💡 The answer in 60 seconds

10W-30 and 10W-40 share one cold grade and differ in the hot one, and your manual decides which of them, if either, your engine takes. The 10W is the same cold-start grade in both (a cold-cranking limit of 7,000 mPa·s at -25 °C in SAE J300); the number after the dash is the hot grade, set by viscosity at 100 °C: 30 means 9.3 to under 12.5 mm2/s and 40 means 12.5 to under 16.3, so a 10W-40 is thicker than a 10W-30 at 100 °C. What do makers allow? In the manuals we read, mostly neither. General Motors' 2014 Cruze, Silverado, Volt and Cadillac ATS manuals say not to use SAE 10W-30, 10W-40 or 20W-50. Ram's 2022 2500 and 3500 manual recommends 10W-30 for its 6.7L diesel above 0 °F. Toyota's 2015 Tacoma says that if 5W-30 is not available, 10W-30 may be used for its 5W-30 engine, and that it should be replaced at the next oil change. Can you switch? Our advice: only to a grade your own manual names, under the condition it prints. What to do (our advice): find the line for your engine, year and country in your manual and use that grade. If the red oil pressure light comes on while you drive, go straight to the section on the red oil pressure light.

PulsCar publishes this guide; it sells no oil, parts or servicing, and no link on this page is an affiliate link. Every maker statement below is a printed sentence or figure, or our labelled reading of a printed chart, for the model, engine and year named, read on 17 November 2026, and none of them is for your car unless it matches. This page answers one question: how 10W-30 and 10W-40 differ in the standard, what car makers print about either, and what they say about switching. The full grade tables and temperature charts are in the oil viscosity chart guide, which oil your car takes in what oil your car takes, synthetic against conventional in synthetic versus conventional oil, intervals in how often to change oil, the steps in how to change oil and brands in best synthetic oil. This page does not test or rank oils, so there is no best oil here.

What is the difference between 10W-30 and 10W-40, and can you switch? In short, by our reading of the tables (this PulsCar guide sells no oil): the two share the same cold grade, 10W, and differ in the hot grade, 30 against 40, so a 10W-40 is thicker at 100 °C, the hot-grade test temperature. In the manuals we read, mostly neither is named. General Motors' 2014 Cruze, Silverado, Volt and Cadillac ATS manuals say not to use either. Ram's 2022 diesel manual recommends 10W-30, Toyota's 2015 Tacoma and three Mazda manuals allow it as a stand-in or name it for some markets, and none of the manuals we read names 10W-40 as an allowed grade for a gasoline engine (a Kia diesel chart lists 10W-30/40; Ford's could not be read). Switching is a question for your manual: Hyundai, Genesis and Kia say other viscosities could result in engine damage, and Nissan and Infiniti serious engine damage.

When the manual decides: read this before anything else

The grade for your engine is printed in your owner's manual, and every other source on this page, the standard included, is secondary to it. SAE J300 defines grades; it does not say which grade suits which engine. Whitby, an author writing for the Society of Tribologists and Lubrication Engineers (STLE), puts it in one sentence: "Whether these oils are suitable for use in any specific engine depends on the characteristics and operation of that engine." The maker's engineers made that choice for your engine, and the manual is where they print it.

Castrol, an oil company, says the same on its viscosity page: "As far as the best oil to use, the best place to find that information out is in your vehicle owner’s manual." TotalEnergies, another oil company, advises: "If you have any doubt when choosing the viscosity grade of your motor oil, check your vehicle owner’s handbook, get the advice of a professional." Both sell oil in many grades, and on this point their pages send the reader to the manual.

So the rule of this page is short. The manual for your engine, model year and country decides the grade. This page shows what the numbers mean and what makers print; it does not say that 10W-30 or 10W-40 is right or wrong for your car. A statement below that is our own reading of a table or chart is labelled as ours, and advice that no source prints is labelled as our advice.

Three details of that rule matter here. The first is the country: Mazda's manuals print different oil text under headings such as Except U.S.A., Canada, and a US owner reading a Mexican-market sentence would be reading a rule that was not written for their car. The second is the engine: GM's 2014 Silverado prints 0W-20 for its 5.3L and 6.2L V8s and 5W-30 for its 4.3L V6 and 6.0L V8. The third is the year: GM's 2014 Cruze, Silverado, Volt and Cadillac ATS manuals carry a sentence about 10W-30 and 10W-40 that its 2025 and 2026 manuals no longer print.

What the two oils share: the 10W

The two oils have one thing in common in their names, and it is the part that is easiest to misread. The 10W in both is a winter grade. SAE J300 defines six winter grades, 0W, 5W, 10W, 15W, 20W and 25W, each with limits measured at a set cold temperature. Wikipedia's article on J300, which cites the April 2021 edition of the standard, prints the 10W row as a cold-cranking viscosity of at most 7,000 cP at -25 °C, a pumping viscosity of at most 60,000 cP at -30 °C, and a kinematic viscosity at 100 °C of at least 4.1. cP and mPa·s are the same unit, a measure of how thick (how slow to flow) the oil is; a higher number is thicker. The Olezol page, which reprints the January 2015 revision, gives the same figures for 10W. The J300 document itself is sold by SAE and was not read.

What those limits measure is how stiff the oil is when it is cold: the cranking test is about how hard the starter motor has to work against the oil in a cold engine, and the pumping test about whether the oil pump can move it. Holdmeyer, a retired Chevron Lubricants employee writing in STLE's magazine, notes that the pumping test temperatures are always 5 °C below the cranking ones.

Two sentences in the Wikipedia article explain how an oil ends up with a 10W label. "The grade of the oil is that associated with the coldest temperature at which the oil passes the test." And a multigrade oil must satisfy both parts at once; the article's example is the oil in this comparison: "A 10W-30 oil must pass the SAE J300 viscosity grade requirements for both 10W and 30", with "all limitations placed on the viscosity grades, such as the requirement that a 10W oil must fail the 5W requirements." So a 10W-30 and a 10W-40 are both oils that pass the 10W cold tests and fail the 5W cold tests. Our reading: as far as the standard is concerned, the cold behaviour of the two is classified identically.

That does not make the two oils identical in the cold. Whitby's article opens with the point that "Not all 0W-20 oils are exactly the same, nor are all 10W-40 oils, 20W-50 oils or other similar viscosity grades." The limit is a ceiling, and any oil under it carries the label; the same logic applies to two 10W oils, our reading. In a later paragraph he draws the comparison that matters here: "Hence, a 0W-20 oil will have similar low-temperature flow properties to a 0W-40 oil and a 5W-50 oil will have similar lubricating properties to a 20W-50 oil." Our reading: a 10W-30 and a 10W-40 are the same kind of pair: similar cold-start classification, different hot grade.

Where they differ: the hot grade, 30 against 40

The number after the dash is the hot grade, and this is the only part of the label on which 10W-30 and 10W-40 differ. SAE J300 has eight of these grades, 8, 12, 16, 20, 30, 40, 50 and 60. Each is defined by a viscosity range measured at 100 °C and a minimum measured at 150 °C under high shear, abbreviated HTHS.

For grade 30, Wikipedia's table prints a kinematic viscosity at 100 °C from 9.3 to under 12.5 mm2/s (the same as centistokes, cSt) and an HTHS minimum of 2.9. For grade 40 it prints 12.5 to under 16.3 mm2/s and an HTHS minimum of "3.5 or 3.7", without saying which oils the 3.5 and the 3.7 apply to. Olezol's January 2015 table splits grade 40 in two rows: an HTHS minimum of 2.9 for "0W-40, 5W-40 and 10W-40", and 3.7 for "15W-40, 20W-40, 25W-40 and 40". Whitby's remark fits that split: "There are slight differences in the limits for high shear rate viscosities for XW-40 oils, as readers will observe when studying the J300 specification."

The two tables disagree on the HTHS minimum for a 10W-40, 2.9 in Olezol's 2015 table and 3.5 or 3.7 in Wikipedia's 2021 table, so we do not pick a number: the standard is the place to check if the figure matters for your work. The 100 °C ranges are the same in both, and they are the part this page relies on. Our arithmetic from them: the grade 30 range is 3.2 mm2/s wide (12.5 minus 9.3) and the grade 40 range 3.8 wide (16.3 minus 12.5), and the two ranges meet at 12.5. By the tables, every oil that qualifies for the hot grade 40 is at least as thick at 100 °C as every oil that qualifies for 30, which is the 100 °C meaning of the statement that a 10W-40 is thicker than a 10W-30 once warm.

The two grades in one table

The rows below put the printed limits side by side, as Wikipedia prints them for the 2021 edition unless a row says Olezol. The right-hand column is a short label of each row's main limit. This is not a recommendation for either oil.

Cold grade, both oils: 10W. Cold-cranking viscosity at most 7,000 cP (mPa·s) at -25 °C; pumping viscosity at most 60,000 cP at -30 °C; viscosity at 100 °C at least 4.1 mm2/s. The 10W row is the same for both.
7,000 at -25 °C
Hot grade 30 (10W-30), both tables. Viscosity at 100 °C from 9.3 to under 12.5 mm2/s; HTHS viscosity at 150 °C at least 2.9.
9.3 to under 12.5
Hot grade 40 (10W-40), Wikipedia. Viscosity at 100 °C from 12.5 to under 16.3 mm2/s; HTHS at least 3.5 or 3.7, as the table prints it.
12.5 to under 16.3
Hot grade 40 (10W-40), Olezol, 2015 revision. Same 100 °C range; HTHS at least 2.9 for 0W-40, 5W-40 and 10W-40, and 3.7 for 15W-40, 20W-40, 25W-40 and 40.
HTHS 2.9 for 10W-40
Cold grade of the neighbour, 5W (5W-30). Cold-cranking at most 6,600 cP at -30 °C; pumping at most 60,000 cP at -35 °C; at 100 °C at least 3.8 mm2/s.
6,600 at -30 °C

Two things follow, both our reading of the table. The label 10W-30 is a promise about two sets of limits only, one cold and one hot, so it says nothing about the oil's actual numbers inside the ranges or its additives. And a switch between these two oils is a switch of the hot grade alone, as a switch from 10W-30 to 5W-30 is a switch of the cold grade alone. The full grade tables are in the oil viscosity chart guide.

What the makers print: thirteen makers in one table

We read the owner's manuals, or the online manual pages, of thirteen makers: Toyota, Honda, Hyundai, Genesis, Kia, Nissan, Infiniti, Mazda, General Motors (Chevrolet and Cadillac), Ram, Subaru, Mercedes-Benz and MINI. They are different models and years, so the table is a set of samples, not a verdict on a maker, and it says only what each printed about the two grades in this comparison.

General Motors, 2014 Chevrolet Cruze, Silverado, Volt and Cadillac ATS. Name SAE 10W-30, 10W-40 and 20W-50 and say not to use them.
Both named: do not use
Ram, 2022 2500 and 3500, 6.7L diesel. Recommends 10W-30 above 0 °F.
10W-30 recommended
Toyota, 2015 Tacoma, 4.0L V6. Allows 10W-30 if 5W-30 is not available; should be replaced at the next change.
10W-30 as a stand-in
Mazda, 2021 CX-5, 2023 MX-5, 2025 CX-50 (Mexico text under Except U.S.A., Canada headings). Name 10W-30 as the grade or as a stand-in.
10W-30 named
Genesis, 2019 G70 (US manual); Kia, DL3 2020 (online). Charts list 10W-30 among the grades.
10W-30 on the chart
Hyundai 2023 Santa Fe and Elantra; Genesis 2023 GV70. Print 0W-20 or 0W-30; other viscosities could result in engine damage.
Neither named
Nissan 2026 Rogue; Infiniti 2025 QX60. Print 0W-20; another viscosity could cause serious engine damage.
Neither named
Subaru, manual MSA5M2403A. 0W-20 synthetic is the required oil, 5W-30 conventional is allowed for adding oil; use only the recommended grade and viscosity.
Neither named
Mercedes-Benz, 2022 C-Class. Gasoline engines: only use SAE 0W-20.
Neither named
MINI, 2025 Countryman. Grade is on a sign in the engine compartment.
Neither named
Honda, 2026 HR-V and 2013 Civic (Canada). Chart shows 0W-20.
Neither named
Ram 2026 1500; GM 2014 Malibu, 2025 Silverado, 2026 Equinox and Express. Print 0W-20, 0W-40, 5W-20 or 5W-30 by engine.
Neither named

Our reading of the table: of the thirteen makers, six (GM, only to say not to use it; Ram, Toyota and Mazda in the text; Genesis and Kia in charts) name 10W-30 in one document or another, and GM's 2014 manuals are the only ones that name 10W-40 as a grade not to use. No manual we read names 10W-40 as a grade allowed for a gasoline engine; the one place we found it allowed is a Kia online chart for a 1.5 diesel, described below. That is a statement about the documents we could read: Ford's, Volkswagen's, Audi's, BMW's, Volvo's and Mitsubishi's could not be read, and an older or non-US manual from any maker might say something else.

General Motors, 2014: the manuals that name both grades and say do not use them

The clearest statement about this comparison we found is in General Motors' manuals from the 2014 model year, and it is a prohibition. The Chevrolet Cruze, Silverado and Volt manuals and the Cadillac ATS manual each have a Viscosity Grade paragraph in their engine oil section, and each ends with the same sentence.

The 2014 Chevrolet Cruze manual: "SAE 5W-30 is the best viscosity grade for the vehicle. Do not use other viscosity grade oils such as SAE 10W-30, 10W-40, or 20W-50." The 2014 Chevrolet Volt manual prints the same two sentences. The 2014 Chevrolet Silverado manual is split by engine: "SAE 0W-20 is the best viscosity grade for the 5.3L and 6.2L V8 engines. SAE 5W-30 is the best viscosity grade for the 4.3L V6, and 6.0L V8 engines. Do not use other viscosity grade oils such as SAE 10W-30, 10W-40, or 20W-50." The 2014 Cadillac ATS manual prints "SAE 5W-30 is the best viscosity grade for the 2.0L L4 engine and the 3.6L V6 engine. SAE 5W-20 is the best viscosity grade for the 2.5L L4 engine. SAE 0W-20 may be used as an alternative. Do not use other viscosity grade oils such as SAE 10W-30, 10W-40, or 20W-50."

Two details of GM's wording are worth keeping. The first is the verb: the sentence does not say that 10W-30 and 10W-40 are worse, it says do not use them, and it names 20W-50 in the same breath. The second is the alternative GM does allow: the ATS manual says SAE 0W-20 may be used as an alternative (the sentence follows the 2.5L engine's 5W-20 and names no engine), and all four manuals have a cold-weather paragraph, such as the Cruze manual's "In an area of extreme cold, where the temperature falls below −29°C (−20°F), an SAE 0W-20 oil may be used." The Silverado manual says an SAE 0W-30 oil may be used in the 4.3L or 6.0L engine in the same conditions. The cold alternative is a lower cold grade, not a higher one.

Not every 2014 GM manual we read has the list. The 2014 Chevrolet Malibu manual prints 5W-30 for its 2.0L and 2.4L engines and 5W-20 for its 2.5L, with SAE 0W-20 as an alternative, and does not name 10W-30 or 10W-40, so the sentence is not in every GM manual of that year.

It is also not in GM's newer ones. The 2025 Chevrolet Silverado 1500 manual prints "Use SAE 0W-20 viscosity grade engine oil for the 5.3L and 6.2L V8 engines." and "Use SAE 5W-30 viscosity grade engine oil for the 2.7L L4 engine." The 2026 Chevrolet Equinox manual prints "Use SAE 0W-20 viscosity grade engine oil." and the 2026 Chevrolet Express manual "Use SAE 5W-30 viscosity grade engine oil." None of the three prints the list of grades not to use. Our reading: three manuals cannot tell us whether GM changed its position or only its wording. Our advice: a 2014 manual should not be used for a newer car, or the other way round. All three newer manuals do print "Failure to use the recommended engine oil or equivalent can result in engine damage not covered by the vehicle warranty."

Where 10W-30 is printed as the grade, the stand-in or a chart line

Five makers print 10W-30 as a grade, a stand-in or a chart line, and they do not agree on its place.

Ram, 2022 2500 and 3500, 6.7L diesel: the recommended grade, with a temperature condition. The engine fluids table for the diesel engine says: "In ambient temperatures above 0°F (-18°C), we recommend using 10W-30 engine oil such as Mopar®, Shell Rotella and Shell Rimula that meets the manufacturer Material Standard MS-10902 and the API CK-4 engine oil category is required." Below 0°F (-18°C) it recommends 5W-40 synthetic engine oil under the same standard and category. The line asks for an API diesel category (CK-4) as well as the grade, so the grade alone does not meet it. The same manual's table for the 6.4L gasoline engine prints a different thing: "We recommend using Mopar® API Certified SAE 0W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-A0921." That is a 0W-40, which has the hot grade of a 10W-40 and a different cold grade.

Toyota, 2015 Tacoma, 4.0L V6: a stand-in with a deadline. The grade is SAE 5W-30. The manual says: "If SAE 5W-30 is not available, SAE 10W-30 oil may be used. However, it should be replaced with SAE 5W-30 at the next oil change." The same manual's 2.7L stand-in (5W-20 for 0W-20, with "must" in place of should) is covered in the oil viscosity chart guide. The 4Runner manual OM35A83U (model year not printed in the text; the file is dated February 2015) prints SAE 0W-20 with the same 5W-20 stand-in and no 10W-30.

Mazda: 10W-30 under the heading for other markets, in three manuals. The 2021 CX-5 manual has a page headed Except U.S.A., Canada. For the SKYACTIV-G 2.5T it prints "Use SAE 5W-30 engine oil. If SAE 5W-30 engine oil is not available, use SAE 0W-30 or SAE 10W-30 engine oil." The 2025 CX-50 manual has the same kind of sentence under a (Mexico) label below the heading Except U.S.A., Canada in the right-hand column of the same page: "Use API SM or higher, SAE 5W-30 engine oil. If SAE 5W-30 engine oil is not available, use SAE 5W-20, SAE 0W-30 or SAE 10W-30 engine oil." On the same page the text for the US 2.5T reads "Only use SAE 5W-30 oil “Certified For Gasoline Engines” by the American Petroleum Institute (API)." So within one manual the US text has no 10W-30 and the Mexican text allows it. The 2023 MX-5 manual goes a step further: under its (Mexico) label, 10W-30 is the first choice, "Use API SM or higher, or SAE 10W-30 engine oil. If SAE 10W-30 engine oil is not available, use SAE 5W-30, 0W-30 or 5W-20 engine oil." Its picture shows a bar labelled 10W-30 on a printed scale from -40 to 40 °C; we read it by eye and give no end points.

Genesis, 2019 G70 (a US manual): a chart. The Recommended SAE viscosity number page has a Temperature Range for SAE Viscosity Numbers chart. For the 2.0 T-GDI engine it shows bars labelled 20W-50, 15W-40, 10W-30 and, across the whole scale, 0/5W-30 and 5W-40; for the 3.3 T-GDI, 10W-30 and 5W-30. We read the 10W-30 bars as starting in the cold half of the scale and running to the hot end, with no exact temperatures. Footnotes recommend SAE 0W-30 (ACEA C2 or above) for the 2.0 and 5W-30 for the 3.3 for better fuel economy, and add "However, if the engine oil is not available in your country, select the proper engine oil using the engine oil viscosity chart."

Kia, DL3 2020 (online manual, UK English). The Recommended SAE viscosity number page lists 20W-50, 15W-40, 10W-30, 5W-20 and 5W-30 for the Nu 2.0 MPI outside Europe, the Middle East and India, and 20W-50, 15W-40, 10W-30, 0W-20, 5W-20, 0W-30 and 5W-30 for the Smartstream G2.5 outside the Middle East and India. It carries the same sentence about other viscosities as the 2023 Hyundai and Genesis manuals below. It is a UK-English page filed under model code DL3 that does not name the model, so a US owner should not read it as a rule for a US car. A second saved Kia online page (document id 77877899, no model named) lists 10W-30 for a gasoline 1.5 engine outside the Middle East and, for a (Diesel) 1.5 VGT whose chart gives no market, the entries "10W-30/40" and "5W-30/40". Our reading: 10W-30/40 means 10W-30 and 10W-40, and this is the one place in the documents we read where a 10W-40 appears as an allowed grade.

Our reading of the five: 10W-30 is the first choice only for a diesel truck (Ram) and one Mazda's Mexican-market sentence, a stand-in in Toyota's and two other Mazda manuals, and one bar among several in the Genesis and Kia charts. None prints a blanket permission to use it.

Makers that print one grade and a general warning

The other documents we read (the 2023 Hyundai and Genesis GV70 manuals, Nissan, Infiniti, Subaru, Mercedes-Benz, MINI and Honda) print the grade for the engine, sometimes with a stand-in; Hyundai, the GV70, Nissan, Infiniti and Subaru add a sentence that rules out other viscosities in general, Mercedes-Benz says to use only one class, and MINI and Honda point to a sign or a chart. They do not name 10W-30 or 10W-40, and the general sentences are the nearest thing they have to a statement about them.

Hyundai and Genesis, 2023 models (Santa Fe, Elantra, GV70). The Santa Fe chart shows 0W-20 and 0W-30, the Elantra 0W-20 and the GV70 0W-30. All three print "Using oils of any viscosity other than those recommended could result in engine damage." The same paragraph explains the trade-off in the maker's words: "Lower viscosity engine oils can provide better fuel economy and cold weather performance, however, higher viscosity engine oils are required for satisfactory lubrication in hot weather."

Nissan, 2026 Rogue, and Infiniti, 2025 QX60. Both print "Genuine “NISSAN Motor Oil 0W-20 SP” (or equivalent) is recommended." (Infiniti's page names the Nissan oil too), allow a synthetic 0W-20 GF-6A SP oil if the genuine oil is not available, and then say: "Damage caused by the use of motor oil (or engine oil) other than as recommended is not covered under NISSAN’s New Vehicle Limited Warranty." Infiniti's version names INFINITI’s New Vehicle Limited Warranty. The engine oil section of both adds "Choosing an oil viscosity other than that recommended could cause serious engine damage."

Subaru, manual MSA5M2403A. The caution reads "Use only engine oil with the recommended grade and viscosity." The table says "0W-20 synthetic oil is the required oil for optimum engine performance and protection." and allows two stand-ins in one cell, conventional oil if synthetic is unavailable and, quoted here, "If 0W-20 synthetic oil is not available, 5W-30 conventional oil may be used if you need to add oil. However, you should change to 0W-20 synthetic oil at the next oil change."

Mercedes-Benz, 2022 C-Class. "Gasoline engines: Only use SAE 0W-20 viscosity class engine oils." MINI, 2025 Countryman. "The suitable viscosity grade is indicated on a sign in the engine compartment." Honda, 2026 HR-V and 2013 Civic (Canada). The HR-V page shows one bar for 0W-20 in each of two charts, genuine oil and commercial oil, on a printed scale from -30 to 40 °C, and the Civic manual prints 0W-20 oil with an API Certification Seal.

Our reading: these manuals tell an owner to use a particular grade, Hyundai, Genesis, Nissan and Infiniti say that another viscosity can cause damage or is not covered, Subaru says to use only the recommended grade and viscosity, and that is as close as they come to answering the question of this guide. Apart from GM's 2014 list and these general sentences, none of them says whether 10W-30 or 10W-40 is acceptable.

Temperature statements, as the manuals print them

The printed temperature statements are of two kinds. The first is a condition attached to a grade. Ram's diesel manual ties 10W-30 to ambient temperatures above 0 °F (-18 °C) and 5W-40 to those below, and GM's manuals (the 2014 Cruze, Silverado, Volt, ATS and Malibu, and the 2025 Silverado and 2026 Express) tie a lower cold grade (0W-20 or 0W-30, depending on the manual) to areas of extreme cold, where the temperature falls below −29 °C (−20 °F).

The second kind is a chart, a bar for each grade against a printed temperature scale (Toyota, Honda, Mazda, Genesis, Kia, Hyundai and Subaru, among the manuals we read). The Hyundai group says: "When choosing an oil, consider the range of temperature your vehicle will be operated in before the next oil change. Proceed to select the recommended oil viscosity from the chart." We do not turn the bars into a table of temperatures, because they are pictures with no printed end points, and we offer no chart of our own, because no source we read prints one for cars in general.

Where 10W-40 shows up, and where it does not

In the manuals we read, 10W-40 appears almost nowhere. In GM's 2014 Cruze, Silverado, Volt and Cadillac ATS manuals it is a grade not to use, and we did not find it as a recommended, allowed or stand-in grade for a gasoline engine in any manual. A 40 does appear: the Ram manuals print 0W-40 for the 6.4L gasoline engine of the 2022 2500 and 3500 and for the 3.0L High Output of the 2026 1500, 5W-40 for the cold-weather diesel, and Genesis's and Kia's charts list 5W-40 and, for gasoline engines, 15W-40 and 20W-50. Our reading: those carry the hot grade of a 10W-40 with a different cold grade, and none of them is a 10W-40. Whitby's own pair is a 0W-20 and a 0W-40, which share a cold grade and, in his words, have similar low-temperature flow properties. The one exception we found is the Kia diesel chart described above.

Oil companies treat 10W-40 as a product they sell; what Castrol and Motul say about it is historical or conditional. Castrol's viscosity grades page says: "In the past, it was common for vehicles to require higher viscosity oils such as 20W-50’s, 10W-40’s and 10W-30’s." Castrol's 10W-40 page lists EDGE and GTX products, and Phillips 66 lists 10W-40 among the viscosities of two of its synthetic blend lines. Motul's page, written for Malaysia, says "In hotter environments, a 10W-40 oil may offer better stability under sustained heat." Our reading: a product page shows that an oil is sold, and a manual shows whether the engine takes it, and the manuals we read that print a grade for a gasoline engine do not include 10W-40.

Can you switch between them? What the manuals say about a different grade

The documents answer this question in four different ways. None of the four says that 10W-30 and 10W-40 are interchangeable, and none says the opposite in as many words except GM's 2014 lists in the Cruze, Silverado, Volt and Cadillac ATS manuals.

The maker says not to use them. GM's 2014 Cruze, Silverado, Volt and Cadillac ATS manuals: "Do not use other viscosity grade oils such as SAE 10W-30, 10W-40, or 20W-50."

The maker says to use only the printed viscosity, or that another can do harm. Hyundai, Genesis and Kia: "Using oils of any viscosity other than those recommended could result in engine damage." Nissan and Infiniti: "Choosing an oil viscosity other than that recommended could cause serious engine damage." Nissan's and Infiniti's pages add that damage from other oil is not covered under their new vehicle limited warranties. Subaru: "Use only engine oil with the recommended grade and viscosity." Mercedes-Benz in the 2022 C-Class: "Gasoline engines: Only use SAE 0W-20 viscosity class engine oils." These sentences do not name 10W-30 or 10W-40. Our reading: for the makers that print one grade, any grade that is not the printed one is another viscosity in these sentences (the Genesis G70 and Kia charts list several grades per engine).

The maker names a stand-in and a condition. Toyota's 2015 Tacoma says that if SAE 5W-30 is not available, SAE 10W-30 may be used for the 5W-30 engine, and that "it should be replaced with SAE 5W-30 at the next oil change." Mazda's CX-5 and CX-50 sentences allow 10W-30 if 5W-30 is not available, in the text for other markets. Subaru's table allows 5W-30 conventional oil "if you need to add oil" and asks for a change back to 0W-20 synthetic. GM's 2014 ATS manual says SAE 0W-20 "may be used as an alternative." The stand-ins we read move the cold grade (5W-30 to 10W-30, 0W-20 to 5W-20), lower the hot grade (the CX-50's 5W-20, and the ATS's 0W-20 if it applies to the 5W-30 engines, which the manual does not say) or, in Subaru's case, move from a 0W-20 synthetic to a 5W-30 conventional oil for topping up, which changes the cold grade, the hot grade (20 to 30) and the oil type; none of the stand-ins we read goes from a 30 to a 40.

The maker ties the grade to the temperature. Ram's 2022 diesel manual recommends 10W-30 above 0 °F and 5W-40 below. The grade changes with the weather by the maker's own table.

Our reading of the four: no manual we read says that a 10W-40 may replace a 10W-30, or the reverse, in a gasoline engine, and the only sentence about the pair as a pair for a gasoline engine is GM's prohibition (one Kia diesel chart lists 10W-30/40 as one entry). Our advice, not a maker's: if your manual prints one grade, that grade is the answer; if it prints a stand-in, use it only under the condition printed, and note the deadline; if your manual says nothing about either oil, ask your maker's dealer with your VIN before buying a grade the manual does not print.

Three voices that are not car makers, an author, a presenter and an oil company, say something about switching, and we mark each as theirs. Holdmeyer, retired from Chevron Lubricants, writes in STLE's magazine that engines in extreme heat or under heavy load may benefit from a higher SAE grade, and that he would not recommend a lower viscosity grade than the OEM's; Motul's page answers its FAQ on switching with "Only if it meets your vehicle’s specifications." (the full quotations are in the oil viscosity chart guide). Fenske, of Engineering Explained, who in EngineLabs's words partnered with Mobil 1 in 2020 to discuss ultra-thin oils, is quoted: "Generally speaking, lowering the hot rating of your oil is bad. Going the other direction and increasing the hot rating from your recommended oil isn’t as bad, but is still not recommended. If you are putting excessive heat into the oil, like at track days, a higher hot number can be indicated in those situations." The hot rating is the second number, so for a 10W-30 engine that is the step from 30 to 40. Those are an author's, a presenter's (see the Mobil 1 partnership above) and an oil company's views, not measurements and not a maker's instruction.

Can you mix 10W-30 and 10W-40?

We found no manual that says whether two different grades may be mixed in one engine. The one mixing sentence we read is Subaru's, in manual MSA5M2403A, and it is about brands: "When adding oil, different brands may be used together as long as they are the same ILSAC and API classification and SAE viscosity as those recommended by SUBARU." It makes the same SAE viscosity a condition and does not address mixing two grades. Our advice, not a maker's: do not read it as permission to blend a 10W-30 with a 10W-40; ask your maker's dealer with your VIN.

5W-30 vs 10W-30: what is the difference

5W-30 against 10W-30 is a different comparison from 10W-30 against 10W-40: the hot grade is the same, 30, and the cold grade differs, so the cold test separates the two oils.

By the J300 table as Wikipedia prints it, a 5W oil must pass a cold-cranking limit of at most 6,600 cP at -30 °C and a pumping limit of at most 60,000 cP at -35 °C, and a 10W oil a limit of at most 7,000 cP at -25 °C and a pumping limit of at most 60,000 cP at -30 °C. Per Wikipedia's rule, an oil that passes the 5W test and fails the 0W test is a 5W oil and cannot be labelled 10W, so a 5W-30 and a 10W-30 are two classes of cold behaviour with one hot grade.

Castrol puts the difference in plain words on its viscosity grades page: "So a 5W-30 will flow easier than a 10W-30 at start-up temperatures and a 10W-30 will flow easier than a 10W-40 at normal engine operating temperatures." It adds: "If we compare a 5W-30 and a 10W-30, they will behave very similarly as the engine heats up, but at start-up, the 5W-30 will provide less resistance and start easier than the 10W-30." Fenske's comparison in the EngineLabs report runs in the same direction, and it goes further: "For the cold rating, if you went from a 10W-30 to a 5W-30, you aren’t really changing much, since the entire viscosity range of 5W-30 is within the 10W-30 specifications. On the other hand, going from a 5W30 to a 10W-30 will have your engine seeing a much thicker oil on startup, with no benefits at operating temperature." That is a presenter's statement; the table's 5W and 10W limits are set at different temperatures, so we cannot confirm its first sentence and leave it as his claim. Holdmeyer, writing for STLE, warns about the winter grade in the same direction as the step from 5W to 10W: "Using a higher SAE “W” viscosity grade could cause great harm if the oil cannot flow through the engine in cold climates." That is an author's view, not a maker's.

The manuals make the direction of the switch visible. Toyota's 2015 Tacoma and Mazda's CX-5 and CX-50 texts for other markets list 5W-30 as the grade and 10W-30 as the stand-in, and Mazda's 2023 MX-5 Mexico text reverses the order. GM's 2014 Cruze, Silverado, Volt and Cadillac ATS manuals list 5W-30 as the best grade for some engines and tell the owner not to use 10W-30. So the same pair of oils is a grade, a stand-in and a prohibited oil in different documents, and the engine, the year and the market are the difference.

A government source puts a number on one of these switches. The US Department of Energy's fueleconomy.gov page, in its section on using the recommended grade of motor oil, says: "For example, using 10W-30 motor oil in an engine designed to use 5W-30 can lower your gas mileage by 1%–2%." The page's data note names a 2001 report as the basis of its motor oil estimates, and the page carries a revision date of June 27, 2016, so the figure is dated, and the page is about mileage, not about wear or protection.

The mark on the bottle is not the viscosity: API, ILSAC and 10W-40

A bottle carries two kinds of information that the label 10W-30 or 10W-40 does not cover: the performance mark and the viscosity. The viscosity is the part this page has covered. The performance mark, the API (American Petroleum Institute) Starburst or Donut symbol and the ILSAC carmakers' standard behind the Starburst, is a separate requirement, and it interacts with the grade in a way that matters for 10W-40.

Four sources list which grades carry the mark, and two of them, Kendall and Phillips 66, name 10W-40. Kendall, a Phillips 66 brand, says in its one-page note on the new ILSAC GF-7 standard that oils meeting the ILSAC GF-7A and API SQ standards, such as 0W-20, 5W-20, 5W-30 and 10W-30, will feature the starburst icon. It continues: "Heavier grades like 10W-40 and 20W-50 meet API SQ requirements but do not qualify for ILSAC certification and will not carry a starburst or shield." Phillips 66's GF-6 page says of the previous standard: "Heavier grades like 10W-40 and 10W-50 are certified to the API SP standard only and do not carry an ILSAC certification mark." Chevron's Havoline page on GF-7 says GF-7A is designed for commonly used grades "like SAE 0W-30, 5W-30, 10W-30, 0W-20, and 5W-20." Holdmeyer's 2024 article lists the grades allowed the starburst under the previous standard, GF-6A: "SAE 0W-20, SAE 0W-30, SAE 5W-20, SAE 5W-30 and SAE 10W-30". Ram's 2026 manual prints sentences of the same kind, with its own lists of grades that name neither 10W-30 nor 10W-40: "The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils." and "The API Donut trademark certifies 0W-40 and 5W-40 engine oil."

Our reading of those documents together: a 10W-30 can carry the Starburst, and a 10W-40 is an API oil that cannot, by Kendall's and Phillips 66's accounts, and Holdmeyer's list, which says the mark is limited to those grades, and Havoline's examples do not include it (our reading). That matters when a manual asks for a mark and not only for a grade. Hyundai's Santa Fe manual says of the ILSAC mark: "It is recommended to only use engine oils that uphold this API Certification Mark." Mazda's CX-50 text for the US 2.5T asks for oil "Certified For Gasoline Engines" by the API, and Honda's HR-V manual for "API service SN or higher grade" and the Starburst. For a car whose manual requires the Starburst, a 10W-40 could not meet that requirement because of the mark, whatever its viscosity. For the diesel of Ram's 2022 manual the mark is API CK-4, and the manual ties both of its diesel grades, 10W-30 and 5W-40, to that category.

Castrol says where to look on the bottle: "Always check the motor oil container for the specifications that the motor oil meets – it will likely be found on the back label of the oil container." What your car takes in specification terms (API, ILSAC, dexos) is covered in the guide to what oil your car takes; this page only notes that a bottle can have the right viscosity and the wrong mark.

Fuel economy, heat and load: what is claimed, and by whom

Almost everything said in favour of a higher or a lower hot grade is a claim about fuel economy, heat or load. The table sets the claims side by side with the source named; Toyota's and Holdmeyer's statements on heat and load are set out in the oil viscosity chart guide. They are statements by their authors, and none puts a number on the step from a 30 to a 40.

Hyundai, Genesis, Kia manuals. "Lower viscosity engine oils can provide better fuel economy and cold weather performance, however, higher viscosity engine oils are required for satisfactory lubrication in hot weather."
Maker: trade-off
TotalEnergies UK. A higher grade "means optimized component protection and engine sealing"; a lower number "will be more effective in reducing friction between hot parts and improve fuel consumption."
Oil company: trade-off
Castrol. "Thick, high viscosity oils are typically better at maintaining film strength to protect engines at high temperatures."
Oil company: film strength

The claims agree on the direction: a thicker oil holds a film better when hot, and a thinner one saves fuel. The makers' sentences come with a grade for the engine: the Hyundai-group paragraph sits directly above the chart that prints the recommended grade, and Toyota's sentence on a higher second number sits on the same page as its stand-in rule. Our reading: apart from Subaru's stand-in for topping up and the Genesis G70 and Kia charts, which list 40 and 50 grades by temperature, the manuals we read do not license an owner to move the hot grade up.

Older and high-mileage engines: what we found and did not find

A claim heard at counters is that 10W-40 suits older or high-mileage engines better than 10W-30. We found no car maker statement that says so. The manuals we read print a grade for the engine without a mileage condition, and the stand-in sentences carry conditions of availability, not of mileage.

What we found are statements by oil companies. Motul's page says: "Higher numbers provide a stronger protective film under heat and load, which can be important for heavier vehicles, older engines, or spirited driving." Castrol's viscosity grades page, quoted above, notes that vehicles in the past commonly required 10W-40 and 10W-30, and its grade pages list High Mileage products, EDGE High Mileage and GTX High Mileage, in both 10W-30 and 10W-40. A product line is a product statement, and the pages do not say what viscosity a particular high-mileage engine needs.

Our advice, not a maker's: a worn engine is not diagnosed by the label on the bottle. If an engine uses oil or leaks it, see the guides on oil leaks and the low oil pressure warning, and ask your maker's dealer for the grade for your VIN.

At the counter or the shop: what to say, and what a good answer sounds like

Which oil grade should go in the car, and who decides if the shelf says 10W-40 and the manual says something else? In short, by our reading of the documents above (this PulsCar guide sells no oil): the manual for your engine decides, the 10W part is the same in both oils and the hot grade differs, and the manuals we read name 10W-30 in a few places and 10W-40 in GM's 2014 lists of grades not to use and on one Kia diesel chart; none of the gasoline manuals we read allows it, and Ford's could not be read. If a shop or shelf sign offers a grade your manual does not print, ask for the manual's line; treat a stand-in as printed, with its condition and any deadline. Where a manual prints the grade for your engine and warns about other viscosities, as Hyundai, Genesis, Kia, Nissan, Infiniti, Subaru and Mercedes-Benz do, the printed grade is the answer.

Our advice, not a maker's, is to carry the grade and the specification from your manual to the counter and to ask three questions. Which viscosity grade is on the bottle, and does it match the manual's line for my engine? Which API or ILSAC mark is on the bottle, and does the manual ask for one? If the shop recommends a different grade, where does that recommendation come from: the maker's manual or the shop's own rule of thumb? A good answer names a document; a weaker answer is a rule of thumb about mileage, because the only sources we read that make that claim are oil companies, not makers; the makers' statements about climate and load come with the grade printed for the engine.

If the red oil pressure light comes on

The grade of the oil is a separate question from the red oil pressure light, but the rule is stated in full here and repeated in the action plan. If the red oil pressure light comes on while you drive, stop in a safe place and switch the engine off, and do not run the engine with the light on: Subaru prints a caution not to operate the engine with that light on, Mazda's 2021 CX-5 manual one not to run the engine if the oil pressure is low, Nissan and Infiniti say to stop the engine immediately, and GM's 2014 manuals say not to operate the vehicle until the cause of the low oil pressure has been corrected. Mazda (2025 CX-50), Nissan, Infiniti and Subaru say to contact their dealer or an authorized repair shop. Mazda's 2021 CX-5 manual says to wait 5 minutes, inspect the oil level, add oil if it is low, and have the car towed to a Mazda dealer if the light stays on. GM's 2026 Equinox manual says, as GM's own statement and not our advice, to add oil if the level is low and restart, and, if the light stays on for more than 10 seconds, to turn the vehicle off again, not restart it and see their dealer. Our advice, not a maker's: if your own manual says nothing more, once it is safe check the oil level; if it is low, add oil as your manual says, and if the level was not low, or the light stays on after adding oil or returns, do not drive on and have the car towed. The causes of the light are covered in the guide to the low oil pressure warning.

Two composite situations

These are composite scenarios, not individual customers. They are built only from statements printed in the documents above, and each shows where the manual decides.

The shop offers 10W-40 for a 2014 Chevrolet Cruze. An owner is told that a thicker oil suits a car with many miles on it. The 2014 Cruze manual says "SAE 5W-30 is the best viscosity grade for the vehicle. Do not use other viscosity grade oils such as SAE 10W-30, 10W-40, or 20W-50." The claim about thicker oil is one we found only from oil companies, and the maker's manual prints a prohibition. The step that fits the documents is to ask for the manual's grade, and to ask the maker's dealer if the shop has a reason to differ.

The shop is out of 5W-30 for a 2015 Toyota Tacoma with the 4.0L V6. The shelf has 10W-30. The manual says "If SAE 5W-30 is not available, SAE 10W-30 oil may be used. However, it should be replaced with SAE 5W-30 at the next oil change." The documents allow that stand-in under that condition and say nothing that extends it to a 10W-40.

Your action plan

Our advice, not a maker's, in five steps.

  1. Find the line for your engine in your owner's manual, in the section on recommended fluids, lubricants or specifications (no manual: check the oil filler cap or an under-hood label, or the maker's online manual for your VIN). Note the viscosity grade, the specification mark (API, ILSAC, dexos or a maker's own), and any condition such as a temperature or a market heading. Check the country heading: a sentence under Except U.S.A., Canada, or under a (Mexico) label, is not written for a US car.
  2. If the manual names a stand-in, write down its condition and, where printed, its deadline. If it names none, the printed grade is the only one. If your manual has a sentence like GM's 2014 one, "Do not use other viscosity grade oils such as SAE 10W-30, 10W-40, or 20W-50", or says that another viscosity could result in engine damage, treat the printed grade as the only grade.
  3. At the counter, compare the bottle with the manual's line: the viscosity grade and the performance mark. Kendall and Phillips 66 say a 10W-40 cannot carry the ILSAC mark, and Holdmeyer's list of grades for the previous standard does not include it (our reading). Our advice: a manual that asks for the starburst asks for a different bottle.
  4. If a shop or a website suggests a different grade, treat that as a pointer to check against the manual. Our advice: ask your maker's dealer, with your VIN, for the grade for your engine.
  5. If the red oil pressure light comes on while you drive, stop in a safe place and switch the engine off, and do not run the engine with the light on: Subaru prints a caution not to operate the engine with that light on, Mazda's 2021 CX-5 manual one not to run the engine if the oil pressure is low, Nissan and Infiniti say to stop the engine immediately, and GM's 2014 manuals say not to operate the vehicle until the cause of the low oil pressure has been corrected. Mazda (2025 CX-50), Nissan, Infiniti and Subaru say to contact their dealer or an authorized repair shop. Mazda's 2021 CX-5 manual says to wait 5 minutes, inspect the oil level, add oil if it is low, and have the car towed to a Mazda dealer if the light stays on. GM's 2026 Equinox manual says, as GM's own statement and not our advice, to add oil if the level is low and restart, and, if the light stays on for more than 10 seconds, to turn the vehicle off again, not restart it and see their dealer. Our advice, not a maker's: if your own manual says nothing more, once it is safe check the oil level; if it is low, add oil as your manual says, and if the level was not low, or the light stays on after adding oil or returns, do not drive on and have the car towed.

Which makers allow 10W-30 or 10W-40, and what does that mean for a driver who wants a yes or a no? By our reading (this PulsCar guide sells no oil): the two oils share the 10W cold grade and differ in the hot grade, and in the thirteen makers' documents we read, GM's 2014 Cruze, Silverado, Volt and Cadillac ATS manuals say not to use either grade, Ram's 2022 diesel manual recommends 10W-30 above 0 °F, Toyota and Mazda allow 10W-30 as a stand-in or for some markets, Genesis and Kia print it on charts, and none of the manuals we read names 10W-40 as allowed for a gasoline engine (a Kia diesel chart lists 10W-30/40; Ford's could not be read). Hyundai, Nissan, Infiniti, Subaru, Mercedes-Benz and Honda print other grades, and MINI points to a sign in the engine compartment. Only the list in your own manual, for your engine, year and country, applies to your car.

What we could not read

We could not read Ford's owner's manuals: the host we tried answered 403 on 17 November 2026. We did not find a readable manual text with the engine oil grade for Volkswagen, Audi, BMW (apart from the MINI manual), Volvo or Mitsubishi. The Mobil, Valvoline, Pennzoil and AMSOIL viscosity pages we tried answered 403 or 404, and Petro-Canada's lubricant handbook answered 429. The SAE J300 standard itself is sold by SAE and was not read, so the grade limits come from Wikipedia's article, Olezol's table and two articles in STLE's magazine. The chart bars in the manuals are pictures, and we read them by eye. The two J300 tables we used, Wikipedia's (which cites the April 2021 edition) and Olezol's (January 2015 revision), disagree on the HTHS limit for grade 40 (see the HTHS rows above), and we did not resolve that.

What this page cannot tell you

It cannot tell you the grade for your car. Only the manual for your engine, model year and country, or your maker's dealer with your VIN, can. We read thirteen makers' documents, one to several models of each, so many makes, models and years are not here, and an older or newer manual may say something different, as GM's 2014 and 2025 manuals do. We did not test oils, do not rank them and make no claim that either grade is better. We found no source that quantifies the step from a 30 to a 40 in fuel economy, wear or cold starting; the nearest figure is for a different step, 1% to 2% for 10W-30 in an engine designed for 5W-30 (Department of Energy). The oil-company, author and government pages are statements by their authors, and the one trade report (EngineLabs on a Mobil 1 partnership) reports a presenter's view. It does not say whether to drain an oil you have already added; ask your maker's dealer.

Sources and documents

Manuals and web pages were read, or read again, on 17 November 2026. Where a page carried no date or did not name the model year, we say so.

  1. SAE J300 and its grades: Wikipedia, SAE J300 (an encyclopedia article that cites the April 2021 edition); Olezol, SAE J300 Standard for Engine Oil Viscosity Grades (a table described as the January 2015 revision); R. David Whitby, Engine oil viscosity, TLT Worldwide, January 2017, Society of Tribologists and Lubrication Engineers; Dan Holdmeyer, Automotive engine oil specifications, TLT Lubrication Fundamentals, August 2024.
  2. Oil companies, each their own statement: Castrol, Oil viscosity grades explained, 10W-30 and 10W-40; TotalEnergies UK, Motor oil viscosity grades explained; Motul, What do engine oil numbers mean (Malaysia page); Phillips 66 Lubricants, GF-6 Engine Oil Standards Explained and Kendall, Introducing the GF-7 standard, one-page note; Chevron Lubricants, Havoline GF-7 motor oils (undated).
  3. Government and trade press: US Department of Energy, fueleconomy.gov, Keeping Your Vehicle in Shape (the page's own data note says revised June 27, 2016); EngineLabs, Three Questions About Ultra-Thin Oil With Engineering Explained, 4 September 2020.
  4. General Motors, 2014 owner's manuals: Chevrolet Cruze, Silverado, Volt and Malibu; Cadillac ATS. Chevrolet owner's manuals: 2025 Silverado 1500, 2026 Equinox and 2026 Express (a copy hosted by a third-party site).
  5. Ram: 2026 1500 owner's manual and the 2022 2500 and 3500 engine fluids and lubricants page.
  6. Toyota, owner's manuals: 2015 Tacoma, OM04009U, hosted by Toyota Canada and 4Runner OM35A83U. Honda: 2026 HR-V owner's manual, a copy hosted by a dealer and the 2013 Civic manual, Honda Canada.
  7. Mazda, owner's manuals: 2021 CX-5, 2023 MX-5 and 2025 CX-50 (the page edition is dated 2024).
  8. Hyundai, 2023 Santa Fe and 2023 Elantra owner's manuals; Genesis, 2023 GV70 and 2019 G70; Kia, Recommended SAE viscosity number, online manual model code DL3, 2020, UK English and a second Recommended SAE viscosity number page, document id 77877899, model not named.
  9. Nissan, 2026 Rogue; Infiniti, 2025 QX60; Subaru, owner's manual MSA5M2403A (most pages marked as edited in December 2022); Mercedes-Benz, 2022 C-Class; MINI, 2025 Countryman manual.
  10. What we could not read, and so did not quote: Ford's owner's manuals; the grade pages of Volkswagen, Audi, BMW (apart from the MINI manual), Volvo and Mitsubishi; Mobil, Valvoline, Pennzoil and AMSOIL viscosity pages; Petro-Canada's handbook; the SAE J300 standard.
  11. PulsCar homepage (publisher).

Prices verified: this page carries no prices; see the oil change cost guide · Technical documents verified: November 2026

Saw a figure or a source that differs from this page? Email [email protected] with the source and its date.