💡 The answer in 60 seconds

In 0W-20, two numbers do two jobs, and your manual chooses the pair for your engine. The number before the W (winter) is a cold-start grade: a 0W oil must pass a cold-cranking limit of 6,200 mPa·s at -35 °C. The number after the dash is a hot grade: grade 20 means a viscosity of 6.9 to under 9.3 mm2/s at 100 °C. Lower numbers are thinner in those tests. They are labels for ranges, not weights and not quality scores. No maker we read prints one chart for all cars: Hyundai's 2023 Santa Fe prints 0W-20 for one engine and 0W-30 for another, Mazda's 2021 CX-5 prints 0W-20 and 5W-30 for two petrol engines, Ram's 2026 1500 prints 0W-20 and, for one engine, 0W-40, and Mercedes-Benz's 2022 C-Class says to use only SAE 0W-20 in its gasoline engines. Can you use a different grade? Our advice: only one your manual names as a stand-in, under its condition. Toyota and Subaru say to switch back at the next oil change, and Toyota words one stand-in with must and the other with should. What to do: find the line for your engine, year and country in your manual, and use it. If the red oil pressure light comes on while you drive, go straight to the section on the red oil pressure light.

PulsCar publishes this guide; it sells no oil, parts or servicing, and no link on this page is an affiliate link. Every maker statement below is a printed figure or sentence for the model, engine and year named, read on 11 November 2026 (the Elantra and Mercedes-Benz GLE copies on 12 November; chart pictures re-read from the same documents, and the Kia viscosity page, the Wikipedia, tribology-society, trade-press, Department of Energy and most oil-company pages, on 15 November 2026), and none of them is for your car unless it matches. This page answers one question: what the grade numbers mean, and what makers print about grades, temperature charts, stand-ins and using another grade. It does not repeat which oil your car takes and where to look it up (see what oil your car takes), the difference between synthetic and conventional oil (see synthetic versus conventional oil), how often to change oil (see how often to change oil), the steps of the job (see how to change oil) or what it costs (see the oil change cost guide). This page does not test or rank oils, so there is no best oil here and no chart of our own that says which grade to buy at which temperature.

What do the numbers in an oil grade like 0W-20 mean, and what do car makers print about them? In short, by our reading of the tables (PulsCar publishes this guide and sells no oil): 0W-20 is thinner than 5W-30 in both the cold and the hot test, so a swap changes both numbers. SAE J300 gives each grade limits: a cold-cranking and pumping limit for the part before the W, a viscosity range at 100 °C and a minimum at 150 °C under high shear for the part after it. A multigrade oil such as 0W-20 must meet both parts. Makers then pick a grade for each engine and, except MINI, print it: 0W-20, 0W-30, 5W-30 or 0W-40 in the manuals we read, sometimes with a chart or a stand-in. None says a bigger number is simply better. Your manual's line for your engine is the answer; this page explains what the line says.

What the two numbers in 0W-20 mean

The grading system is SAE J300, a standard kept by SAE International. It covers engine oils only; SAE keeps a separate rating system for gear and axle oils, and Wikipedia's article on J300 warns that the two should not be confused, because a gear oil number like 75W-140 does not mean more viscosity than an engine oil 20W-50. The J300 document itself is published by SAE and was not read; the figures on this page come from Wikipedia's article, which cites the April 2021 edition, checked against an article by R. David Whitby in STLE's magazine TLT and against what oil companies print.

A multigrade grade has two parts. Castrol, an oil company, describes it this way: "The properties of the oil at lower temperatures define the first part of the motor oil grade." The W stands for winter. In its words, "The better the oil performs at lower temperatures, the lower the number before the W." The second part is about heat: "The “20” portion of the 0W-20 grade relates to how the oil flows through the engine at higher temperatures", which Castrol compares to a warmed-up engine on a highway. TotalEnergies, another oil company, puts the same pair in everyday words on its UK page: the number before the W is "the winter viscosity grade" and the value after it is the grade at high temperatures. Motul, an oil company that publishes a page in Malaysia, calls the two numbers cold-start viscosity and hot-temperature viscosity.

Whitby, writing for the tribology society, adds the point that stops the numbers being mistaken for measurements: "They are just numbers, not viscosities." They refer to ranges of viscosity measured at defined temperatures, and an oil must fall inside the range for its grade. Castrol makes the same point about the zero: "zero doesn’t mean zero performance"; it means the oil flows more easily at low temperature than oils in the 5W, 10W and 20W ranges.

The SAE J300 limits, grade by grade

The tables below show the limits Wikipedia prints for the 2021 edition of J300. Viscosity is shown in two units that the sources use side by side: mPa·s is the same as centipoise (cP), and mm2/s is the same as centistokes (cSt). Each row is one grade; the right-hand column is a short label of the row's main limit. Our reading: the 100 °C ranges of grades 8, 12, 16 and 20 overlap, and the HTHS minimum tells them apart.

The winter grades first. Each has a limit on cold-cranking viscosity (how stiff the oil is when the starter turns a cold engine), a limit on pumping viscosity (how readily the oil can be pumped through the engine when cold), and a minimum viscosity at 100 °C.

0W. Cold-cranking viscosity at most 6,200 mPa·s at -35 °C; pumping viscosity at most 60,000 mPa·s at -40 °C; viscosity at 100 °C at least 3.8 mm2/s.
6,200 at -35 °C
5W. Cold-cranking at most 6,600 mPa·s at -30 °C; pumping at most 60,000 mPa·s at -35 °C; at 100 °C at least 3.8 mm2/s.
6,600 at -30 °C
10W. Cold-cranking at most 7,000 mPa·s at -25 °C; pumping at most 60,000 mPa·s at -30 °C; at 100 °C at least 4.1 mm2/s.
7,000 at -25 °C
15W. Cold-cranking at most 7,000 mPa·s at -20 °C; pumping at most 60,000 mPa·s at -25 °C; at 100 °C at least 5.6 mm2/s.
7,000 at -20 °C
20W. Cold-cranking at most 9,500 mPa·s at -15 °C; pumping at most 60,000 mPa·s at -20 °C; at 100 °C at least 5.6 mm2/s.
9,500 at -15 °C
25W. Cold-cranking at most 13,000 mPa·s at -10 °C; pumping at most 60,000 mPa·s at -15 °C; at 100 °C at least 9.3 mm2/s.
13,000 at -10 °C

Two of these rows are confirmed by a second source. Whitby's article gives, for every 0W oil, a cold-cranking viscosity of less than 6,200 mPa·s at -35 °C and a minimum of 3.8 mm2/s at 100 °C, and for every 20W oil less than 9,500 mPa·s at -15 °C and at least 5.6 mm2/s at 100 °C. Dan Holdmeyer, who is retired from Chevron Lubricants and wrote in the same magazine in August 2024, describes a pattern that the table shows: the pumping test temperatures are always 5 °C below the cranking test temperatures, and the maximum pumping viscosities are much higher than the cranking maxima because the two tests are run differently, the cranking test under shear and the pumping test under no yield stress.

The hot grades next. Each has a range of viscosity at 100 °C and a minimum high-temperature high-shear (HTHS) viscosity at 150 °C. Holdmeyer says the hot grades assure a lubricant film at the engine operating temperature even under high shearing conditions.

8. Viscosity at 100 °C from 4.0 to under 6.1 mm2/s; HTHS at 150 °C at least 1.70 mPa·s.
4.0 to under 6.1
12. 5.0 to under 7.1 mm2/s at 100 °C; HTHS at least 2.0 mPa·s.
5.0 to under 7.1
16. 6.1 to under 8.2 mm2/s at 100 °C; HTHS at least 2.3 mPa·s.
6.1 to under 8.2
20. 6.9 to under 9.3 mm2/s at 100 °C; HTHS at least 2.6 mPa·s.
6.9 to under 9.3
30. 9.3 to under 12.5 mm2/s at 100 °C; HTHS at least 2.9 mPa·s.
9.3 to under 12.5
40. 12.5 to under 16.3 mm2/s at 100 °C; HTHS at least 3.5 mPa·s or 3.7 mPa·s, as the table prints it.
12.5 to under 16.3
50. 16.3 to under 21.9 mm2/s at 100 °C; HTHS at least 3.7 mPa·s.
16.3 to under 21.9
60. 21.9 to under 26.1 mm2/s at 100 °C; HTHS at least 3.7 mPa·s.
21.9 to under 26.1

Whitby's article agrees on the 50 row: a viscosity at 100 °C between 16.3 and 21.9 mm2/s and an HTHS of at least 3.7 mPa·s. His sentence about grade 20, though, gives a range of 4.0 to 6.1 mm2/s next to an HTHS of at least 2.6 mPa·s, which is not what Wikipedia's table lists for that grade (4.0 to under 6.1 belongs to grade 8 there, 2.6 to grade 20), so we do not rely on that sentence. Wikipedia's account of the history explains why older tables differ: it says grade 16 was added in 2013 and that this revision "raised the minimum non-winter kinematic viscosity at 100°C from 5.6 cSt to 6.9 cSt", and that grades 8 and 12 were added in 2015. A table or chart made before the 2013 revision may therefore show a lower minimum for grade 20 than the current one.

How a grade is assigned: the coldest test an oil passes

The winter part is assigned by testing, not by labelling. Wikipedia's article describes it: "The grade of the oil is that associated with the coldest temperature at which the oil passes the test." It gives an example: an oil that passes at the 10W and 5W temperatures but fails at the 0W temperature is a 5W oil, and "It cannot be labeled 0W or 10W." The hot part is assigned from the viscosity at 100 °C and the HTHS minimum in the tables above.

A multigrade oil has to pass both. Wikipedia says that a 10W-30 "must pass the SAE J300 viscosity grade requirements for both 10W and 30". The same article says viscosity index improvers are polymer additives "usually to improve cold weather performance in passenger vehicles", and that an oil that contains them must carry a multigrade label.

What follows from the tables is not obvious from the labels, so we state it as our reading. A 0W-20 and a 0W-40 have the same cold limit and different hot ranges (grade 20: 6.9 to under 9.3 mm2/s; grade 40: 12.5 to under 16.3). Whitby says the same thing in words: "a 0W-20 oil will have similar low-temperature flow properties to a 0W-40 oil". A 5W-30 and a 10W-30 share the hot range and differ in the cold limit (6,600 mPa·s at -30 °C against 7,000 mPa·s at -25 °C). And the cold number does not rank oils by quality: Whitby writes that an oil with a cranking viscosity of 5,800 cP at -35 °C and another with 6,150 cP at -35 °C are both 0W oils.

Three ways the numbers get misread

Three mistakes come up in the pages we read, and each is corrected by a source named below.

Trap one: the W means weight. Wikipedia's article on J300 notes that in the United States the numbers are often called the weight of an oil. Oil companies correct it. Motul: "The ‘W’ stands for ‘winter’, not weight." TotalEnergies: "the ‘W’ still means ‘winter’". Castrol's page, quoted above, says the W stands for winter. The numbers are classes, so a 5W-30 does not weigh five or thirty of anything, and it does not turn from a five-weight into a thirty-weight oil when it warms up.

Trap two: the second number is how thick the oil becomes in a hot engine. EngineLabs, a trade publication, reported in September 2020 on a discussion by Jason Fenske of Engineering Explained, who partnered with Mobil 1, an oil brand, so read it as one presenter's explanation with a brand beside it. Fenske's point on the hot number: "No, that doesn’t mean the oil gets thicker as it heats up. It means that it behaves like a thicker oil, at higher temperatures". The J300 tables above say the same thing from the other side: the hot grade is a range of viscosity measured at 100 °C, not a change in the oil as it warms. The hot number tells you which range the oil falls into when it is hot.

Trap three: the same grade means the same oil, and a higher number means more protection. Whitby's article, titled Engine oil viscosity, opens: "Not all 0W-20 oils are exactly the same, nor are all 10W-40 oils, 20W-50 oils or other similar viscosity grades." Two oils of one grade can differ inside the range, and a grade says nothing about the oil's additives or its quality specification. Whitby adds: "Whether one oil is better than another one depends on what a user deems better." The grade is the viscosity part of the answer; the specification that the oil meets (API, ILSAC, dexos or a maker's approval) is a different part, covered in our guide on which oil your car takes. A bottle with the right grade and the wrong specification is not the right oil, and the reverse is also true.

Why makers specify a grade, in their own words

Makers explain the choice in a few sentences, and the explanations are similar. Between them they give three reasons: starting in the cold, protecting the engine when it is hot, and fuel economy.

Toyota's 2015 Tacoma and its 4Runner manual (OM35A83U) say of the first choice they print: "SAE 0W-20 is the best choice for good fuel economy and good starting in cold weather." They also explain the numbers, and note a condition under which a higher second number may be better: "An oil with a higher viscosity (one with a higher value) may be better suited if the vehicle is operated at high speeds, or under extreme load conditions." Toyota says may, and it says it about the number after the dash.

Hyundai, Genesis and Kia print one paragraph in their manuals, and we found it in the 2023 Santa Fe, the 2023 Elantra, the 2023 GV70 and the 2024 Kia SK3 online manual: "Lower viscosity engine oils can provide better fuel economy and cold weather performance, however, higher viscosity engine oils are required for satisfactory lubrication in hot weather." The paragraph continues with the instruction that bounds it: "Using oils of any viscosity other than those recommended could result in engine damage."

Subaru's 2403 manual words the trade-off almost the same way: "Oils of lower viscosity provide better fuel economy. However, in hot weather, oil of higher viscosity is required to properly lubricate the engine." Nissan's 2026 Rogue manual and Infiniti's 2025 QX60 manual explain temperature first: "The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be operated before the next oil change." Honda's 2026 HR-V manual says to use "a genuine engine oil or another commercial engine oil of suitable type and viscosity (for the ambient temperature) as shown in the image that follows", and the image is a temperature chart that we describe below.

Mercedes-Benz adds a fuel-economy recommendation tied to its approvals. The 2022 C-Class manual says: "To achieve the lowest possible fuel consumption, it is recommended to use the engine oil specifications marked in the table for the lowest SAE viscosity class." It continues: "While doing so, observe possible restrictions of the approved SAE viscosity classes." Our reading: the wording is a recommendation tied to the table, and the restriction is part of the approval, not an invitation to pick a thin oil from a shelf.

A government source measures the fuel-economy part. The US Department of Energy's fueleconomy.gov page on keeping your vehicle in shape says: "You can improve your gas mileage by 1%–2% by using the manufacturer's recommended grade of motor oil." Its examples: "using 10W-30 motor oil in an engine designed to use 5W-30 can lower your gas mileage by 1%–2%", and "Using 5W-30 in an engine designed for 5W-20 can lower your gas mileage by 1%–1.5%." The page's data note says that the estimates for fuel savings from using the recommended grade of motor oil are based on a 2001 report by Energy and Environmental Analysis, Inc., with a data note marked revised 27 June 2016, so they are older and general figures, not a measurement on any one car.

Our reading, which no source states in these words: the grade pages we read give reasons but no number for wear. The only number we found beside those reasons is the Department of Energy's fuel-economy estimate, and it points toward following the manual. The decision about the grade is the maker's, taken engine by engine, and the next section shows what it looks like on the page.

Thirteen makers' grade statements, side by side

Each row below is one maker's document, named by model and year, and what it prints about the grade: the grade itself, any condition, and the wording on using another. Nothing is averaged, and the right-hand column is only a short label. Quantities, specifications and warranty sentences belong to the guide on which oil your car takes, so they are mostly left out here; where a model appears in both guides, this one reads a different manual or edition or a different part of the page.

Toyota, 2015 Tacoma manual (copy hosted by Toyota Canada) and 4Runner manual OM35A83U (model year not printed in the text we read). The Tacoma's 2.7 L four-cylinder (2TR-FE) takes SAE 0W-20 and its 4.0 L V6 (1GR-FE) takes SAE 5W-30. For the first: "If SAE 0W-20 is not available, SAE 5W-20 oil may be used. However, it must be replaced with SAE 0W-20 at the next oil change." For the V6: "If SAE 5W-30 is not available, SAE 10W-30 oil may be used. However, it should be replaced with SAE 5W-30 at the next oil change." The 4Runner manual prints SAE 0W-20 with the same 5W-20 stand-in.
0W-20 or 5W-30 by engine; stand-ins
Honda, 2026 HR-V manual (dealer-hosted copy) and 2013 Civic manual (Honda Canada). The HR-V prints Honda Genuine Motor Oil 0W-20, or a commercial oil of 0W-20 with API service SN or higher grade and the API Starburst mark, each over a chart captioned Ambient Temperature. The Civic manual prints "Premium-grade 0W-20 detergent oil with an API Certification Seal on the container."
0W-20; chart by ambient temperature
Hyundai, 2023 Santa Fe and 2023 Elantra manuals. Santa Fe: 0W-20 for the Smartstream G2.5 GDI and 0W-30 for the G2.5 T-GDI. Elantra: 0W-20 for the Smartstream G2.0 Atkinson and G1.6 T-GDi. Both print "Using oils of any viscosity other than those recommended could result in engine damage."
0W-20 or 0W-30 by engine
Genesis, 2023 GV70 manual. One row, Gasoline Engine Oil, SAE 0W-30, under the same paragraph and the same sentence about viscosity other than those recommended.
0W-30
Kia, 2024 SK3 online manual (US English). The lubricants page prints "Full synthetic SAE 0W-20, API SN PLUS/SP or ILSAC GF-6" for the engine oil; the separate page headed Recommended SAE viscosity number carries the same paragraph and sentence as Hyundai's and a chart row for a 2.0 MPI gasoline engine whose bar is a picture we could not read.
0W-20; chart bar not read
Nissan, 2026 Rogue manual. The oil section shows the API service symbol with SAE 0W-20 in its centre and says: "Choosing an oil viscosity other than that recommended could cause serious engine damage."
0W-20 symbol; no chart
Infiniti, 2025 QX60 manual. The oil viscosity paragraph is word for word Nissan's, including "Choosing an oil viscosity other than that recommended could cause serious engine damage."
Same wording as Nissan
Mazda, 2021 CX-5 manual. U.S.A., Canada: SKYACTIV-G 2.5 "Use SAE 0W-20 engine oil."; SKYACTIV-G 2.5T "Use SAE 5W-30 engine oil."; each line adds Only use that grade, Certified For Gasoline Engines by API; the SKYACTIV-D 2.2 diesel takes Mazda Genuine SKYACTIV-D SAE 0W-30 Diesel Engine Oil, with "Alternative oil: ACEA C3 and SAE 0W-30 or 5W-30". Except U.S.A., Canada: SAE 5W-30.
0W-20, 5W-30 or 0W-30 by engine
General Motors, 2026 Chevrolet Express and 2026 Equinox manuals. Express: "Use SAE 5W-30 viscosity grade engine oil." Equinox: "Use SAE 0W-20 viscosity grade engine oil." The Express manual adds that where the temperature falls below -29 °C (-20 °F) an SAE 0W-30 oil may be used.
5W-30 (Express); 0W-20 (Equinox)
Ram, 2026 1500 manual. 3.0L Standard Output: Mopar SAE 0W-20 Full Synthetic. 3.6L and 5.7L: the same grade. 3.0L High Output: "Mopar® API Certified SAE 0W-40 Full Synthetic Engine Oil".
0W-20 for most; 0W-40 for one engine
Subaru, owner's manual MSA5M2403A. The manual says to always use the Subaru approved oil; in its alternative-oil table, for when that oil is unavailable, "0W-20 synthetic oil is the required oil for optimum engine performance and protection." If it is not available, 5W-30 conventional oil may be used if you need to add oil, and you should change to 0W-20 synthetic at the next oil change. The chart shows two arrows, 0W-20 and 5W-30.
0W-20 synthetic; 5W-30 stand-in
Mercedes-Benz, 2022 C-Class manual and 2022 GLE manual. C-Class, gasoline engines: "Only use SAE 0W-20 viscosity class engine oils." The GLE manual lists, per model, the MB-Approvals (for the GLE 450 4MATIC, 229.51, 229.52, 229.61, 229.71 and 229.72) and tells you to observe restrictions on the approved SAE viscosity classes.
0W-20 only (C-Class); approvals (GLE)
MINI, 2025 Countryman manual. When topping up a gasoline engine the specification is BMW Longlife-17 FE+, and the manual says: "When selecting an engine oil, make sure that the engine oil has a suitable viscosity grade. The suitable viscosity grade is indicated on a sign in the engine compartment."
Grade on a sign under the hood

Four things stand out. First, the grade is per engine, and one model can carry several: Mazda's CX-5, Hyundai's Santa Fe and Ram's 1500 each print different grades for different engines. Second, 0W-20 is the grade in most rows, with 0W-30, 5W-30 and 0W-40 alongside it, so a chart that lists only one or two grades for all cars would be missing printed answers. Third, the makers disagree about whether a stand-in is allowed at all: Toyota and Subaru name one, Mazda on its Except U.S.A., Canada page and for its diesel, Mercedes-Benz's C-Class says only 0W-20 for gasoline engines, and Hyundai, Genesis and Kia say any other viscosity could result in engine damage (the Santa Fe and GV70 manuals also recommend a lower-viscosity winter weight oil in some regions in winter and refer you to an authorized dealer or retailer for the type). Fourth, the grade can be shown in several ways: in a table, a sentence, a symbol, a temperature chart, or on a sign in the engine bay, as MINI prints it.

How do thirteen makers print an oil grade, and is there one answer? The owner's manuals of Toyota, Honda, Hyundai, Genesis, Kia, Nissan, Infiniti, Mazda, General Motors, Ram, Subaru, Mercedes-Benz and MINI answer that twelve of the thirteen print the grade engine by engine or model by model, and MINI points to a sign in the engine bay. PulsCar publishes this guide and sells no oil. Hyundai's 2023 Santa Fe prints SAE 0W-20 and 0W-30 for two engines, Mazda's 2021 CX-5 prints 0W-20 and 5W-30 for two petrol engines, Ram's 2026 1500 prints 0W-20 and, for one engine, 0W-40, and Mercedes-Benz's 2022 C-Class says to use only SAE 0W-20. Some manuals print a temperature chart, some a stand-in, some neither. A table that does not name your engine, model year and country is a pointer to the manual, not a replacement for it.

The temperature charts as the manuals draw them

Several makers answer the question of which grade at which temperature with a small chart, and the charts are drawn bars, not tables. We read the chart pages of seven manuals from page images, because the bars are pictures. The words around them are quoted from the page text; the bar ends we judged by eye against the printed scale, so we give no exact temperatures for them.

Hyundai, Genesis and Kia print a table headed Temperature Range for SAE Viscosity Numbers. The sentence above it reads: "When choosing an oil, consider the range of temperature your vehicle will be operated in before the next oil change." The next one tells you what to do: "Proceed to select the recommended oil viscosity from the chart." On the Hyundai and Genesis pages the scale runs from -30 to 50 °C (-10 to 120 °F). In the 2023 Santa Fe the row for the Smartstream G2.5 GDI is one bar labelled 0W-20 and the row for the G2.5 T-GDI is one bar labelled 0W-30, each running the full width of the scale. The 2023 Elantra shows one bar, 0W-20, for its G2.0 Atkinson and G1.6 T-GDi engines, and the 2023 GV70 one bar, 0W-30, for its gasoline engine, again across the whole scale. The Kia page has the same table; its bar is a picture we could not read. Note the phrase before the next oil change: the chart's window is the interval until the oil is changed, not the car's whole life.

Honda's 2026 HR-V manual prints two charts side by side, one for Honda Genuine Motor Oil 0W-20 and one for a commercial oil of 0W-20, both captioned Ambient Temperature, with a scale from -20 to 100 °F (-30 to 40 °C). Each is an arrow with a point at both ends that runs the full width of the scale.

Toyota's 2015 Tacoma manual (the copy Toyota Canada hosts, publication OM04009U) prints one chart per engine, captioned Outside temperature, with marks at 0, 40 and 80 °F (-18, 4 and 27 °C). The 0W-20 arrow for the 2.7 L engine and the 5W-30 arrow for the 4.0 L V6 each run past the marks at both ends.

Subaru's manual MSA5M2403A, in a column headed SAE viscosity No. and applicable temperature, draws a thermometer from -30 to 40 °C (-20 to 100 °F) with two arrows under it, 0W-20 and 5W-30, each drawn across the scale. The text above the table says: "The following table lists the recommended viscosities and applicable temperatures." Mazda's 2021 CX-5 manual draws one arrow for each grade on a thermometer scale from -40 to 40 °C (-40 to 100 °F): 0W-20 for the 2.5, 5W-30 for the 2.5T, and 0W-30 (recommended) and 5W-30 (alternative) for the diesel.

What the charts say, as our reading: in every chart we could read, the printed grade is drawn over most or all of the temperature range the chart shows (Mazda's arrows start just inside the left end of its scale), not as a switch from one grade to another by season. Where Subaru shows two arrows, one is the main grade and the other the stand-in named in the footnote. The charts therefore answer the question on the page in the same way as the tables: for that engine, the manual's grade, across the printed range. They do not say what to do beyond it, and the next section looks at the few places that do.

Beyond the chart: extreme cold, and what the pages say about heat

Most pages we read print no rule for temperatures past the end of the chart, and the exceptions are about cold. General Motors' manuals for the Silverado 1500 (2025) and the Express (2026) say that in an area of extreme cold, where the temperature falls below -29 °C (-20 °F), an SAE 0W-30 oil may be used: "An oil of this viscosity grade will provide easier cold starting for the engine at extremely low temperatures." That is a permission with a temperature attached. The Express manual prints it with its 5W-30 line and the Silverado manual after its 2.7L 5W-30 line; neither manual says which other engines it covers, so ask the dealer if yours is not the one named. The Santa Fe, Elantra and GV70 manuals we read are different in kind: they recommend a lower-viscosity winter weight oil in some regions in winter, name no grade, and refer you to an authorized dealer or retailer for the type.

Dan Holdmeyer's August 2024 article, written by someone retired from an oil company, gives a view on the cold end that is not a maker's: "If startup temperatures are expected to be extremely low, a lower SAE “W” grade could be used so long as the operating temperature SAE grade is maintained." The same article warns about the other direction: "Using a higher SAE “W” viscosity grade could cause great harm if the oil cannot flow through the engine in cold climates." It is an author's opinion in a trade magazine, not a maker's permission, and the maker's manual for your engine still decides.

For heat, the pages we read describe the principle without a second grade. Subaru and the Hyundai group say a higher viscosity is required for lubrication in hot weather, Toyota says a higher hot number may suit high speeds or extreme load, and each of those manuals still prints a grade for the engine. Holdmeyer's article says that engines operating in extreme heat, or under heavy load, "may benefit from a higher SAE grade under these abnormal conditions", and that "I would not recommend using a lower viscosity grade than the OEM recommended SAE grade." Our advice, labelled as ours: if your use really is extreme (a heavy trailer in desert heat, for example), the question to put to the maker's dealer, with your VIN, is whether your engine's manual or a service document names a different grade for it. A forum answer or a website chart is not that.

When the printed grade is not on the shelf: the stand-ins and their exact words

A stand-in is a second grade that a maker allows for a stated case. The pages we read word them differently, and the verbs matter.

Toyota, 2015 Tacoma, 2.7 L engine (SAE 0W-20). "If SAE 0W-20 is not available, SAE 5W-20 oil may be used. However, it must be replaced with SAE 0W-20 at the next oil change." The 4Runner manual (OM35A83U) prints the same pair.
may; must replace at next change
Toyota, 2015 Tacoma, 4.0 L V6 (SAE 5W-30). "If SAE 5W-30 is not available, SAE 10W-30 oil may be used. However, it should be replaced with SAE 5W-30 at the next oil change."
may; should replace at next change
Subaru, MSA5M2403A. In its alternative-oil table, for when the approved Subaru oil is unavailable, 0W-20 synthetic is the required oil (conventional may be used if synthetic is unavailable). A footnote: "If 0W-20 synthetic oil is not available, 5W-30 conventional oil may be used if you need to add oil. However, you should change to 0W-20 synthetic oil at the next oil change."
only to add oil; should change back
Mazda, 2021 CX-5, the page that opens with the heading Except U.S.A., Canada. SKYACTIV-G 2.5: "If SAE 5W-30 engine oil is not available, use SAE 5W-20 engine oil." SKYACTIV-G 2.5T: "If SAE 5W-30 engine oil is not available, use SAE 0W-30 or SAE 10W-30 engine oil." No end point is printed in these lines.
5W-20; or 0W-30, 10W-30; no end point
Mazda, 2021 CX-5, diesel (U.S.A., Canada). The recommended oil is Mazda Genuine SKYACTIV-D SAE 0W-30 Diesel Engine Oil; the alternative, ACEA C3 and SAE 0W-30 or 5W-30, "may be used for oil level maintenance and oil changes", with a strong recommendation to replace it with the genuine oil at the next oil change.
ACEA C3, 0W-30 or 5W-30; replace
Mercedes-Benz, 2022 C-Class; Hyundai, Genesis and Kia, 2023-2024 manuals. No stand-in grade named in the pages we read: "Only use SAE 0W-20 viscosity class engine oils" (Mercedes-Benz, for gasoline engines), and any viscosity other than those recommended could result in engine damage (Hyundai group).
No stand-in grade named

Three points. Toyota's two stand-ins are worded differently inside one manual: must be replaced for the first engine, should be replaced for the second. We keep both, because a maker's must is not a should. Subaru's footnote permits it only to add oil, then asks for a change back. And Mazda's lines on the page headed Except U.S.A., Canada print an alternative without saying when to go back; where a maker prints no end point, ask the dealer. Toyota's RAV4 Hybrid page, with its 0W-16 first choice and 0W-20 stand-in, and the GM, Nissan and Subaru wording on stand-ins, are covered in our guide on which oil your car takes and in the guide on synthetic versus conventional oil.

Ram prints a related rule in its 2026 1500 manual, in the section on synthetic engine oils: "Synthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used." It is about oil on the shelf, not a stand-in: both the mark and the grade must be right. The page before says: "The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils. The API Donut trademark certifies 0W-40 and 5W-40 engine oil." That is a printed link between a mark and a list of grades, which a driver can check on a bottle.

How should I read a stand-in grade a manual allows, and when do I switch back? PulsCar publishes this guide and sells no oil; we read the stand-ins in the 2015 Toyota Tacoma, the 2021 Mazda CX-5 and Subaru's MSA5M2403A manual. Toyota allows SAE 5W-20 for its 0W-20 engine and says it must be replaced with 0W-20 at the next oil change, and allows 10W-30 for its 5W-30 engine and says it should be replaced at the next oil change. Subaru allows 5W-30 conventional oil if you need to add oil, and says you should change back to 0W-20 synthetic at the next oil change. Mazda's 2021 CX-5 manual, on the page headed Except U.S.A., Canada, allows 5W-20 for its 2.5 and 0W-30 or 10W-30 for its 2.5T and prints no end point.

What the makers print about using a different grade

Beyond the stand-ins, the manuals we read speak about any other grade in a few short sentences, and none of them is soft. We give each in the maker's own words and attribute it to the model and year read.

Hyundai (2023 Santa Fe and Elantra), Genesis (2023 GV70) and Kia (2024 SK3) share one sentence: "Using oils of any viscosity other than those recommended could result in engine damage." Nissan (2026 Rogue) and Infiniti (2025 QX60) print "Choosing an oil viscosity other than that recommended could cause serious engine damage." Nissan and Infiniti also tie the choice to a window of use, with the words quoted above on selecting the viscosity based on the temperatures at which the vehicle will be operated before the next oil change. Both makers also print warranty sentences about oil other than as recommended; the guide on which oil your car takes quotes them and we do not repeat them.

Subaru's 2403 manual prints, as a caution on the oil pages: "Use only engine oil with the recommended grade and viscosity." Mercedes-Benz says to use only the grade it names for the C-Class, and to observe restrictions on approved viscosity classes. Ram's 2026 1500 manual prints a caution on earlier API certification levels that can result in engine damage and is not covered by the New Vehicle Limited Warranty, which is about the API level and not the grade; its grade statement is the one above, that oils lacking the correct API trademark and the correct SAE viscosity grade numbers should not be used. Mazda's 2021 CX-5 prints a caution for the diesel: "If engine oil other than the specified oil is used, the Diesel Particulate Filter effective period of use will be shortened or the Diesel Particulate Filter may be damaged." The caution is about the specified oil of that diesel; it does not separate the grade from the engine's other oil requirements.

Oil companies and trade writers say similar things, and we mark them as theirs. Motul's page answers a question on its own FAQ: "Can I switch to a different oil grade? Only if it meets your vehicle’s specifications. Switching without guidance can reduce protection." Another answer on the same page reads: "Too thick or too thin oil can increase wear, reduce efficiency and affect engine longevity." The EngineLabs report on the Mobil 1 discussion quotes the presenter: "Generally speaking, lowering the hot rating of your oil is bad. Going the other direction and increasing the hot rating from your recommended oil isn’t as bad, but is still not recommended." He adds: "If you are putting excessive heat into the oil, like at track days, a higher hot number can be indicated in those situations". Holdmeyer's article opens its discussion of a different grade by saying that the answer is "not a simple yes or no".

What no page says: that a different grade is harmless, or that it is a free upgrade. What the pages do not say either: what happens to a given engine on a given grade. No maker we read prints a failure rate or a wear figure for a different grade, and we do not claim one. The consequences the makers print are few: engine damage as a possibility, warranty language, a shorter diesel particulate filter life (Mazda) and, in Subaru's and Toyota's Tacoma manuals, higher oil consumption when the viscosity is incorrect.

Thicker or thinner: what each source claims, with the source named

Claims about thicker and thinner oil are everywhere, and they carry different weight depending on who makes them. Here are the ones we read, with the kind of source named, so you can weigh them.

Toyota (maker, 2015 Tacoma and 4Runner manual). A higher hot number "may be better suited if the vehicle is operated at high speeds, or under extreme load conditions." A condition, tied to the number after the dash; the manual still prints the grade.
Maker: may be better suited
Subaru and Hyundai, Genesis, Kia (makers). Lower viscosity can provide better fuel economy (Hyundai group) or gives it (Subaru); higher viscosity is required in hot weather. Each prints a grade for the engine and a warning about other viscosities.
Maker: trade-off, grade per engine
US Department of Energy, fueleconomy.gov (government). 10W-30 in an engine designed for 5W-30 can lower mileage by 1% to 2%; 5W-30 in an engine designed for 5W-20 by 1% to 1.5%. Based on a 2001 report; data note revised 2016.
Government: mileage estimate
TotalEnergies UK (oil company). A higher grade "will ensure that the engine is properly protected and sealed in warm weather, although this can come at the loss of the better lubrication and fuel-saving capabilities of lower-grade oils", in its text on non-winter grades.
Oil company: trade-off stated
R. David Whitby, TLT (tribology society magazine, 2017). "Lower oil viscosity means less friction, which usually means better fuel efficiency." And suitability for an engine "depends on the characteristics and operation of that engine."
Trade magazine: depends on the engine
Dan Holdmeyer, TLT (2024). Extreme heat or heavy load may benefit from a higher grade; he would not recommend a lower grade than the maker's.
Author's opinion; names no maker
Motul (oil company, Malaysia page). Higher hot numbers give "a stronger protective film under heat and load, which can be important for heavier vehicles, older engines, or spirited driving."
Oil company: can be important

The pattern in these claims is conditional: may, can, usually, depends. Not one of them, from a maker or anyone else, says a thicker oil is better in general, and the one source that ties older engines to a hotter grade (Motul) says a stronger film can be important for them. We did not find in these documents a statement about high-mileage engines from a maker. The Department of Energy's estimate is about fuel economy only, and it says that a thicker grade than the recommended one can lower mileage.

Our reading of Whitby's point above, that suitability depends on the engine: it is the line makers draw when they print a grade for each engine.

The thin end: 0W-16, 0W-12 and 0W-8

The grade list grew at the thin end in the 2010s. Wikipedia's account of J300 says grade 16 was added in 2013 and grades 8 and 12 in 2015. Whitby's January 2017 article says the latest J300 then contained the viscosity limits for 0W-16, 0W-12 and 0W-8. The hot-grade table above shows what the new numbers are: grade 16 is a range of 6.1 to under 8.2 mm2/s at 100 °C, grade 12 is 5.0 to under 7.1, grade 8 is 4.0 to under 6.1.

A grade in the standard is not the same as a grade an oil can be sold with a mark for. API's page on oil categories says of ILSAC GF-6B that it "Applies only to oils having an SAE viscosity grade of 0W-16." Holdmeyer lists the other side: GF-6A oils "are limited to SAE 0W-20, SAE 0W-30, SAE 5W-20, SAE 5W-30 and SAE 10W-30" to display the Starburst symbol, and GF-6B only allows SAE 0W-16 to earn the Shield. Chevron's Havoline page on the newer GF-7 says GF-7A is "Designed for commonly used viscosity grades like SAE 0W-30, 5W-30, 10W-30, 0W-20, and 5W-20", and that GF-7B is specific to SAE 0W-16 and "Lower viscosity grades like 0W-12 and 0W-8 are not covered under GF-7." In other words, by that page an oil of 0W-12 or 0W-8 is outside what GF-7 covers. Which engines take the thin grades is the maker's decision; Toyota's RAV4 Hybrid page, which prints SAE 0W-16, is quoted in the guide on which oil your car takes.

EngineLabs, reporting on the Mobil 1 video in 2020, warns about the temptation: "you can’t just go out and drain your 10W-30 and toss in some 0W-16 and pick up power and/or fuel economy." It adds, in its own words: "The tolerances and clearances in your engine are designed specifically around the manufacturer- (or builder-) recommended oil viscosity." Our reading: that is the same line as the makers draw, from a trade publication reporting a discussion held in partnership with Mobil 1, and it is not a measurement.

Where your own grade is printed

The grade for your car is in your manual, and the makers locate it in several places. Hyundai, Genesis and Kia put it on a page headed Recommended SAE viscosity number, after the lubricants and capacities table. Honda puts it in the maintenance chapter, under Recommended Engine Oil. Nissan puts a picture of the API service symbol with the grade in its engine oil recommendation, and Toyota puts it in its specifications chapter under Engine oil selection. MINI's 2025 Countryman manual says the suitable viscosity grade "is indicated on a sign in the engine compartment." Our guide on which oil your car takes says that none of the pages it read prints the grade on the oil filler cap or a sticker; MINI's page is a printed statement that a sign carries it, and we read one MINI manual only.

Motul's page says to check "Your owner’s manual", "The oil filler cap under the bonnet" and "Service documentation", which it says "usually specify the recommended viscosity, such as 5W-30 or 10W-40." That is an oil company's statement from a page for another market, and a cap marking is a clue to confirm in the manual, not an answer.

At the counter or the shop: what to say, and what a good answer sounds like

The pages above give you a few questions worth asking. This list is our advice, not a maker's: it turns what the manuals print into questions you can put to a parts counter or a service desk.

At the counter, say this: "My manual lists a grade for my engine, model year and country. Which grade is on this bottle, and which specification does it meet?" A good answer names a grade (for example 0W-20) and a mark or approval, and it matches the line in your manual. The bottle's mark and the grade are separate: Ram's manual, quoted above, ties the API Starburst to a list of grades, so you can check the two against each other.

If the answer is a different grade, say this: "Does my manual allow that grade for my engine, and for how long?" If your manual names a stand-in, as Toyota's, Subaru's and Mazda's do, the answer is a condition and, where printed, a deadline. If it names none, as the Mercedes-Benz C-Class and Hyundai group manuals we read name none, the honest answer is that the printed grade is the grade.

If the shop says a thicker oil is better for a car with some age on it, say this: "Which page of the maker's manual or a maker's service document says so for my engine?" The sources we read make conditional claims in general (may, can, depends on the engine) and print one grade per engine. A statement that no maker's document backs is an opinion.

If a grade your manual does not name is already in the engine, ask the dealer with your VIN whether to change it now.

What we could not read

A guide like this should say what it could not see. We read the oil sections of the owner's manuals of thirteen makers' brands (Infiniti's oil pages repeat Nissan's wording, and Genesis's and Kia's paragraph on viscosity repeats Hyundai's, so those confirm a pattern more than they add a second opinion). We could not find a Ford owner's manual we could read, and Volkswagen, Audi, BMW (other than the MINI manual, which BMW Group hosts) and Volvo pages gave us no grade text we could use. We could not read the pages of Mobil, Valvoline, Pennzoil, AMSOIL and Shell on viscosity, nor those of NAPA, O'Reilly and RepairPal. The standard itself, SAE J300, is sold by SAE, and we did not buy it; its limits here come from Wikipedia's article and an STLE article, as set out above. Petro-Canada's handbook, Anton Paar and Engineers Edge returned errors or refused us. The chart pictures in Kia's online manual could not be read from the page text. We did not read the GM Duramax diesel supplement or any diesel manual page other than Mazda's CX-5 diesel entry.

Three composite situations

These are composite scenarios, not individual customers. Each is built only from facts printed above.

The turbo that is not the base engine. An owner of a 2023 Hyundai Santa Fe looks up a chart on a parts website that lists SAE 0W-20 for the model. Their car has the 2.5 turbo. The Santa Fe manual's chart prints 0W-20 for the Smartstream G2.5 GDI and 0W-30 for the Smartstream G2.5 T-GDI, and the manual says to use the viscosity from the chart and that any other viscosity could result in engine damage. What they do: read the row for their engine, buy the grade that row prints, and keep the manual page. The website's chart was a pointer; the engine decided.

The shelf without the grade. An owner of a 2015 Toyota Tacoma with the 2.7 L engine finds that the shop is out of 0W-20 and offers 5W-30. The Tacoma manual allows SAE 5W-20 if 0W-20 is not available, with the words must be replaced with SAE 0W-20 at the next oil change, and it prints no 5W-30 stand-in for that engine (its 5W-30 line belongs to the 4.0 L V6). What they do: ask the shop for the grade the manual names, or ask the Toyota dealer with their VIN whether another grade is acceptable, and not take 5W-30 on the shop's say-so alone.

The same model, two engines. An owner of a Ram 1500 reads on a forum that the truck takes 0W-20. Their engine is the 3.0L High Output. The 2026 Ram 1500 manual prints SAE 0W-20 for the 3.0L Standard Output, the 3.6L and the 5.7L, and SAE 0W-40 with the API Donut for the 3.0L High Output. What they do: confirm which engine they have, read that line, and check the bottle for the Donut the manual names for it.

If the red oil pressure light comes on

The grade questions in this guide are about oil in a healthy engine. A warning light is a different matter. If the red oil pressure light comes on while you drive, stop in a safe place and switch the engine off: Mazda, Nissan, Infiniti and Subaru print a warning against running the engine with that light on, and Nissan, Infiniti and Subaru say to contact a dealer. Our advice, not a maker's: once it is safe, wait as your manual says, then check the oil level; if it is low, add oil as your manual says, and if the level was not low, or the light stays on after adding oil or returns, do not drive on and have the car towed.

The makers' words, from the manuals we read: Subaru's 2403 manual says "Do not operate the engine with the oil pressure warning light on." Mazda's 2021 CX-5 manual says "Do not run the engine if the oil pressure is low." Nissan's 2026 Rogue manual says the light may mean low oil pressure, tells the driver to stop the vehicle safely and stop the engine immediately, and says running the engine with the light on "could cause serious damage to the engine." Infiniti's 2025 QX60 manual says running the engine with the light on "could cause serious damage to the engine almost immediately." Our reading: a grade question can wait for the next oil change; the light cannot. The guide on the low oil pressure warning covers the causes.

Your action plan

Do these in order, and stop when you have your answer.

  1. Find three facts about your car: the engine (ask the dealer, quoting your VIN, if you are not sure), the model year and the country edition of your manual.
  2. Open the manual's chapter on lubricants and capacities, or specifications, or the maintenance chapter, depending on the maker (Hyundai, Genesis and Kia put the grade on a page headed Recommended SAE viscosity number; Honda under Recommended Engine Oil; Toyota under Engine oil selection).
  3. Find the line or chart row for your engine. If there are several grades, the manual says which applies to which engine; take the one for yours.
  4. If the manual names a stand-in, write down its condition and, where printed, the deadline (the next oil change, or only to add oil). If it names none, the printed grade is the only one.
  5. At the counter, ask which grade and which specification are on the bottle, as above, and compare them with the manual's line.
  6. Treat a website chart, a forum post or a shelf sign as a pointer to check against the manual, not as an answer.
  7. If the red oil pressure light comes on while you drive, stop in a safe place and switch the engine off: Mazda, Nissan, Infiniti and Subaru print a warning against running the engine with that light on, and Nissan, Infiniti and Subaru say to contact a dealer. Our advice, not a maker's: once it is safe, wait as your manual says, then check the oil level; if it is low, add oil as your manual says, and if the level was not low, or the light stays on after adding oil or returns, do not drive on and have the car towed.

What this page cannot tell you

It cannot tell you the grade for your car. Only the manual for your engine, model year and country, or your maker's dealer with your VIN, can. We read thirteen makers' brands and could not read many others, so a large share of makes, models and years is not here. We did not test oils, do not rank them and make no claim that a grade is better. The J300 numbers come from Wikipedia and a trade magazine because the standard is sold; check the standard if you need exact limits for work. The chart bars were read by eye from page images, so we give no exact temperatures for where a bar ends. The oil-company, government and trade pages are statements by their authors, and the one trade report (EngineLabs on a Mobil 1 partnership) reports a presenter's view and adds its own. We did not measure oil at any temperature. For what an oil change costs and how often it is due, the oil change cost guide and the guide on how often to change oil carry their own dated sources.

Sources and documents

Manuals were read on 11 November 2026 (the Elantra and GLE copies on 12 November), with chart pictures re-read from the same documents on 15 November 2026; each other page carries its own read date. Where a page carried no date or did not name the model year, we say so.

  1. SAE J300 and its grades: Wikipedia, SAE J300 (an encyclopedia article that cites the April 2021 edition; read 15 November 2026); R. David Whitby, Engine oil viscosity, TLT Worldwide, January 2017, Society of Tribologists and Lubrication Engineers (read 15 November 2026); Dan Holdmeyer, Automotive engine oil specifications, TLT Lubrication Fundamentals, August 2024 (read 15 November 2026).
  2. Oil companies, each their own statement and read 15 November 2026: Castrol, What is 0W-20 motor oil; TotalEnergies UK, Motor oil viscosity grades explained; Motul, What do engine oil numbers mean (Malaysia page); Chevron Lubricants, Havoline GF-7 motor oils (undated; read 11 November 2026).
  3. Standards bodies, government and trade press: American Petroleum Institute, API Oil Categories and Latest Oil Categories and Classifications (read 11 November 2026); US Department of Energy, fueleconomy.gov, Keeping Your Vehicle in Shape (read 15 November 2026; the page's own data note says revised 27 June 2016); EngineLabs, Three Questions About Ultra-Thin Oil With Engineering Explained, 4 September 2020 (read 15 November 2026).
  4. Toyota, owner's manuals: 2015 Tacoma, OM04009U, hosted by Toyota Canada and 4Runner OM35A83U. Honda: 2026 HR-V owner's manual, a copy hosted by a dealer and the 2013 Civic manual, Honda Canada.
  5. Hyundai, 2023 Santa Fe and 2023 Elantra owner's manuals; Genesis, 2023 GV70; Kia, online manual model code SK3, 2024, US English: Recommended lubricants and capacities and Recommended SAE viscosity number (this page read 15 November 2026).
  6. Nissan, 2026 Rogue; Infiniti, 2025 QX60; Mazda, 2021 CX-5.
  7. General Motors, Chevrolet owner's manuals: 2025 Silverado 1500, 2026 Equinox and 2026 Express (a copy hosted by a third-party site); Ram, 2026 1500 owner's manual.
  8. Subaru, owner's manual MSA5M2403A (most pages marked as edited in December 2022; the chart is on printed page 569). Mercedes-Benz, 2022 C-Class and 2022 GLE owner's manuals; MINI, 2025 Countryman manual.
  9. What we could not read, and so did not quote: Ford's owner's manuals; the grade pages of Volkswagen, Audi, BMW (apart from the MINI manual), Volvo; Mobil, Valvoline, Pennzoil, AMSOIL and Shell viscosity pages; NAPA, O'Reilly and RepairPal; the SAE J300 standard; Petro-Canada's handbook; Anton Paar; Engineers Edge; Kia's chart picture.
  10. PulsCar homepage (publisher).

Prices verified: this page carries no prices; see the oil change cost guide · Technical documents verified: November 2026

Saw a figure or a source that differs from this page? Email [email protected] with the source and its date.