💡 The answer in 60 seconds

Only a check engine light? Any tool that reads the standard OBD-II layer reaches it; Honda's manuals describe the lamp as an emissions-system indicator and the readiness status as something the lamp itself shows at key-on.
Honda ABS, airbag or TPMS codes? Pick a maker that lists Honda for those systems and check your model year in its list. OBDLink prints years (Civic 2006-2019, Accord 2008-2019, CR-V 2007-2019), Innova prints four Honda tables, Autel lists Honda by make only.
Oil-life or tire-pressure reset? Honda's manuals show you do both on the car (where they print the tire procedure), so in our reading a scanner's reset menu is a convenience.
Honda's own tool? It is i-HDS with a J2534 interface, and in a collision-repair statement Honda says it does not test other scan tools.
A 2021 or newer Honda? No Honda model list read goes past 2020; Innova's coverage page says 1996 to 2022 in general.
Flashing light? Our advice, not Honda's: pull over safely, switch the engine off and have the car towed.

Which scanner to put in a Honda looks like one question and is four. A lit check engine light is a standard OBD-II question that almost any tool answers. A lit ABS, airbag or tire-pressure lamp is a Honda-specific question: the codes live in modules the standard does not reach, so the answer depends on what a maker built for your Honda's model year. An oil-life reminder or a tire-pressure calibration is a procedure Honda's manuals, where they print it, put in the owner's hands. And the work Honda's own i-HDS software does, such as reprogramming, is done in Honda's software with a J2534 interface, and no tool in the shortlist below lists Honda reprogramming. This page keeps the four apart and reads, for each, what Honda and the makers printed.

We make PulsCar, which sells a subscription app that works with the OBDLink MX+ and with other Bluetooth OBD-II scanners as the checkout page describes; this is a comparison by us, with sources and dates. PulsCar is on the shelf below in its alphabetical place and is held to the rules applied to the others. No scanner is included with a PulsCar membership, and no link on this page is an affiliate link. We rank nothing: the shortlist is alphabetical, and "best" in the title is the question asked, not our judgement.

For a shelf across all brands and cars, see our scanner shelf; for handheld readers against phone adapters, our code reader guide and the Bluetooth guide; for the MX+, our OBDLink MX+ review. For each Honda's known problems by mileage, see the Accord, Civic, CR-V, Pilot and Odyssey.

Which scanner for a Honda? The verdict by job

Which OBD2 scanner should a Honda owner buy, and where does PulsCar fit? It depends on the job. For a lit check engine light on one car, a standard OBD-II reader is enough, and OBDLink says its adapters support all OBD-II compliant vehicles. For Honda ABS, airbag or TPMS codes, choose a maker that lists Honda for those systems and check your model year in its list; OBDLink, Innova and Autel each print something, in different detail. Honda's manuals put the oil-life reset, and the tire-pressure calibration where printed, on the car. PulsCar is an app: its checkout page lists reading codes, live readings and clearing codes on any ELM327 adapter on Android and on an MX+ or a Bluetooth LE adapter on iPhone, and prints no Honda-specific functions. The table below sets each job against the sources, and the sections after it give the printed words.

A check engine light and nothing else, one Honda — any tool that reads the standard OBD-II layer; OBDLink says its adapters support all OBD-II compliant vehicles, Honda's manuals describe the lamp as an emissions-system indicator
Generic OBD-II
ABS, airbag (SRS), TPMS or VSA codes — a maker that lists Honda for those systems; OBDLink lists Honda modules and years, Innova prints four Honda tables, Autel lists Honda by make
Check the year list
Oil-life or Maintenance Minder reminder — Honda's manuals print the reset steps for the owner; several scanners also list an oil reset
Honda: on the car
TPMS light after a tire change — the Honda manuals that print it give a calibration from a menu or button plus about 30 minutes of driving
Honda: on the car
Steering-angle reset, electric parking brake, battery reset — Innova ticks the steering angle on all four Hondas and differs by year on the other two, Autel lists Honda by make
Varies by model year
Reprogramming — Honda's 2025 statement names the Denso DST-i as the only factory-approved interface for diagnostics and reprogramming, and says i-HDS needs a J2534 interface
Honda's own tool
Every drive recorded by a phone app — apps such as PulsCar; always-on features need the OBDLink MX+
Plan plus a scanner

What this page reads, and how

Every number below is printed on a page read on 17 November 2026, except our sums and labelled advice, and every quotation is verbatim from a saved copy of it. The Honda documents are six Honda Canada manuals (2013 Civic 4-door, 2013 Fit, 2014 CR-V, 2014 Pilot, 2016 Civic Sedan, 2016 CR-V), seven Honda UK manuals (named by their file names: a 2016 Civic, 2018 CR-V, 2018 HR-V, two Jazz manuals, the CR-V e:HEV and a Super-N), the Honda UK web manual for the Prelude, more than twenty short excerpts from Honda's US owner site (their model years come from their file names, not their text), two Honda Canada manual web pages whose model is not printed, and Honda's July 2025 position statement on scanning, read as hosted by I-CAR. Scanner makers' pages and manuals were read for Honda and Acura statements; where a page printed nothing about Honda, this page says so.

Honda's independent-repair site and online store answered HTTP 503, a maintenance page, on every address tried. Honda's tools page was read as an archived copy from 24 September 2022, which is the only way its subscription prices appear here, and BlueDriver's Honda announcement as an archived copy of a 2017 post. We tested no scanner and quote no review or rating; the only prices are ones a maker's own page printed.

What Honda's manuals say the check engine lamp means, side by side

Honda calls the check engine light the malfunction indicator lamp. Its manuals agree on the meaning and, where printed, on the blinking rule, and differ on small points. The wording below is Honda's, and the manual for your Honda decides.

Honda Canada manuals, 2013 Civic 4-door, 2013 Fit, 2014 CR-V, 2014 Pilot, 2016 Civic Sedan and 2016 CR-V — steady lamp: "Avoid high speeds and immediately get your vehicle inspected at a dealer." Blinking: wait at least ten (or 10) minutes with the engine stopped; if it blinks again on restart, 31 mph (50 km/h) or less to the nearest dealer
Canada, 2013-2016
Honda UK manuals, a 2016 Civic, 2016 Jazz, 2018 CR-V and 2018 HR-V, and the CR-V e:HEV and Jazz HEV (editions marked 26) — same steady wording and ten-minute wait; after a repeat blink 50 km/h (30 mph) or less (the Civic text says 50 km/h or less); the hybrids add "electric vehicle system" to what can light the lamp
UK, 2016-2018 and 26
Honda US owner-site excerpts — 2019 Odyssey, Pilot, Passport and Fit: "Stop in a safe place and wait for the engine to cool down." with no minute count; 2020 Odyssey, Insight and Accord Hybrid: "Stop the engine for 10 minutes or more, and wait for it to cool down."
US excerpts, 2019-2020

Every petrol or hybrid manual read ties the steady lamp to the engine emissions control system. The Honda Canada manuals for the 2013 Civic, 2013 Fit, 2014 CR-V and 2014 Pilot add the fuel cap: the lamp "Comes on when there is a problem with the engine emissions control system, or the fuel fill cap is missing, or loose." The 2016 CR-V manual lists the cap too, with "if" in place of "when". The 2016 Civic Sedan and the UK petrol manuals read do not mention the cap, and the UK hybrids add the electric vehicle system. Honda's manuals add a warning: "If you drive with the malfunction indicator lamp on, the emissions control system and the engine could be damaged." The 2013 Fit manual also describes a separate Check/Tighten Fuel Cap message, taken up in Scenario 1 below. A lamp that comes on is, in our reading, a reason for a code read, the first job for any scanner below, and Honda's wording for the lamp itself is to avoid high speeds and have the car inspected at a dealer immediately.

The blinking wording is the safety-critical part, and the page repeats Honda Canada's form. Honda's Canada manuals say, in the 2013 Civic wording: "Park the vehicle in a safe place with no flammable items and wait at least ten minutes or more with the engine stopped until it cools." and "If the malfunction indicator lamp blinks again when restarting the engine, drive to the nearest dealer at 31 mph (50 km/h) or less. Have your vehicle inspected." Our advice, not Honda's: if the check engine light is flashing, pull over safely, switch the engine off and have the car towed; the only exception, a flashing light alone on a car that starts and runs normally, is a shop within 2-3 miles, reached gently, at 31 mph (50 km/h) or less with light throttle. A scanner reads what the car stored after the event; it does not make a flashing lamp safe to drive on.

A lit ABS, airbag or brake lamp is a driving question before it is a shopping question. A Honda Canada manual page (model not printed) says of the anti-lock lamp: "Your vehicle still has normal braking ability, but no anti-lock function." It says of the airbag lamp: "There is a problem with one of the airbag systems or seat belt tensioners." And for the brake system lamp it says to check the pedal pressure, "If abnormal, take immediate action." and "Have your vehicle repaired immediately." Our advice, not Honda's: a scanner shows the stored code and can clear it, and clearing repairs nothing; a red brake lamp or a soft pedal means stop driving, pull over safely and have the car towed, and an airbag lamp needs a dealer check as soon as possible. Honda Canada's 2014 CR-V, 2016 Civic Sedan and 2016 CR-V manuals warn: "Ignoring the SRS indicator can result in serious injury or death if the airbag systems or tensioners do not work properly." Our pages on the ABS light, the airbag light and the brake light go through each.

Readiness codes: what Honda prints and what the federal test rule says

Readiness is the part of a Honda's self-diagnosis that matters most before an emissions inspection, and Honda shows it on the lamp itself. The Honda Canada manuals and the 2020 US Odyssey and Accord Hybrid excerpts describe the lamp coming on at key-on and going out, and say that "If “readiness codes” have not been set, it blinks five times before it goes off." The Honda Canada manuals explain how to check: "To check if they are set, turn the ignition switch to ON (w , without starting the engine. The malfunction indicator lamp will come on for several seconds. If it then goes off, the readiness codes are set. If it blinks five times, the readiness codes are not set." (the stray bracket is the PDF's key symbol). The manuals read from 2013 to 2016 add what erases them: "The readiness codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions."

One Honda Canada manual page, whose publication date in its address is 26 September 2018 and whose model is not printed, gives a preparation routine for a retest. It says to fill the tank to approximately 3/4 full, to leave the engine off for 6 hours or more at 40°F to 95°F (4°C to 35°C), to drive a highway at "a speed of 50 to 60 mph (80 to 97 km/h) for at least 20 minutes" without cruise control, then drive city or suburban traffic for at least 10 minutes and park with the engine off for 40 minutes. In the page's words, "If a testing facility determines that the readiness codes are not set, you may be requested to return at a later date to complete the test or see your dealer."

The federal inspection rule is the context for that routine. Under 40 CFR 85.2222, the inspector plugs the test system into the vehicle connector and reads the evaluation status; the rule says that "if the readiness evaluation indicates that any onboard tests are not complete, the customer shall be instructed to return after the vehicle has been run under conditions that allow completion of all applicable onboard tests." An exception allows vehicles that would otherwise pass to be issued a passing certificate when they are "MY 2001 and newer vehicles with no more than one unset readiness monitor" (two or fewer for MY 1996 to MY 2000), while a lit lamp with a stored code fails; and "If the MIL does not illuminate at all when the vehicle is in the key-on/engine-off condition, the vehicle shall fail the OBD inspection, even if no DTCs are present and the MIL has not been commanded on." States apply their own programs, and this page quotes no state rule. The connection to a scanner is plain: a tool that shows readiness status lets you see "not set" before a station does, and any step that erases codes or disconnects the battery can put the status back to "not set". Honda's manuals print the battery case, and two scan-tool makers print the clear-command case: Autel's MaxiCheck Pro manual says "the I/M Readiness Monitor Status for all vehicle monitors is reset to Not Ready or Not Complete status" when codes are erased, and adds "Do not erase the codes before the system has been checked completely by a technician.", and Thinkcar's ThinkScan Max page says its erase function "clears codes and resets monitors." No Honda page says what a scan tool's clear command does, so ask the tool's maker before clearing codes ahead of an inspection (our advice).

Innova's Honda tables tick I/M Monitor Status and Drive Cycles for all four Honda models, and PulsCar's checkout page lists readiness monitors among the things its Diagnose button reads.

What Honda prints about diagnostic tools: i-HDS, the interface and the 2025 position statement

Honda's words about other scan tools in the sources read come from one document, a position statement titled "Post-collision diagnostic scan and calibration requirements for Honda and Acura vehicles", issued July 2025 (version 6) and read as hosted by I-CAR. Its scope is collision repair, not owner scanning, and it should be read that way. Within that scope it is Honda's clearest statement about other tools: "American Honda's position is that the only way to accurately determine the post-collision status of all Honda and Acura vehicle electronic control systems is with the factory-authorized diagnostic software, i-HDS." It says of other tools: "American Honda does not test other scan tools or remote diagnostic services and cannot comment on their capabilities or accuracy."

Three more sentences from the same statement matter to a buyer who is not a collision shop. First, "Not all electronic control systems can be scanned using i-HDS." Second, "Dashboard indicators are intended for driver notification, not vehicle diagnostics." Third, "Many DTCs do not illuminate any dashboard indicators, so an electronic control system may operate improperly or be completely inoperative even in the absence of an illuminated indicator." The statement also says, of resets after parts replacement or a battery disconnect, that "Some reset procedures can be done without special tools. Others may require scan tool software." A quiet dashboard does not prove the modules are quiet, Honda says it does not test outside tools, and Honda says some resets may need scan tool software.

What the statement says about getting i-HDS: "i- HDS software, as well as other service information, is available to independent repair facilities and others for use on laptop or desktop computer hardware. These may be purchased in three time intervals: 1 day, 30 days, and 365 days." The software needs a Honda interface: it "requires the use of a Honda/Acura-specific, J2534-compliant vehicle communications interface (VCI) device" bought separately, and "The Denso DST-i is the only factory-approved VCI device for diagnostics and reprogramming." The Honda Tool and Equipment Program page (honda.snapon.com) prints a Honda interface, the Honda Antares Capsule, at "$896.00", calls it "the ideal upgrade or replacement for the DST-i", and says: "NOTE to non-dealer customers: The Honda Diagnostic System (i-HDS) Software Package is not included in the cost of the HAC." and "Requires an active i-HDS subscription for non-dealer customers."

Honda's current subscription prices could not be read: techinfo.honda.com and store.honda.com answered 503 throughout. An archived copy, saved on 24 September 2022, of Honda's page "Honda and Acura Vehicle Diagnostics" prints the subscription for the software it then called the Honda Diagnostic System (HDS), with the interface a separate item and no price for it, as "1 Day: $10.00 30 Day: $133.00 365 Day: $1547.00" and says the software is non-refundable, and lists what the software does: checks and clears diagnostic trouble codes, real-time data display, data capture, vehicle and system specific function tests, and control module reprogramming. Those prices are more than four years old and are not today's. On keys, that page says only: "To add, delete or replace keys, refer to Keys and Codes in ServiceExpress."

Our advice, labelled: an owner scanning their own Honda for codes, a reset or live data is not in the market for i-HDS, and Honda's collision statement is not a reason to avoid a consumer tool for that. It is a reason not to expect module programming from one, and not to treat a clean consumer scan as Honda's blessing.

Can any OBD2 scanner read a Honda? Standard versus Honda-specific

The standard layer and the Honda layer are different documents. OBDLink's support page puts it in one sentence: "United States legislation requires all cars and light trucks built in model year (MY) 1996 and newer to comply with the OBD-II standard, which is defined by the Society of Automotive Engineers (SAE)." It adds that the standard's parameters are "mostly related to vehicle emissions" and that "Any PID not on this list is considered a manufacturer-specific PID. For example, Transmission Temperature is not included in the OBD-II standard list." Anything beyond that, OBDLink says, needs "enhanced diagnostics to read additional manufacturer-specific DTCs and Parameter IDs (PIDs)", with "reading and clearing codes for ABS (anti-lock braking system), SRS (supplemental restraint system), and TPMS (tire pressure monitoring system)" as common examples.

For a Honda, OBDLink's coverage PDF draws the line precisely. Its section 1 table, headed "OEM-Specific Enhanced Diagnostics Support", has four columns (Generic DTCs, Generic Live Parameters, OEM DTCs, OEM Live Parameters), and the Honda row carries marks under the first three and none under OEM Live Parameters (the marks are graphics, read from the page image; Acura's row is the same). OBDLink's own worked example, for Chevrolet, which has the same pattern of marks, explains what it means: the app "can only request the OEM DTCs and clear them." For a Honda, then, OBDLink's page lists manufacturer trouble codes and does not list manufacturer live data.

A Honda-specific protocol also appears in tool specifications. Autel's MaxiCheck MX900 manual and the MaxiCheck MX808S manual list "Honda Diag-H Protocol" among supported protocols, as does iCarsoft's JP V4.0 page; none of the three says which Honda models or years use it. An app can take the other route: Car Scanner's maker prints that its software works with every car that follows the OBD-II standard, adds that "most cars support advanced diagnostics in “manufacturer” mode" and that "In most cases, ELM327 can’t be used to operate in “manufacturer” mode." Its profile changelog lists Honda entries, for example "Honda: Fit GK3" and "Honda/Acura Hybrids", without dates and without saying which readings each profile adds.

Which Honda model years does each maker list (Civic, Accord, CR-V)?

The makers disagree about how much to print, and for a Honda that is the first thing to check, because a model-year gap is one way a Honda owner can end up with a tool that does not cover their car. The list below keeps each statement with its date and its limits.

OBDLink coverage PDF, Revision D (October 21, 2021) — Honda Accord 2008-2019, Civic 2006-2019, CR-V 2007-2019, Pilot 2009-2019, Odyssey 2008-2019, FIT 2009-2019; the list ends at 2019
Lists years to 2019
OBDLink, same list — HR-V 2016-2019, Ridgeline 2006-2014 and 2016-2019, Passport 2019, Insight 2010-2014 and 2019, Clarity 2009-2019, Crosstour 2009-2015, CR-Z 2011-2017, S2000 2005-2009
Years by model
BlueDriver, archived copy of an announcement dated December 8, 2017 — Honda and Acura enhanced diagnostics "on model years 2003 and newer" (future tense in the post)
2003 and newer, as of 2017
Innova, blog posts of 13 February 2024 (Honda) and 22 March 2024 (Acura) — tables for a 2008 Accord, 2014 CR-V, 2019 Civic and 2020 Odyssey, and for four Acura models; coverage page says model years 1996 to 2022
Four Hondas tabled
Autel, MaxiCheck Pro manual — Honda in the oil reset, EPB, ABS/SRS and SAS lists by make; no Honda model years printed (the manual says only "OBD II Diagnostics: 1996 and newer vehicles" in general); the manual prints no edition date
Make only, no Honda years
Thinkcar, ThinkScan Max page — lists Honda and says diagnosis covers all models that support OBD protocol after 1996
Make only
iCarsoft, JP V4.0 page — Honda and Acura among sixteen Asian makes; "Features vary by vehicle — confirm your model before you buy."
Make only
FIXD, FAQ — Honda and Acura listed for standard codes and for ABS codes; no model years in the saved text
Make only
Launch (a connector label only), Foxwell, Topdon, Veepeak and Vgate pages read — no Honda statement printed; Carista and Torque Pro name Honda only as a make, and Carly's Honda page prints general feature headings and says features vary by car
Nothing printed

Two cautions follow from the table. The OBDLink list stops at 2019, and Innova's blog tables stop at 2020 for Honda, so for a 2021 or newer Honda no make-by-year list read here says yes or no by model; Innova's coverage page says model years 1996 to 2022 in general and BlueDriver's 2017 statement is open-ended (2003 and newer). That is a gap in the pages, not a finding about the tools; the lists are different kinds of document (OBDLink's by model and year, BlueDriver's one sentence from 2017, Innova's four sample cars, the rest a brand). BlueDriver's own newer blog post, dated September 08, 2026, says generally that "Coverage can vary by model year, model, engine, installed equipment, and the region where the vehicle was originally sold." and points to its compatibility checker. BlueDriver's page that would hold a Honda statement today (www.bluedriver.com/news/honda-enhanced-diagnostics) answered HTTP 403 so only the archived copy is quoted.

Which Honda systems each maker says it reads

OBDLink prints the most specific Honda list. Section 3 of its coverage PDF lists the Honda modules the app has access to: ABS, Airbag, SRS, SRS Airbag, TPMS, VSA (vehicle stability assist), Electric Parking Brake, Electric Power Steering, Engine Control Module, Transmission/Transaxle Control Module, Continuously Variable Trans (CVT), Immobilizer, Keyless Access, Push to Start, Body, CAN Gateway, All Wheel Drive System, Seat Weight System and others, 33 entries in all. OBDLink's support article warns: "Your vehicle will likely support a subset of the modules listed in this section." The way in is a menu path in the free OBDLink app: "Tap Settings > Get Enhanced OEM Add-Ons." then pick the make and the model year; the download "may take 1-2 minutes"; for Honda and Acura "You do not need to select a vehicle network". The app's App Store history for version 6.10.0, dated 05/08/2025, says "Fixed a bug that prevented reading enhanced DTCs with the Honda and Hyundai/Kia OBDLink MX+ add-ons".

Who gets the add-on is the sharper point. OBDLink's support pages (the first sentence is in all three articles, modified 14 October 2026, 13 November 2026 and 1 April 2025; the second reads "PIDs and DTCs" in the 13 November one) say: "Add-ons that are exclusive to OBDLink MX+ include: GM; Honda, Acura; and Hyundai, Kia." and "If you have another OBDLink adapter model, then you can purchase add-on diagnostics, but they are not guaranteed to access all OEM-specific PIDs/DTCs." The OBDLink FAQ says "All OBDLink app OEM add-ons are free to MX+ users." No OBDLink page read prints a price for a Honda add-on. OBDLink's app page lists enhanced diagnostics for Ford through Infiniti and does not name Honda; the support pages do. OBDLink prints the MX+ at "$139.95" with free US shipping, with "an unconditional 180-day money-back guarantee, and a 3 year warranty."

Innova prints Honda in two ways. Its 5610 page lists Honda, "Including Honda & Acura", among supported makes, and says the tool will "Read and clear engine codes, OEM codes (e.g. ABS, Airbag, Transmission, etc.) and more." Its blog posts print the tables covered in the next section; its 5610 and 5510 product pages answered HTTP 429, so no Innova price is quoted.

Autel prints Honda by make. The MaxiCheck Pro user manual lists Acura and Honda for oil light and service reset, Honda for EPB service, Acura and Honda for ABS/SRS and for SAS and for DPF; the manual prints no Honda model years and no edition date. Autel's US store printed the MaxiCheck Pro at a "Limited Sale price $199.00" against a "Regular price $219.00" and also printed "Sold Out", with the note "The Autel Maxicheck Pro is not compatible with all vehicles, please contact us for a check before placing your order." Autel's other US site printed "This product has been discontinued." the same day. A 6 February 2026 article reprinted on autel.us describes a typical Honda and Acura workflow, "Enter VSA (Vehicle Stability Assist) module", then Special Functions and "Locate Steering Angle Sensor Neutral Position Memorization"; it does not say which tablets or Honda years.

FIXD's FAQ lists Honda and Acura among the makes for standard codes and for ABS codes, and its free-and-Premium comparison marks ABS reading with the qualifier "only available for select makes". It prints the sensor at "$59.99" and Premium at "$99.00 per year" and says live data depends on make and model. No FIXD page read names SRS, TPMS or any Honda reset. iCarsoft's JP V4.0 page lists Honda among sixteen Asian makes, says it covers more than the four standard systems (engine, ABS, airbags, transmission) and prints "PRICING ON REQUEST". Thinkcar's ThinkScan Max page lists Honda under "Cover 138 Brands" (it also prints other brand counts) and 28 maintenance services for most modern cars, with full functions after subscribing to its software (no price printed).

BlueDriver's Honda statement is the 2017 announcement quoted above: enhanced diagnostics on Honda and Acura reach modules such as "ABS, airbag, climate control", on model years 2003 and newer. OBD Fusion's page lists enhanced diagnostics for Ford through Alfa Romeo and does not name Honda or Acura. The Launch, Foxwell, Topdon, Veepeak and Vgate pages read printed no statement about Honda systems: Launch's manuals name Honda only as a label in a connector-location picture.

Innova's four Honda tables: what changes with the model year

Innova's Honda post of 13 February 2024 is the one place a maker prints the same tool's result for four Hondas side by side. The post says it uses the Innova 5610, says "not all features we offer may be accessible on your specific Honda vehicle", and says "The feature sets can vary based on the year, make, and model of each vehicle." Each table carries the note "image is for demonstration purposes only". The rows below are read from the saved text of the page.

Same on all four (2008 Accord, 2014 CR-V, 2019 Civic, 2020 Odyssey) — read and clear Engine, ABS & Brakes, SRS & Airbags; all-system scan; Oil Maintenance Reset; Steering Angle Reset; live data for Engine, ABS, SRS, Transmission and TPMS; pending codes, freeze frame, I/M monitor status, Mode 6
Ticked on all four
Battery Reset — ticked for the 2008 Accord and the 2019 Civic, crossed for the 2014 CR-V and the 2020 Odyssey
Differs by year
Electric Parking Brake (EPB) — ticked for the 2019 Civic and the 2020 Odyssey, crossed for the 2008 Accord and the 2014 CR-V
Differs by year
Permanent Codes — crossed for the 2008 Accord, ticked for the other three; O2S Results ticked only for the 2008 Accord
Differs by year
ABS Bleeding, DPF Reset, Brake Pad Life, Hybrid Battery Voltage — crossed on all four
Crossed on all four
Active tests — each table prints "Available Active Tests (0)" and "Not supported for this vehicle."; each lists the same 20 dealership-level routines, including EVAP TEST, IDLE ADJUST, FUEL PUMP ON and RADIATOR FAN
No active tests

Innova's Acura post of 22 March 2024 repeats the pattern for four Acura models; Oil Maintenance Reset is crossed for the 2013 Acura RL and ticked for the other three; the post's intro list and table headings disagree about the fourth car (NSX V6 against RDX). Innova says of the Honda results "We present this information to the best of our knowledge, but it is not guaranteed."

What the tables tell a buyer: read and clear for engine, ABS and SRS is ticked on all four cars from 2008 to 2020, a battery reset and an electric parking brake service follow the car, and no table says anything about a 2021 or newer Honda.

Honda oil and TPMS resets: what Honda lets you do on the car, and what scanners list

Honda's manuals put the two most common resets, the oil-life reminder and the tire-pressure calibration, in the owner's hands. The oil-life steps in the Honda Canada manuals for the 2013 Fit, 2013 Civic, 2014 Pilot, 2014 CR-V and 2016 CR-V are the same in outline (the Pilot's asks for a second hold of five seconds): "Reset the engine oil life display if you have performed the maintenance service." then turn the ignition on, display the engine oil life with the select/reset knob, press and hold the knob for ten seconds or more, then press the knob for five seconds or more, after which the engine oil life display returns to 100%. Honda's US owner pages for the Accord 2018, Pilot 2022, HR-V 2022, Ridgeline 2023 and CR-V Hybrid 2023 print the matching steps for their menus. Honda says who does it: "The dealer will reset the engine oil life display after completing the required maintenance service. If someone other than a dealer performs maintenance service, reset the engine oil life display yourself." and, in the 2018 Accord excerpt, "If you change or replace the vehicle’s engine oil yourself, you must reset the engine oil life."

Tire pressure follows the same pattern, with one difference between model years. Where Honda prints the rule in this form (the 2014 CR-V, 2016 Civic Sedan and 2016 CR-V manuals, and the US 2022 CR-V, 2020 Clarity Plug-In Hybrid and 2023 Accord Hybrid excerpts), it is the same: "You must start TPMS calibration every time you: • Adjust the pressure in one or more tires. • Rotate the tires. • Replace one or more tires." The calibration drive is "approximately 30 minutes of cumulative driving at speeds between 30-60 mph (48-97 km/h)" in the 2014 and 2016 CR-V manuals (30-65 mph for the 2016 Civic, 31-62 mph for the 2023 CR-V Hybrid), and the 2022 CR-V excerpt adds "TPMS cannot be calibrated if a compact spare tire is installed." The menu path in Display Audio cars is "From the HoMe screen, select Settings. 2. Select vehicle. 3. Select TPMS Calibration. 4. Select Calibrate." (the 2016 Civic Coupe excerpt, with its own capital letters). The 2013 Civic, 2013 Fit and 2014 Pilot Canada manuals print no tire-pressure calibration. Honda's archived tools page, which also lists a TPMS sensor reader, notes in that entry that "Non-location TPMS is used on all Hondas and Acuras, except 2013 Accord and 2013 ILX."

Honda prints a third reset in the Honda Canada manual for the 2016 Civic Sedan, for the case where the EPS, VSA, VSA OFF, CMBS and low tire pressure/TPMS indicators come on together: "you need to calibrate the VSA and EPS systems." followed by "Drive straight at speed more than 12 mph (20 km/h) for less than 10 seconds to calibrate the VSA and EPS systems." If the indicators still stay on, the manual says to "immediately have your vehicle inspected by a dealer." The same manual says that after a battery is reconnected the VSA and CMBS indicators may come on, and to "Drive a short distance at 12 mph (20 km/h). Each indicator should go off. If either or both do not, have your vehicle checked by a dealer."

Scanners list these jobs too, and the lists differ. Innova ticks Oil Maintenance Reset and Steering Angle Reset for all four Honda tables. Autel's manual lists Honda for oil light reset, EPB and SAS by make. Thinkcar's ThinkScan Max page lists 28 maintenance services "for most modern cars", with no Honda breakdown. Our advice, labelled: for the oil reminder and the tire calibration, use the procedure in your Honda's manual first, because it is free and Honda prints it; a scanner's reset menu earns its place for the jobs the manual does not put on the dash, and Honda's collision statement says that for some resets after parts replacement or a battery disconnect "Others may require scan tool software." Before you pay for a reset function, find your model year on the maker's list and ask what it does on your car, since Innova's tables show the same tool ticking a reset for one Honda and crossing it for another.

The shortlist by situation, in alphabetical order

This is not a ranking. It lists, alphabetically, the tools whose makers printed a Honda statement, plus PulsCar and the adapters that go with an app, each with the situation the printed words fit and the limit. The details are in the sections above; makers that printed Honda only as a name or a label are named in the last paragraph of this section.

Autel MaxiCheck Pro: a corded handheld for resets and ABS or SRS codes. The manual lists Honda by make for oil reset, EPB, ABS/SRS and SAS, with no Honda model years and no edition date. Autel's store printed "Limited Sale price $199.00" and "Sold Out", while autel.us said the product has been discontinued. Limit: no Honda model-year list on any Autel page read.

BlueDriver: a phone adapter with a 2017 statement that Honda and Acura enhanced diagnostics would be available on model years 2003 and newer. The Honda page is available only as an archived copy; the home page printed "$99.95". Limit: no Honda page readable today and no list of Honda modules beyond "ABS, airbag, climate control".

Car Scanner ELM OBD2 with a Veepeak or Vgate adapter: an app and a low-priced Bluetooth adapter. Veepeak printed the OBDCheck BLE at "$31.99" and recommends Car Scanner for most vehicles; Vgate printed the iCar Pro BLE4.0 at $33.99 and $38.99. Car Scanner's changelog lists Honda profiles. Limit: neither adapter maker prints anything about Honda.

FIXD: a plain-language code reader with a subscription tier. FIXD lists Honda and Acura for standard codes and for ABS codes, and prints the sensor at $59.99 and Premium at $99.00 per year. Limit: no SRS, TPMS or reset statement for Honda.

iCarsoft JP V4.0: a tablet-style tool for Asian makes. The page lists Honda and Acura, four standard systems plus more, and "PRICING ON REQUEST". Limit: no Honda function list, no model years, no price.

Innova 5610 family: a handheld with printed Honda tables. Four Honda cars and four Acura cars are tabled, and the 5610 page says "free updates for new models year vehicles." Limit: no readable price, and Innova says the information is not guaranteed.

OBDLink MX+ with the OBDLink app: Honda manufacturer trouble codes from a phone. OBDLink prints the Honda year list (to 2019), the module list and that the Honda and Acura add-on is exclusive to the MX+ and free with it, and prints the MX+ at "$139.95". Limit: Revision D of October 2021, no manufacturer live parameters for Honda, nothing after 2019.

PulsCar: a phone app that reads codes and live OBD-II readings and explains them in plain English, with always-on features on the MX+. The next section gives the printed facts. Limit: no Honda-specific function printed, and no Honda ABS, airbag or TPMS module reading on the page.

Thinkcar ThinkScan Max: a tablet with many reset functions. Honda is under "Cover 138 Brands" with 28 maintenance services for most modern cars, at $314.95 against $459.95, full functions after a software subscription with no price printed, with optional coding at "$49.95/ Year for one car make". Limit: no Honda model years.

Pages that printed nothing about Honda systems or functions: Carista (a brand list) and Carly (a Honda page with general headings only), Drew Technologies (a J2534 maker whose page names Honda HDS), Foxwell, Launch (a connector label only), OBD Fusion (Honda is not in its enhanced list), Topdon, Torque Pro (a make name in its store listing), Veepeak and Vgate. For those makers in full, see our Autel review, Foxwell review and Launch review; for FIXD and BlueDriver, the three-way page.

Adapters and phones: Bluetooth type, iPhone and Android

For a phone-based tool, the adapter decides which phones work, and the Honda question sits on top of it. OBDLink prints the MX+ as "Class 2 Bluetooth v3.0" with "‘Connect’ button – requires physical access to enable Bluetooth pairing", for "iOS, Android, Windows", and labels its OBDLink LX "not iOS compatible". Veepeak's OBDCheck BLE is described as "Compatible with iOS & Android"; Vgate's page lists the iCar Pro in Bluetooth 3.0, BLE 4.0 and Wi-Fi versions. PulsCar's checkout page draws the same iPhone line in its own words: on iPhone, an OBDLink MX+ or a Bluetooth LE adapter works, and "A classic Bluetooth ELM327 can’t connect to an iPhone"; on Android, any ELM327 adapter works for its Diagnose button, live readings and clearing codes. Our Bluetooth guide and the pages for iPhone and Android go through the phone question.

For a Honda, two adapter facts matter. OBDLink's support pages call the Honda and Acura add-ons "exclusive to OBDLink MX+". And a low-priced ELM327 can read the standard layer; the adapter makers print nothing on whether an app can reach Honda's ABS or SRS module through it. Our advice: if the reason you are buying is Honda ABS or airbag codes, buy the tool whose maker lists your model year, and keep the receipt until you have read an ABS code on your car.

What it costs, from printed prices

Every price here is one a maker's own page printed on 17 November 2026, except the archived Honda prices marked as such, and where a page printed none, the list says so.

OBDLink MX+, OBDLink's page, free US shipping; the Honda add-on is free with the MX+
$139.95
BlueDriver Pro OBD2 Scanner, BlueDriver's home page
$99.95
Autel MaxiCheck Pro, Autel's store (marked down from $219.00, shown Sold Out); autel.us says discontinued
$199.00
FIXD sensor and FIXD Premium, FIXD's FAQ; first year with Premium is $59.99 plus $99.00
$59.99 and $99.00 a year
Veepeak OBDCheck BLE and BLE+ Plus, Veepeak's home page
$31.99 and $41.99
Vgate iCar Pro BLE4.0, Vgate's store (two prices printed together)
$33.99 and $38.99
Thinkcar ThinkScan Max, Thinkcar's page (marked down from $459.95; software subscription price not printed)
$314.95
Thinkcar optional coding and actuation, per car make, per year
$49.95 a year
Honda Antares Capsule interface, Honda tool program; i-HDS subscription not included
$896.00
Innova 5610 and 5510 (pages not readable), iCarsoft JP V4.0 (on request)
No price read

Honda's own route, from the archived 2022 copy of its page, was "1 Day: $10.00 30 Day: $133.00 365 Day: $1547.00" for the HDS software subscription alone, with the interface a separate item and no price printed for it; today's prices could not be read. One arithmetic note: FIXD's first year with its Premium tier is $59.99 + $99.00 = $158.99, if you take both.

How much does it cost to read a Honda with PulsCar, and what does a scanner add to it? PulsCar's checkout page, read 17 November 2026, prints three plans: 1 Month at $19.99, 6 Months at $49.99 and 1 Year at $99.99, with 7 free days on the 1 Year plan only, and says no scanner is included. With an OBDLink MX+ at the $139.95 OBDLink prints, the 1 Year plan makes the first year $139.95 + $99.99 = $239.94. With a Vgate iCar Pro BLE at $33.99 (the lower of the two prices printed) it is $33.99 + $99.99 = $133.98, and with a Veepeak OBDCheck BLE+ Plus at $41.99 it is $41.99 + $99.99 = $141.98. PulsCar's page prints its own eBay prices (about $32, $53 and $140) for the Vgate, Veepeak and MX+, which are not the makers' prices used here; the $53 is for the Veepeak model the page names, OBDCheck BLE+.

Honda hybrids and plug-in hybrids: what Honda prints, what the makers list

A hybrid Honda changes the wording of two things on this page, and the scanner lists say little about it. Honda UK's CR-V e:HEV and Jazz HEV manuals (editions marked 26) add "electric vehicle system" to what can light the check engine lamp, and both add a hybrid case with no counterpart in the petrol cars: the lamp "Comes on when there is no petrol in the fuel tank, and goes off after vehicle is refueled, power mode is turned on, vehicle is driven, and the power system is turned off multiple times. If it does not go off, have your vehicle checked by a dealer." The Honda US excerpt for the 2019 Clarity Plug-In Hybrid prints no check-engine entry; it prints a Power System indicator: "Have your vehicle checked by an authorized Honda Clarity Plug-In Hybrid dealer immediately."

Honda UK's CR-V e:HEV manual also prints a warning: "Do not modify or attempt to repair your vehicle’s high-voltage hybrid power system or otherwise modify vehicle electrical systems. Disassembling or modifying electrical equipment can result in a crash or a fire." The CR-V e:HEV manual also says the High Voltage battery charge level may decrease when the 12-volt battery has been replaced or disconnected. For the scanner buyer the printed Honda hybrid coverage is thin: OBDLink's list includes Clarity 2009-2019, Insight 2010-2014 and 2019, and CR-Z 2011-2017 by name, and Car Scanner's changelog names a Honda/Acura Hybrids profile; OBDLink's module list names Drive Motor Control Module 1 and EDLC among Honda modules, and no maker page read lists hybrid battery readings for a Honda. If yours is a hybrid, ask the maker whether your exact model year's hybrid system is covered.

The diagnostic port, the 12-volt battery and leaving an adapter plugged in

Honda's newest manuals print a sentence about the port that the 2013 to 2016 manuals read do not. The Honda UK CR-V e:HEV, Jazz HEV and Super-N manuals and the Prelude web manual (its address says 2026) say: "The on-board diagnostic port (OBD-II/SAE J1962 connector) installed on this vehicle is intended to be used with automobile system diagnostic devices or with other devices that Honda has approved. Use of any other type of device may adversely affect the vehicle’s electronic systems or allow them to be compromised, possibly resulting in a system malfunction, drained battery, or other unexpected problems." This is Honda's text for UK-market cars, and its wording ends slightly differently in the Super-N manual ("a drained 12-volt battery") and the Prelude page (drainage of the 12-volt battery); the Honda Canada manuals of 2013 to 2016, the Honda UK petrol manuals of 2016 and 2018 and the US excerpts read print no such sentence, and we could not read a current US manual in full. No Honda manual read says where the port is.

The older manuals print a general rule, and the newest print it alongside: "Be sure electronic accessories do not overload electrical circuits or interfere with proper operation of your vehicle." and "Before installing any electronic accessory, have the installer contact a dealer for assistance. If possible, have a dealer inspect the final installation." In our reading, an adapter is an electronic accessory in that sense; Honda does not say so, and the sentence is Honda's, not ours. The adapter makers print their side: OBDLink lists "Automatic sleep & wake-up" and "BatterySaver™ Low Power Mode 2 mA" against an operating current of 62 mA; Veepeak says its adapter is "Safe to leave plugged in" and "runs quietly in the background without affecting vehicle warranty or battery life"; PulsCar's page says the MX+ sleeps ten minutes after the engine stops and draws about 2 mA.

Our advice, labelled: if your Honda's manual carries the port sentence above, read it as Honda's text on adapters and ask the dealer whether to leave one in; if it does not, unplug an adapter before a long storage or when the battery runs down. Honda's text on the battery is separate: a disconnected battery erases the readiness codes, and after reconnecting, the Canada 2016 Civic manual says the VSA and CMBS indicators may come on and to drive a short distance at 12 mph (20 km/h). OBDLink's own warning belongs in the plan: "You should only clear codes with the ignition ON and the engine OFF."

PulsCar and a Honda: what it does and what it is not

Does PulsCar read a Honda's ABS or airbag codes, and what does it need to run? PulsCar's checkout page, read on 17 November 2026, says its Diagnose my car button reads fault codes, the check-engine light, readiness monitors, battery voltage, coolant temperature, fuel trims, oxygen sensors and about 20 more readings, and that the app works with Bluetooth OBD-II scanners: on Android any ELM327 adapter, on iPhone an OBDLink MX+ or a Bluetooth LE adapter. It prints no Honda-specific function and no ABS, airbag or TPMS module reading; it lists six systems (engine, fuel, electrical, cooling, emissions and stored fault codes), and its compatibility note says some manufacturer-specific data is not available on every make. The page's footnotes say the Health Score is informational only and not a substitute for inspection by a qualified technician. Trips, scores and background watch need the OBDLink MX+.

The page prints these terms. The 1 Year plan ($99.99) has 7 free days, needs a card and then renews until you cancel; the 6 Months ($49.99) and 1 Month ($19.99) plans have no free trial; the page lists a 30-day money-back guarantee and says you can cancel in two clicks. Codes are explained in plain English from a lookup of 10,000+ codes and can be cleared from the result screen after a confirmation, not while the car is moving. Trip recording, the Health, Drive and Wear scores, the coach, background watch and wake-on-ignition "work only with the OBDLink MX+", in the page's words, not the MX, LX, EX or CX.

Here is what PulsCar is not, once and in one place. It is not a Honda-specific tool: the page prints no Honda ABS, SRS, TPMS or reset function, and a Honda owner who needs those should look at the makers in the shortlist that list Honda for them. It is not Honda's i-HDS, and in its collision-repair statement Honda says it does not test other scan tools. It does not include a scanner, so the first year costs the plan plus an adapter. It is a subscription that renews automatically until you cancel, where a one-time reader costs once. Where it fits, in our view: a Honda owner who wants standard-layer codes explained in plain English, live readings and, with an MX+, a record of every drive, and who does not need Honda's manufacturer modules. For the free OBDLink app on the same MX+, see our PulsCar versus OBDLink app page.

Three traps a careful Honda buyer still walks into

Trap one: reading "Honda" on a brand list as your model year and your systems. The situation: Autel's manual, FIXD's FAQ, iCarsoft's page and Thinkcar's page each list Honda as a make. What is real: none of those pages prints a Honda model year; OBDLink's list stops at 2019, and Innova's tables tick a battery reset for a 2019 Civic and cross it for a 2020 Odyssey. What to do (our advice): ask the maker, in writing, whether your exact model year and your exact system (ABS, SRS, TPMS, EPB) are covered, and keep the answer.

Trap two: clearing codes to make a lamp go out. The situation: a lamp comes on before an inspection and the tool offers a clear button. What is real: Honda's manuals say a disconnected battery erases the readiness codes, which set again only after several days of driving; Autel's manual and Thinkcar's page print that erasing codes resets the monitors, and Autel's manual adds not to erase codes before a technician has checked the system; and the federal inspection rule fails a vehicle whose onboard tests are still not complete after a return visit, with a narrow exception. What to do (our advice): read the code first, fix the cause, and expect to drive again before an inspection if you clear.

Trap three: treating a quiet scan as Honda's all-clear. The situation: the tool reads no codes and the car still behaves oddly. What is real: Honda's collision-repair statement says "Many DTCs do not illuminate any dashboard indicators" and that dashboard indicators are for driver notification, not diagnostics. What to do (our advice): describe the symptom to a shop that has Honda's own software and ask what it reads that a consumer tool cannot.

Three composite situations, decoded

These are composite scenarios, not individual customers. They are built only from facts already on this page and contain no invented names, amounts or dates.

Scenario 1: a message, then a lamp. Suppose a driver of a 2013 Fit sees the Check/Tighten Fuel Cap message. Honda's manual says to stop the engine, check the cap and drive for several days of normal driving, after which the message should go off; if the system keeps detecting a vapor leak, the lamp comes on, and for the lamp Honda says to avoid high speeds and have the car inspected at a dealer immediately. Lesson (ours): a lit lamp is the point for a code read, and the inspection comes first.

Scenario 2: ABS codes on a 2019 Civic. Suppose an owner has an ABS lamp on a 2019 Civic. OBDLink's coverage list shows Civic 2006-2019 and an ABS module, Innova's table for a 2019 Civic ticks reading and clearing ABS codes, and Honda says many DTCs light no lamp. Lesson (ours): this is the case where a Honda-listed tool earns its price, and the owner should confirm the model year and system in writing.

Scenario 3: an oil change at home. Suppose an owner changes the oil on a Honda and is offered a scanner for the reminder reset. Honda's manuals say that if someone other than a dealer performs the service, you reset the display yourself, and the 2018 Accord excerpt says you must. Lesson (ours): the reset is in the manual; a scanner's reset menu is a convenience.

What this page cannot tell you

  • Whether your exact Honda is covered. OBDLink's year list stops at 2019, Innova's Honda tables at 2020, and the Honda manuals read are for specific models.
  • What the tools do on a real car. We read pages, manuals and listings and tested no scanner.
  • Honda's current prices and statements. Honda's independent-repair site and online store answered HTTP 503, so the software prices are an archived 2022 copy (the $896.00 interface price was read live on the Honda tool program's page), and Honda's statements come from manuals and a 2025 position statement hosted by I-CAR.
  • What a scan tool's clear command does on a Honda. Autel's manual and Thinkcar's page print the general effect (monitors reset); no Honda page and no maker's Honda page prints it for a Honda.
  • Prices at other sellers. Innova's 5610 and 5510 pages answered HTTP 429, iCarsoft prices are on request, and no retailer price is quoted except the eBay prices PulsCar's page prints.

Your plan (our advice): before you order, on delivery day, in the first month

Before you order. Write down your Honda's model and year and the job: a lit check engine light, an ABS or SRS lamp, a reset, or every-drive reading. Find your year in the maker's list or ask the maker in writing which systems your year covers. Read your own manual's pages on the check engine lamp and the oil-life reset.

On delivery day. Plug the adapter in with the car stopped and the ignition on, read the stored codes, and write them down before you clear anything. Our advice: do not clear a code you have not understood, and do not clear codes before an emissions inspection, because Autel's manual and Thinkcar's page say erasing codes resets the monitors. OBDLink's own warning: "You should only clear codes with the ignition ON and the engine OFF." If you buy for ABS, SRS or TPMS, confirm on your car that the tool reads that module and shows the code behind your lamp, while the return window is open (OBDLink prints a 180-day money-back guarantee and PulsCar's page a 30-day one for its plan; Autel, FIXD and Carly print their own return terms, which this page does not compare).

In the first month. Do the oil-life reset from the dash after any non-dealer oil change, and the TPMS calibration after adjusting, rotating or replacing tires, as your manual prints them. Our advice, not Honda's: if the check engine light is flashing, pull over safely, switch the engine off and have the car towed; the only exception, a flashing light alone on a car that starts and runs normally, is a shop within 2-3 miles, reached gently, at 31 mph (50 km/h) or less with light throttle. Honda Canada's text for the blink is to wait at least ten minutes with the engine stopped and, if it blinks again on restart, drive to the nearest dealer at 31 mph (50 km/h) or less; Honda UK's manuals print 50 km/h (30 mph) or less.

Sources and documents

  1. Honda owner's manuals, Honda Canada (PDF, read 17 November 2026): 2013 Civic 4-door, 2013 Fit, 2014 Pilot, 2014 CR-V, 2016 Civic Sedan, 2016 CR-V; web pages Malfunction Indicators and Testing of Readiness Codes.
  2. Honda UK owner's manuals (PDF): see the Honda UK manuals page for the CR-V e:HEV, Jazz HEV, Civic, CR-V, HR-V, Jazz and Super-N files read, and the web manual pages for the Prelude indicators and Modifications and Accessories.
  3. Honda US owner site excerpts (owners.honda.com PDFs): 2022 Civic Hatchback instrument panel and the Dashboard Details, Maintenance Minder and Tire Pressure Monitoring System excerpts named in the text.
  4. American Honda, Post-collision diagnostic scan and calibration requirements for Honda and Acura vehicles, July 2025, version 6, as hosted by I-CAR. Honda's diagnostic tools page, archived copy, 24 September 2022 (unlinked, 429). The Honda tool program's Honda Antares Capsule page.
  5. OBDLink: Are enhanced diagnostics available for my vehicle?, Get Started with Diagnostics, OBD-II standard versus enhanced diagnostics, the OEM-Specific Enhanced Diagnostics Support Coverage PDF (Revision D, October 21, 2021), the OBDLink MX+ page and the FAQ.
  6. Innova: Honda post, Acura post, 5610 page and Coverage Checker. Autel: MaxiCheck Pro manual, MaxiCheck MX900 manual, MaxiCheck MX808S manual, MaxiCheck Pro page, Autel's store page for the MaxiCheck Pro (store.autel.com answered HTTP 429 when the links were checked, so it is not linked) and Stop Searching. Start Servicing.. BlueDriver: the Honda announcement of December 8, 2017 (archived copy of 7 March 2021; the archive answered HTTP 429 when the links were checked, so it is not linked), blog post of September 08, 2026 and home page.
  7. Other makers: FIXD FAQ, iCarsoft JP V4.0, Thinkcar ThinkScan Max, Car Scanner compatibility page, Car Scanner changelog, OBD Fusion, Veepeak, Vgate, Torque Pro on Google Play, Carly Honda page and Drew Technologies BodyShop page, and Launch's X-431 Turbo III and CRP 919 MAX manuals (Honda appears only as a connector label).
  8. 🟢 Government: 40 CFR 85.2222, Onboard diagnostic test procedures (eCFR, read 17 November 2026).
  9. PulsCar: get.pulscar.io, the checkout page read 17 November 2026 (plans, scanners, features).
  10. Not read, so not quoted: Honda's independent-repair site and online store (HTTP 503), Honda's current i-HDS prices, any current US owner's manual in full, BlueDriver's live Honda pages (HTTP 403, 404 and 429), Innova's 5610 and 5510 product pages (HTTP 429), the Thinkcar, Topdon and Veepeak product pages on their own shops (HTTP 429), Carly's support page on features and Carista's two help pages (HTTP 403), Launch's and Foxwell's Honda coverage (none printed), and any independent review.

Prices verified: 17 November 2026 in the maker pages they are quoted from, as printed to one connection · Technical documents verified: 17 November 2026 · Reviewed quarterly

Saw a price, a coverage line or a manual sentence that differs from this page? Email [email protected] with the model year, the source and the date.