advises cleaning the oil pan and screen on high-deposit engines. Valvoline's Australian sheet says a heavily sludged engine may need its oil pick-up strainer checked for blockages. Champion Lubes says a lot of recent vehicles have no requirement for a flush. ⚪ These are caution lines a maker thought worth printing; none says how often something went wrong.

One more line of risk is about what the product itself is. Liqui Moly's GB product page carries the signal word "Danger" and the hazard statements "H304 May be fatal if swallowed and enters airways," "H317 May cause an allergic skin reaction" and "H319 Causes serious eye irritation." ⚪ These are labelling statements for the product, and they are a reason to read the bottle and keep it off skin and out of reach.

Independent evidence: what we could and could not find

We found no laboratory test of engine flushes and no consumer-organisation test on a page we could read, so there is nothing independent to put beside the makers' claims. What exists is opinion from journalists and one instructor, and it is only useful as a sign of how the question is discussed.

The Globe and Mail, a Canadian newspaper, ran a reader question on 12 March 2013. It reports the view of Dennis Mott, an automotive professor at Centennial College in Toronto: "If you do your oil changes regularly you shouldn't have a need for an engine flush," and "Ninety-nine per cent of cars on the road will never ever need one." Mott adds that a flush "might not be a bad idea if you're buying a used car with 100,000 km or more on it and don't know if the oil was changed regularly." That article is a newspaper's Q and A, not a study; the figure is a professor's estimate. Mott also says "No manufacturer in the world is going to recommend one," which is a sweeping statement we could not verify across all makers; we can say only that none of the thirteen brands we read recommends one.

SlashGear published an article on 4 July 2024 by its writer Alvin Reyes, who relates a personal case on a used car: "The flushing worked like a charm, but the engine began having oil leaks a week or two after flushing." A single anecdote proves neither safety nor harm.

We looked for statements by standards bodies and found none that address flush products. The American Petroleum Institute page we read describes how engine oils are licensed and says nothing about aftermarket flushes. That is not evidence either way; it is a gap.

If you are worried about sludge or an unknown oil history, what the documents point to

The documents lead to a short list. We label each step with whose words it is.

Follow the oil-change schedule in your manual. American Honda's statement says oil changes should be done "in accordance with maintenance minder and the Acura owner's manual." Kia's bulletin says its manual identifies Normal and Severe schedules, and Honda's statement says only a small percentage of Acura owners drive in severe conditions that might call for more frequent changes. ⚪ The steps for doing the change are in our how to change oil guide, and the price side is in our oil change cost guide.

Use the oil the manual names. Which viscosity and specification to buy is in our what oil does my car take guide, and whether to move between synthetic and conventional is in our synthetic versus conventional oil guide. Valvoline's shop blog says the most effective way to deal with sludge is to switch to a high-detergent oil, and that signs of sludge include oil that looks like "chocolate pudding on the dipstick" and low oil pressure warnings on the dash. ⚪ That is Valvoline's view of its own category, and we did not test the claim; in our view, confirming sludge is a technician's job.

Have a technician look. Berryman's pan-and-screen advice and Valvoline's strainer note both lead to a person who can open the engine, and Motor Medic says extra care may be needed. Valvoline's blog says that if a noise is caused by wear damage that has already occurred, cleaning "will help prevent further damage but won't reverse it." ⚪ We say it plainly as our advice: a flush bottle is not a repair for a noise, a warning light or oil consumption.

Treat the oil pressure light as an emergency. If the oil pressure warning light comes on, stop the vehicle safely as soon as possible, switch the engine off and have the car towed; do not keep driving to see whether it goes out. Nissan's manual says "Stop the vehicle safely as soon as possible. Stop the engine immediately and call a NISSAN dealer" and adds that running the engine with the light on "could cause serious damage to the engine." Mazda's says "Do not run the engine if the oil pressure is low." ⚪ Our low oil pressure warning guide covers the light itself.

Safety, temperature and what to do with the old oil

Read the label for temperature, because the products differ: Liqui Moly says to add its flush "to the motor oil at operating temperature," Comma says "When the engine is warm," and Motor Medic says to add it "to your cold engine." ⚪ A warm engine is a hot engine to touch, and Mercedes-Benz's manual warns of "Risk of burns from hot component parts in the engine compartment" and says to allow the engine to cool down. ⚪ Our how to change oil guide lists the steps and the maker warnings for draining hot oil.

The mixture that comes out is used oil with a chemical in it. The US Environmental Protection Agency says used oil should be collected in a leak-proof container and taken to a recycling facility, with the drained filter, and notes that used oil from one oil change can contaminate one million gallons of fresh water. 🟢 The EPA page does not mention flush products; whether a collection point accepts oil mixed with one is a question for that point.

Prices: what any page printed

No flush maker's or shop's page we read printed a price for any flush or for the service. Jiffy Lube Ontario lists the service without one, the product makers' pages carry none, and we do not quote retail listings or comparison sites, because their prices change by the day. The question of what a shop charges for oil work in general is in our oil change cost guide, which also covers the upsell menu where flushes tend to appear.

Best engine flush brands: why this page ranks none

Which engine flush brand is the best, and does PulsCar recommend one? PulsCar does not recommend a brand, because it sells no engine flush or oil additive, tested none, and takes no payment from any oil or additive company. No readable independent page compares flushes against each other, so a ranking would be an opinion without a named test behind it. The documents give a more useful order of questions: what your car maker's paper says about additives and flushing; whether your product's own label gives a time, a dose and a driving rule that fit your engine; and whether you have a symptom, because a symptom needs a technician and a warning light needs a stop, not a bottle. If a shop or a box offers you a product, ask which of those three it answers and what document says so.

The traps: three ways an engine flush purchase goes wrong

Trap one: reading "safe for seals" on the bottle as a car maker's approval. The situation: the box or the shop says the product is gentle, safe for seals and compatible with turbos and filters. What is real: those are the product maker's claims; GM says analysis of some aftermarket flush materials shows potential damage to seals and bearings, Subaru's warranties do not cover parts damaged by chemicals it did not approve, and no car maker's paper we read approves a flush. The price: a repair that nobody agrees to cover. The defense: ask which car maker's document approves the product for your engine, and treat a label as a sales claim until one does.

Trap two: using one product's directions on another's bottle. The situation: you remember five minutes or ten from an article or a friend. What is real: the labels disagree from five to fifteen minutes, from cold engine to operating temperature, and from never drive to drive. The price: Motor Medic says longer than five minutes could lead to engine damage and that you should never drive with its flush in the oil; another product has different rules. The defense: follow only the bottle in your hand, time it, and drain the mixture before you drive unless that label explicitly says otherwise.

Trap three: buying a flush to treat a symptom. The situation: a noise, an oil-pressure warning, smoke or oil consumption, and a quick-lube counter that offers a bottle. What is real: Sea Foam says its treatment "won't repair worn piston rings, valve seals, or other mechanical problems," Valvoline's blog says cleaning cannot reverse wear damage that has already occurred, and the oil pressure light calls for a stop, not a bottle. The price: a bill for an additive and a delay before the real cause is found, with an engine still running. The defense: if the light is on, follow the stop rule above; if the noise is new and the light is off, have a technician listen before anything goes in the oil.

Three typical situations

These are composite scenarios, not individual customers. They are built only from facts earlier on this page.

The owner who is offered a flush at the oil change counter. The service is listed as Engine flush – OSC on a Canadian page, with no price and the words "typically recommended when deposits begin to affect performance or as part of certain maintenance schedules." The useful questions are which maintenance schedule says so, and what the car's own manual says. If the car is a GM with a gasoline engine or a Kia, or the maker is American Honda (whose statement is for Acura), the maker's paper says it does not recommend a flush; for a Nissan, Infiniti or Subaru, the paper advises against aftermarket flushing systems; for a Toyota, we found no statement in the manual text we read, which means the shop has to point to something else.

The buyer of an older used car with no oil-change records, worried about sludge. The sources do not support a flush as the first step. Valvoline's blog points to oil, Berryman and Valvoline's sheet point to a look at the oil pan and strainer, and the newspaper expert quoted above says a flush "might not be a bad idea" in that case, which is an opinion. The useful order is to have a technician look first, fix any symptom the look finds, and then follow the maker's schedule.

The owner of a turbocharged diesel who reads that a flush is tested for turbochargers and suitable for particulate filters. Those words come from the product maker. Mazda's turbo instructions say extra additives are not recommended, and our searches found no diesel statement from any car maker that approves a flush. The decision is not whether the product page is truthful, but whether the car maker's document says anything about additives for that engine; if it says no, or says nothing, the next call is to the dealer or the maker's customer line.

Where a sound check fits, and where it does not

This is our side of the page, so check it against the homepage. PulsCar's homepage describes a free 30-second engine sound check, with no card, and a result on screen about a minute after upload; it also says the free check is a screening from sound, not a hands-on inspection.

Can a PulsCar sound check tell me whether my engine needs a flush? No. The check listens to a recording of the engine running; it cannot see sludge in the oil pan, judge the condition of the oil or read oil pressure, so it adds nothing to the decision this page is about, and PulsCar sells neither a flush nor an additive. Its narrow use is a new engine noise on a car that is otherwise behaving normally, and it is a screening, not an inspection. Brakes that feel wrong, steering or wheel noise, a flashing or red warning light: inspect first, do not record. If the oil pressure warning light comes on, stop the vehicle safely as soon as possible, switch the engine off and have the car towed; do not keep driving to see whether it goes out.

What this page cannot tell you

We tested no flush, so nothing here says that one product cleans better, harms less or costs less than another. We quote no flush price in dollars. We read owner's manuals and bulletins from thirteen car brands, in the model years named in the grid; a different year or engine may print something else, and Ford, Jeep, Chrysler, Dodge, Volkswagen, Volvo, BMW and Lexus are not in the grid because we did not read their manuals. We could not read AMSOIL, Mobil 1, Pep Boys or Ford's support pages, which refused our requests (the Pennzoil address we tried did not exist), so a view that exists on one of them is missing. Technical service bulletins are written for dealers, and the Kia one is dated November 2012; we did not find out whether a newer one has replaced it. American Honda's statement is for Acura vehicles and reaches us through a copy hosted by I-CAR, and the 2023 Civic text we read is a copy hosted on a forum.

Several pages here are not US pages (Castrol and Valvoline Australia, Liqui Moly's GB page and Pro-Line sheet, the Comma page and Jiffy Lube Ontario), and a product sold in one country may be labelled differently in another. The dose, time and driving rules in the grids are what those pages printed on 15 November 2026; labels change, and the bottle you hold is the document that applies. Last, the warranty statements describe what makers wrote, not how a claim would be decided, and nothing on this page is legal advice.

Your action plan: before you buy, at the shop, after

Before you buy. Open your owner's manual and look in the engine oil section and the maintenance notes for the words additive, flush and flushing; if it advises against additives, as Hyundai, Kia, Mercedes-Benz, MINI, GM, Nissan and Infiniti do in the pages we read (and Mazda does for its turbo engines), that is the end of the shopping. If your maker is GM (gasoline engines), Kia or American Honda (its Acura statement), its own paper says it does not recommend an engine flush. If the manual is silent, as Toyota's was in the text we searched, ask the maker's customer line or a dealer in writing whether it approves any product, and keep the answer. If you have a noise, a warning light or oil consumption, see a technician first. If the oil pressure warning light is on, do not shop first. If the oil pressure warning light comes on, stop the vehicle safely as soon as possible, switch the engine off and have the car towed; do not keep driving to see whether it goes out.

At the shop. You can decline a flush at the counter; the oil change does not depend on it (our advice). Ask which problem the flush addresses on your car and what document says so. Ask for the product's name, the amount used and the price as its own line. Ask how long the engine will idle with the product in it, whether the car will be driven, and whether the oil and filter will be replaced straight after; the labels we read put the idle time between five and fifteen minutes, and some say never to drive. Ask what happens to the drained mixture. If the shop says your maker recommends a flush, ask to see the page. Our oil change cost guide has the wider upsell checklist.

After. Keep the work order with the product name and date. Watch the oil level and the oil pressure light over the next days. If the oil pressure warning light comes on, stop the vehicle safely as soon as possible, switch the engine off and have the car towed; do not keep driving to see whether it goes out. Return to the schedule in your manual for the next oil change; our how to change oil guide and what oil does my car take guide cover the change itself and the oil.

Sources and documents

Each page below was read on 15 November 2026 unless it says 11 or 12 November 2026. Marks: 🟢 government text; ⚪ a car, oil or product company's own statement. Trade and consumer articles are named by publisher and date.

  1. 🟢 US Environmental Protection Agency, Managing, Reusing, and Recycling Used Oil; 16 CFR 700.10, prohibited tying
  2. ⚪ GM service bulletins on NHTSA: 04-06-01-029K, October 2024; 04-06-01-029I, September 2017; 04-06-01-029H, February 2016; 12-06-01-008A (GM of Canada), October 2012
  3. ⚪ GM owner's manuals (read 12 November 2026): 2025 Chevrolet Silverado 1500; 2026 Chevrolet Equinox
  4. ⚪ Kia: technical service bulletin 058, November 2012; 2024 SK3 web manual, normal maintenance schedule (read 11 November 2026)
  5. ⚪ American Honda, position statement on additives, fluids and flushes for Acura vehicles (copy hosted by I-CAR); Honda Canada 2012 owner's manual (read 11 November 2026); a forum-hosted copy of the 2023 Civic maintenance section (read 11 November 2026, not linked)
  6. ⚪ Hyundai web manuals: 2024 CN7, 2026 LX3 (both read 11 November 2026), 2025 NX4 (read 15 November 2026); PDFs: 2023 Hyundai Elantra, 2023 Genesis GV70 (both read 12 November 2026)
  7. ⚪ Nissan and Infiniti manuals (read 12 November 2026): 2026 Rogue; 2023 Frontier; 2025 Infiniti QX60
  8. ⚪ Subaru owner's manuals (read 11 November 2026): MSA5M2208A; MSA5M2403A
  9. ⚪ Mazda owner's manuals: 2021 CX-5 (read 12 November 2026); 2025 CX-90 (read 11 November 2026)
  10. ⚪ Mercedes-Benz 2022 C-Class and 2022 GLE manuals; MINI 2025 Countryman manual (all read 12 November 2026)
  11. ⚪ Toyota owner's manuals (read 12 November 2026): 2021 RAV4 Hybrid; 2015 4Runner; Ram 2022 2500/3500 owner's manual pages on special additives and engine oil selection (the Ram pages read 15 November 2026)
  12. ⚪ Valvoline: global Engine Flush page; shop blog How to Remove Engine Sludge and Deposits, 11 August 2026; Engine Flush product sheet (Australia). Castrol: What is motor oil? (US, read 11 November 2026); Engine flush and fuel treatment products (Australia)
  13. ⚪ Product makers: Berryman, The Best Way To Flush Engine Oil; Champion Lubes, Engine flush: what it is and how it is used, 23 December 2021; Comma Engine Flush; Liqui Moly, Engine Flush (GB) and Pro-Line Engine Flush product information; Lucas Complete Engine Treatment; Motor Medic Motor Flush; Sea Foam, how to add Motor Treatment to crankcase oil; Jiffy Lube Ontario engine services
  14. The Globe and Mail, Does my car really need a complete engine flush?, 12 March 2013; SlashGear, Are Engine Flushes Safe And Do They Actually Work?, 4 July 2024
  15. American Petroleum Institute, engine oil page (read 11 November 2026)
  16. PulsCar homepage (sound check terms)
  17. What we could not read, and so did not quote: AMSOIL (product and blog pages), Mobil 1, Pennzoil, Rislone, Pep Boys, Ford's support pages, Rick's Free Auto Repair Advice, FCP Euro, Brake and Front End and a Bumper article (refused access, or did not exist at the address we tried)

Prices verified: no engine flush prices are printed on this page; none were printed on the maker and shop pages read, 15 November 2026 · Technical documents verified: 15 November 2026 · Reviewed quarterly

Saw a product label, a maker statement or a figure that differs from this page? Email [email protected] with the product, the vehicle and the source.